Manual EN - Prodance
Contents
1. LL AVIONS PROFESSIONAL __ lt E Junostraat 2 6468EW Kerkrade The Netherlands www americandj eu info americandj eu 1 Handle 2 Bracket 3 Bracket locking screw 4 Plug 5 Power socket 6 Reflector 7 Lamp 8 Lamp socket 9 Lens 10 Handle screw Q7 11 Colour frame THEATER SPOT 300 500 650 1000 2000 For your own safety please read this user manual carefully before you start up and use IMPORTANT SAFETY INSTRUCTIONS CAUTION Be careful with your operations With a dangerous voltage you may suffer a dangerous electric shock when touching the wires Make sure that the available voltage is not higher than stated in this manual If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature This device falls under protection class therefore it is essential that the blue conductor gets connected to earth The electric connection must be carried out by a qualified employee Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard Shields2. lenses or ultraviolet screens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired for example by cracks or deep scratches Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord DANGER OF BURNING Never touch the device during the operation The housing heats up to the housing temperature T surace Don t switch the device on and off in short intervals as this would reduce the lampss life HEALTH HAZARD Never look directly into the light source as sensitive persons may suffer an epileptic shock especially meant for epileptics Keep away children and amateurs from the device There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers This device is a lighting effect for creating decorative effects this fixture is only allowed to be operated with an alternation current of max 230V 50Hz 500W and was designed for indoor use only When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of othe
3. TION E Junostraat 2 6468EW Kerkrade The Netherlands www americandj eu info americandj eu z x MADE IN CHINA MADE IN CHINA
4. arried out by a qualified electrician In order to connect the device to the mains you have to install a power plug The occupation of the connection cables is as follows International Yellow Green Earth The earth has to be connected Connect the device to the mains with the power plug If the device will be directly connected with the local power supply network a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation In general lighting effects should not be connected to dimming packs DANGER TO LIFE Before taking into operation for the first time the installation has to be approved by an expert OPERATION After you connected the fixture to the mains the lamp will be on You can adjust the beam angle by pulling and pushing the handle screw through the track beneath the device CLEANING AND MAINTENANCE The following points have to be considered during the inspection 1 All screws used for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on housings fixations and installation spots ceiling suspension trussing 3 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any saf
5. ety problems have to be removed DANGER TO LIFE Disconnect from mains before starting maintenance operation We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents The interior of the device should be cleaned at least annually using a vacuum cleaner or an air jet There are no serviceable parts inside the device except for the lamp Maintenance and service operations are only to be carried out by authorized dealers Please refer to the instructions under Replacing the lamp Should you need any spare parts please use genuine parts If the power supply cable of this device becomes damaged it has to be replaced by authorized dealers only in order to avoid hazards Should you have further questions please contact your dealer TSP 300 500 TECHNICAL SPECIFICATIONS Power supply Max 230 240V AC 50Hz Power consumption Dimensions Lx W x H Weight Fitting lamp TSP 2000 TECHNICAL SPECIFICATIONS Power supply Max 230V AC 50Hz Power consumption Max 2000W Dimensions L x W x H 370x250x370mm Fitting lamp GY16 2000W halogen lamp Maximum ambient temperature ta 25 C 2 O Maximum housing temperature ts 260 C Minimum distance Bm TSP 650 1000 TECHNICAL SPECIFICATIONS Power supply Max 230 240V AC 50Hz Power consumption Max 1000W Dimensions L x W x Hj 3 0x250x370mm Minimum distance LA
6. f all installation material and the device The device has to be installed out of the reach of people If the device shall be lowered from the ceiling or high joists professional trussing systems have to be used The device must never be fixed swinging freely in the room Caution Devices may cause severe injuries when crashing down If you have doubts concerning the safety of a possible installation do NOT install the device DANGER OF FIRE When installing the device make sure there is no highly inflammable material decoration articles etc within a distance of min 0 5 M Mount the device with the mounting bracket to your trussing system using an appropriate clamp The hole in the mounting bracket has a diameter of 13 mm 1 TRUSSING For overhead use always install a safety rope that can hold at least 2 SAFETY ROPE 10 times the weight of the fixture You must only use safety ropes E with screw on carabines Pull the safety rope through the hole in 4 SAFETY SCREW the mounting bracket and over the trussing system etc Insert the 5 HOOK end in the carabine and tighten the safety screw Adjust the desired inclination angle via the mounting bracket and fix the fixation screws DANGER TO LIFE Before taking into operation for the first time the installation has to be approved by an expert or by qualified ENGINEERS TECHNICIANS only Connection with the mains DANGER TO LIFE The electric connection must only be c
7. nded Please follow the lamp manufacturer s notes Do not install lamps with a higher wattage Lamps with a higher wattage generate temperatures the device was not designed for Damages caused by non observance are not subject to warranty For the installation you need one GY9 5 halogen lamp with up to max 500W Procedure Step 1 Unscrew the handle screw on the rear of the device HANDLE f Step 2 Push out the cover to the back SCREW Step 3 Remove the old lamp i Step 4 Insert the same type lamp into the lamp socket Step 5 Replace the cover and screw the handle screw Installing The installation of the device has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails When rigging derigging or servicing the fixture staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden The device should be installed outside areas where persons may walk by or be seated IMPORTANT OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE including but not limited to calculation working load limits installation material being used and periodic safety inspection o
8. rs The symbol v determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 1 meters Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Always fix the fixture with an appropriate safety rope The maximum ambient temperature T4 must never be exceeded Operate the device only after having become familiar with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please consider that unauthorized modifications on the device are forbidden due to safety reasons If this device will be operated in any way different to the one described in this instruction the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock lamp explosion crash etc Replacing the lamp DANGER TO LIFE Only install the lamp with the device switched off Unplug from mains before CAUTION The lamp has to be replaced when it is damaged or thermally deformed due to the heat The lens must be replaced if it is visibly damaged and therefore operating with reduced efficiency Before replacing the lamp unplug mains lead and let the lamp cool down approx 5 minutes During the installation do not touch the glass bulbs bare ha
Download Pdf Manuals
Related Search