Leica Steer Ready Kit Installation Manual
Contents
1. Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 27 Description 9 2 Permitted Use Adverse Use Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 29 Safety Directions General The Leica Steer Ready Kit is to be used solely in combination with Leica moJoRTK system Therefore it s mandatory to also observe the directions and instructions contained in the Leica mojoRTK User Manual The following directions should enable the person responsible for the product and the person who actually uses the equipment to anticipate and avoid operational hazards The person responsible for the product must ensure that all users understand these directions and adhere to them Intended Use e The Leica Steer Ready Kit is exclusively developed for usage in agriculture or forestry by persons in control e The Leica Steer Ready Kit is only intended to be fitted to agricultural tractors It is not permitted to install this product in any other vehicles e Use of the product without instruction e Use outside of the intended limits e Disabling safety systems e Removal of hazard notices e Opening the product using tools for example screwdriver unless this is specifically permitted for certain functions e Modification or conversion of the product e Use after misappropriation e Use of products with obviously recognizable damages or defects e Use with accessories from other manufacturers without the p2. N Da nger Before beginning this section of the installation please ensure that the vehicle is turned off and a The following will give a general outline of the steps necessary to install the SRK Controller assembly 5 1 SR Controller Bracket Mounting Step 1 Working from the rear of the vehicle remove the rear panel by undoing the bolts on either side of the cab as shown and lifting Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 13 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 14 Step 2 To locate the mounting position shown ght and lift the rubber flap The SR Controller Bracket slotted bolt hole will align with an existing bolt located on the edge under the rear window of the Cab towards the middle Step 3 Once located mount the SR Controller Bracket to the vehicle Use the M8 nut and washer to attach it to the mounting bolt Step 4 Mount the Steer Ready Controller to the bracket using the M6 bolts and washers as supplied 6 Installing the Steering Sensor 6 1 Mounting the Steering Sensor DANGER DO NOT START tag is attached to the ignition N Da nger Before beginning this section of the installation please ensure that the vehicle is turned off and a OTHER that any covers or other items that have been removed to this point in the installation are in a safe The tractor needs to be started and stopped during the mounting of the steering sensor Ensure
3. N Warning position and that the tractor is in a generally safe condition before it is started Step 1 Refer to Section 4 3 of the equipment list to ensure that you have the correct parts Step 2 Using the 45mm 5 bolt attach the cable end of the linear sensor 676001 to the linear sensor mounting bracket 676004 H Linear Sensor Mounting Bracket Step 3 Join the two parts of the shaft end bracket 676008 using the two M5 x 25mm bolts two Nyloc nuts and four washers as shown Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 15 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot Step 4 Attach the non sensor end of the linear sensor to the shaft end bracket assembly using the 45mm M5 bolts as shown Mounting Bracket M5 Bolt Step 5 Start the tractor and turn the steering wheel hard lock to the right Stop the tractor Step 6 Using the smaller worm drive clamp mount the shaft end bracket of the linear sensor assembly to the most left point of the left side steering ram as shown 16 Step 7 Using two larger worm drive clamps mount the other end of the linear sensor assembly to the cylinder of the steering ram as shown The sensor should be mounted just under full extension at full lock Step 8 Start the tractor again and slowly turn the wheels from lock to lock Check that there are no obstructions and the steering ram can not force the sensor past its
4. ER EE EE Ea a eee ee EEEa eee 10 VM ME PA TES e a 11 5 CONTROLLER INSTALLATION 13 5 1 SR CONTROLLER BRACKET MOUNTING EE 13 6 INSTALLING THE STEERING SENSOR hd deu ER Ud oua ru kay DE ERR eb c RAE 15 re SES ze TRO 15 7 ROUTING TRE WIRING PAS oM IDEO PRA D LISTE DUE 18 7 1 CONNECTING TO THE SR CONTROLLER C NERONE RR 18 7 2 ROUTING THE HYDRAULIC VALVE CABLE ER Orr d tabs eR d 19 7 3 ROUTING THE ING CAB FARIS Si ERIS PARRA bu acia 21 7 4 ROUTING THE WHEEL ANGLE SENSOR 5 23 7 5 INSTALLING THE ENGAGE SWITCH Rn RR RC ORG 24 Z0 OUTING THE OVERRIDE eer cee 25 PM
5. Zone 50 50 m 2ni 20 m gt m Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 35 With exemption of the driver no other person should ride in the drivers area of the vehicle fitted with a Leica Steer Ready Kit Additional persons could distract or block visibility of the driver from operating and observing the Leica Steer Ready Kit which could lead to dangerous situations The presence of a rider on a passenger seat is only acceptable for brief observations or for training purpose The passenger seat is never considered a children seat Only persons especially experienced with the operation of the machine should be considered for schooling on a machine which is fitted with a Leica Steer Ready Kit Pay special attention that no children are near or on the vehicle which is fitted with a Leica Steer Ready Kit especially when the Leica Steer Ready Kit is active Children are unpredictable and supervision is limited when operating the Leica Steer Ready Kit They might be exposed to additional danger Before starting field work make yourself comfortable with the use of the Leica Steer Ready Kit and the vehicle As soon as the Leica Steer Ready Kit is activated an adult responsible person has to be in charge of supervision and monitoring In dangerous situations it is always safer to disengage the Leica Steer Ready Kit and drive by hand in order to avoid personal injury or material damage At no ti
6. authorized service workshops are entitled to repair these products Beware of inadequate steering if machine is defective like after a crash or other damaging events or alterations to the machine Precautions Periodically perform control measurements and field adjustments on the machine as specified in the User Manual While steering or navigating the machine accidents may occur due to a the operator not paying attention to the surroundings persons ditches traffic etc or b malfunctions of a system component interference etc Precautions The operator assures that the machine is operated guided and monitored by a qualified user e g driver The user has to be able to take emergency measures for example an emergency stop The absence of instruction or the inadequate imparting of instruction can lead to incorrect or adverse use and can give rise to accidents with far reaching human material financial and environmental consequences Precautions All users must follow the safety directions given by the manufacturer and the directions of the person responsible for the product During dynamic applications there is a danger of accidents occurring if the user does not pay attention to the environmental conditions around for example obstacles excavations or traffic Precautions The person responsible for the product must make all users fully aware of the existing dangers Inadequate securing of the work site can lead
7. is located on the right side of the vehicle s cab below console Connect the Power supply to the In Cab harness and connect it to the power connector Note The power cable needs to be tucked behind the vehicle cab lining 7 8 Wiring Check Before switching the controller on use the diagram in Section 8 to check the wiring of the system connectors should be inserted until they have clicked 7 9 Secure Cable Harnesses Once the cabling is correct use the supplied cable ties to secure the harnesses Where possible group the cables to use only one cable tie Secure the cables to other cable harnesses or vehicle structure only when it will not cause the cable to be damaged If cables are too long wind them up appropriate length and tie together Tuck all cables in the cab away or under the floor lining so they cannot be tripped on or damaged Wiring Harness Diagram 676172 676175 BE __ Wheel Angle N Sensor 15 676001 DC Bonon To Valve Steer Ready Controller 676033 To Override Sensor Exterior to Cab Interior to Cab mojoRTK Console 676178 To Machine Power
8. of the equipment list to ensure that you have the correct Wiring Harness Part No 676181 Step 2 Working from the LHS of the vehicle the Hydraulic Steering Control Valves of the vehicle are located on the side of the chassis just in front of the Cab Unscrew the bolts to remove the cover w these Iboltsktoyremove mM behind Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 19 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 20 Step 3 The Hirschmann plug connections are on the bottom side of the solenoid Plug the Hirschman plugs to the solenoids Note The cable has two Hirschmann plugs one is marked Right and the other Left The one marked Left connects to the front solenoid of the valve and the one marked Right connects to the solenoid at the rear of the valve Step 4 Working from this connection with the hydraulic valve route the cable under the Cab to the SR Controller Ensure that it is suitably positioned and secured with the cable ties and connect to the SR Controller Harness that was fitted in section 7 1 7 3 Routing the In Cab Harness Inside the vehicle cab there are essentially four connections to be made with the In Cab Wiring Harness They are the connection to the Leica moJoRTK console the auto engage switch the manual override cable and the power supply cable Step 1 Refer to Section 4 1 of the equipment list to ensure that you have the correct In Cab Wiring Har
9. to dangerous situations for example in traffic on building sites and at industrial installations Precautions Always ensure that the work site is adequately secured Adhere to the regulations governing safety and accident prevention and road traffic If the product is improperly disposed of the following can happen If polymer parts are burnt poisonous gas are produced which may impair health By disposing of the product irresponsibly you may enable unauthorized persons to use it in contravention of the regulations exposing themselves and third parties to the risk of severe injury and rendering the environment liable to contamination Precautions The product must not be disposed with household waste Dispose of the product appropriately in accordance with the national regulations in force in your country Always prevent access to the product by unauthorized personnel Product specific treatment and waste management information can be downloaded from the Leica Geosystems home page at http www leica geosystems com treatment or received from your Leica Geosystems dealer On public roads and drives always disengage the Leica Steer Ready Kit via the power switch For safety reasons it is better if you keep one hand on the steering wheel when using the Leica Steer Ready Kit at speeds over 6 mph 10 km h In case of malfunction you are able to take action immediately Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 31 i
10. E eU cu 399 2 458 em 26 Dea le qe a a en ee 26 7 9 SECURE CABLE HARNESSES 26 8 WIRING HARNESS 1 27 DIRECHON 28 9 1 9 2 9 3 9 4 9 5 GENERA 28 INTENDED D E es oct dede Lf 28 A CT 29 RESPONSIBILITIES 29 cote E LU E i CP ANE 30 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 5 1 Benefits To understand the user manual Use only original parts CE Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 6 Product Overview The Leica Steer Ready Kit is the first step in getting your equipment Leica moJoRTK ready It consists of a Steer Ready Controller amp associated Wiring Harness brackets and bolts which will form the foundation of your new auto steer solution The Leica Steer Ready Kit is designed to be used in conjunction with the Leica mojoRTK console The in
11. Version 1 2 0 English Leica Steer Ready Kit Installation Manual Tractor Model Case Magnum MX Trimble Autopilot Auto steer Retrofitted when it has to be right Seica Geosystems Introduction Purchase Product Identification Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 2 Congratulations on your purchase of a new Leica Steer Ready Kit This manual contains important safety directions as well as instructions for installing the product and operating it Refer to the Safety Directions for further information Read carefully through the Installation Manual before you begin operation of machinery The Leica Steer Ready Kit is to be used solely in combination with Leica mojoRTK system Therefore it s mandatory to also observe the directions and instructions contained in the Leica mojoRTK User Manual To ensure safety when using the system please also observe the directions and instructions contained in the User Manual and Safety Handbook issued by the e Agricultural machinery manufacturer This manual describes how to install the Leica Steer Ready Kit Even if you have installed other Leica Geosystems products before we recommend you read this manual to ensure correct installation of this product The model and serial number of the Leica Steer Ready Kit are indicated on the packaging Please enter them here and always refer to this information when you need to contact your agency or Leica Geosystems auth
12. anel then to the rear right behind the cab roof lining Step 9 Remove the cab pillar panel and conceal the cable behind this panel Ensure that all connectors are easily accessible for further installation Any excess cable can be rolled into a gentle loop and secured using cable ties 7 4 Routing the Wheel Angle Sensor Harness This Section is not applicable to SRK Open kits If installing an SRK open system proceed to Section 7 5 Step 1 Refer to Section 4 1 of the equipment list to ensure that you have the correct Wiring Harness Part No 676175 Step 2 From the Linear Sensor mounted in Section Error Reference source not found connect the Wheel Angle Sensor extension cable to the linear Sensor cable Step 3 Route the extension cable under the cab to the SR controller cable installed in Section 7 1 connect to this cable If the cable is too short use both extension cables to reach Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 23 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 7 5 Installing the Engage Switch Step 1 Refer to Section 4 1 of the equipment list to ensure that you have the auto steer engage switch Part 676191 Step 2 The auto engage switch 15 to be installed in the panel on the right armrest There should be a Spare place for a switch with a blank insert in the hole The blank can be removed by lifting it with a Small flat blade screw driver Step 3 Feed the cable for the a
13. cal authority regulations could be voided This also applies to the removal of factory applied seals The Leica Steer Ready Kit supports you and improves your efficiency while working in the field The responsibility for quality and work related results rests as always with the driver As common with most all machinery the basic rule applies The more exact the system is adjusted calibrated and operated the higher the quality of results will be CE 3 General N Caution Pre Installation Vehicle Preparation 1 Park the vehicle on a hard level surface and block the front and rear wheels 2 Align the steering wheels straight ahead 3 Remove all dirt and trash from the areas of the vehicle where the Leica Steer Ready Kit will be installed 4 Lower the 3 point hitch to its lowest point Consult the Tractor s Operator s Manual for assistance Note The left and right hand sides of the vehicle are referenced while standing behind the vehicle facing the normal direction of travel System Description The Leica Steer Ready Kit is capable of interfacing to existing actuators and sensors to steer vehicles like tractors and other self propelled machines in agriculture and forestry applications The Leica Steer Ready Kit is composed of the Steer Ready Controller and associated cabling The Leica Steer Ready Kit 5 designed to interface to the Leica moJoRTK system via CAN bus The Leica Steer Ready Kit is designed to assist the machine operato
14. me should there be any person within the danger zone after the Leica Steer Ready Kit is activated At any sign of danger the operator should deactivate the Leica Steer Ready Kit immediately He has to ask any person within the danger zone to leave promptly Only when there are no more people within the danger zone can he re activate the Leica Steer Ready Kit For service and control duties only authorized persons can enter the danger zone after verbal confirmation with the operator Such people have to be clearly informed about possible dangers before entering the danger zone All activities between the operator and these persons should be discussed before hand All service adjustment and control duties on this Leica Steer Ready Kit should only take place if technically possible on a parked vehicle with the engine turned off N Danger Prepare for possible emergencies People present within the danger zone are exposed to serious bodily harm or even death People could be run over in case of malfunction of the machine The operator is obligated to stop the vehicle as soon as people enter the danger zone e Always have a fire extinguisher and First Aid kit at hand e Always have actual emergency phone numbers for Fire department ambulance and doctor handy Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 33 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 34 Purchase Returns Leica Geosystems offers customers the abili
15. mechanical stops Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 17 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 18 7 Routing the Wiring 7 1 Connecting to the SR Controller Da nger Before beginning this section of the installation please ensure that the vehicle is turned off and a ET DO NOT START tag is attached to the ignition It is essential that the cables are routed throughout the vehicle in a position that is away from excessive vibration amp heat sources such as exhaust manifolds and or radiators Also ensure that there is enough length in the cable to prevent stretching or excessive tension whilst the vehicle is in normal operation making sure that it can be mounted securely Step 1 Refer to Section 4 1 of the equipment list to ensure that you have the correct Wiring Harness Part No 676172 Step 2 Locate the Steer Ready Controller that was mounted to the vehicle in Section 5 of this manual Step 3 Connect the black Deutsch connector of the Wiring Harness to the black rimmed socket of the Steer Ready Controller Step 4 Connect the grey Deutsch connector of the Wiring Harness to grey rimmed socket of the Steer Ready Controller Step 5 Leave the other end of the SR Controller wiring freely available as each of these available connectors will be used for the various components of the Leica Steer Ready Kit 7 2 Routing the Hydraulic Valve Cable Step 1 Refer to Section 4 2
16. n Case Power Cable 676178 Trimble Override cable 676033 ES 3 676181 Hydraulic Cable cm Description M8 Nyloc Nut Flat Washer Qty Description Part 1 Trimble Hydraulic Valve Cable 676181 4 3 SRK C 676022 SRK Open kits do not include these components For more information consult your dealer Qty Description Part Qty Description Part 1 Linear Sensor 250mm 676001 1 Linear Sensor l Linear Sensor Mounting Bracket 676004 l Linear Sensor Mounting Bracket 676004 676004 Qty Description Part 1 Worm Drive Clamp 32 50mm 676003 Qty Description Description Qty Description 1 Worm Drive Clamp 70 90mm 676002 1 Linear Sensor Shaft End Brackets 676008 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 11 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot diy 676175 4pin Extension Qty Description Part 2 Wheel Angle Sensor Extension Cable 676175 676175 4pin Extension 12 5 Controller Installation Before commencing the Installation lower the 3 point linkage of the tractor to its lowest point and turn the front wheels of the tractor so that they are positioned straight ahead Consult the Tractor s Operator s Manual for assistance Q DANGER DO NOT START tag is attached to the ignition
17. ness Part No 676186 Step 2 Locate the entry point into the vehicle s cab at the rear right side of the cab This will provide entry into the cab space near the implement controls Step 3 Make a small hole in the rubber and feed the end of the long cable of this harness through the hole from inside the cab Step 4 Locate the Steer Ready Controller Harness that was fitted in Section 7 1 and connect to the cable of the In Cab harness that was fed through the hole Any excess cable can be rolled into a gentle loop and secured using cable ties Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 21 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 25 Step 5 Locate the mounting position of the associated Leica mojoRTK console which will typically be the vehicle s factory fitted radio DIN slot Step 6 Remove the Leica mojoRTK console from the DIN slot using the tools supplied in the Leica mojoRTK console kit and plug the CAN cable Part 675591 into ISO C plug in the rear of the unit If the Leica console has not yet been installed refer to the Installation Manual for this product and prepare to install it now If this product is not available for install Skip Step 6 and return to it later Step 7 Connect the other end of the CAN cable the CAN extension cable Part 676030 Connect the extension cable to the In Cab harness Step 8 The CAN cable and its extension can be fed behind the p
18. orized service workshop Make Model Serial No _ Symbols Symbols used in this manual have the following meanings Indicates an imminently hazardous situation which if not avoided will result in death or Da n ger serious injury Indicates a potentially hazardous situation or an unintended use which if not avoided Wa lI could result in death or serious injury Indicates a potentially hazardous situation or an unintended use which if not avoided Ca ution may result in minor or moderate injury and or appreciable material financial and environmental damage Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner Note The absence of specific alerts does not mean that there are no safety risks involved Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 3 Table of Contents Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 4 L PRODUCT OVERVIEW Aem 6 2 PRE INSTALLATION VEHICLE 7 3 O ITEM DE Cie ON r C 7 4 EOQUIPMENT LIST reen a a a a a A E E E 8 AL PARTA 070035 8 SRK PARTB 9 serrera ese ae
19. r to use the equipment more efficiently Even when relying on the function of the Leica Steer Ready Kit the driver is still responsible for observation of the machine and the surrounding area He should shut down or assume manual steering control in dangerous situations To shut down the Leica Steer Ready Kit turn off the power switch so that the light is off Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 7 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 4 Equipment List 4 1 SRK Part A 676035 Ape Description Part 2 Universal Bracket 676173 M6 x 60mm Bolt M6 Star Washer Qty Description Part 1 Steer Ready Controller 676171 E Qty Description Part 1 CAN Extension Cable 676030 Bie of Qty Description Part as mojoRTKSRKSO C Cabe 676591 Engage Switch 676191 Qty Description Part Qty Description Part 1 Wiring Harness SR Controller 676172 1 In Cab Wiring Harness 676186 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 9 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 10 4 2 SRK Part B 676038 676033 Override Cable 676178 Power Cable 676178 676033 Override Cable Part Qty Description Part Qty Descriptio
20. rior explicit approval of Leica Geosystems e Inadequate safeguards at the work site for example when using on the intended site e The Leica Steer Ready Kit is not suitable for applications on narrow dikes or on steep hillsides where danger of vehicle roll over exists 9 3 Environment N Danger 9 4 Manufacturer of the product Manufacturers of non Leica Geosystems accessories Adverse use can lead to injury malfunction and damage It is the task of the person responsible for the equipment to inform the user about hazards and how to counteract them The product 15 not to be operated until the user has been instructed on how to work with it Unauthorized modification of agricultural machine by mounting or installing the product may alter the function and safety of the machine Precautions Follow the instructions of the machine manufacturer If no appropriate instruction is available ask machine manufacturer for instructions before mounting or installing the product Limits of Use Suitable for use in an atmosphere appropriate for permanent human habitation not suitable for use in aggressive or explosive environments Local safety authorities and safety experts must be contacted before working in hazardous areas or in close proximity to electrical installations or similar situations by the person in charge of the product Responsibilities Leica Geosystems AG CH 9435 Heerbrugg hereinafter referred to as Leica Geosy
21. stallation of a Leica moJoRTK console is not included in this manual Please refer to your local dealer or the relevant manual for further details on this product The Leica Steer Ready Kit is suitable for all Case Magnum MX tractors which have been retrofitted with Trimble Autopilot valves Certain vehicle variations and non standard modifications may affect some cable lengths Extension cables may be required see your local Leica Dealer This installation manual will provide the necessary steps to successfully install the Leica Steer Ready Kit To ease the use of this manual please observe the following advice Relating to all pictures and schematics they are to be seen as reference only There may be slight deviations from the actual looks of the Leica Steer Ready Kit These deviations are caused by individual applications and have no impact on the function capabilities of the Leica Steer Ready Kit Leica Geosystems original spare parts are especially designed for the Leica Steer Ready Kit They live up to the high design standards for safety and reliability We advise you that components or parts not provided by Leica Geosystems for the Leica Steer Ready Kit should not be used because they might jeopardize the safety and function of the Leica Steer Ready Kit We therefore can not be responsible for such redesign or adaptations Any obstinate changes on our Leica Steer Ready Kit void the company warranty In addition conformity declaration or lo
22. stems is responsible for supplying the product including the user manual and original accessories in a completely safe condition The manufacturers of non Leica Geosystems accessories for the product are responsible for developing implementing and communicating safety concepts for their products and are also responsible for the effectiveness of those safety concepts in combination with the Leica Geosystems product Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 29 Person in charge of the product Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 30 e The person in charge of the product has the following duties understand the safety instructions of the product e To be familiar with local regulations relating to safety and accident prevention e To inform Leica Geosystems immediately if the product and the application becomes unsafe The person responsible for the product must ensure that it is used in accordance with the instructions This person is also accountable for the training and the deployment of personnel who use the product and for the safety of the equipment in use Unauthorized modification of machines by mounting the product may alter the function and safety of the machine Precautions Follow the instructions of the machine manufacturer If no appropriate instruction is available ask machine manufacturer for instructions before mounting the product Hazards of Use Only Leica Geosystems
23. ty to return any agricultural products purchased within Australia under our exclusive 8n8 Satisfaction Guarantee Program You will receive a full refund of your purchase price if you meet the following criteria The equipment must be returned and received in the Leica Geosystems Brisbane Qld office within 8 days of the invoice date The equipment must have no more than 8 hours of auto steer operating time on the system meter The equipment must be in as new condition and in original packaging If you are not satisfied for any reason you may return your new mojoRTK products no questions asked This is the Leica 8n8 Satisfaction Guarantee Warranty Leica Geosystems offers its Standard International Warranty which is 12 months for all agricultural product purchases and 90 days for battery products Please go to the website to review the warranty document Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 35 Original text Printed in Singapore 2009 Leica Geosystems Pty Ltd Brisbane Australia 676107 Version 1 2 0en Leica Geosystems Pty Ltd 270 Gladstone Road Dutton Park QLD 4102 eca Phone 61 7 3891 9772 when it has to be right www mojoRTK com Geosystems
24. uto steer engage switch up from under the console to the position that the switch will finally be placed Step 4 Connect the switch to the cable crimps as indicated in the diagrams to sight Numbers labeled on the crimps as well as the switch to assist in this step Black Step 5 Press the switch into the console so that the side that locks down when pressed is towards the back of the machine 24 7 6 Routing the Override Harness Step 1 Refer to Section 4 1 of the equipment list to ensure that you have the manual override cable Part No 676033 Step 2 The sensor to which the manual override cable is to be connected is located in the same area as the other hydraulic valves associated with the auto steer Step 3 Feed the manual override cable through the entry point into the vehicle s cab at the rear right side of the cab under the vehicle cab through to the left hand side of the vehicle at the front of the cab Step 4 Plug the manual override cable onto the sensor connector as shown Sensor Connector Step 5 Plug the other end of the manual override cable into the In Cab harness Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 25 Leica Steer Ready Kit for Case Magnum MX Trimble Autopilot 26 7 7 Routing the Power Cable Step 1 Refer to Section 4 1 of the equipment list to ensure that you have the correct power cable Part No 676178 Step 2 The vehicle s auxiliary power connector
Download Pdf Manuals
Related Search