Meat Grinder Instruction manual
Contents
1. Meat Grinder Instruction manual Model CD400 A Safety Tips Position on a flat stable surface A service agent qualified technician should carry out installation and any repairs if required Do not remove any components on this product DO NOT feed meat in to the appliance by hand ALWAYS use the pusher supplied DO NOT use fingers to clear the exit hole while the appliance is turned on DO NOT allow the motor to work against a blockage for any length of time DO NOT immerse in water DO NOT operate appliance with a damaged cord or plug DO NOT let cord hang over edge of table or counter DO NOT let cord contact hot surface including the stove Only use original Apuro parts and attachments with this appliance The use of attachments not recommended or sold by the manufacturer may cause fire electric shock or injury Unplug from outlet when not in use before putting on or taking off parts and before cleaning Always carry the appliance by the motor housing Not suitable for outdoor use Close supervision is necessary when the appliance is used by or near children Keep all packaging away from children Dispose of the packaging in accordance to the regulations of local authorities If the power cord is damaged it must be replaced by a Apuro agent or a recommended qualified technician in order to avoid a hazard Introduction Please take a few moments to carefully read through this manual Correct maintenance a2. e barrel cap is on too tight Loosen the cap appliance evenly The cutting plate is blocked Remove and clean the plate The cutting blade is blunt Replace the cutting blade Telephone Helpline 1 888 747 1447 Technical Specifications Model Voltage Power Output mia as Weight mm CD400 A 230V 50Hz 800W 250kg hour 444 x 270 x 506 24 5kg Compliance To help prevent possible harm to human health and or the environment the product must be disposed of in an approved and environmentally safe recycling process For further information on how to dispose of this product correctly contact the product supplier or the local authority responsible for waste disposal in your area Apuro parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international independent and federal authorities All rights reserved No part of these instructions may be produced or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Apuro Every effort is made to ensure all details are correct at the time of going to press however Apuro reserve the right to change specifications without notice DECLARATION OF CONFORMITY Equipment Type Model Legislation Standards Producer Name Producer Address Meat Mincer CD400 A C Tick AS NZ 3820 Essential Safety Requ
3. ieces to fit in to the hole in the hopper tray 2 Turn the power switch ON 3 Feed the meat into the shaft using the food pusher A WARNING Never push the meat into the shaft using your fingers If the circuit breaker stops the appliance or the appliance becomes jammed 1 Turn Off the appliance immediately 2 Press the RESET button located at the back of the appliance above the power cord 3 Turn and HOLD the switch in the reverse position to clear the blockage 4 Remove and clear the mincing barrel and all components Cautions e When carrying the unit hold the Motor Housing with both Hands not to hold only Plate e Be careful to carry the unit because it is very heavy e Do not grind hard food such as bones or nuts e Do not grind food with hard fiber e g ginger e The air passage at the bottom and the side of Motor Housing e To avoid jamming do not force to operate the unit with exessive pressure e Do not unplug the appliance by pulling the cord To unplug grasp the plug not the cord e Make sure that the voltage and frequency indicated on the rating plate are the same as your local supply and that the external earthed wire is reliable connected e The appliance should be used strictly in accordance with these instructions as no liability can be accepted for any damage caused by non compliance with these instructions or any other improper of handling Telephone Helpline 1 888 747 1447 Cleaning Care amp Main
4. irements for Low Voltage Electrical Equipment AS NZS CISPR 14 1 2010 AS NZS 60335 1 2002 IEC 60335 2 64 2000 Annex ZZ of AS NZS60335 1 2002 A3 Apuro 15 Badgally Road Campbelltown NSW 2560 I the undersigned hereby declare that the equipment specified above conforms to the above Legislation and Standard s Date Signature Full Name Position 22 11 12 1 lan Richard Cromwell Commercial Director CD400 A_v2
5. nd operation of this appliance will provide the best possible performance from your Apuro product Pack Contents The following is included Apuro Meat Grinder e Cutting screw Hopper tray e Cutting plate coarse 8mm Food pusher e Cutting plate medium 6mm Feed screw e Instruction Manual Apuro prides itself on quality and service ensuring that at the time of packaging the contents are supplied fully functional and free of damage Should you find any damage as a result of transit please contact your Apuro dealer immediately Telephone Helpline 1 888 747 1447 Assembly 1 Insert the mincing barrel into the motor housing mouth with the hole facing upwards Fig 1 2 Tighten the locking knob Fig 2 3 Insert the feed screw in to the mincing barrel Turn the screw slightly to slot the base of the screw on to the transmission shaft if necessary Fig 3 4 Insert the cutting blade on to the end of the feed screw Fig 4 N Note Ensure the flat face of the blade faces forwards as illustrated 5 Match the groove on the edge of the desired cutting disc to the pin on the mincing barrel Slide the cutting disc on to the feed screw Fig 5 6 Screw the barrel cap on to the end of the mincing barrel until tight Fig 6 7 Twist the hopper tray into place Fig 7 Operation A Note Clean the appliance with warm soapy water and dry thoroughly before using for the first time 1 Cut the meat into small enough p
6. tenance Note Always switch off and disconnect the appliance from the power supply before cleaning e Do not use any abrasive cleaning agents on the appliance Use warm soapy water e Do not immerse the motor housing in water Clean the exterior with a damp cloth e A Apuro agent or qualified technician should carry out repairs if required For ease of cleaning disassemble the appliance e Unscrew the barrel cap A Note If the cap has been put on too tight knock the corners of the cap with a rubber mallet or similar instrument to loosen it e Remove the mincing barrel plate blade and feed screw as one unit Gently tip the barrel to remove the pieces one by one e Twist off the hopper tray e Remove meat from all components and wash in warm soapy water e Always dry thoroughly after cleaning e Lubricate the parts with a little cooking oil before replacing for best performance Troubleshooting If your Apuro appliance develops a fault please check the following table before making a call to the Helpline Fault Probable Cause Action The appliance is not working The appliance is not switched Check the appliance is plugged in on correctly and switched on Plug and lead are damaged Call Apuro agent or qualified technician Fuse in the plug has blown Replace the plug fuse Power supply Check power supply Internal wiring fault Call Apuro agent or qualified technician Minced meat does not exit the Th
Download Pdf Manuals
Related Search