Home
MagniLink Vision
Contents
1. e Thechair should have a back rest e The seat of the chair should be at a height which does not make your legs become numb e Let your feet rest on the floor e The reading table should be at a height which allows your forearm to rest horizontally on the table e Shield off daylight Lights from ceiling lamps table lamps and windows might be reflected on the monitor User Manual 79 41 571c MagniLink Vision era 5 Instructions Three panels are available for MagniLink Vision The functions on each panel are listed below as well as the function of the reading table 5 1 3 Push 0 s As LED indicator Power on off Magnification buttons Colour Gray scale picture mode High contrast mode with artificial colours ee PO TS 5 2 5 Push AP Sp amp ss gn bod d 8 LED indicator Power on off Magnification buttons Colour Gray scale picture mode or Light adjustment High contrast mode with artificial colours Brightness control Autofocus on off or DVI switch Control for guiding line curtain E 2 12 User Manual 79 41 571c MagniLink Vision 5 3 2 Turn f ed Q 9 Power on off and LED indicator 10 Magnification control 11 Colour picture mode and high contrast mode 5 4 Reading table 12 Side way direction friction adjustment 13 Depth way direction friction adjustment User Manual 79 41 571c MagniLink Vision EN 5 5 Description of features 1 LED indica
2. Do not expose the system to sudden or extreme changes in temperature If you are unsure contact your dealer or service technician To prevent fire or shock hazard do not expose the equipment to moisture To reduce the risk of electric shock do not remove the cover No user serviceable parts inside Please refer service to qualified service personnel 8 User Manual 79 41 571c MagniLink Vision 3 Unpacking The equipment is delivered in one box containing e the unit e the user manual Inspect the package for exterior damage Note that severe damages should be addressed with the transport company Open the box and take out the MagniLink Vision Remove the packaging and place the unit on a table The mains cord is placed on the back of the unit Refer to the section Installation in the next chapter for further information 3 1 Packaging The packaging of the unit contains the following e cellular plastic EPP e corrugated cardboard e polyethylene LDPE4 LVI recommends that all packaging material be kept to be reused in case of future shipping User Manual 79 41 571c MagniLink Vision aa 4 Installation Place the unit on a table The MagniLink Vision should be placed at least 10 cm 3 9 inches from the edge of the table Note that the system s reading table can be moved up to 30 cm 11 8 inches in three directions MagniLink Vision is very light which means that it is important to place the system
3. correctly to ensure that it always remains stable especially if the reading table is in its most extended position An overload in this position may cause the system to turn over Connect the mains cord to the wall socket and press Power On The unit is now ready to be used The screen can be tilted 10 degrees and lowered 8 5 cm 3 4 inches from the highest position Place your hands on the soft touch padding on both sides of the screen and adjust it to the desired position Release the brakes on the reading table you are now ready to start using the MagniLink Vision Writing position Place the reading table in the desired position Lock the table by pushing the side way brake to the right end position and the depth way brake to the far end position towards the back Transport position Place the table in the middle position and push it back as far as possible Lock the table by pushing the side way brake to the right end position and the depth way brake towards the back End User Configuration EUC A configuration program is available which can individually modify the settings as per the user s requirements The settings are magnification max min guiding line colour thickness lighting settings and high contrast mode colours number of colours 10 User Manual 79 41 571c MagniLink Vision 4 1 Work place A comfortable work place around your MagniLink is important It could be useful to keep the following in mind
4. interference to radio communications However there is no guarantee that no interference will occur in a particular installation If this equipment causes harmful interference to radio or television receivers which can be determined by turning the equipment on and off the user is encouraged to try one or more of the following measures e Reorient or relocate the receiving antenna e Increase the distance between the equipment and receiver e Connect the equipment to a different circuit from the one that the receiver is connected to e Consult LVI or an experienced radio TV technician for help CAUTION The Federal Communications Commission warns the user that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment To comply with the FCC rules the system should only be used with the enclosed LVI power supply User Manual 79 41 571c MagniLink Vision Ea DECLARATION OF CONFORMITY according to the Medical Devices Directive 93 42 EEC with amendments from directive 2007 47 EC Type of equipment Reading Aid Brand name or trademark MagniLink Type designation MLV Product class Class 7 Manufacturer LVI Low Vision International AB Address Verkstadsgatan 5 S 352 46 V xj Sweden Web http www lvi se Phone 46 470 727700 Fax 46 470 72 77 25 As the manufacturer we declare under our sole responsibility
5. User Manual MagniLink Vision LVI Low Vision International Verkstadsgatan 5 Tel 46 470 727700 E mail info lvi se 352 46 Vaxjo Fax 46 470 727725 Internet www lvi se User Manual 79 41 571c MagniLink Vision LIST OF CONTENTS 1 GENERAL INFORMATION sucia 5 23 SAFETY INFORMATION crea 7 Bx UNPACKING oreen eiee es ea eas a eee et 9 o RENAR o a E aulal aba 9 4 INSTALLA HON ct ee A AS ES 10 Al Work paee A O SAS Abe Ne ARLA 11 Bo INSTRUCTIONS iS so aba 12 A O Re at et rela ae 12 O weer SS yur een TE De a 12 JO 2 TUL O A 13 RES aleta rea 13 5 5 Description ore aurea into 14 6 TROUBLESHOOTING css loas 18 7 TECHNICAL SPECIFICATION sra di cdas 19 8 FCC STATEMENT USA AND CANADA ONLY eee 21 User Manual 79 41 571c MagniLink Vision EN The information in this manual has been carefully checked and is believed to be accurate However LVI assumes no responsibility for any inaccuracies which may be contained in this manual In Under no circumstances will LVI be liable for direct indirect special exemplary incidental or consequential damages resulting from any defect or omission in this manual In the interest of continued product development LVI reserves the right to make improvements to this manual and the products it describes at any time without notice or obligation ARN User Manual 79 41 571c MagniLink Vision 1 General Information MagniLink Vision MLV is a video magnifier which is ava
6. at this product should not be treated as household waste when you wish to dispose of it Instead it should be handed over to an applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences to the environment and human health which could otherwise be caused by inappropriate disposal of this product The recycling of materials will help to conserve natural resources For more detailed information about the recycling of this product please contact your local city office household waste disposal service or the retail store where you purchased this product 20 User Manual 79 41 571c MagniLink Vision 8 FCC statement USA and Canada only NOTE This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept interference received including interference which may cause undesired operation This equipment has been tested and complies with the limits for a Class B digital device according to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy If not installed and used in accordance with the instructions it may cause harmful
7. ct an authorised service technician Never disassemble any covers to try to repair the system yourself 18 User Manual 79 41 571c MagniLink Vision 7 Technical specification MagniLink Vision with an 18 5 TFT widescreen Magnification 2 5 50x HR or 1 7 60x HD Resolution 1366 x 768 Power consumption Max 35 W HR or 44 W HD Power consumption standby 0 8 W Weight 11 8 kg MagniLink Vision with a 23 TFT widescreen Magnification 3 0 50x HR or 2 0 60x HD Resolution 1920 x 1080 Power consumption Max 52 W HR or 59 W HD Power consumption standby 0 8 W Weight 13 5 kg General properties Refresh rate 60 Hz Luminance 300 cd m Contrast 1000 1 Focusing distance 0 60 mm at max magnification Working space 110 mm 195 mm Lamp type 4 LEDs Hk or 8 LEDs HD Mains Voltage 100 240 V 50 60 Hz Size of reading table 420 x 300 mm W x D Dimensions in use 420 x 470 x 570 mm W x Dx H Dimensions of packaging 620 x 590 x 610 mm W x Dx H Temperature limit Transportation and storage 20 C 60 C Operation 5 C 35 C Relative air humidity lt 80 Accessories DVI switch PC software User Manual 79 41 571c MagniLink Vision SEN Disposal of old Electrical amp Electronic Equipment Applicable throughout the European Union and other European man countries with separate collection programs This symbol found on your product or on its packaging indicates th
8. gh contrast mode with artificial colours Press the button to switch between different combinations of colours Colour combinations available in the standard configuration Background Text Background Text White Black Red Black Black White Black Red Yellow Black Yellow Blue Black Yellow Blue Yellow Green Black White Blue Black Green Blue White The colour settings in high contrast mode can be adjusted with the EUC software please contact your dealer for more information 6 Brightness control By pressing the buttons it is possible to adjust brightness Press up to increase and down to decrease the brightness When button picture mode 4 is pressed the lamps intensity is adjusted instead In this way the best conditions for reading in different situations can be achieved 7 Autofocus on off Pressing the button locks the autofocus in the present position This could be used for example when writing by hand without risk of disturbing the focusing system with the hand or the pen A subsequent press of the button reactivates the autofocus system DVI switch 5 Push panel only When the DVI switch is connected press the button for three seconds to switch between the camera image and the computer image on the built in screen User Manual 79 41 571c MagniLink Vision SEN 8 Control for guiding line curtain Controls either the position of the guiding line or the size of the curtain Press the right button to move the guiding line d
9. ilable in several models All models have the same structure reading table and electronics Thereafter the module is chosen following 3 steps Camera available as High Resolution HR or High Definition HD Screen size integrated 18 5 or 23 wide screen TFT Panel equipped either with push buttons or turn knobs which control different features User Manual 79 41 571c MagniLink Vision NN Model Camera Screen Control panel MLV 01 HR 18 5 3 Push MLV 02 HR 18 5 2 Turn MLV 03 HR 18 5 5 Push MLV 04 HR 23 0 3 Push MLV 05 HR 23 0 2 Turn MLV 06 HR 23 0 5 Push MLV 07 HD 18 5 3 Push MLV 08 HD 18 5 2 Turn MLV 09 HD 18 5 5 Push MLV 10 HD 23 0 3 Push MLV 11 HD 23 0 2 Turn MLV 12 HD 23 0 5 Push The equipment complies with requirements for CE approval of medical devices according to 93 42 EEG directives and MDD 93 42 ECC with amendment from directive 2007 47 EC ra User Manual 79 41 571c MagniLink Vision 2 Safety Information MagniLink Vision is only intended for use as a reading aid in home school or office environments e Before connecting check the system and the mains cord to ensure that nothing is damaged The enclosed power supply is only intended for use with the MagniLink Vision e Never operate the MagniLink Vision if the unit has been exposed to water or other liquids or other liquids e Damaged mains cord or plugs may result in electrical shock or a fi
10. ownwards Continue to press the button and the guiding line switches from horizontal to vertical position and the guiding line will be moved from left to right Further pressing the button and the guiding line turns into a horizontal curtain that reduces the visual area Continue to press the button and the curtain becomes vertical The left button gives the opposite result The colour and size of the guiding line can be adjusted with the EUC software It is also possible to select if the guiding line the curtain or both should be active please contact your dealer for more information 9 Power on off and LED indicator Press the button to switch the unit on or off Green light indicates that the unit is on Flashing green light indicates start up Slowly flashing yellow light indicates that the unit is in standby mode Red light indicates an error refer to the Troubleshooting section 10 Magnification control To decrease the magnification turn the knob to the left minus and to increase the magnification turn the knob to the right plus The magnification settings can be adjusted with the EUC software please contact your dealer for more information 11 Colour picture mode and high contrast mode With the knob in the upright starting position the colour picture with natural colours is displayed on the screen Turn the knob to the left for a negative high contrast mode and to the right for a positive high contrast mode The
11. re are four combinations in the standard configuration Background Text Background Text White Black Yellow Black Black White Black Yellow The colour settings in high contrast mode can be adjusted with the EUC software please contact your dealer for more information 16 User Manual 79 41 571c MagniLink Vision 12 Side way direction friction adjustment Set the side way friction by moving this handle With the brake in the left end position the reading table is unlocked To increase friction push the side way brake to the right 13 Depth way direction friction adjustment Set the depth way friction by moving this handle With the brake in the near end position the reading table is unlocked To increase friction push the depth way brake towards the back User Manual 79 41 571c MagniLink Vision a 6 Troubleshooting If nothing happens when turning the system on refer to the section Installation and check that all connections are correct If the LED to the left of the main switch is solid red something is wrong with the equipment and it cannot be used Press the main switch once and MagniLink Vision will make three attempts to restart If the light still indicates a solid red turn off the equipment and contact an authorised service technician If the light is flashing red it means that the wrong voltage is being supplied from the power supply If the problem continues pull out the power outlet cable and conta
12. re hazard Do not allow anything to rest or roll over the mains cord e If cleaning is required unplug the MagniLink Vision and then use a slightly damp not wet cloth Only use water or a detergent specially made for cleaning monitors and computers Do not use aerosol cleaners directly on the MagniLink Vision since it may overspray and cause an electrical shock e When operating the reading table do not place hands under or behind the reading table as one s finger may get caught between the reading table and the stand or the slides The MagniLink Vision should be placed at least 10 cm from the edge of the table Warning Do not apply excessive weight to the reading table when it is in its most extended position as this may cause the system to turn over which could lead to personal injuries e If the MagniLink Vision is to be transported do not lift the unit by the screen or the reading table as these are movable parts e If you are unable to restore normal operation by following the operating instructions do not attempt any further adjustments Unplug the set and contact your dealer or service technician Only use replacement parts specified by LVI User Manual 79 41 571c MagniLink Vision Ea e Moving the system from a cold to a warm place may cause condensation water droplets on its internal surfaces or on the lens To avoid condensation install the system in the room where it is to be used at least 30 minutes before use
13. that the product complies with the provisions of the Council Directive 93 42 EEC with amendments from directive 2007 47 EC we will keep the technical documentation described in section 3 of Annex VII available to the national authorities for a period ending at least five years after the last product has been manufactured the device meets the Essential Requirements of Annex 1 which applies to it taking into account the intended purpose of the device to follow the requirements regarding products placed on the market as described in section 4 of Annex VII IX Manufacturer _ Manufacturer s authorized representative Date Signature Position PHOT ct fanns ban Quiles e 2 Managing Director Clarification Erik Bondemark ES User Manual 79 41 571c MagniLink Vision
14. tor Green light indicates that the unit is on Flashing green light indicates start up Slowly flashing yellow light indicates that the unit is in standby mode Red light indicates an error refer to the section Troubleshooting 2 Power on off Press the button to switch the unit on or off 3 Magnification buttons To decrease the magnification press the lower button minus and to increase the magnification press the upper button plus 4 Colour Gray scale picture mode Press button for a picture mode with natural colours or gray scale picture Light Adjustment 5 Push panel only Press and hold the button to temporarily adjust the light by pressing brightness control 6 up or down This could be used for example by light sensitive persons or when reading on glossy paper The system will automatically switch between ROPC Reading Optimized Picture Control and DPC Dynamic Picture Control when the light reaches a certain level There is no switching between natural colours and gray scale when the light adjustments are used Light on off The light can be turned on and off by pressing the button for three seconds The system will automatically switch between ROPC Reading Optimized Picture Control and DPC Dynamic Picture Control The light settings and grey scale settings can be adjusted with the EUC software please contact your dealer for more information 14 User Manual 79 41 571c MagniLink Vision 5 Hi
Download Pdf Manuals
Related Search
Related Contents
SISTEMA DE VIGILANCIA INALAMBRICO A COLOR FNC-0500TX 5 Port 10/100Mbps NWay Switch Card User's Guide Intel PX875P User's Manual Life Fitness 95R User's Manual Ver/Bajar TAKS Analyzer Setup and User Manual 0.07.A.0018 SECTOR installation manual 16Aug2012 ER-19F WADE-8041 User`s Manual Copyright © All rights reserved.
Failed to retrieve file