HUSKY 2-YEAR LIMITED WARRANTY PROGRAM
Contents
1. HSK142 Man 071405 7 20 05 4 16 PM Page 6 HUSKY 2 YEAR LIMITED WARRANTY PROGRAM The Home Depot warrants this Husky Power Product to the original user to be free from defects in materials and workmanship for a period of two years from the date of purchase If you believe that this unit is defective during its original two year warranty period return the unit with proper proof of purchase to the Hore Depot store or you may send the product to Husky Power Products at the address below This Husky Power Product is warranted to the original purchaser only to be free of defects in materials and workmanship for two years from the date of purchase without additional charge The warranty does not extend to subsequent purchasers or users Husky Power Products will not be responsible for any amount of damage in excess of the retail purchase price of the product under any circumstances Incidental and consequential damages are specifically excluded from coverage under this warranty This product is not intended for conmrrercial use This warranty does not apply to accessories or damage to units from misuse or incorrect installation Misuse includes wiring or connecting to improper polarity power sources RETURN REPAIR POLICY Defective products other than accessories may be returned postage prepaid to Husky Power Products Any defective product other than accessories that is returned to Husky Power Products within 30 days of the date of purchase w2. 4 AC CHARGING Make sure the AC source is 120 volts 60 Hz a simple wall receptacle is 120 volts The worklight can be operated by its own stored power or with the coiled cord plugged to a DC power source DO NOT OPERATE WORKLIGHT WHILE CHARGING 1 Uftthe rubber plug from the charge port 6 on the worklight base 2 Connect the AC charger adapter to the recharge port 3 Connect the AC charger adapter to an AC power source or household wall receptacle 4 Charge for 25 30 hours Red LED will light to indicate charging and will flash to indicate a full charge 5 After charging disconnect the AC charger adapter from the power source and the charge port and store the adapter 6 Replace the rubber plug in the charge port to keep out dust and moisture 2 An additional benefit of the worklight is the utility value of the clamp and hook accessory shown in Figure 5 Utlizing this accessory provides many mounting positioning options that will allow handsfree operation The most simple way to remove the lamp from the base 1 Holding the lamp head 1 in place rotate the base 3 of the unit counter clockwise 2 Separate the Threaded Bolt 4 from the Threaded Bolt Hole 5 NOTE The Thurb Screw assembly 2 may be removed but is not recommended Attach the clamp and hook assembly to the lamp head 1 as follows 1 Loosen the Clamp Thumb Screw 5 and remove the Clamp N ut 6 2 Align the Clamp Thunb Screw 5 of t
3. EXPERIENCE A PROBLEM WITH YOUR HUSKY PRODUCT CALL TOLL FREE 800 916 7004 IN MOST CASES A HUSKY SERVICE REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE KEY INFORMATION YOU SHOULD KNOW OPERATE SIMPLE TWO POSITION PUSHBUTTON p ne CLAMP HOOK ASSEMBLY INCLUDED AC AND DC CHARGER ADAPTERS INCLUDED WORKLIGHT CAN ALSO BE USED AS A DC POWER SOURCE USER S MANUAL AND WARRANTY INFORMATION THIS MANUAL CONTAINS IMPORIANT INFORMATION REGARDING SAFETY OPERATION MAINTENANCE AND STORAGE OF THIS PRODUCT READ CAREFULLY BEFORE USE AND RETAIN FOR FUTURE REFERENCE 4140 S W 30th Ave Ft Lauderdale FL 33312 Toll Free 800 916 7004 HSK142 Man 071405 7 20 05 4 16 PM Page ii Dp THS UNT IS SHPPEDIN A PARTIALLY CHARGED SIAIE UPON REPT Ee IMMEDIATELY CHARGE THE BATTERY FOR 25 30 HOURS USING THE SUPPLIED Congratulations on purchasing the Husky Rechargeable Worklight The AC CHARGRR RECHARGE AFTER EXCH USE worklight includes a clamp and hook making it easy to position the worklight for hands free operation IMPORTANT SAFETY INFORMATION PLEASE READ INSTRUCTION MANUAL COMPLETELY FOR ALL SAFETY AND WARNING INSTRUCTIONS The rechargeable non spillable sealed 12 volt lead acid battery will provide years of dependable use recharge after recharge The HSK142 worklightis a versatile practical and a perfect choice for travel camping picnicking tailgate parties and boating WARNINGS The worklight
4. he clamp and hook assembly with the Threaded Bolt Hole 3 of the lamp head and tighten well JOUL JOUL JUUUUBULL Figure 4 Lamp Assembly Figure 5 Clamp and Hook Assembly 1 Lamp Head 2 Lamp Thumb Screw 3 Threaded Bolt Hole 4 Clamp and Hook Assembly 5 Clamp Thumb Screw 6 Clamp Nut 1 Lamp Head 2 Thumb Screw Assembly 3 Lamp Base 4 Threaded Bolt 5 Threaded Bolt Hole HSK142 Man 071405 7 20 05 4 16 PM Page 4 Dp 5 DC CHARGING WARNING Use ONLY the supplied DC charge CORD do not substitute DC charge requires the use of the supplied DC adapter 1 Connect the barrel connector of the DC charge cord to the worklights DC receptacle 4 and the other end to a 12 volt DC source such as your automobile s 12 volt accessory receptacle 2 Recharge for 3 hours maximum Do not overcharge There is no indicator to show full charge 3 After charge disconnect cord and wait 5 minutes before use 6 FUSE REPLACEMENT The worklight is equipped with a coiled cord with a 5 amp fuse If this fuse blows there may be a short circuit in the power cord or lamp assembly The fuse will blow if the 1 Retaining Screw battery is connected with reverse polarity 2 Bulb Assembly Check the fuse with an ohmmeter or other continuity checker If the fuse is blown 3 Retaining wire l Figure 6 Bulb Assembly A peice investigate why the fuse blew and correct the proble
5. ill be replaced free of charge If such a product is returned more than 30 days but less than two years from the purchase date Husky Power Products will repair the unit or at its option replace it free of charge If the unit is repaired new or reconditioned replacement parts may be used at Husky Power Product s option A unit may be replaced with a new or reconditioned unit of the same or comparable design The repaired or replaced unit will then be warranted under the terms of the remainder of the warranty period The custorrer is responsible for the shipping charges on all returned items after 30 days During the warranty period Husky Power Products will be responsible for the return shipping charges UMITATIONS This warranty does not cover accessories bulbs fuses and batteries defects resulting from normal wear and tear including chips scratches abrasions discoloration or fading due to usage or exposure to sunlight accidents damage during shipping to our service facility alterations unauthorized use or repair neglect misuse abuse failure to follow instructions for care and maintenance fire flood and Acts of God If your problem is not covered by this warranty call our Technical Support Department at 954 5844446 or toll free at 800 916 7004 for general repair information and charges if applicable STATE LAW RIGHTS This warranty gives you specific legal rights Sore states do not allow linitations on how long an implied
6. includes one AC charger adapter and one 12 volt DC charger for recharge flexibility for use around horre business or in the field 12 volt DC power is e NEVER operate the worklight during AC or DC charging available from most vehicles boats jump starters and portable battery packs e The worklight contains a non spillable sealed lead acid battery and must be recycled or disposed of properly Any disposal questions call toll free 2 FEATURES 877 288 7722 e DO NOT expose worklight to fire or intense heat as this may result in an explosion Cored OV NESS Ana Rechargeable for portability e DO NOT open battery compartment or short circuit as this may cause the battery to Powerful 25 wait quartz halogen bulb leak or get hot causing personal injury e Clamp and hook adapter for versatile mounting options e USE ONLY THE CHARGERS PROVIDED WITH UNIT e The worklight also functions as a 12 volt DC portable power supply e AFTER CHARGE disconnect and wait 5 minutes before use e Worklight head swivels and tilts for exact light placement e DO NOT OVERCHARGE AC charge 25 30 hours maximum f f t th klight DC Charge 23 hots Rubber safety guard bezel and plastic cage protect the worklig D e Toggle power switch ON OFF CAUTIONS 1 Do not substitute power cords or adapters Do not use extension cords ONLY recharge with supplied AC and DC charge adapters 2 Do not subrrerge in water This unit is not waterproof it is weather
7. m before replacing the fuse The i fuse is accessed by unscrewing counterclockwise the tip of the large DC plug Ensure the san type and value fuse is used as replacement 7 BULB REPLACEMENT SPECIACATIONS NOTE W hen handling a new halogen bulb use a clean tissue do not touch the glass Battery 2 eee eee 12 Volt 3 Amp Hour Sealed LeadAcid portion of the bulb Natural oils from your hands can cause the bulb to fail If 12 Volt Power Outlet with 10 12 Amp Automatic Breaker ae necessary clean the bulb with alcohol or a liquid window cleaner AC Adapter Charging Time 25 30 Hours Charging Indicator LED will For bulb replacement you will need a small Phillips screwdriver 2 flash to indicate full charge 1 Disconnect the worklight from any charging power source 2 Remove the rubber bezel by pulling it away from the lamp lens AC Charging Adapter 12 volt 300m 3 Remove the four Phillipsthead screws that secure the lens guard to the worklight DC Charging Cord 2 Male End Plug poy Coiled Cord lt lt 4 26 lt 4 aa 6 Feet with 5 Amp Fused Plug 4 Carefully separate the lens guard glass and rubber gasket DC Charging Time From Vehicle Approximately 2 3 Hours No Full Charge 5 Carefully lift the reflector and bulb assembly out of the housing See Figure 6 aes 6 Unsnap the retaining wire from the reflector s flange by pinching the two ends together and lifting BUID 226 6 ta tarpa fa G
8. os oh ee es 12 volt 25 watt quartz halogen 7 Loosen the Phillipshead retaining screw to remove the bulb assembly from the Beam Discharge time reflector There is no need to completely remove this screw 8 Slightly turn and lift out the bulb assembly from the back of the reflector 9 Disconnect the bulb assembly white wire from the power wire by separating the male spade terminal from the female terminal bra oot a Bd Approximately 40 Minutes 10 Insert the replacement H3 25 watt 12 volt halogen bulb assembly into the reflector flange 11 Reverse the proceeding procedure to reassemble the worklight Replacement worklight bulb assemblies are available from an electrical supply house You may also call Husky Power Products toll free 800 916 7004
9. resistant 3 Do not operate worklight while recharging This will prevent battery recharge and overheat the charging adapters 4 Worklight lens gets very hot when ON Do not touch lens keep children away from worklight This is nota toy 5 Keep worklight from flammable material extreme heat can cause fire 6 Keep sharp objects away from breakable lens 7 Do not drop or throw worklight it contains glass and a sealed lead acid battery 8 Do not crush cut pull or expose accessory cords to extreme heat Figure 1 AC Charger Adapter Figure 2 DC Charger Adapter 9 Position recharge cords away from sharp edges so they do not becore a safety hazard by becoming entangled HSK142 Man 071405 7 20 05 4 16 PM Page 2 3 OPERATION N ever operate the worklight during charging A two position ON OFF toggle switch controls the operation of the worklight The worklight can be continuously lit for up to 40 minutes on a full battery charge The worklight head swivels 180 degrees up and down to accommodate most any lighting situation To release the swivel head froma locked position simply rotate the thumbscrew counter clockwise to loosen Then position the swivel head in the desired position and tighten the thumbscrew to hold in place DC power socket Adjustable thumb screw for positioning ON OFF toggle switch DC receptacle cord Recharge LED indicator Charge port Ou AUNE Figure 3 Location Diagram
10. warranty lasts or the exclusion or linitation of incidental or consequental damages so the exclusions or limitations stated herein may not apply This warranty gives the purchaser specific legal rights other rights which vary from state to state may apply TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT Contact Husky Power Products Technical Support by telephone or mail We suggest that you keep the original packaging in case you need to ship the unit W hen returning a product include your name address phone number dated sales receipt or copy and a description of the reason for return and product serial number After repairing or replacing the unit we will make every effort to return it to you within four weeks WARRANTY ACTIVATION Please complete Warranty Activation Card and mail to Husky Power Products Enter HSK142 as Model and Husky Rechargeable Worklight as Product Type All Husky Power Product products must be registered within 30 days of purchase to activate this warranty Mail the completed registration form along with a copy of the original sales receipt to ATN GUSTOMER SERVICE HUSKY POMER PRODUCTS 4140 9V 30th Ave Ft Larbie FL33312 TOL FREE 800 916 7004 VARRANTY IS NON TRANSFERABLE AND NON REFUNDABLE lt HUSKY The Toughest Name In Tools BD071405 2005 VECTOR MAN UFACTURN G MADE IN CHINA 6 HSK142 HUSKY The Toughest Name In Tools 2 RECHARGEABLE WORKLIGHT IF YOU SHOULD
Download Pdf Manuals
Related Search