Fortress Security S02 User Manual v1.2.1
Contents
1. 1 Disarm Disarm the system 2 Away Arm Out Arm the system when all are outside the protected area 3 Home Arm Arm the system when anyone is inside the protected area 4 Panic Immediately set off sirens and phone calls even if the system is not armed www FortressSecurityStore com Slow Start Introduction This section covers the setup start use and programming of your Fortress Security Store SO2 alarm system in detail If you are ready to get started with your system use the Quick Start section and refer to this section as a resource when needed ATTENTION Your S02 series alarm system is preprogrammed except for those items detailed in Step 4 7 of the Quick Start section If you get additional sensors motion detectors smoke alarms etc please follow the instructions for installing those DO NOT re program the Main Panel or return it to the factory default without first consulting Fortress Security Store 2014 Fortress Security Store S02 v1 2 1 Page 35 www FortressSecurityStore com Slow Start Unpack Setup amp Install Your S02 System Step 1 Check the contents of the Fortress Security Store System box Packing List Components S02A 502B S02C 502D S02E 502F ee i Main Panels 1 1 1 1 1 1 Motion Detectors 2 3 0 3 3 4 Pet Motion Detectors 0 0 0 0 0 Panic Buttons 1 1 1 1 1 1 Door Window Sensors 5 10 10 10 10 10 Key Fob Remotes 2 3 3 3 3 3 Sirens 1 1 1 1 1 1 Outdoor Sirens 0 1 0 1 1 12. 1 LED is on when either the battery or wall power is present 2 LED is on when a sensor or detector is triggered 3 LCD gives zone number for triggered alarm and visual feedback during programming 4 LED is on when Away Armed unoccupied 5 LED is on when Home Armed occupied Tactile Keypad Action amp Programming Buttons 1 amp 2 These keys are not used 3 Escape back button for canceling actions or returning to normal status 4 amp 5 Different functions according to what action is being performed See rest of manual for actual usage The is called star or asterisk The key is called pound 6 Arms the system for unoccupied premises Away Arm 7 Arms the system for occupied premises Home Arm 8 Disarms the system 9 Panic Button Triggers an alarm even if the system is disarmed 10 Keypad used in programming and using the system Back and Side of Main Panel Fortress Security Store S02 DBUS Bar and Connections Physical connections such as wired sensors are connected here This is an advanced application for the S02 and should be considered only after determining that wired sensors are needed and that you have a basic understanding of electrical connections Main Panel Physical Connections 1 Main Panel On Off Switch Off turns off power from both wall jack and battery 2 Siren or other speaker 3 Line to an external telephone 4 Line from a telephone wall jack 5 Not a physica
3. Extreme pressure will shorten the life of the keypad and alarm 2014 Fortress Security Store S02 v1 2 1 Page 6 www FortressSecurityStore com Conventions When discussing programming registering or other events that require using the keypad the following conventions are used PASSWORD 4 digit password default is 1234 ZONE 2 digit zone 01 32 in most cases this is the sensor number NNN NNN NNNN Telephone number can be more or less than 10 digits if needed XX 2 digit setting could be minutes ring count or any variable 0 9 keys on the Main Panel keypad out home disarm return function keys on the Main Panel Note To enter programming mode pressing the Program button or pressing are equivalent commands This manual will use to represent pressing the Program button The terms programming and registering are used in this manual Programming uses the keypad to enter information in the Main Panel to change how the alarm system as a whole operates Registering or registration connects sensors detectors remotes and sirens to the Main Panel Once a device is registered the Main Panel communicates with it as a part of the alarm system 2014 Fortress Security Store S02 v1 2 1 Page 7 www FortressSecurityStore com Description of the Alarm System Major features e Tactile keypad with physical and audible feedback e LCD display panel which shows triggered zone e All functions available from the Main P
4. an alarm trigger to record a message to be sent when the automatic dialer calls the numbers in the notification phone list Anyone who answers will hear the message 5 Optional Program the External Siren The external siren is a penetrating noise maker that extends the distance an alarm is heard It requires an external power source 110 220 volts typical household voltage and it ships with its own power cable It communicates wirelessly with the Main Panel It has an additional wire attached which is the antenna The antenna allows the siren to work further away from the Main Panel Before actually mounting it make sure it can communicate with the Main Panel by programming it and or testing it according to the video Outdoor Alarm If you do not have access to the video use the directions in Outdoor Sirens 2014 Fortress Security Store S02 v1 2 1 Page 41 www FortressSecurityStore com Slow Start Use the S02 System Step 1 Learn about Features and Applications of the S02 System There are several features of the S02 system that may not be apparent at first This section explains those features and how you might use them including the information for programming them The conventions for using this section are PASSWORD 4 digit password default is 1234 ZONE 2 digit zone 01 32 in most cases this is the sensor number NNN NNN NNNN Telephone number can be more or less than 10 digits if needed XX 2 digit setting
5. Alarm is the best source for registering the siren with the Main Panel If it is not available read through these steps and then perform them Although it appears there are many steps and the process is difficult it is actually easy to perform if you read through the steps carefully 1 Ensure Main Panel is powered and press Disarm open lock symbol on a remote control 2 Unplug the Main Panel s attached siren to avoid noise 3 Press the Alarm button speaker icon on the remote control The Main Panel LCD display shows the remote control s zone and the alarm LED is on 4 Power on the remote siren The siren will make a two toned chirp then beep twice after a couple of seconds The siren is now powered up correctly 5 Disconnect the siren power cable wait 1 second then reconnect it The siren emits one beep Disconnect the siren power cable wait 1 second then reconnect it The siren emits one beep Disconnect the siren power cable wait 1 second then reconnect it The siren emits three beeps 6 Press the Disarm open lock symbol on the remote The remote siren emits two beeps 7 Immediately disconnect the siren s power cable for 3 seconds then reconnect 2014 Fortress Security Store S02 v1 2 1 Page 61 www FortressSecurityStore com The remote siren emits two beeps 2014 Fortress Security Store S02 v1 2 1 Page 62 www FortressSecurityStore com Pet Immune Motion Detectors Registering a Pet Immune motion detector is much like a regular
6. could be minutes ring count or any variable 0 9 keys on the Main Panel keypad out home disarm return function keys on the Main Panel Note Some commands work just on Zones 01 08 Later in this section an example shows how to move a sensor into Zones 01 08 if necessary Additional information about these features may be found in the appendices 2014 Fortress Security Store S02 v1 2 1 Page 42 www FortressSecurityStore com Step 2 Definition of Key Terms such as Zones Sensors Detectors Alarms Triggers Physically the S02 system consists of the Main Panel and a variety of peripherals sensors detectors sirens controllers panic buttons etc The primary classification of peripherals are sensors detectors mounted on surfaces to protect detect physical events controllers key fobs phones Main Panel that affect the system s state alarms sirens flashing lights Main Panel visual aural displays telephone notifications Basically the class sensors detectors detect something and trigger or cause an alarm So for example a glass break device detects broken glass and causes multiple alarms zone number on Main Panel display and lit LED sirens telephone notifications This detect gt trigger gt alarm sequence defines an alarm system The Fortress Security Store SO2 uses the concept of Zones to organize the detection part of the system You can think of a zone as a bucket of defense
7. in the Main Panel It identifies the wireless location of devices how they should work and when they should work The S02 has 32 wireless and 7 wired zones available Zones 01 08 of the wireless zones are special in that they can be programmed with more functionality than 9 32 Ignore the wired zones for now When programming the Main Panel you are actually setting up the zones then adding the devices to the zone by activating them while that zone is being programmed You will see how this is done in the 2014 Fortress Security Store S02 v1 2 1 Page 43 www FortressSecurityStore com programming examples Note To enter programming mode pressing the Program button or pressing are equivalent commands This manual will use to represent pressing the Program button By default all the devices that ship with the system are in a different zone When an alarm is triggered the Main Panel shows the zone number and that number also refers to a single device A device cannot belong to more than one zone at a time however a zone CAN have multiple devices assigned to it This is desirable if for example your location needs 50 sensors There are only 32 zones so something has to give One solution is to group the devices in a single room into a zone So Zone 11 for example may have 6 window sensors If the alarm is triggered the display still shows Zone 11 just not which of 6 sensors caused it Keep in mind how zones work as you read fur
8. is switched off 2014 Fortress Security Store S02 v1 2 1 Page 22 www FortressSecurityStore com 3 If the Main Panel will be wall mounted rather than have it sitting on a flat surface mount it now but do not make the final attachment Keeping it unattached for now allows moving around with it while installing and testing devices Note If the Main Panel can be installed so it is removable it will make maintenance and sensor checks easier later on 2014 Fortress Security Store S02 v1 2 1 Page 23 www FortressSecurityStore com Step 4 Change Your Password and Program Essential Information in the Main Panel Sensors motion detectors etc are already programmed but the Main Panel must have certain information programmed for a specific home or small business This and the next three steps perform the initial programming needed to 1 Change your password 2 Program at least one phone number into the system 3 Optional Record a message to be sent to the telephone numbers entered for notification 4 Mount the indoor siren and temporarily plug the siren into the Main Panel 1 Change your password A Think of a 4 digit number passworp you can remember easily B Change the default password to PASSWORD 1 Enter the old password 1234 Main Panel emits two beeps Out and Home LEDs turn on 2014 Fortress Security Store S02 v1 2 1 Page 24 www FortressSecurityStore com 2 Enter 10 passworp A small L appears in the second d
9. motion detector except that the Pet Immune detector has a code switch You will need a paper clip or ball point pen tip to depress the code switch and register the device PASSWORD 2 beeps out and home LEDs on 7 zone zone between 01 08 Turn on the detector s switch Located on top of unit next to Code button Depress the Code switch Detector s LED blinks rapidly then stops Release the Code Switch Detector s LED quits blinking Depress the Code switch 2 beeps RETURN RETURN 2 beeps out and home LEDs off Since you will want this device to only be active in Away Alarm mode change it s zone settings PASSWORD 2 beeps out and home LEDs on zone2 5 2 beeps X is 5 Away Armed Zone RETURN OF RETURN RETURN 2 beeps out and home LEDs off 2014 Fortress Security Store S02 v1 2 1 Page 63 www FortressSecurityStore com Appendices Appendix A Command Summary Appendix B System Maintenance Appendix C Technical Information Selected System Components 2014 Fortress Security Store S02 v1 2 1 Page 64 www FortressSecurityStore com Appendix A Command Summary Action Command Notes Change password 10 PASSWORD Default password is 1234 All sensors and detectors are Away Arm the system OUT mode Press out key until beep armed Home Arm the system HOME mode Press home key till beep All sensors and detectors except motion detectors are armed 2014 Fortress Securit
10. should be mounted on the same side as the LEDs on the transmitter A To test the detector arm the system Away or Home Arm by pressing the Out key for two seconds 1 When the alarm is ready immediately for Home 30 seconds for Away separate the two objects until the wireless transmitter s LED turns on The alarm LED will turn red The zone number will appear in the display Main Panel will emit a click 2014 Fortress Security Store S02 v1 2 1 Page 32 www FortressSecurityStore com 3 Optional Install the outdoor siren close to an electrical outlet so that the power cord will reach Before actually mounting it make sure it can communicate with the Main Panel by programming it or testing it according to the video Outside Alarm If programming it for the first time without access to the video see the section Outdoor Sirens which details the steps for programming A To test the detector without programming testing connect the siren Siren emits a two toned chirp Approximately 5 15 seconds later the siren emits two beeps 1 Press the Panic Button on a key fob see next section or the Emergency key on the Main Panel The siren sounds The Alarm LED turns red The zone number appears in the LCD display Main Panel will emit a click 2014 Fortress Security Store S02 v1 2 1 Page 33 Step 8 Learn and Use the key fob for Remote Control The key fob is the easiest way to perform day to day tasks with the S02 system It has four buttons
11. the appendix Practice arming and disarming until they are second nature When an alarm is triggered sirens are blaring you should know how to disarm the system 2014 Fortress Security Store S02 v1 2 1 Page 46 www FortressSecurityStore com Step 4 Features Including Programming Use a telephone to control the Main Panel remotely If the Main Panel is connected to a telephone line some features of the system are accessible by any telephone whether it is a cell phone or landline Calling in only works if there is no device which picks up the call first such as a fax machine or answering machine If the Main Panel calls out a fax or answering machine does not matter Calling the Main Panel 1 Dial the number of the S02 s phone line 2 The Main Panel system will answer and emit a beep 3 Enter passworp The Main Panel will emit a beep to confirm each keystroke 4 Press a key on your phone to perform actions 1 Away Arms the system immediately equivalent to out button 2 Disarms the system immediately Listens to sounds using the microphone in the Main Panel can be repeated Hangs up 2014 Fortress Security Store S02 v1 2 1 Page 47 www FortressSecurityStore com Answering When the Main Panel Calls Out If the Main Panel calls out and you answer the call the process is the same as calling in except you do not have to enter a password and you have only two options Stops the Main Panel from making any more cal
12. 014 Fortress Security Store S02 v1 2 1 Page 58 www FortressSecurityStore com Door Window Sensors Place the magnet and transmitter side by side PASSWORD 2 beeps out and home LEDs on 7 zone zone between 01 32 usually 09 29 Separate magnet andtransmitter 2 beeps RETURN RETURN 2 beeps out and home LEDs off If this is a door that you want to use for access without triggering an alarm you must set the zone type to delay To set it to delay it must be in Zone 01 08 PASSWORD 2 beeps out and home LEDs on zone2 2 2 beeps X is 2 Delay Mode RETURN OF RETURN RETURN 2 beeps out and home LEDs off If this is a door and you want to have it chime when someone enters exits and the Main Panel is disarmed you will need to PASSWORD 2 beeps out and home LEDs on 7one 7 1 2 beeps RETURN 2 beeps out and home LEDs off 2014 Fortress Security Store S02 v1 2 1 Page 59 www FortressSecurityStore com Key Fob Remote Controls PASSWORD 2 beeps out and home LEDs on 7 zone zone is usually 30 32 Press Remote s Alarm speaker icon 2 beeps RETURN RETURN 2 beeps out and home LEDs off Panic Buttons PASSWORD 2 beeps out and home LEDs on 7 zone zone is usually 03 05 Press large red button 2 beeps RETURN RETURN 2 beeps out and home LEDs off 2014 Fortress Security Store S02 v1 2 1 Page 60 www FortressSecurityStore com Outdoor Siren Black Siren The video Outside
13. 1 2 1 Page 1 www FortressSecurityStore com Step 5 Program Telephone Nombers varmnsmnmensenmndeernndensjmnmeamevmedeninde 26 Step 6 Optional Record a voice message to be distributed by phone in case of an alarm trigger 28 Step 7 Install and Prepare Sirens External Sensors and Detectors eeseseeeseeeesereereerreserereererseserss 30 Step 8 Learn and Use the key fob for Remote Control 34 Slow St rt TOIT EEN 35 Slow Start Unpack Setup amp Install Your S02 System usmeaarsunmevemnnandsmsi unni 36 Step I Check the contents of the Fortress Security Store System box 36 Step 2 Pla the ME e sssini sscsocisirasitsoror isare istesin ie aas Eao ERSEK EEE 37 Step 3 Finish programming the Main Panelm nemes 39 Slow Start Use th S02 SEN de 42 Step 1 Learn about Features and Applications of the S02 Bvstem 42 Step 2 Definition of Key Terms such as Zones Sensors Detectors Alarms Tnggers 43 Step 3 Arm Disarm State of the System asbie 45 Step 4 Features Including Programming eeseseeseesrsesresesstrsresresstesresrssersteseesteseesernstenseseresrensesee 47 Use a telephone to control the Main Panel remotely AAA 47 Add Delete Move Sensors and Detectors Luma gedd Eet EEdeE gedd 49 Change Delay Zone Type Setting ugeet 50 Use the Door Chime System Arm Reminder Function 00 0 eeeceeseeeseceseeeseeeeseeceaeceeeseeeeeaeeeaeens 53 Phone Line Trouble or Cut Line Reminder vase Eed EehE 54 Ring Count
14. Before Main Panel Answers mum saa cicddeeaubodeaiandedevacetneeseutezes 55 MER Natt 55 Siren Ga E 56 www FortressSecurityStore com Tee EEE EE EE atana R anais 57 Slow Start Registering or Re registering Devices with the Main Panel 58 PIR Motion Dee sara Geer 58 Door Window Sensors ineno aE NE RE E E REA E EERE 59 Key Fob R mot e EE 60 Frede iee EE E ana E EE E a a ER 60 Outdoor Siren Black Sen 61 Pet Immune Motion Det ctotS E 63 Appendices ua a EEEE E A a aaae 64 Appendix A Command Summary EE 65 Appendix B System Maintenant sissors ieni nni e A EEE E EATR ENa 70 Appendix C Technical Information Selected System Components s ssesseseseseeeeesersrierresrrseeseresee 72 Main Pantie RE 712 Wireless Door Window Sensor sssseseesssesesssertesseseesssseessssereesseeessetesssstessssresssereesssseesssseesese 73 Wireless PIR Motion DEEN geegaeegegeeet egene 74 FN 74 2014 Fortress Security Store S02 v1 2 1 Page 3 www FortressSecurityStore com Foreword Thank you for choosing the 502 series alarm system from Fortress Security Store For your safety please read the operations manual before using the system This manual gives detailed steps for common operations The reference section of the manual will be most helpful if changes need to be made to the preprogrammed system If you are familiar with alarm systems you should go directly to the Quick Start section ATTENTION Your S02 series alarm sy
15. Strobe Sirens 0 0 1 0 0 0 Solar Sirens 0 0 0 0 0 0 Glass Break Detectors 0 0 0 0 1 1 Smoke Detectors 0 0 0 1 0 1 Gas Detectors 0 0 0 0 0 0 Water Detectors 0 0 0 0 0 0 Extra number pad 0 0 0 0 0 0 Step 2 Plan the Installation 2014 Fortress Security Store S02 v1 2 1 Page 36 www FortressSecurityStore com Using a worksheet like the one below prepare a plan for placing detectors sensors and sirens in your house or small business Door window sensors and motion detectors have numbers on the back that identify the zone they are in It may be handwritten or printed By keeping a chart of where each device is placed alarms and locations can be identified by the devices that trigger them Layout Worksheet Device Zone Location Motion Detector 1 1 Dining Room Window Sensor 4 7 Kitchen window above sink NN NM WWW Key Fob Remote 1 30 Automobile Key Fob Remote 2 31 Kitchen Table Outside Siren N A Eave of Garage 2014 Fortress Security Store S02 v1 2 1 Page 37 www FortressSecurityStore com Zone Assignments Zones 01 08 have additional features S02 A Device amp Number Zones S02 B Zones S02 C Zones S02 D Zones S02 E Zones S02 F Zones Main Panel N A N A N A N A N A N A Motion Detector 1 OI 01 OI 01 OI 01 Motion Detector 2 02 02 02 02 02 02 Motion Detector 3 N A 03 N A 03 03 03 Motion Detector 4 N A N A N A N A N A 04 Panic Button 03 04 03 04 04 05 Smoke N A N A N A 05 N A 06 Glass Br
16. anel e Arming and alarm features accessible from a key fob remote or phone e 99 detectors sensors supported e Zones 01 08 can be selectively armed delayed active despite armed status and disabled e Multiple remote controls supported each with its own code pairing e Intercom microphone for remote monitoring and communication e 72 hour backup battery when home power is not available e Expandable with additional sensors detectors smoke alarms etc e One touch arming from Main Panel and key fob remote 2014 Fortress Security Store S02 v1 2 1 Page 8 www FortressSecurityStore com e Arming disarming audio monitoring from telephone e Chime feature to signal when a door has been opened e Versatile alarm programming features and notifications o Home and Away arming methods with programmable delay 32 Wireless Zones and 7 Wired Zones Siren and remote siren Phone Alerts up to 6 numbers notified Beep alert for the Telephone Line Cut and siren alert for control frequency interference function o 0 0 a Refer to the rest of the manual for additional major and secondary features 2014 Fortress Security Store S02 v1 2 1 Page 9 Front of Main Panel Fortress Security Store S02 1 Main Panel display and status indicator 2 Tactile keypad Main Panel Display and Status Indicators The display shows the status of the alarm system during operation and provides information during the programming and alarm process
17. anyone who answers The message can be up to 10 seconds long and can be as descriptive as Alarm repeated twice or This is Bob s alarm system saying there has been an alarm triggered at 1234 Stone St Smalltown Wisconsin Please call 911 1 Record the message A Enter password Main Panel emits two beeps B Enter 6 LCD panel begins countdown from 10 seconds C Record a message speaking into the MIC on the left side panel of the Main Panel LCD panel displays 00 Main Panel emits two beeps Press return or wait for the time out and Main Panel will emit two beeps 2014 Fortress Security Store S02 v1 2 1 Page 28 www FortressSecurityStore com 2 Listen to the message Requires a telephone connected to the same line as the Main Panel A Enter password Main Panel will emit two beeps B Enter 6 LCD panel will display count up from 1 10 C Listen to the message on the connected phone If desired go through the programming steps again and the new message will overwrite the old one 2014 Fortress Security Store S02 v1 2 1 Page 29 Step 7 Install and Prepare Sirens External Sensors and Detectors There is a separate section on mounting sensors motion detectors and other components but the directions in this step allow getting started quickly The PIR Passive Infrared motion detectors in the package are designed to trigger an alarm when they see motion They are not active when using the Home Home Arm fun
18. ction The door window sensors in the package are already programmed so they are active when using the Out Away Arm or Home Home Arm function www FortressSecurityStore com To test devices at this point disconnect the siren since it will be very loud There will be enough feedback from the LCD display and status lights 1 Mount the motion detector bracket between 6 and 8 feet above the floor The bracket has a ball and socket mount which allows the detector to be aimed optimally Turn on the power switch A To test the detector arm the system Away Arm by pressing the Out key for two seconds Main Panel emits a beep Out LED blinks for 30 seconds After 30 seconds the Main Panel emits another beep and the Out LED will turn on 1 Create motion in front of the motion detector The alarm LED will turn red The zone number will appear in the LCD display Main Panel will emit a click Note If you test a motion detector wait 30 seconds before testing it again To protect its battery a motion detector will not light its LED more than once in 30 seconds even if it detects something during that period 2014 Fortress Security Store S02 v1 2 1 Page 31 www FortressSecurityStore com 2 Door Window sensors detect the opening of a door or window Two objects one a wireless transmitter and the other a magnet make up a door window sensor They should be mounted within 1 2 of each other one on the moveable side of the door window The magnet
19. eak N A N A N A N A 05 07 Door Window Sensor 1 04 05 04 06 06 08 Door Window Sensor 2 05 06 05 07 07 09 Door Window Sensor 3 06 07 06 08 08 10 Door Window Sensor 4 07 08 07 09 09 11 Door Window Sensor 5 08 09 08 10 10 12 Door Window Sensor 6 N A 10 09 11 11 13 Door Window Sensor 7 N A 11 10 12 12 14 Door Window Sensor 8 N A 12 11 13 13 15 Door Window Sensor 9 N A 13 12 14 14 16 Door Window Sensor 10 N A 14 13 15 15 17 Key Fob Remote I 30 30 30 30 30 30 Key Fob Remote 2 31 31 31 S 31 31 Key Fob Remote 3 N A 32 32 32 32 32 Step 3 Finish programming the Main Panel 2014 Fortress Security Store S02 v1 2 1 Page 38 www FortressSecurityStore com Programming the S02 Main Panel is not difficult but there are a few things to learn and remember 1 Programming Hints A All programming begins with entering your password and a pound or number key B A programming session ends when the return key is pressed or a time out occurs appro ximately 30 seconds after the last key press C The asterisk or star key is used for certain tasks including deletion Be careful with any command that includes so that programming is not accidentally deleted D Beep codes give audible hints about what is happening Every keystroke gets a beep for audible feedback Two beeps mean success or return Such as a timed out command Four beeps generally mean failure such as an illegal entry Two or four beeps when pressing return mean Prog
20. ed changing Description of Zone Types Zone Type 1 Default type Any device with this zone type will trigger an alarm under any armed condition and will not trigger an alarm when the system is disarmed All door window sensors are programmed Type 1 as a default Remember zones 09 32 are Zone Type 1 and cannot be modified So it is a good idea to save zones 01 08 for devices you may want to modify 2014 Fortress Security Store S02 v1 2 1 Page 51 www FortressSecurityStore com Zone Type 2 By default this zone type delays triggering an alarm for 30 seconds The delay time can be set from 0 90 seconds The delay can be set differently for entry and exit An entry delay allows time for entering a protected area while the system is armed and taking 0 90 seconds to disarm the Main Panel Once triggered there is no way to stop the count down other than disarming the Main Panel For example opening the door while the system is armed starts the countdown the Main Panel beeps every second and closing the door so the sensor is reset does not halt the counter An exit delay is the amount of time you have to leave a protected area once you have pressed the Armed Away button before delayed zones start triggering alarms Zone Type 3 Devices with this zone type always trigger an alarm whether the system is armed or not It is used for devices like Panic Buttons gas water and smoke detectors Zone Type 4 This zone type disabl
21. elected System Components Main Panel Power Supply AC 220V 10 DC 12V US 110 120V AC Rechargeable Backup Battery Ni MH DC 7 2V Working Current lt S5OmA Alarm Current lt 300mA Wireless Receiving Frequency 433MHz 0 5MHz Wireless Receiving Sensitivity SmV m Anti jamming Intensity 1V m frequency range 20 1000 MHz Outside Alarm Siren lt 110db Working Condition Temperature 14 104F Relative Humidity lt 90 2014 Fortress Security Store S02 v1 2 1 Page 72 www FortressSecurityStore com Wireless Window DOOR Sensor Battery 12V 23A Static Current lt 20uA Transmission Current lt 15mA Transmission Frequency 433MHZ 0 5MHZ Wireless Range No obstacle 150feet Transmitter Magnet Gap Distance 1 2 Inch Working Condition Temperature 14 104F Relative Humidity lt 90 2014 Fortress Security Store S02 v1 2 1 Page 73 www FortressSecurityStore com Wireless PIR Motion Detector Battery DC 9V Static Current lt 100uA Transmission Current lt 20mA Transmission Frequency 433MHZ 0 5MHZ Wireless Range No obstacle 650 feet Detection Speed 1 10ft sec Detection Distance 15ft to 25 ft Detection Range Horizontal 110 Vertical 60 Working Condition Temperature 14 104F Relative Humidity lt 90 Remote Controller Power Supply DC 12V built in 12V battery Static Current 0 Transmission Current 15mA Transmission Frequency 433 0 5 MHz Wireless Range No obstacle 150 feet Worki
22. eos Below is a listing for each individual video Click on the title to view it Installation Videos Introduction Video Demonstration of Window amp Door Contacts Unboxing Motion Sensor Main Panel Remote Control Window Door Contact Panic Button Window Door Contact Applying Tape 2014 Fortress Security Store S02 v1 2 1 Page 20 www FortressSecurityStore com Programming Videos Main Panel Operation Door Chime Main Panel Programming Phone Line Cut Change Password Change System Zone Setting Phone Numbers Remote Control System Recording Message Outside Alarm Alarm Chirp Wireless Strobe Alarm Delay Additional Accessories Alarm Sounding Reset System Set Ring Time Step 3 Install the Main Panel 2014 Fortress Security Store S02 v1 2 1 Page 21 www FortressSecurityStore com The Main Panel should be installed near a power outlet and if phone capabilities are desired near a telephone connection It should be centrally located if sensors are distant or on the other side of multiple walls 1 Plug the system s power cable into the wall then attach the other end to the Power jack next to the antenna 2 Turn on the unit using the on off switch on the left side panel This will begin charging the battery which should be near full charge already Note The Main Panel is only ON when the switch is on The battery backup does not work if the device
23. es the device assigned it It is handy for temporarily disabling a malfunctioning device preparing it to be moved or allowing a battery change Zone Type 5 This zone type works only in the Armed Away out mode Motion detectors are most commonly assigned this zone type 2014 Fortress Security Store S02 v1 2 1 Page 52 www FortressSecurityStore com Use the Door Chime System Arm Reminder Function Turning this feature on or off for a particular door window sensor zone causes the Main Panel to emit three beeps if the sensor is triggered while the system is disarmed It can be used to remind you to arm the system when you leave by a specific door It can also act as a bell such as when a customer opens a door and enters To turn on this feature press PASSWORD 2 beeps out and home LEDs on 7one 7 1 2 beeps RETURN 2 beeps out and home LEDs off To turn off this feature press PASSWORD 2 beeps out and home LEDs on zone 7 O 2 beeps RETURN 2 beeps out and home LEDs off Note For this command to work zone must be Zone 01 through 08 If the device is in any other z one you must first register it in zones 01 08 using the devices regular registration procedure 2014 Fortress Security Store S02 v1 2 1 Page 53 www FortressSecurityStore com Phone Line Trouble or Cut Line Reminder This function warns you if your phone line is cut or phone service is disrupted If the system is armed the wired siren sounds w
24. hen enabled will beep when it does not sense a telephone connection 1 Program the first number into the Main Panel A Enter password Main Panel emits two beeps B Enter 31 telephone number Enter another number see next step press RETURN or wait for the time out 2 Enter another number 32 telephone number Numbers can be entered as long as there is no time out or return is not pressed Use 33 36 for the remaining phones 2014 Fortress Security Store S02 v1 2 1 Page 26 www FortressSecurityStore com 3 If no phone line is attached use the following command to keep the Main Panel from warning it does not have a phone connection A Enter password Main Panel emits two beeps B Enter 22 0 Press return Or wait for the time out and Main Panel will emit two beeps Note The system is designed to use a 10 digit North American phone number but international and other numbers are also supported Experiment If your number does not work For example if the 10 digit number does not work add a 1 in front of it 1 123 456 7890 Likewise if your number is only 8 digits long add two zeros at the end 8 765 4321 00 2014 Fortress Security Store S02 v1 2 1 Page 27 www FortressSecurityStore com Step 6 Optional Record a voice message to be distributed by phone in case of an alarm trigger Note When an alarm is triggered and the Main Panel calls the listed phone numbers one pre recorded voice message will be played for
25. igit of the display after the is pressed Main Panel emits two beeps after the is pressed 3 Press RETURN to exit programming mode Main Panel emits two beeps Out and Home lights turn off Note If RETURN is not pressed the Out and Home light will turn off approximatel y 30 seconds later In programming mode Out and Home lights are both on if no keypad entry is made within 30 seconds the Main Panel exits programming m ode and the Main Panel emits two beeps It is the functional equivalent of pressi Ng RETURN 2 You have changed your password to password and 1234 will no longer function as a password Note It is wise to keep your new password somewhere it can be retrieved if necessary 2014 Fortress Security Store S02 v1 2 1 Page 25 www FortressSecurityStore com Step 5 Program Telephone Numbers When a sensor or detector is triggered the Main Panel calls up to six 6 telephone numbers that are programmed into its memory This can alert you your family the police station or designated individuals that something has happened at your location At least one phone number must be programmed into the Main Panel If there is no plan to have the Main Panel call out to any number use 555 555 5555 as a number and make sure no telephone line is connected to the out line telephone jack on the Main Panel If no phone line is connected the Main Panel must be programmed so that it will disable the Phone Line Cut feature This feature w
26. ireless sirens will not sound If the system is disarmed the Main Panel emits 3 beeps every 10 seconds or so If you do not have a telephone line connected to the Main Panel be sure this is turned off It should be turned on only if you have stable telephone service To turn on this feature press PASSWORD H 2 beeps out and home LEDs on 22 1 2 beeps RETURN 2 beeps out and home LEDs off To turn off this feature press PASSWORD 2 beeps out and home LEDs on 22 0 2 beeps RETURN 2 beeps out and home LEDs off 2014 Fortress Security Store S02 v1 2 1 Page 54 www FortressSecurityStore com Ring Count Before Main Panel Answers The Main Panel will accept phone calls see Use a telephone to control the Main Panel remotely from any cell phone or landline if the ring number is greater than 00 The permissible values are 00 12 As stated elsewhere in the manual this function will not work in conjunction with answering machines modems and most fax machines To change the number of rings before the Main Panel answers the telephone PASSWORD 2 beeps out and home LEDs on 12 XX 2 beeps XX is rings from 00 12 RETURN 2 beeps out and home LEDs off Siren Alert Time You can adjust how long your siren sounds when an alarm is triggered The default is 1 minute The permissible values are 00 30 minutes To change the length of time the siren sounds on a triggered alarm PASSWORD 2 beeps out and ho
27. l connection This is a microphone used to monitor the interior of the house or record a message to be sent out by telephone when an alarm is triggered Power Antenna Panel 1 Power Use the power cord packaged with the S02 for best results 2 Antenna Extending the antenna allows sensors and other alarm devices to be mounted further from the Main Panel www FortressSecurityStore com Quick Start Your Fortress Security Store alarm system is preprogrammed before shipping so a minimal amount of programming will be needed before operation This section is here so you can plug and play if you do not want to do a lot of reading first For any problems re watch the videos in Step 1 or use the information below to contact Fortress Security Store CALL 253 468 0196 EMAIL Support FortressSecurityStore com ATTENTION Your S02 series alarm system is preprogrammed except for those items detailed in Step 4 7 of the Quick Start section If you get additional sensors motion detectors smoke alarms etc please follow the instructions for installing those DO NOT re program the Main Panel or return it to the factory settings without first consulting Fortress Security Store Remember The Default Program Password is 1234 2014 Fortress Security Store S02 v1 2 1 Page 16 www FortressSecurityStore com Change this password to a four digit number you can remember but not one others can easily guess This is the pas
28. ls Leaves the Main Panel armed and with the alarm LED lighted Any activated sirens are turned off S Allows you to listen to the microphone in the Main Panel for 30 seconds If you press nothing while listening for 30 seconds the phone call terminates The Main Panel continues making calls and all sirens continue Note Pressing then while listening to the microphone stops the Main Panel from making any more calls and leaves the Main Panel armed and with the alarm LED lighted Any activated sirens are turned off 2014 Fortress Security Store S02 v1 2 1 Page 48 www FortressSecurityStore com Add Delete Move Sensors and Detectors If you need more devices than came with your kit you will need to program them when they arrive To put a new unit in service 1 turn off all motion detectors or make sure they are NOT triggered during the install 2 designate the physical location 3 select a zone either in their own zone or sharing a zone with another device 4 program them 5 mount them in their physical location and 6 test them per instructions in the appendix For most devices to get them registered have them near the Main Panel and enter PASSWORD 2 beeps out and home LEDs on 7 zone Zone number in LCD activate the device 2 beeps RETURN OF RETURN RETURN 2 beeps out and home LEDs off pull sensors apart or move in front of motion detectors To delete a device just remove the battery or power s
29. me LEDs on 29 XX H 2 beeps XX is minutes from 00 30 RETURN 2 beeps out and home LEDs off Siren Chirp With this function enabled arming or disarming the system is followed by chirps or beeps from system 2014 Fortress Security Store S02 v1 2 1 Page 55 www FortressSecurityStore com sirens This is handy for getting feedback on whether the remote control s signal actually reached the Main Panel Most commonly it allows a person to press disarm while outside and use the siren s beep chirp as confirmation the system is disarmed and the area can be entered without triggering an alarm To enable the siren echo of remote control key presses PASSWORD 2 beeps out and home LEDs on 8 2 beeps RETURN 2 beeps out and home LEDs off To disable the siren echo of remote control key presses PASSWORD 2 beeps out and home LEDs on 8 2 beeps RETURN 2 beeps out and home LEDs off 2014 Fortress Security Store S02 v1 2 1 Page 56 www FortressSecurityStore com Change Password For security or convenience you may want to change your password It must be a 4 digit number and is changed by this sequence PASSWORD 2 beeps out and home LEDs on old password 10 L appears in LCD display PASSWORD 2 beeps out and home LEDs off NEW password RETURN 2 beeps Factory Reset This function removes ALL programming from the system and resets the password to the default 1234 All sensor and detector regist
30. ng Condition Temperature 14 104F Relative Humidity lt 90 2014 Fortress Security Store S02 v1 2 1 Page 74
31. ource and physically remove it If you want to have it function in a new location or zone that is considered a move A move is really just an add toa new zone so the directions are the same as above 2014 Fortress Security Store S02 v1 2 1 Page 49 www FortressSecurityStore com Change Delay Zone Type Setting Zones 01 08 are special in that they have more attributes than 09 32 Zones 01 08 have the following zone type possibilities 1 Instant Zone Default Alarms are immediate 2 Delay Zone Alarms are delayed 0 90 seconds default 30 seconds 3 Emergency Zone Alarms always on armed or disarmed system 4 Disable Zone Alarms are disabled 5 Away Armed Zone Alarms only active when Away Alarm out is on To change a Zone Type setting enter PASSWORD 2 beeps out and home LEDs on zone 2 zone type 2 beeps RETURN OF RETURN RETURN 2 beeps out and home LEDs off 2014 Fortress Security Store S02 v1 2 1 Page 50 www FortressSecurityStore com To change an Entry Delay setting for Type 2 Zones enter PASSWORD 2 beeps out and home LEDs on 28 XX 2 beeps xx is 01 90 seconds RETURN OF RETURN RETURN 2 beeps out and home LEDs off To change an Exit Delay setting for Type 2 Zones enter PASSWORD 2 beeps out and home LEDs on 27 XX 2 beeps xx is 01 90 seconds RETURN OF RETURN RETURN 2 beeps out and home LEDs off The S02 kits are programmed to take advantage of these settings and normally do not ne
32. plete functioning While there is no hard and fast rule it is wise to check every device at least once in a three month period For greater safety and reliability check more often Much of the periodic maintenance is satisfied by the normal operation schedule For example if you use the arming timer you will be able to see if the arm and disarm function is working at the Main Panel When testing troubleshooting malfunctioning components that use batteries replace the battery first to see if that solves the issue 2014 Fortress Security Store S02 v1 2 1 Page 70 www FortressSecurityStore com The following table lists periodic maintenance tests Maintenance Tasks and Suggested Frequency Task Frequency What How Arm Disarm Quarterly Arm in all modes Away Arm Home Arm and disarm Triggered Alarm Quarterly Trigger an alarm and see if the Main Panel dials all the Notification phones in its list and sends SMS data Main Panel Sensor Quarterly Trigger all or a rotating subset of sensors detectors to Communication make sure they can communicate with the Main Panel Main Panel Battery Quarterly Remove electrical power for 1 2 hours to see if backup battery power works Detectors Sensors Remo Monthly Check that batteries are working by inspection or te Controls triggering alarms 2014 Fortress Security Store S02 v1 2 1 Page 71 www FortressSecurityStore com Appendix C Technical Information S
33. ramming Mode Off 2014 Fortress Security Store S02 v1 2 1 Page 39 www FortressSecurityStore com 2 Change your password Use the directions in Step 4 Change Your Password and Program Essential Information in the Main Panel of the Quick Start Guide The default password for the Main Panel is 1234 The password may be changed as often as you like but you MUST remember what it is If it is forgotten no actions can be performed until you reset your system to the factory default That will destroy ALL the sensor settings and individual programming 3 Enter telephone numbers to be notified on alarm triggers Use the directions in Step 5 Program Telephone Numbers of the Quick Start Guide to enter telephone numbers to be notified when an event triggers an alarm The system can also dial monitoring facilities but this requires the monitoring facility and perhaps Fortress Security Store to help set up the system Note Some locales allow direct notification to a police department phone number while other locales strictly forbid it often with a hefty fine attached It is worthwhile to find out what the local ordinance is where the system is used 2014 Fortress Security Store S02 v1 2 1 Page 40 www FortressSecurityStore com 4 Optional Record and Playback a Message to be distributed when an alarm is triggered Use the directions in Step 6 Optional Record a voice message to be distributed by phone in case of
34. rations ring settings zone settings everything Please do not use this function without consulting Fortress Security Store To completely reset your system PASSWORD 2 beeps out and home LEDs on 0000 2 beeps RETURN RETURN 2 beeps out and home LEDs off 2014 Fortress Security Store S02 v1 2 1 Page 57 www FortressSecurityStore com Slow Start Registering or Re registering Devices with the Main Panel The process of taking an alarm system device and getting it to be recognized by the Main Panel is called registration or coding Each S02 system ships with all registration done If new devices are added if a device loses registration or needs to be re assigned registration must be performed Note If a device has an on off switch or method of turning it off it is best to turn it off while programming a different new device If active it can accidentally re register to the new zone This is particularly important with motion detectors PIR Motion Detector Turn on the switch on the side of the motion detector PASSWORD 2 beeps out and home LEDs on 7 zone zone between 01 08 Create Motion in front of detector 2 beeps RETURN RETURN 2 beeps out and home LEDs off Since you will want this device to be active only in Away Alarm mode change it s zone settings PASSWORD 2 beeps out and home LEDs on zone2 5 2 beeps X is 5 Away Armed Zone RETURN OF RETURN RETURN 2 beeps out and home LEDs off 2
35. stem is preprogrammed except for those items detailed in Step 4 7 of the Quick Start section If you get additional sensors motion detectors smoke alarms etc please follow the instructions for installing those DO NOT re program the Main Panel or return it to the factory settings without first consulting Fortress Security Store 2014 Fortress Security Store S02 v1 2 1 Page 4 www FortressSecurityStore com Copyright Information The product including but not limited to granted or pending patents is under protection of the patent laws of the United States or other countries We reserve the right to modify the specification or price of the product This manual its photographs text and illustrations are under copyright and should not be used without the written permission of Fortress Security Store Purchasers of a Fortress Security Store alarm system are hereby given permission to use this manual in operating their purchased systems 2014 Fortress Security Store S02 v1 2 1 Page 5 www FortressSecurityStore com Safety Precautions e Use the power supply that is shipped with the product Use of any other power supply may damage the alarm system e Maintain air flow around all surfaces of the system e Keep the surfaces of the product clean and dry e Operate the Main Panel in a dry dust free environment e Operate the alarm in areas where there are no combustible materials and flammable gasses e Use minimal force on the keys
36. sword used to program any devices or services In addition it is used to turn off sirens and alarms at the Main Panel so it should be a number easily remembered under stress While it makes no difference whether it is changed before or after setting up the system changing it first so it is used frequently will help you remember the password 2014 Fortress Security Store S02 v1 2 1 Page 17 Step 1 Unpack Use the chart and photos on this and the next page to be sure all system items are included The contents of the box should look something like the examples here Call or email Fortress Security Store if something is missing www FortressSecurityStore com Packing List Custom Components S02A S02B S02C S02D S02E SO2F Ad rek I Main Panels 1 1 1 1 1 1 Motion Detectors 2 3 0 3 3 4 Pet Motion Detectors 0 0 2 0 0 0 Panic Buttons 1 1 1 1 1 1 Door Window Sensors 5 10 10 10 10 10 Key Fob Remotes 2 3 3 3 3 3 Sirens 1 1 1 1 1 1 Outdoor Sirens 0 1 0 1 1 1 Strobe Sirens 0 0 1 0 0 0 Solar Sirens 0 0 0 0 0 0 Glass Break Detectors 0 0 0 0 1 1 Smoke Detectors 0 0 0 1 0 1 Gas Detectors 0 0 0 0 0 0 Water Detectors 0 0 0 0 0 0 Extra number pad 0 0 0 0 0 0 2014 Fortress Security Store S02 v1 2 1 Page 19 www FortressSecurityStore com Step 2 Watch Videos If possible watch the following videos They are very helpful in understanding the S02 system All videos are available at www fortresssecuritystore com s02vid
37. ther 2014 Fortress Security Store S02 v1 2 1 Page 44 www FortressSecurityStore com Step 3 Arm Disarm State of the System The only alarms that can be triggered when the 502 is disarmed are emergency zones and panic button presses There are two armed states and each has different characteristics Home Armed Designed to be used when people are inside the protected zone No motion detectors with a couple of exceptions Armed at the Main Panel or a Key Fob Remote Arming is done without delay Away Armed Out Designed to be used when people are not inside the protected zone All detectors sensors are used Armed at the Main Panel a Key Fob Remote or a telephone Arming is delayed to allow leaving the premises after arming Arming Procedure Main Panel Press out Away Arm or home Home Arm button for approximately 3 seconds Key Fob Remote Press House icon Home or Closed Lock icon Away for about 2 seconds Telephone Use telephone key see Use a telephone to control the Main Panel remotely 2014 Fortress Security Store S02 v1 2 1 Page 45 www FortressSecurityStore com Disarming Procedure Main Panel Enter rassworp then press disarm button Key Fob Remote Press Unclosed Lock icon for about 2 seconds Telephone Use telephone key see Use a telephone to control the Main Panel remotely It is unusual to have to do anything but arm and disarm your system and perform periodic maintenance as described in
38. windows doors are opened in disarm mode Only zones 1 8 can be programmed to chime 2014 Fortress Security Store S02 v1 2 1 Page 67 www FortressSecurityStore com key Monitor Action Command Notes Loud siren chirp when 8 ON System Default arming disarming alarm system 8 OFF Telephone line cut or short 22 1 ON System Default circuit alert 22 O OFF Siren Alarming Time 29 MM MM 00 30 minutes default 01 minute Factory Reset 0000 Danger Danger All Sensors and remotes will be deleted Do not use without consulting with Fortress Security Store i RR rings 00 12 default 00 answer Ring number Main Panel answers 12 RR immediately on when called from remote phone Options when communicating with 1 key Arm Arming type is Away Arm Main Panel via telephone 2 key Disarm Listen through Main Panel Mic for 30 seconds or until you press another 2014 Fortress Security Store S02 v1 2 1 Page 68 www FortressSecurityStore com Action Command Notes valid option 1 2 If you were called by device and key Stop notification and call press no more notification calls are made 2014 Fortress Security Store S02 v1 2 1 Page 69 www FortressSecurityStore com Appendix B System Maintenance Both the Main Panel and the sensors detectors remote controls and other devices need to be checked periodically for com
39. www FortressSecurityStore com 2014 Fortress Security Store Page 1 Fortress Security Store SO2 Alarm www FortressSecurityStore com Table of Contents Fortress Security Store S02 Alarm System o co cicccssssisssacecssstaversianceassasdavcesasedeedaassvedesasnesadeasseventagnsswasasdocees 1 F L 4 Copyricht Informati n EE 5 Safety PrecanuohsLuasmeudnneamnee mdaune tn EEES AEE EA Taane REE aE ERa EEEa anh 6 Ku Ga REE RR EE ER PRE 7 Description f the Alarm Systemi socia ei E E EE E E 8 Mr 8 Front of Main Panel Fortress Security Store S02 uasnsesgdpmnised mameidpedjdgoniddan 10 Main Panel Display and Status Indicators Luaveameesmmenmadksteimimeunjnmeagd rsaintumjnee 11 Tactile e RE EE NR EEE EE AER N 12 Back and Side of Main Panel Fortress Security Store S02 srrsnvrnrnvnvnrnnrnrnrnvnnnnvnrvraseverenvnnvnenevressnn 13 DBUS Bar aiid Connections detresse eege ee 13 Main Panel Physical Connections sesseeeseseessessessresresrsseseresressrssrerrenstrstssteeseestesruseeseseresresseeerst 14 P wef Antenna e E 15 Krk Statt sasiesceaeidasiaicaasuecedes peedadcacievacsuseadcaansvsnensadeaied avsuenaasasigeaceaneneas aaliyceditsansaa sina AEE R 16 Step 1 ITD ACM SEERE RE ON E EEN EEE EAEE 18 Packing EE 19 Step VW ao EN EE NE NE 20 Step 3 Install Sr EE eege 22 Step 4 Change Your Password and Program Essential Information in the Main Panel 24 2014 Fortress Security Store S02 v
40. y Store S02 v1 2 1 Page 65 www FortressSecurityStore com Action Command Notes Disarm the system Press PASSWORD then disarm key default 1234 Enter Programming Mode PASSWORD default 1234 Exit Programming Mode Press RETURN key twice Return to operational mode Add phone number to alarm notification list Program mode then 31 36 NNN NNN NNNN NNN NNN NNNN is a 10 digit phone number Record outgoing voice message 6 Message played to notification list after alarm Replay outgoing voice message 6 Review message played to notification list Code a wireless detector to ZONE 7 ZONE 01 08 zones are for detectors and devices that need to set a zone type or delay 09 29 are instant alarm zones and cannot be modified 30 32 are usually reserved for remote controllers 2014 Fortress Security Store S02 v1 2 1 Page 66 www FortressSecurityStore com Action Command Notes ZONE 01708 09 32 are instant zone only Change delay mode or zone type ZONE 2 X X is zone type 1 instant 2 delay 3 emergency such as fire smoke water panic 5 Away Armed motion detectors etc 0 disabled Delete all wireless sensors 7 Danger This is a drastic action that should be avoided unless advised by Fortress Security Store Window Door Chime ZONE 7 1 ON Pick the zones you want to ZONE 7 OH OFF System Default chime when the
Download Pdf Manuals
Related Search