SL-3GHD128128-RC User manual
Contents
1. MRP TCP IP This option is only applicable to the Sublime range It selects the Ethernet protocol as nevion com 15 SL 3GHD128128 RC Rev A the control option and disables the RS 232 port of that device MRP is always enabled when any TCP IP based protocol is selected This makes it possible to use Sublime panels when a third party protocol is selected Leitch Pass Through RS 232 This option allows support for Leitch Pass Through protocol via RS 232 interface The details of this protocol are described in Leitch Routing Switchers Serial Protocol Reference Edition E See also Appendix B 1 for details This option is not supported over NCB Leitch Pass Through TCP IP This option allows support for Leitch Pass Through protocol via TCP IP interface The details of this protocol are described in Leitch Routing Switchers Serial Protocol Reference Edition E The interface is using port 23 for this protocol option same port as for Telnet applications See also Appendix B 1 for details The Leitch Pass Through selections are only available on Sublime routers with FW version 2 4 x and higher Grass Valley Native protocol TCP IP This option allows support for Grass Valley Native protocol via TCP IP interface using port 12345 The subset of this protocol that is supported by Sublime routers is described in Appendix B 2 The Grass Valley Native protocol is only available on Sublime routers with FW version 2 52. 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD64128 RC 64x128 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD12864 RC 128x64 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD32128 RC 32x128 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm nevion com 6 SL 3GHD128128 RC Rev A Item Description SL 3GHD12832 RC 128x32 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD9696 RC 96x96 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD6496 RC 64x96 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD9664 RC 96x64 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x1
3. ESTER 14 3 6 Configuring switching time E 15 3 7 Configuring protocol e TEE 15 3 8 Configuring Neu NS EE 16 38 Wale e DEE 16 3 9 Configuring Output options EE 17 3 95 1 OUIPUI eet 17 3 9 2 Slew rate settings we lel air katon ka ki eti oka eka kk tk b kan ia bat dak ek ae oo ea ka pa bas in 17 E Laser Settings ok tb aaa a od an fe hand e a cack kali e DC a ee e SA fo ee eae E ok ak oke 17 4 LED status indication EE 19 ASA UD E 19 4 2 Alarm states EE 19 4 3 Ethernet states tait boat ar kak ki den kinn ko ko e n eler eenegen tues kk sa mt kw kn 19 5 Router communication desi cv paka tk a dak ke a e a ke e Ek A K A 20 Ee Ee 20 5 1 1 Maximum cable length RS 232 1 W W u u u sseeeeeeerenn erne erne 20 5 2 Ethernet connection av kn ik eka eege p ere D ka kok ig 21 Se FINAL EE eet e on a ob e koke tat e a e kn ed aba kan e a eer 21 5 3 NGB CONMCCHO Ie twon is tae cereale aces ok oui kob Fin pie kes ek be aE ede re A tan ea deta 22 5 3 1 Connecting control panels ccc ve kaban vi a a bk solr ved ten e 22 5 3 2 PIN OUE and cable typer s kiye dote rantre sa ap at e os ie bek be ke e pa sa ee a e pe a be e 22 5 3 3 Termination PIWO ee skies pi ekla kan stay ius den kwe kaa sake n ENEE a kan Ra eka ve Ra a 23 5 3 4 e age Re Ee DEE 24 5 3 5 Maximum distance between NCB devices W W W u sssseeeereerne reen rrrnrnnee 24 6 Connecting signal cables to the router AEN 25 6 1 Optical interface aa cee fied st denye kako kon le e pl e em en A
4. Enabled Auto MI HD MION y OK W OK v 17 Enabled Auto HD sl ON y oK se OK v 18 Enabled Auto HD wi ON OK Ob v 19 Enabled Lasel Auto sei HD ON v OK se OK v 20 Enabled Lal Auto HD ivi ON OK v OK v 21 Enabled Auto HD wi ON w OK Lv OK v 22 Enabled Auto HD ON zw OK e OK v 23 Enabled s Auto HD el ON Ok Lv OK v 24 Enabled el Auto HD vw ON OK LOK v 25 Enabled Lasel Auto HD l ON Ok lw OK v 26 Enabled wl Auto HD vw ON wi Ok Ob v 27 Enabled Lal Auto HD el ON OR OK ls 3 9 1 Output reclocker It is possible to enable or bypass Output Reclocker for each router output separately Default is Output Reclocker enabled 3 9 2 Slew rate settings 3 9 2 1 Slew rate mode Set slew rate mode on output Auto Fixed Automatic slew rate detection is only available on reclocking routers Non reclocking routers can only set the options based on Fixed slew rate mode 3 9 2 2 Slew rate Set slew rate to SD or HD Only used when Slew rate mode is fixed 3 9 3 Laser settings This is only applicable on Sublimes with optical I O 3 9 3 1 Laser enabled Enable or disable laser ON OFF It is useful to disable a laser for safety purposes if maintenance is required on the receiving end of the fiber nevion com 17 SL 3GHD128128 RC 3 9 3 2 Laser alarm Indicates alarm on laser OK FAIL 3 9 3 3 Laser temp alarm Indicates high
5. No parity For further details concerning this protocol please refer to the following manual NCB Protocol pdf The DE9 female socket for the serial port of the router has the following pin out Pin RS 232 mode Not in use Tx Rx Not in use GND GND RTS CTS Do Not Connect Note that if the standard RS 232 cable specification DCE is followed 00 NI gt O01 Go PO A cable with Male Male or Female Female connectors at the cable ends is used for Rx Tx crossed connection and A cable with Male Female connectors at the cable ends is used for a straight through connection 5 1 1 Maximum cable length RS 232 IEEE has specified the maximum cable length for an RS 232 connection to 15m Longer distances can be installed depending on the environmental conditions of the installation site It is the responsibility of the installer user to secure a proper installation of the RS 232 connection nevion com 20 SL 3GHD128128 RC Rev A 5 2 Ethernet connection The connections follow the standard set by the IEEE 802 3 100BaseTX specification The cables that are to be applied should be CAT 5 CAT 5E standard or better It is the responsibility of the installer user to secure a proper installation of the Ethernet connection A VikinX Sublime device supports the following setups 100 Mb s half duplex default 10 Mb s half duplex This setup i
6. com 25 SL 3GHD128128 RC Rev A 7 Fan monitoring and replacement This chapter only applies on routers with optical interface Each optical backplane module has a fan which is monitored If the fan fails the LED in front of the Sublime will indicate an error see chapter 4 2 Alarm states It is also possible to use Nevion Configurator to list all alarms In System Overview right click on the Sublime unit and select Properties then choose the Alarms tab If a fan error alarm is active the alarm description will include the number of all optical backplane modules with a faulty fan The number is counting from the bottom giving the lowest module number 1 the next number 2 and so on The fan module is mounted to the optical backplane module with a single screw When replacing a faulty fan module loosen the screw by hand or by using a flat screwdriver New fan modules can be ordered separately BER TCPIP Modules Alarms Advanced Number Description Status Source SL 3GHD1616 160PT 1 Power A failed i i main ctri Power B failed inactive main ot Positive power too low inactive main ctri Negative power too high inactive main ctri Client TCPAP connection inactive main cht No valid product key inactive main ctri SFP error inactive main ctri Fan error SFP module 2 active main ctri nevion com 26 SL 3GHD128128 RC Rev A General environmental requirem
7. rele E lak aa pa RAZ 25 6 2 Electrical interface voye ne ate ke e ket e an Ene 25 7 Fan monitoring and replacement 26 General environmental requirements for Nevion equipment seerne 27 nevion com 3 SL 3GHD128128 RC Rev A ERENNERT 28 Important notes regarding Software in the VikinX Sublime router family range 29 Appendix A Materials declaration and recycling information u ussseneeeree 30 AS Materlals declaratio EE 30 A 2 Recycling Bi e tu Ee BEE 30 Appendix B Additional Protocol miormaton nr rnnnrrnnnne 31 BT Lech Pass Throlgn protoc os geneet eens te epa lan pannan ok ones ia 31 B 2 Grass Valley Native prOtOGOL soi p ske kase ciecsteeteee EgEENNEEEEEAEA EENS EEN NEE EENS 31 nevion com 4 SL 3GHD128128 RC Rev A 1 Product overview Nevion proudly presents Sublime SL 3GHD128128 RC With this router Nevion continues a stable and proven product line including the most complete signal format and size offering available With the ultra slim multi format and flexible product range Sublime fulfils the most demanding requirements from the professional broadcast market This User Manual presents the features installation and operation procedures of the SL 3GHD128128 RC router of the Sublime range The key features of SL 3GHD128128 RC are Multi rate support 3G HD SD SDI Supports DVB ASI Supported bitrates 270Mbps 3Gbps Reclocking on standard 3G HD SD SDI signals Reclocke
8. set Two short XXXXX XXXXX RXRXX XXXXX Power B Only active if power red blinks failed alarm dip is set Red with one YRRRR RRRRR RRRRR RRRRR No valid short yellow product key blink Red with two YRYRR RRRRR RRRRR RRRRR SFP error Only used on routers short yellow with optical modules blinks Red with YRYRY RRRRR RRRRR RRRRP Fan error three short yellow blinks 4 3 Ethernet states The LEDS that are located at the Ethernet bus will after the Start up sequence indicate the Ethernet states On Off Blinking Green Valid link No link Yellow No data Data is transmitted or received nevion com 19 SL 3GHD128128 RC Rev A 5 Router communication You gain access to router for communication purposes by connecting either the router s serial port to your computer or by using an Ethernet connection Do not use both the router s Ethernet port and RS 232 serial port or NCB ports at the same time Doing so may cause loss of important communication and control data 5 1 Serial connection Connection can be made through the serial port of the router see also Chapter 2 5 2 for connection details The communication parameters are configurable Please refer to the protocol documentation of the appropriate communication control protocol Example The protocol parameters of the VikinX Compact routers are as follows Bit rate 19200 bit s Data bits 8 bits Stop bits 1 Parity
9. temperature alarm on laser OK FAIL Rev A nevion com 18 SL 3GHD128128 RC Rev A 4 LED status indication 4 1 Start up The LED located at the front of the router indicates the status of the router At start up the LED will alternate between red R and green G every 500ms for about two seconds After the start up sequence the LED will indicate the Alarm state of the router There are two LEDs located at the Ethernet bus At start up the boot loader is searching for update commands on the serial port for about two seconds During this sequence both Ethernet LEDs will be blinking After the start up sequence the LEDs will indicate the Ethernet state 4 2 Alarm states The LED can either be red R green G yellow Y or have no light N The LED state is here described with twenty letters each representing 100ms which totals to an alarm sequence of two seconds The X indicates that the LED keeps the color it has the moment the alarm sequence begins green yellow or no light Description LED state Alarm Comment Continuous GGGGG GGGGG GGGGG No alarm green light GGGGG Status is OK Continuous YYYYY YYYYY YYYYY YYYYY Unable to This alarm will be yellow light connect to overwritten by other controller over alarms Ethernet Long red RRRRR NNNNN RRRRR NNNNN Power is too blinks low One short RXXXX XXXXX XXXXX XXXXX Power A Only active if power red blink failed alarm dip is
10. the same level The levels can be switched according to the following pattern SWA1 SW2 SW3 SWA Level NCB Address OFF OFF OFF OFF 1 0 OFF OFF OFF ON 2 1 OFF OFF ON OFF 3 2 OFF OFF ON ON 4 3 OFF ON OFF OFF 5 4 OFF ON OFF ON 6 5 OFF ON ON OFF 7 6 OFF ON ON ON 8 7 ON OFF OFF OFF 9 8 ON OFF OFF ON 10 9 ON OFF ON OFF 11 10 ON OFF ON ON 12 11 ON ON OFF OFF 13 12 ON ON OFF ON 14 13 ON ON ON OFF 15 14 ON ON ON ON 16 15 Default level is 1 nevion com 12 SL 3GHD128128 RC 3 3 Router mode SL 3GHD128128 RC allows switching in different modes Router layers Layer sizes 1 layer 128x128 2 layers 64x64 3 layers 42x42 4 layers 32x32 Rev A Switches 5 6 on the configuration switch set the router s mode The Router Management System software must be configured according to the chosen setup The modes can be switched according to the following pattern Router mode 1 router layer 2 router layers 3 router layers SW5 SW6 OFF OFF OFF ON ON OFF ON ON 4 router layers Default mode is 1 router layer Based on the configuration above the I O is connected to the router according to the following scheme 1 layer I O is connected according to information on the rear of the rou
11. through connection nevion com 11 SL 3GHD128128 RC Rev A 3 Configuration This chapter provides an overview of the configuration options that are available on the SL 3GHD128128 RC router Some of the configuration options demand software configuration using the Nevion Configurator This tool is supplied with each router but can also be downloaded from our web site www nevion com support It is important that users apply Nevion Configurator v4 1 1 or a higher version number when configuring the SL 3GHD128128 RC and its variants 3 1 Power Supply setup Before proceeding with router configuration make sure the accompanying power supply unit is configured for the right AC supply voltage There is a switch on the rear side of the power supply module that selects mains voltage The mains voltage can be either 110VAC or 230VAC This switch must be set in the correct position depending on the mains voltage on the router s site Failing to select correct AC mains voltage properly may damage the Power Supply Unit 3 2 Router level Switches 1 4 on the configuration switch set the router s level for communication with the Router Management System and other units in the NCB system The panels on the NCB dedicated to operate with the router must be configured to the same level as that router lf several routers are combined to form an Audio Follow Video RGB or similar system these routers must be configured to
12. 000 OO00000 O00000 o O00000 O0O00000 O00000 OO000000 O00000 O000000 O00000 o O00000 o O000000 O00000 O0O00000 O00000 O000000 O00000 O00000 OO00000 oo oo ee ee Yo ee 00 ee oo ee Ge se ee DO 00 Ge ee ee 2 5 Rear view g ge ge ge 00 00 oo Ge oo ge oke 100 00 oo oo oo Ge 00 ee oo oo oo oo oo oo 100 100 ES oo ce T ee 2 oo ge oo ge OO 100 oo GLASS 1 LASER Gan oo ge Ge 00 oo oo oo oo oo oo KOKO 60 oo ge oo NCBIN NCBOUT ETHERNET 5 8 efo ge 9 10 11 12 13 14 15 16 E 3 9 10 11 12 13 14 15 16 5 6 7 8 ol2 The following service connectors can be found on the rear of the SL 3GHD128128 RC router if redundant supply is installed RS 232 port for external control protocols Gee oe O O cc cc O O OO Oo Ss oo aa OO DO gt gt o SES OO DO gt gt oo CO TI m Ben i 0 D ss oo ana RS 232 Network Control Bus Input The protocol of this bus is described in a separate manual 10 100Base T Ethernet bus for external router control Ethernet NCB IN Network Control Bus Output NCB OUT Sync Loop Synchronization signal in out Black amp Burst composite tri level sync reference input with passive loop through for vertical interval switching Configurations switch See Chapter 3 for further descriptions Config
13. 28 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD3296 RC 32x96 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD9632 RC 96x32 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD64 RC 64x64 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD3264 RC 32x64 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD6432 RC 64x32 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD32 RC 32x32 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL UPG 32IN Upgrade to add 32x Inputs to your partly configured SL 3GHD128128 RC router SL UPG 320UT Upgrade to add 32x Outputs to your partly configured SL 3GHD128128 RC router SL UPG 32IN OUT Upgrade to add 32x Inputs and Outputs to your partly configured SL 3G
14. 4 and higher Use your Nevion Configurator to verify the HW revision of your Sublime unit 2 Untitled project System Configurator Network Electronics ASA File View Tools Windows Help Ci 5 Wl Cose 2 Refresh IP Settings it Levels ii Vitual Router Mappings G3 Categories Salvos E Button Configurations Project Explorer Name a Info E Controllers Status Hostname IP address Subnet mask Default gateway TCP connections Sublime type Firmware Bootloader i Gyda c 10 10 13 100 255 255 240 0 10 10 10 254 CAA ETHCON CP DIP 2 104 SE 10 10 13 101 255 255 240 0 70 10 10 254 None vi router CP CP DIP 15 202 2 0 1pre1 EE 10 10 13 102 255 255 240 0 10 10 10 254 None BT video router CP DIP 10 1 0 4 Sublime J 148 255 255 240 0 10 10 10 254 JGS ETHCON 1 CP DIP 14 105 Sublime J 255 255 240 0 10 10 10 254 JGS ETHCON e CP DIP 14 105 JG Sublime J F 2 d 10 10 10 254 None ave 32 ports data router DIP 13 203 20 1pre1 2 Sublime ref HD3232 R CP 10 10 11 130 2 10 10 10 254 None ss 32x32 hd router CP CP DIP 4 203 203pre3 2 w2 Sublime SL SD0808 N CP i921681 10 192 168 1 1 None ve 8x8 sd router CP DIP 2 105 105 GEZ Sublime THOR SL 8XY CP 10 10 1223 10 10 10 254 10 10 10 216 CP DEA 103 KE Sublime aza gpio 10 10 13 27 10 10 10 254 asa ethcon scil CP DIP 0 2 04pre1 2 0 3 EJ THOR SL 8XY CP Sublime ar ponm Right click the c
15. HD128128 RC router Power Supply Unit SL PWR 300 300W AC Power Supply Unit for Sublime 128 range 48VDC output nevion com 7 SL 3GHD128128 RC 2 Specifications 2 1 Mechanics Dimensions Router weight Router weight optical I O Max Power consumption Power consumption optical I O Safety Emission standards 2 2 Power supply SL PWR 300 AC Supply voltage range AC Mains connector DC output DC connector Status monitoring Safety standards 2 3 Control Standard Features Serial port Connector NCB ports Connectors 2 Ethernet port Connector Reclocker option Input Equalizer option Synchronization Connector s Rev A HxWxD 355x483x50 100 mm 19 8RU 7 75 kg including 1x PSU module 1 15 kg Each 16x16 Optical l O module weighs 0 20kg without SFPs Each SFP weighs typically 17 59 48V 2 8A 135W Without Optical I O Each 16x16 Optical I O module with SFPs inserted consumes maximum 20W typically 7W in addition to above specification Compliant with CE EN55103 1 and 2 300 W Power supply Unit 90 130VAC 180 254VAC switchable 50 60Hz 300W IEC 320 48V max 6 25A Maximum 300 W DSUB 2V2P Via LED in front of the router Compliant with CE EN60950 UL 1950 CSA22 2 RS 232 for protocol conversion to VikinX compact control protocol or to third party protocols DEQ D sub 9 pin female For integration with VikinX compact router c
16. NEVISAN SL 3GHD128128 RC VikinX Sublime 128x128 3G HD SD SDI Router User manual Rev A SL 3GHD128128 RC Rev A Nevion Support Nevion Europe Nevion USA P O Box 1020 1600 Emerson Avenue 3204 Sandefjord Norway Oxnard CA 93033 USA Support phone 1 47 33 48 99 97 Toll free North America 866 515 0811 Support phone 2 47 90 60 99 99 Outside North America 1 805 247 8560 E mail support nevion com See http www nevion com support for service hours for customer support globally Revision history Current revision of this document is the uppermost in the table below Rev Repl Date Sign Change description A 0 2013 07 18 JGS Updated chapter 5 2 with supported network modes 0 2012 02 20 NBS AAA First release nevion com 2 SL 3GHD128128 RC Rev A Contents Revision history eege 2 Re lte 5 TAL Ge e VANANIS EE 6 2 Specification San eian Seege Ee 8 e Een Ge 8 2 2 POWer SUPPIV saka kose re kk kre aks l cc en pl e kn pt kn m E BASSE 8 2 3 COMM Ol REH 8 2 4 Video SPECIFICATIONS ENEE 8 2 5 ROR EE 10 2 5 POWER SUP OI MOU Uses cna ceca n f tens ka ka bn bak cn freden ens Acne Rede bad gates neve dae enya oe 11 2 52 Sena port DIMOU ee oka ek dad bo dede a foke De deeg 11 g Gonfg ratlo EE 12 3 1 Power Supply SOLID DEE 12 eur 12 3 3 Router MOE e s ks oeil ed kan wa a dan e eene dee kann geen ee deed 13 3 4 External power alarm WEE 14 BEE EE re IN de
17. contain battery backed memory devices nevion com 30 SL 3GHD128128 RC Rev A Appendix B Additional Protocol information B 1 Leitch Pass Through protocol This protocol is available in Sublime firmware 2 4 0 and later The Sublime implementation of Leitch Pass Through supports all commands described in Leitch Routing Switchers Serial Protocol Reference Edition E In the command Alarms Status Request a bit field is used for reporting active alarms In Sublime the bit field is used as in the table below Bit Description Reported from firmware version 0 Power A failed 2 4 0 1 Power B failed 2 4 0 2 Positive power too low 2 4 0 3 Negative power too high 2 4 0 4 Client TCP IP connection failed 2 4 0 5 No valid product key 2 4 0 6 SFP error 2 4 0 7 EXT IN not locked 2 5 4 8 EXT IN CRC error counting 2 5 4 9 Fan error 2 6 2 B 2 Grass Valley Native protocol This protocol is available in Sublime firmware 2 5 4 and later Sublime does not support all commands available in this protocol The supported commands are described in the table below Command Parameter Comments BK Background E Echo BK E and BK E ON and BK E OFF are Activities all accepted and will be responded with ER 00 BK R Protocol Processor Will be responded with KB R lt firmware Software Revision version gt TJ Request Each command supports only one X Tak
18. e Index With point Level Bitmap TI Request The optional level Index is not supported Take Index With The command can only be used to Level Index switch all levels QH Query AC Query active Sublime has defined the alarms defined alarm status alarm status in the table below All active alarms will be responded on this request Alarm Alarm Name Alarm ID Parameter 0x0101 Frame Fan Fan number 0x0105 Power supply 01 Power A failed 02 Power B failed 0x010A Positive power Always 00 too low nevion com 31 SL 3GHD128128 RC Rev A 0x010B Negative Always 00 power to high 0x010C Client TCP IP Always 00 connection failed 0x010D No valid Always 00 product key 0x010E SFP error Always 00 Ox010F EXT IN not Always 00 locked 0x0110 EXT INCRC Always 00 error counting QN Query Names L Level IS Sources with source indexes On SL D32P the next available source will be labeled DISCONNECT and used to disconnect destinations ID Destinations with destination indexes nevion com 32
19. ents for Nevion equipment 1 The equipment will meet the guaranteed performance specification under the following environmental conditions Operating room temperature range 0 C to 45 C Operating relative humidity range lt 95 non condensing 2 The equipment will operate without damage under the following environmental conditions Temperature range 10 C to 55 C Relative humidity range lt 95 non condensing nevion com 27 SL 3GHD128128 RC Rev A Product Warranty The warranty terms and conditions for the product s covered by this manual follow the General Sales Conditions by Nevion which are available on the company web site www nevion com nevion com 28 SL 3GHD128128 RC Rev A Important notes regarding Software in the VikinX Sublime router family range This product utilizes software components that are licensed with open source licenses The source code for these components and our modifications are available from http labs nevion com open source OpenTCP includes software developed by Viola systems http www violasystems com nevion com 29 SL 3GHD128128 RC Rev A Appendix A Materials declaration and recycling information A 1 Materials declaration For product sold into China after 1st March 2007 we comply with the Administrative Measure on the Control of Pollution by Electronic Information Products In the first stage of this legislation content of six hazardous material
20. herefore counted as 1 router in the limitations 1 and 2 above From limitations 1 and 2 above the resulting Ethernet configuration may consist of maximum 8 devices 4 routers and 4 control panels with the exceptions mentioned above An example is illustrated in the figure below nevion com 21 SL 3GHD128128 RC Rev A System Configurator Physical connections Control lines Ethernet lines KN Deen WEB ONI EH E Mi K WS SZ Ech No ae w Fi 5 9 Va N port W ent Ca Ethemet DE4x2 ANEN TAN gh eh Switch N l DN ser ase o gt SL r outer sti 64x1 AG4x64 d v 32x32 AG4G4 Sy X y pe 5 AVI ZxI2 ADG Z632 Figure 1 Ethernet connections and configuration Refer to the Nevion Configurator User Manual for further information about the above described configuration connection options 5 3 NCB connection Via the Network Control Bus system several routers and control panels can be interconnected Up to 16 levels of routers or combinations of routers can be controlled The NCB system and all RS 232 ports interchange the system status This means that any control system either from Nevion or from a third party manufacturer connected to any RS 232 port in the NCB loop will have access to all communication data on the bus 5 3 1 Connecting control panels To get a control panel working with a specific router configure the control panel to the same level as the router Several panels ca
21. loss Signal format Signal level Field selectivity Rev A EN50083 9 SMPTE 297 2006 18dBm OdBm gt 1dBm 1260 1620nm 9 125um single mode LC UPC FP laser 0 to 5dBm typ 2dBm 1310nm 20nm 9 125um single mode LC UPC BNC IEC 61169 8 75 Ohm gt 15dB 5 MHz 1 485 GHz gt 10dB 1 5 3 GHz Automatic up to 70m 2 97Gbps typical Belden 1694A Automatic up to 100m 1 485Gbps typical Belden 1694A Automatic up to 300m 270Mbps typical Belden 8281 BNC IEC 61169 8 75 Ohm gt 15dB 5 MHz 1 485 GHz gt 10dB 1 5 3 GHz 800mVp p 10 20 80 SD limit 0 4ns 1 5ns lt 0 5ns rise fall variation HD limit 270ps lt 100ps rise fall variation 3G limit lt 135ps lt 50ps rise fall variation lt 10 Non inverting electrical with respect to inputs SD lt 0 2 Ul 3G HD lt 1 UI SD lt 0 2 Ul 3G HD lt 0 2 UI 1 75 ohm BNC female loop thru gt 40dB 100 kHz 5 MHz gt 35dB 5 10 MHz NTSC or PAL Black amp Burst or HD Tri Level according to SMPTE 274M SMPTE 276M Nominal 1 0Vp p Field 1 nevion com 9 Rev A SL 3GHD128128 RC HD Tri Level 1280x720 within clock intervals 148 5 MHz 455 780 line 7 Timing range HD Tri Level 1920x1080 within clock intervals 148 5 MHz 625 1070 line 7 O O00000 O000000 O00000 O000000 O00
22. n be configured to control the same router Panels can also be connected to a router via the RS 232 interface Please refer to your control panel manual for installation 5 3 2 Pin out and cable type VikinX Sublime routers and Control Panels use RJ45 connectors for the Network Control Bus ports The following pin out is used Pin 1 Not Connected Pin 2 Not Connected eg T 128 Pin 3 Data retour m TH Pin 4 Data Green Blue 45 Pin 5 Data Pair3 N Pair 1 4 Pin 6 Data retour ES Pin 7 Not Connected SEE T E Pin 8 Not Connected a i The following connection example shows connection of 4 VikinX devices with RJ45 connectors and bus termination nevion com 22 SL 3GHD128128 RC Rev A Figure 2 NCB loop configuration Note that each device at the end of the chain has a termination plug indicated with the letter T This termination plug must be inserted in the correct connection port If not no NCB communication is possible 5 3 3 Termination plug The termination plug that is mentioned in the previous chapter is necessary when you want to avoid closing the loop be a long cable nevion com 23 SL 3GHD128128 RC Rev A The termination plug is a standard RJ45 plug with the following internal wiring Figure 3 NCB loop termination plug As seen in the figure above Pin 3 is connected to Pin 4 and Pin 5is connected to Pin 6 5 3 4 Control bus structure The Network Control Bus st
23. olumn headers and select the appropriate column to be shown if you don t see the appropriate column in your default display For further information about FW releases please go to the Nevion web site to download or check available FW releases www nevion com 3 8 Configuring Input options This configuration is done in the Nevion Configurator 3 8 1 Input EQ It is possible to enable or bypass Input EQ for each router input separately Default is Input EQ enabled nevion com 16 SL 3GHD128128 RC Rev A 3 9 Configuring Output options This configuration is done in the Nevion Configurator Sublime router settings BAX Inputs Outputs Output Reclocker Slew rate Slew rate Laser Laser alarm Laser temp ty mode enabled alarm 1 Enabled Auto HD vw ON Ok lv OK v 2 Enabled Le Auto HD iM ON OK lv OK v 3 Enabled Auto HD MON wi OK w OK v 4 Enabled Lal Auto HD ON OK lv OK v 5 Enabled Auto HD ON v OK lv OK v 6 Enabled wl Auto vw HD MON vK v OK v 7 Enabled Auto HD MON wi OK v OK v 8 Enabled se 1 Auto sei HD ON Ok Lv OK v 3 Enabled el Auto HD SON vi OK Lv OK v 10 Enabled Auto HD la ON wi OK e OK vi 11 Enabled Auto sei HD l ON vi OK v OK v 12 Enabled sl Auto sei HD SON vi OK lv OK v 13 Enabled m Auto HD l ON zw Ok ae OK v 14 Enabled Auto HD iM ON v OK l OK v 15 Enabled Auto HD MON y OK lv OK v 16
24. onfiguration RJ45 1 In 1 Out 10 100BaseT Ethernet bus for external router control RJ45 Bypass of reclocking from system controller Bypass of input equalization from system controller Analog Black amp Burst looped Both PAL and NTSC supported S Tri Level Looped For HD signal formats only Distribution of synchronization signals between several routers BNC 2 4 Video specifications Supported formats Telecom Broadcast Supported standards SD SDI 270Mbps HD SDI 1 485Gbps 3G SDI 2 97Gbps STM 1e and E4 270Mbps 2 97Gbps 2K 2048x1556 23 98 and 24 SMPTE 259M SMPTE 292 2008 SMPTE 424M 1 Frame depth is 50mm without optical I O with Optical I O frame depth is 100mm nevion com 8 SL 3GHD128128 RC DVB ASI Fiber transmission Optical signal inputs Sensitivity Detector overload threshold Detector damage threshold Optical wavelength Transmission circuit fiber Connectors Optical signal outputs Light source Optical power Optical center wavelength Max wavelength variation Transmission circuit fiber Connectors Electrical signal inputs Connectors Impedance Return loss Cable equalization Electrical signal outputs Connector Impedance Return loss Signal level Rise fall time Amplitude overshoot Signal polarity Signal transition Timing jitter Alignment jitter Reference inputs Number of inputs Connector Return
25. rs may be turned off for support of E4 STM 1e TCP IP RS 232 and NCB control interfaces Hot pluggable optics on variants with optical I O Software based Configurator for easy system set up Ultra Slim frame depth Low Power consumption high reliability design Redundant power supply system with front indicators Interoperability with existing VikinX routers Future proof and flexible product range VikinX Sublime provides many of the powerful control features that drove the VikinX Modular range to success VikinX Sublime is ideal for general purpose facilities on air routing mobile outside broadcast applications and sophisticated A V applications VikinX Sublime router series provides most important 3rd party control interfaces allowing the control of our routers through 3rd party management software This enables you to utilize existing routers and management systems from other manufacturers and still draw the advantages of implementing VikinX Sublime in your routing application nevion com 5 SL 3GHD128128 RC Rev A 1 1 Product variants There are a number of variants for this product They all share the same hardware and are distinguished by FW keys Item Description SL 3GHD128128 RC 128x128 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD128128 RC 16OPT 128x128 HD SDI Router Multira
26. ructure follows the standard MIDI bus definition The NCB is defined as a closed chain of units This means that the NCB OUT of the last unit must be connected to the NCB IN of the first unit in the NCB chain To avoid problems with the control of VikinX units the installer user has to assure that the bus structure is installed according to this definition The total number of VikinX devices in an NCB chain is limited to 50 5 3 5 Maximum distance between NCB devices The standard MIDI definition allows a maximum cable length of 200 250 meters between two devices Longer distances can be made with MIDI repeater units To avoid grounding problems all NCB ports have opto coupled inputs nevion com 24 Rev A SL 3GHD128128 RC This chapter is only applicable for routers that have electrical I O for parts of the Optical I O starts from I O 1 and up in blocks of 16 I O available video I O video I O All video inputs are terminated with 750hm See also Chapters 2 4 and 2 5 for The SL 3GHD128128 RC router offers standard 75Ohm BNC connectors for electrical more details The ee below shows the I O numbering This means that routers with both electrical and optical I O always start with all the optical Sublime Optical offers dual SFPs with LC UPC connectors for optical video I O I O first followed by the electrical I O 6 Connecting signal cables to the router 6 1 Optical interface 6 2 Electrical interface nevion
27. s 12us after vertical sync on the synchronization signal This will occur in line 1 on all video formats This is useful when you have different video formats on the same router also with different frame rate This setting is not according to recommendations in SMPTE RP 168 2002 Embedded data may become damaged or lost 3 7 Configuring protocol options For various reasons Nevion has decided to make it possible to turn the extra commands that were added to the NCB protocol when we introduced the Sublime router range either off or on At the same time the user must select whether he she shall use the RS 232 port for controlling the router or the Ethernet port This is done in order to prevent both ports from simultaneously being applied for controlling the router There is a new Protocol field in the Nevion Configurator where you may choose from the following options NCB without Sublime ext RS232 This is the old Compact NCB protocol without Sublime extensions If used on a Sublime it also disables the Ethernet port of that device NCB RS232 This is the regular Sublime protocol with the extra commands that were added to the NCB protocol If used on a Sublime it also disables the Ethernet port of that device This is the default option for the Sublime SL range of products This protocol is similar to the Triton protocol allowing users to connect the Sublime device to a Jupiter VM 3000 System Controller
28. s has to be declared The table below shows the required information Toxic or hazardous substances and elements RE a R ACMA SRK SS ER Part Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated Pb Hg Cd Chromium biphenyls diphenyl ethers Cr VI PBB PBDE SL 3GHD128128 RC O O O O O O SL PWR 300 O O O O O O O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ T11363 2006 X Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ T11363 2006 This is indicated by the product marking A 2 Recycling information Nevion provides assistance to customers and recyclers through our web site http www nevion com Please contact Nevion s Customer Support for assistance with recycling if this site does not show the information you require Where it is not possible to return the product to Nevion or its agents for recycling the following general information may be of assistance Before attempting disassembly ensure the product is completely disconnected from power and signal connections All major parts are marked or labeled to show their material content Depending on the date of manufacture this product may contain lead in solder Some circuit boards may
29. s valid from VikinX Sublime firmware 2 6 3 and newer Changing the ethernet setup on a VikinX Sublime must be done with the Nevion Configurator version 4 4 0 or newer All VikinX Sublime routers and IP based Control Panels are connected together through an Ethernet Switch A VikinX Sublime device has only one physical Ethernet connection If redundant control is required this limitation has to be solved by the control system For Ethernet protocol details concerning this router please refer to the following manual Modular Router Control Protocol This manual can be found on our web site http www nevion com 5 2 1 HW limitations The user has the option of connecting more than two devices together without having a Multicon to control the network However unless you apply a Multicon as a system controller the limitations that apply are 1 One Sublime control panel may connect to a maximum of 4 Sublime routers 2 One Sublime router may be controlled by a maximum of 4 Sublime control panels Exceptions to the above limitations A router with a local CP e g SL V6464 CP may only connect to 1 other router Both routers must be configured with the same address and be of different type A V Example 1x SL V6464 CP may only control itself 1x Audio router AA or AES Both routers must be configured with the same address 16x2 routers that are expanded to NNx2 are using the NCB bus for this purpose The total NNx2 router is t
30. te 270Mbps 2 970Gbps Specs as for SL 3GHD128128 RC but with 16 Optical I O and 112 Electrical I O SL 3GHD128128 RC 320PT 128x128 HD SDI Router Multirate 270Mbps 2 970Gbps Specs as for SL 3GHD128128 RC but with 32 Optical I O and 96 Electrical I O SL 3GHD128128 RC 48OPT 128x128 HD SDI Router Multirate 270Mbps 2 970Gbps Specs as for SL 3GHD128128 RC but with 48 Optical I O and 80 Electrical I O SL 3GHD128128 RC 64OPT 128x128 HD SDI Router Multirate 270Mbps 2 970Gbps Specs as for SL 3GHD128128 RC but with 64 Optical I O and 64 Electrical I O SL 3GHD128128 RC 800PT 128x128 HD SDI Router Multirate 270Mbps 2 970Gbps Specs as for SL 3GHD128128 RC but with 80 Optical I O and 48 Electrical I O SL 3GHD128128 RC 96OPT 128x128 HD SDI Router Multirate 270Mbps 2 970Gbps Specs as for SL 3GHD128128 RC but with 96 Optical I O and 32 Electrical I O SL 3GHD128128 RC 112OPT 128x128 HD SDI Router Multirate 270Mbps 2 970Gbps Specs as for SL 3GHD128128 RC but with 112 Optical I O and 16 Electrical I O SL 3GHD128128 RC 1280PT 128x128 HD SDI Router Multirate 270Mbps 2 970Gbps Specs as for SL 3GHD128128 RC but with 128 Optical I O SL 3GHD96128 RC 96x128 HD SDI Router Multi rate 270Mbps 2 970Gbps Supports 3G SDI HD SDI SD SDI DVB ASI Upgradeable to 128x128 Ethernet RS 232 NCB control 19 8RU depth 5cm SL 3GHD12896 RC 128x96 HD SDI Router Multi rate 270Mbps 2
31. ter 2 layers Layer 1 Input Layer 1 Output 1 1 1 1 2 2 2 2 3 3 3 3 64 64 64 64 Layer 2 Input Layer 2 Output 1 65 1 65 2 66 2 66 3 67 3 67 64 128 64 128 3 layers Layer 1 Input Layer 1 Output 1 1 1 1 2 2 2 2 3 3 3 3 42 42 42 42 Layer 2 Input Layer 2 Output 1 43 1 43 2 44 2 44 3 45 3 45 42 84 42 84 Layer 3 Input Layer 3 Output 1 85 1 85 2 86 2 86 nevion com 13 SL 3GHD128128 RC Rev A 3 87 3 87 42 126 42 126 In Outputs 127 and 128 are not in use in this router setup 3 layers 4layers Layer 1 Input Layer 1 Output 1 1 1 1 2 2 2 2 32 32 32 32 Layer 2 Input Layer 2 Output 1 33 1 33 2 34 2 34 32 64 32 64 Layer 3 Input Layer 3 Output 1 65 1 65 2 66 2 66 32 96 32 96 Layer 4 Input Layer 4 Output 1 97 1 97 2 98 2 98 32 128 32 128 3 4 External power alarm The external power alarm can be switched according to the following pattern SW 7 Power alarm OFF Disables External Power Alarm ON Enables External Power Alarm Default setting is External Power Alarm disabled 3 5 Power up mode Switch 8 on the configuration switch defines the power up mode The sublime router provides two modes for powering up the system The power up options can be switched according to the following pattern SW 8 Power Up mode OFF Switches all outputs according to the b
32. uffered information in the routers processor system ON Switches all outputs to input 1 Default setting switches all outputs according to the buffered information in the routers processor system nevion com 14 SL 3GHD128128 RC Rev A 3 6 Configuring switching time This configuration is done in the Nevion Configurator It is possible to configure switching time in the router The settings are made through the Nevion Configurator but a description of the options is given here The user can select between three options 1 Switch according to detected sync reference signal Default Switching time is determined by the synchronization signal that feeds the router This is useful when the video signal has the same format as the synchronization signal Supported formats are PAL NTSC 750 50p 750 60p 1125 50i and 1125 60i 2 Switch according to signal format Select format Here it is possible to use one synchronization signal to switch a different video format A prerequisite is that the synchronization signal and the video signal have the same frame rate E g Use PAL as synchronization signal with a 750 50p video signal Supported formats are PAL NTSC 750 50p 750 60p 1125 50i 1125 60i 1125 50p and 1125 60p We do not support 1125 50p or 1125 60p as synchronization signal This means that our 3G HD routers cannot use default setting 3 Switch to handle mixed signal formats The router switche
33. uration Note that any VDC supplies with output voltage between 36VDC and 72 VDC with sufficient power may be applied to the router 3 The router is supplied with inverse diodes This means that in a redundant power supply application the router will pull its entire load from the PSU with the highest output voltage nevion com 10 SL 3GHD128128 RC Rev A 2 5 1 Power Supply pinout The DSUB 2V2P power pinout for Sublime routers and Control Panels are as follows Pin ff Description Socket 48VDC Pin GND a There is a switch on the right hand side of the power supply module that selects mains voltage The mains voltage can be either 110VAC or 230VAC This switch must be set in the correct position depending on the mains voltage on the router s site Failing to select correct AC mains voltage properly may damage the Power Supply Unit 2 5 2 Serial port pinout The DE9 D sub 9 pin female connectors for the serial port s of the router have the following pin out Pin RS 232 signal Not in use Tx Rx Not in use GND GND RTS CTS Do Not Connect 00 Ni gt ako Po Note that if the standard RS 232 cable specification DCE is followed a cable with Male Male or Female Female connectors at the cable ends is used for Rx Tx crossed connection and a cable with Male Female connectors at the cable ends is used for a straight
Download Pdf Manuals
Related Search