Appendix 12: User Manual
Contents
1. Infusion Pump Interface Operating Instruction Manual Design Group 23 Ruslan Boyko EE Mario Fantini ME Alexander JC Huang EE Jianzhuang Huang CoE Libo Zhu EE Faculty Advisor Dr Nikulin May 6 2007 CONTENTS INTRODUCTION STARTING THE PUMP BASIC CONTROLS DISPLAY SCREENS ERROR MESSAGES BATTERY INSTALLATION CREDITS 5 9 9 9 0 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 95 9 9 9 0 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 O 9 9 95 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 0 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 95 9 9 9 9 9 e 9 9 9 9 95 9 9 9 9 9 95 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 c 9 9 e 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 n INTRODUCTION Thank you for purchasing the TEAM23 Infusion System Your system should include the MODEL PUMP as well as the infusion user interface The following document provides directions for use This system is designed to be used in many areas of patient care Special features include e Vibrating alert e Lighted display e Voice prompts e Programmable dosages and rates e 3 Easy steps to infusion therapy Battery powered user interface for easy transportation The TEAM23 Infusion System is equipped with sensors that monitor battery levels low medication levels and changes in pressure Stain gauges2. detect changes in pressure in the infusion line that will minimize accidental free flow and stop infusion when there is air in the line The Physician Mode allows the interface to be programmed with predetermined medication dosages and flow rates to minimize accidents in operation by patients STARTING THE PUMP INFUSION PUMP SYSTEM 1 Set up your infusion PUMP system according to its instructions 2 Turn on the POWER switch for the PUMP 3 Connect the INTERFACE to the PUMP 4 Turn on the POWER switch for the INTERFACE 5 Follow the on screen instructions and refer to this manual for inromation BASIC CONTROLS INFUSION PUMP INTERFACE CONFIGURATIONS LCD SCREEN POWER Saree BUTTON Es LEFT ARROW UP ARROW C2 O O C O ARROW DOWN ARROW ENTER CANCEL SETTINGS CONTROLS Power on off Power button Run Enter Enter button Back Cancel Cancel button Highlight menu items Up Down arrows Cycle choices Left Right arrows Change settings Settings button DISPLAY SCREENS INFUSION PUMP INTERFACE SCREENS Screen Title and Contents Description amp Functionality Power On Screen Loading Group 23 Infusion Pump Interface The initial loading power on screen Idle Screen MEDI XXXXXXXXXXXXXX Sr Diameter XX XX mm Rate XX XX ml hr To Infuse XX XX ml The medication name is displayed in the first line The syringe diameter is displayed in the second line The rate of infusi
3. ication that can be edited Sr Diameter XX XX mm Rate XX XX ml hr To Infuse XX XX ml Press Up Down arrow to change values Press Left Right arrow to move cursor Press Enter button to confirm changes Press Cancel button to cancel changes ERROR MESSAGES INFUSION PUMP INTERFACE SCREENS Error Message Display Description Low Battery Check the batteries in the infusion pump interface it is low and probably needs to be replaced soon Low Medication Check the medication left in the infusion pump it is low and probably needs to be refilled soon Air in line Carefully examine the infusion tubing for air bubbles Once the air bubble is located push the air bubble out to ensure that it is not infused into the patient High Pressure Carefully examine the infusion tubing to make sure nothing is blocking the medication Loose connection Check the connection between the infusion pump and the infusion pump interface it is probably loose Unplug the connection and connect it again to ensure connectivity BATTERY INSTALLATION 1 Stop infusion and turn off power 2 Locate the battery panel and carefully remove the cover 3 Remove old battery and replace with new battery 4 Check for secure battery connection to the battery connector 5 Close the battery panel 6 Turn power on CREDITS Dr John D Enderle Editor in Chief EMB Magazine Tim O Neil Lourdes H
4. on is displayed in the third line The amount to be infused is displayed on the last line Press Enter button to start infusion Press Settings button to select new medicine Hold Settings button for more than 3 seconds to edit the settings Setting Select Select Settings Setting 1 Setting 2 Setting 3 The screen contains up to 3 medications and dosages to be selected for infusion Press Up Down arrow to highlight items Press Enter button to select medicine Press Cancel button to cancel selection Run Confirm Run Confirmation Start the infusion The screen prompts the user for confirmation Press Enter button to start infusion Enter Cancel Press Cancel button to cancel selection Infusing The screen displays infusion information Infusion In Progress To stop press Cancel Infused XX XXml Press Cancel button to stop infusion Stop Confirm Stop Confirmation Stop the infusion Enter Cancel The screen prompts the user for confirmation Press Enter button to stop infusion Press Cancel button to cancel selection Edit Settings The screen contains up to 3 medications and Edit Settings dosages to be selected for infusion gt Setting 1 Setting 2 Press Up Down arrow to highlight items Setting 3 Press Enter button to edit medicine dosages Press Cancel button to select new medicine Medicine Editing The screen contains information on one MEDI XXXXXXXXXXXXXX med
5. ospital Bioengineer Dr Vladimir Nikulin Faculty Advisor Pr Robert Sterlacci Al Dodson
Download Pdf Manuals
Related Search