Manual - GHP Group
Contents
1. cian 7 Connecting Heater to Gas Supply ii ads 8 9 Ch cking For cea ee eect esl 10 Lighting amp Shutdown Instructions iessraicnin init 10 14 Storage of Gater eros qa quisasqasa ee SE Eense 14 Maintenant iia 14 00 u ukuy A E AEEA EEE EREE E 15 Replacements Parts List 15 Exploded Parts Drawing elites 16 A kula aqa aaa sipasqa 18 WARNING FIRE BURN INHALATION AND EXPLOSION HAZARD KEEP SOLID COMBUSTIBLES SUCH AS BUILDING MATERIALS PAPER OR CARDBOARD A SAFE DISTANCE AWAY FROM THE HEATER AS RECOMMENDED BY THE INSTRUCTIONS NEVER USE THE HEATER IN SPACES WHICH DO OR MAY CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES OR PRODUCTS SUCH AS GASOLINE SOLVENTS PAINT THINNERS DUST PARTICLES OR UNKNOWN CHEMICALS CALIFORNIA PROPOSITION 65 Fuels used in gas or oil fired appliances and the products of combustion of such fuels contain chemicals known to the State of California to cause cancer birth defects or other reproductive harm This product contains chemicals including lead and lead compounds known to the State of California to cause cancer birth defects or other reproductive harm Wash hands after handling WARNING NOT FOR HOME OR RECREATIONAL VEHICLE USE NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING PROPANE TANK TOP HEATER PROPANE TANK TOP CONSTRUCTION HEATERS The heater is desig2. 11 After burner lights turn the heater regulator knob to the desired heat setting LOW e MED e el or HIGH e e e NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING PROPANE TANK TOP HEATER TURNING OFF THE HEATER 1 Tightly close propane tank valve by turning fully clockwise 2 Turn the heater regulator knob to the OFF O position Wait at least 30 minutes for the heater to cool before handling heater 3 Always remove the heater from the propane tank after each use and store indoors Do not store heater while attached to propane tank Do not store propane cylinders in a building garage or any other enclosed area VENTILATION Always be sure to supply proper ventilation while operating this heater Provide a minimum of 1 5 square feet 0 14 opening for fresh air supply OPERATION LIGHTING INSTRUCTIONS FOR PIEZO IGNITION MODELS Read and understand all safety information before operating heater damage injury or death Read the installation operating and maintenance instructions WARNING Improper installation alteration service or maintenance can cause property thoroughly before installing or servicing this equipment Do not cover air inlet holes in mixing tube WARNING Make sure there is no open flame in the area Fully open the propane tank valve NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING PROPANE TANK TOP HEATER LIGHTING INSTRUCTIONS FOR PIEZO IGNITION MODELS CO
3. Damage caused by misuse or use contrary to the owners manual and safety guidelines Damage caused by a lack of normal maintenance Fuses Use of non standard parts or accessories Damage caused in transit Freight charges on warranty parts or heaters to and from the factory shall be the responsibility of the owner UA ON This warranty does not imply or assume any responsibility for consequential damages that may result from the use misuse or the lack of routine maintenance of this heating appliance A cleaning fee and the cost of parts may be charged for appliance failures resulting from lack of maintenance This warranty does not cover claims which do not involve defective workmanship or materials FAILURE TO PERFORM GENERAL MAINTENANCE INCLUDING CLEANING WILL VOID THIS WARRANTY THIS LIMITED WARRANTY IS GIVEN TO THE PURCHASER IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE THE REMEDY PROVIDED IN THIS WARRANTY IS EXCLUSIVE AND IS GRANTED IN LIEU OF ALL OTHER REMEDIES IN NO EVENT WILL GHP GROUP INC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you CLAIMS HAND
4. any gas or oil burning appliance Always remove the heater from the propane tank after each use and store indoors Do not store heater while attached to propane tank Do not store propane cylinders in a building garage or any other enclosed area The tank must be disconnected and stored outdoors in a well ventilated area out of reach of children in accordance with the standard for the the Storage and Handling of Liquefied Petroleum Gases ANSI NFPA 58 and CSA B149 1 Natural Gas and Propane Installation Code The plastic tank valve plug supplied with your tank must be tightly installed when the tank is disconnected from the heater MAINTENANCE INSTRUCTIONS 1 Turn unit off allow heater to fully cool and disconnect propane hose before performing any Maintenance functions 2 Keep unit clean and keep the inside of the unit debris free 3 Have unit checked by a qualified technician at least once a year preferably prior to the heating season NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING 14 PROPANE TANK TOP HEATER TROUBLESHOOTING Unit will not light Valve on propane cylinder not open Open cylinder valve by turning counterclockwise Propane cylinder empty Have cylinder refilled Regulator not in Low position Turn regulator to Low position Excess flow device triggered Close cylider valve wait 5 minutes and reopen slowly Defective Regulator Replace Regulator assembly Burner will not stay
5. ATCH 40 000 10 8 Hrs High TT360PDG PIEZO 40 000 10 8 Hrs High 52 5cm NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING PROPANE TANK TOP HEATER GENERAL SAFETY INSTRUCTIONS Accidents are always tragic especially because so many of them could have been prevented with a little care and judgment There are some basic good practices we hope you will follow for safe use of your heater IMPORTANT SAFETY INFORMATION e Children should be carefully supervised when they are in the area Always maintain proper clearance from combustible materials Minimum clearance from combustibles Sides 36 91cm 48 122cm Floor 0 when installed on 20lb cylinder Note Not for use on finished floor e Heater must be placed on level and stable surface e Never place anything including clothes or other flammable items on the heater The appliance area shall be kept clear and free from combustible materials gasoline and other flammable vapours and liquids Do not modify or operate a heater which has been modified e Adequate clearance for accessibility and for combustion amp ventilation air supply must be maintained at all times when the heater is operating e Service and repair should be done by a qualified service person The heater should be inspected before each use and at least annually by a qualified person More frequent cleaning may be required as necessary Do not service while hot or operat
6. LED AS FOLLOWS 1 Contact your retailer and explain the problem 2 Ifthe retailer is unable to resolve the problem contact our Customer Service Dept detailing the heater model the problem and proof of date of purchase 3 Arepresentative will contact you DO NOT RETURN THE HEATER TO GHP GROUP INC unless instructed by our Representative This warranty gives you specific legal rights and you may also have other rights which vary from state to state a E TO REGISTER THE WARRANTY ON YOUR HEATER PLEASE FILL OUT THIS CARD COMPLETELY AND MAIL WITHIN 14 DAYS FROM DATE OF PURCHASE OR REGISTER ON LINE www ghpgroupinc com Name PHONE EMAIL ADDRESS CITY STATE ZIP MODEL SERIAL DATE PURCHASED DEALER PURCHASED FROM TYPE OF STORE CITY amp STATE WHERE PURCHASED PRICE PAID Please Take a Minute To Give Us Your Answers To The Following Questions All Responses Are Used Solely For Market Research And Are Held In Strict Confidence Who primarily decided this purchase O Male Female 0 18 24 O 25 39 1140 59 60 and over Purpose of Purchase Do you own any other portable heaters L Yes No If yes type brand How do you intend to use your new heater L Construction Site 1 Farm Warehouse Commercial L Garage Outbuilding O Other How did you become aware of this heater 1 In Store Display L NewspaperAd Magazine Ad L Friend Relati
7. NTINUED Stop Read all safety information first 2 Turn heater regulator knob counterclockwise 4 to OFF position WARNING Stand to the side of unit while lighting Do not stand or have any part of your body over or near the heater while lighting Slowly open cylinder valve by turning counterclockwise Wait five 5 minutes to clear out any gas Then smell for gas including near the floor If you smell gas STOP Follow the safety information on the tag attached to the heater If you do not smell gas go to the next step Turn heater regulator knob clockwise to LOW e position Press in safety shut off valve plunger Fig 3 With safety shut off valve plunger pressed in immediately push down and release piezo ignitor button repeatedly This will light the burner Mesh screen on burner glows red when lit Once the burner is lit continue to depress the valve plunger for 30 seconds and then release Be careful not to shake the heater when releasing the plunger If burner does not light within 10 seconds turn regulator knob to the OFF O position Wait at least five 5 minutes for gas to dissipate before relighting If burner goes out repeat steps 5 through 7 or use a match If heater will not light after repeated attempts do not attempt to repair heater Return heater to near est authorized service center or to the address on the back of this manual freight prepaid When burner is lit turn heater r
8. PROPANE TANK TOP CONSTRUCTION HEATER USER S MANUAL AND OPERATING INSTRUCTIONS MODELS TT360L TT360PL TT360H TT360PH TT360DG TT360PDG TT360DGP TT360PDGP TT360DGD TT360PDGD SR C US ANS Z83 7 2011 CSA 2 14 2011 Adequate ventilation must be provided A GHP Group Inc W 6440 W Howard St la Niles IL 60714 3302 A GENERAL HAZARD WARNING FAILURE TO COMPLY WITH THE PRECAUTIONS AND INSTRUCTIONS PROVIDED WITH THIS HEATER CAN RESULT IN DEATH SERIOUS BODILY INJURY AND PROPERTY LOSS OR DAMAGE FROM THE HAZARDS OF FIRE EXPLOSION BURN ASPHYXIATION CARBON MONOXIDE POISONING AND OR ELECTRICAL SHOCK ONLY PERSONS WHO CAN UNDERSTAND AND FOLLOW THE INSTRUCTIONS SHOULD USE OR SERVICE THIS HEATER IF YOU NEED ASSISTANCE OR HEATER INFORMATION SUCH AS AN INSTRUCTION MANUAL LABELS ETCETERA CONTACT THE MANUFACTURER CONSUMER Retain this manual for future reference Questions problems missing parts Before returning to your retailer call our customer service department at 877 447 4768 8 30 a m 4 30 pm CST Monday Friday or email us at customerservice ghpgroupinc com www ghpgroupinc com Printed in China IMTT360DG GAU TABLE OF CONTENTS General Safety Information units osito 3 4 A e o PE E E O 3 Product Features aussi 4 Heater Assembly cdas 5 Wiring escripta ua a a Qa aa 6 Propane Salty A E o e e e A 7 Refilling The Propane Gas Tank
9. R LEAVE THE HEATER UNATTENDED WHILE BURNING 15 PROPANE TANK TOP HEATER REPLACEMENT PARTS ILLUSTRATION NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING THIS PAGE INTENTIONALLY LEFT BLANK WARRANTY LIMITED WARRANTY This limited warranty is extended to the original retail purchaser of this Forced Air Convection Radiant Heater and warrants against any defect in materials and workmanship for a period of one 1 year from the date of retail sale GHP Group Inc at it s option will either provide replacement parts or replace or repair the unit when properly returned to the retailer where purchased or one of our service centers as directed by GHP Group Inc within one 1 year of retail purchase Shipping costs labour costs etc are the responsibility of the purchaser DUTIES OF THE OWNER This heating appliance must be operated in accordance with the written instructions furnished with this heater This warranty shall not excuse the owner from properly maintaining this heater in accordance with the written instructions furnished with this heater A bill of sale canceled check or payment record must be kept to verify purchase date and establish warranty period Original carton should be kept in case of warranty return of unit WHAT IS NOT COVERED Damage resulting from use of improper fuel
10. egulator knob to desired heat setting LOW e MED e el or HIGH e e e TURNING OFF THE HEATER 1 Tightly close propane tank valve by fully turning clockwise A 2 Turn the heater regulator knob to the OFF O position Wait at least 30 minutes for the heater to cool before handling heater 3 Always remove the heater from the propane tank after each use and store indoors Do not store heater while attached to propane tank Do not store propane cylinders in a building garage or any other enclosed area VENTILATION Always be sure to supply proper ventilation while operating this heater Provide a minimum of 1 5 square feet 0 14m opening for fresh air supply NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING 13 PROPANE TANK TOP HEATER LIGHTING IN WINDY AREAS When using this heater indoors where there is wind it will be necessary to use a match or long stem butane lighter to ignite the burner It may be difficult to keep the match lit long enough under windy conditions Follow the Lighting instructions when Using a Match procedure after doing the following 1 Position the heater and cylinder such that the Thermocouple is opposite the direction that the wind is coming from 2 Position your body behind the heater such that your body blocks the wind while you are following the instructions for lighting with a match STORAGE Never store a Propane gas tank inside a building or in the vicinity of
11. erclockwise 4 Wait five 5 minutes to clear out any gas Then smell for Ignition Hole gas including near the floor If you smell gas STOP Safety Shutt of valve Fis NTE ac levi Follow the safety information on the tag attached to the Inlet Connector heater If you do not smell any gas go to the next step Mounting Bat Knob Eli et Propane Tank Valve Heat Regulator Knob 5 Turn heater regulator knob clockwise to the LOW e position Fig 3 Handwheel lighting Do not stand or have any part of your WARNING Stand to the side of unit while body over or near the heater while lighting 6 Locate ignition hole in bottom reflector of the burner Fig 3 Insert a lit match through ignition hole A CAUTION Do not insert match into air inlet holes in mixing tube 7 Push in the safety shut off valve plunger Fig 3 Do not push safety shut off valve plunger before inserting lit match 8 Once the burner is lit continue to depress the valve plunger for 30 seconds and then release Be careful not to shake the heater when releasing the plunger 9 If the burner does not light within 10 seconds turn regulator knob to the OFF O position Wait at least five 5 minutes for the gas to dissipate before relighting 10 If heater will not light after repeated tries do not attempt to repair heater Return heater to nearest authorized service center or to the address on back of this manual freight prepaid
12. fied Petroleum Gases ANSI NFPA 58 and the Natural and Propane Installation Code CSA B149 1 The minimum clearances to combustible construction Sides 36 91cm Top 48 122cm Floor combustible must be maintained at all times Not for use on finished floors The hose assembly should be visually inspected prior to each use of the heater If it is evident that there is excessive abrasion or wear or the hose is cut it must be replaced prior to the heater being put into operation The replacement hose assembly shall be that specified by the manufacturer wass Never use an open flame to check for leaks OPERATION LIGHTING INSTRUCTIONS WHEN USING MATCH Read and understand all safety information before operating heater damage injury or death Read the installation operating and maintenance instructions WARNING Improper installation alteration service or maintenance can cause property thoroughly before installing or servicing this equipment WARNING Do not cover air inlet holes in mixing tube WARNING Make sure there is no open flame in the area Fully open the propane tank valve NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING 10 PROPANE TANK TOP HEATER LIGHTING INSTRUCTIONS WHEN USING MATCH CONTINUED 1 STOP Read all safety information first FIGURE 3 2 Turn heater regulator knob counterclockwise to OFF O position 3 Slowly Open Cylinder valve by turning count
13. h the vapor space of the tank An arrangement of vapor withdrawal The propane LP gas pressure regulator and hose assembly supplied with the heater must be used without alteration The hose assembly shall be visually inspected prior to each use of the heater If it is evident that there is excessive abrasion or wear or the hose is cut it must be replaced prior to the heater being put into operation The replacement hose assembly shall be that specified by the manufacturer REFILLING THE PROPANE GAS TANK ALL NEW CYLINDERS MUST BE PURGED BEFORE THE FIRST FILLING Turn heater gas valve knob and gas tank valve to OFF position Propane tank valve equipped with the old style fitting has LEFT HANDED THREADS Turn POL fitting CLOCKWISE to loosen Protect POL fitting when disconnected from tank e Have tank filled by your local Propane gas supplier Some propane tanks have a bleed off valve This valve should be inspected for leaks after each filling of the tank Turn clockwise to close the valve e Fasten full Propane tank and connect POL fitting to tank valve by turning COUNTERCLOCKWISE e With heater gas valve knob still in the OFF position turn ON tank valve and check for leaks with soap solution Propane is safe to use when properly handled Careless handling of the Propane gas tank could result in fire and or an explosion Therefore e Always keep tank cylinder securely fastened in an upright position Avoid tipping
14. ing e Never connect heater to an unregulated gas supply The heater is shipped from the factory for LP Propane gas This heater is for use with propane gas only do not convert heater to any other gas Installation must conform to local codes or in the absence of local codes with the standard for the Storage and Handling of Liquefied Petroleum Gases ANSI NFPA 58 and the Natural Gas and Propane Installation Code CSA B149 1 e The minimum and maximum inlet pressures to the regulator from the gas tank are 17 5 psi and bottle pressure respectively Use only the regulator amp hose assembly provided with the heater Inspect the regulator hose assembly prior to each use of the heater If there is excessive abrasion or wear or hose is cut replace with regulator nose assembly listed on the parts list prior to using this heater e Gas supply connections should be checked using a 50 50 solution of liquid dish soap and never use a flame to check for gas leaks e Do not restrict inlet or outlet by any means The flow of combustion and ventilation air is not to be obstructed e This heater should not be directed toward any propane gas container within 20 ft 6M The heater must be located at least 6 ft 1 83 m in the U S or ii 10 ft 3 m in Canada from any other propane gas container e The propane cylinder supply system must be arranged to provide for vapour withdrawal from the operating cylinder PRODUCT FEATURES e Portable 8 Stable e Ad
15. justable Input Ratings e Match or Piezo Electric Spark Ignition e 360 Degree Heat Radius e 100 Safety Shutoff System NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING PROPANE TANK TOP HEATER TT360 SERIES HEATER ASSEMBLY Tools Required Estimated Assembly Time Contents Phillips head screwdriver 5 minutes Tank Top Heater 1 Tank Collar Bracket 1 M4x8 Machine Screws 2 DUAL BURNER MODEL The tank collar bracket must be assembled before the heaters can be attached to the propane tank 1 Align bolt holes in tank collar bracket with bolt holes in mounting plate on heater 2 Drive in two machine screws supplied into the bolt holes attaching tank collar bracket to mounting plate on heater Fig 1 FIGURE 1 Mounting Plate heat Regulator Knob NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING PROPANE TANK TOP HEATER WIRING DIAGRAM ELECTRODE black PIEZO IGNITER Piezo models only NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING PROPANE TANK TOP HEATER PROPANE SUPPLY This heater requires a 20 lb propane cylinder for operation Not included The propane LP gas tank must also be equipped with the following A collar to protect the propane gas valve A shutoff valve terminating a Propane gas cylinder valve outlet as specified in the American National Standard for Compressed Gas Cylinder Valve Outlet and Inlet Connections A safety relief valve having direct communications wit
16. lit when Tilt switch open Correct alignment of unit to ensure it is vertical gas valve plunger released Wiring of thermocouple Check wiring connections are properly engaged Defective thermocouple Replace thermocouple Defective tilt switch Replace tilt switch Defective gas valve Replace gas valve assembly Excessive flames coming out Debris or spider webs in mixing tube Clean burner tube with bottle brush rinse in water of burner not glowing red or burner and drain thoroughly before reinstalling Clogged orifice Remove and clean using compressed air Piezo won t spark 1 Defective piezo 1 Replace Piezo Some models only 2 Ignitor misaligned with burner mesh 2 Realign ignitor with burner mesh The spark gap 3 Wire frayed or damaged should be 0 15 4mm Replace wire Flames flashback burn inside Debris or spider webs in mixing tube Clean burner tube with bottle brush rinse in water the mixing tube and drain thoroughly before reintsalling Clogged orifice Remove and clean using compressed air REPLACEMENT PARTS LIST DESCRIPTION PART NUMBER G Regulator Assembly R 121 DHI Piezo Ignitor L 007 Valve Cable HEEE SI SIS 5 2 8 aj ae 2 o O O O O N 6 Thermocouple o O LLE T360C 05 T360C 00 T360C 03 T360C 09 513 T360C 07 T30C 3 T360C 06 7150 07 of a 33 Oy NEVE
17. ned and approved for use as a construction heater under ANSI Z83 7 CSA 2 14 It is hard to anticipate every use which may be made of this heater CHECK WITH YOUR LOCAL FIRE SAFETY AUTHORITY IF YOU HAVE QUESTIONS ABOUT APPLICATIONS Other standards govern the use of fuel gases and heat producing products in specific applications Your local authority can advise you about these IMPORTANT READ THIS USER S MANUAL CAREFULLY AND COMPLETELY BEFORE TRYING TO OPERATE OR SERVICE THIS HEATER IMPROPER USE OF THIS HEATER CAN CAUSE SERIOUS INJURY OR DEATH FROM FIRE EXPLOSION AND CARBON MONOXIDE POISONING This is a direct fired tank top construction heater for indoor construction use only The heater must be placed where it is NOT directly exposed to water spray rain and or dripping water lts intended use is primarily the temporary heating of buildings or structures under construction alteration or repair All the products of combustion generated by the heater are released into the area being heated This heater operates at approximately 98 combustion efficiency but still produces a small amount of carbon monoxide Humans can tolerate small amounts of carbon monoxide for short periods Carbon monoxide can build up in a heated space and failure to provide adequate ventilation could result in poisoning or death SPECIFICATIONS OPERATING IGNITION MODEL e BTU OUTPUT high TIME 20 b TYPE 5 cylinder TT360L MATCH 40 000 10 8 Hrs High TT360DG M
18. tank on its side when connected to a regulator since this may cause damage to diaphragm in regulator e Handle valves with care Never connect an unregulated Propane tank to construction heater e Do not subject Propane tank to excessive heat Tightly close the gas shutoff valve on the Propane tank after each use The POL fitting must be protected when disconnected from the propane tank e Never store a Propane gas tank inside a building or in the vicinity of any gas burning appliance THE DISCONNECTED TANK MUST NEVER BE STORED IN A BUILDING GARAGE OR ANY OTHER ENCLOSED AREA NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING PROPANE TANK TOP HEATER CONNECTING HEATER TO PROPANE TANK Read and understand all safety information before connecting heater to propane tank 1 Place heater onto tank with tank collar bracket over tank collar Fig 2 Mounting bolt knob should be positioned to the outside of tank collar and be positioned as closely as possible directly opposite to the cylinder valve outlet See Figures 1 and 2 2 Firmly secure to tank by hand tightening mountingbolt knob Do not overtighten mounting bolt knob 3 Make sure heater regulator knob is in the OFF O position 4 Insert regulator s connector into tank s valve outlet fitting and turn left counterclock wise until fully tightened Threads are left handed Figure 2 NOTE Heater features a hand wheel that can be used to tighten the fitting to
19. the cylinder No wrench is required but may be used if desired NOTE The vertical stem of this heater must be installed in the vertical position This heater is equipped with a safety shutoff switch in the event that the heater is tipped over during operation The heater may fail to remain lit if the vertical stem is not installed vertically 5 Open propane tank valve slowly by turning counterclockwise 6 Check all fittings for leaks Apply a 50 50 mixture of liquid soap and water to all joints Bubbles forming show a leak Correct all leaks at once A WARNING NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS 7 Always remove heater from propane cylinder after each use Do not store heater while attached to propane tank NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING PROPANE TANK TOP HEATER CONNECTING HEATER TO PROPANE TANK FIGURE 2 Thermocouple Electrode Ignition Hole Safety Shutt off valve Piezo NOTE some models only Mounting Bolt Knob Handwheel NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING PROPANE TANK TOP HEATER CHECKING FOR LEAKS Check all gas connections with a 50 50 soap and water solution to be sure they are tight and leak proof The formation of bubbles indicate a gas leak Correct all leaks before using the heater The installation of your heater must meet all local codes and or gas utility requirements or in the absence of local codes with the Storage and Handling of Lique
20. ve O TV Commercial 0 Store Salesperson L Other What made you select this heater L Style Size Portability Price Package Brand Other Do you own rent Would you recommend this heater to a friend Yes Please give us your comments THANK YOU FOR COMPLETING THIS FORM Information will be held confidential WARRANTY REGISTRATION IMPORTANT We urge you to fill out your warranty registration card within fourteen 14 days of date of purchase You can also register your warranty on the internet at www ghpgroupinc com Complete the entire serial number Retain this portion of the card for your records GHP Group Inc 6440 W Howard St Niles IL 60714 3302 Tel 877 447 4768 www ghpgroupinc com SAVE THIS CARD Place Postage Stamp Here GHP Group Inc 6440 W Howard St Niles IL 60714 3302
Download Pdf Manuals
Related Search