1 HEADING 1
Contents
1. Zone 32 Zone 33 Zone 34 Zone 35 Zone 36 Zone 37 NX 148E User manual Zone 42 Zone 43 Zone 44 Zone 45 Zone 46 Zone 47 Zone 48 Zone 49 Zone 50 Zone 51 Zone 52 Zone 53 Zone 54 Zone 55 Zone 56 Zone 57 Zone 58 Zone 59 Zone 60 Zone 61 Zone 62 Zone 63 Zone 64 Zone 65 Zone 66 Zone 67 Zone 68 Zone 69 Zone 70 Zone 71 Zone 72 Zone 73 Zone 74 Zone 75 Zone 76 Zone 77 Zone 78 Zone 83 Zone 84 Zone 85 Zone 86 Zone 87 Zone 88 Zone 89 Zone 90 Zone 91 Zone 92 Zone 93 Zone 94 Zone 95 Zone 96 Zone 97 Zone 98 Zone 99 Zone 100 Zone 101 Zone 102 Zone 103 Zone 104 Zone 105 Zone 106 Zone 107 Zone 108 Zone 109 Zone 110 Zone 111 Zone 112 Zone 113 Zone 114 Zone 115 Zone 116 Zone 117 Zone 118 Zone 119 Page 28 23 04 05 Metuno Zone 38 Zone 39 Zone 40 Zone 41 Zone 124 Zone 125 Zone 126 Zone 127 Zone 128 Zone 129 Zone 130 Zone 131 Zone 132 Zone 133 Zone 134 Zone 135 Zone 136 Zone 137 Zone 138 Zone 139 Zone 140 Zone 141 Zone 142 Zone 143 Zone 144 Zone 145 Zone 146 NX 148E User manual A r Y Zone 79 Zone 82. Test Bell and or communicator test while system is in disarmed condition Re exit Re Exit The exit delay has been re started without disarming the system Output Trip Output Trip A trip has occurred on an expander auxiliary output Data Lost Data Lost Communication of a signal has failed log only event Walk test Walk Test A zone Walk Test mode has been activated End Test End Test Test has been ended Cross Trip Cross Trip The first zone of a cross zone has been tripped log only Expansion Expansion Event An expansion module created an undefined event Event Partial Arm Partial Arm Reports a closing in the stay mode Listen In Listen In A listen in function has been activated Service Start Service Start Technician is on site Service End Service End Technician is off site Code Entry Code Entry A code has been entered First Open First Open Reports when the first partition is disarmed NX 148E User manual Page 26 23 04 05 Networ 7 DISPLAY DESCRIPTION Last Close Last Close Reports when the last partition is armed Sprnklr Sprinkler Instant sprinkler supervisory report Clock Set Clock Set Clock has been reset RF Jammed RF Jammed A wireless expansion module is jammed CleanMe CleanMe Asmoke detector requires cleaning IMPORTANT These reference tables on the following pages need to be completed by your installer Keep these tables in a safe place Installing Service Company Add
3. key while that zone is displayed Step 4 When finished press the key to return to the code entry screen NOTE All zones will automatically be unbypassed each time the system is disarmed Group bypass Step 1 Press the BYPASS key Step 2 When the LCD prompts for a code optional if programmed enter your user code Step 3 The bypass light flashes Step 4 Press 0J 0 Step 5 Press the BYPASS key again Step 6 The bypass light will stop flashing and will illuminate Step 7 Pressing the A y scroll keys will display all bypassed zones Press the key to exit this viewing mode NOTE All zones will automatically be unbypassed each time the system is disarmed NX 148E User manual Page 11 23 04 05 Networ Unbypassing Step 1 Press the BYPASS key Step 2 When the LCD prompts for a code optional if programmed enter your user code Step 3 The bypass light flashes Step 4 Enter the zone number each time 2 digits of the zonels that must be unbypassed Example to bypass zones 4 en 5 press 0 4 0 5 Step 5 Press the BYPASS key again Step 6 The bypass light will stop flashing NOTE All zones will automatically be unbypassed each time the system is disarmed NX 148E User manual Page 12 23 04 05 A Networ Y ADDING AND CHANGING USER CODES Your system must be Disarmed to add change user codes Step 1 Press k 5 Step 2 Enter a Master Arm Disarm Code NOTE For partitioned system
4. manual Page 22 23 04 05 A Networ Y KEYPAD CONTROL TONES BEEPS A sounder is built into the keypad and may sound for any of the following reasons e Beeps for all keypresses e Sounds a continuous tone during the Entry delay time e Pulses when a day zone is violated while the system is disarmed e Pulses when a FIRE zone has a trouble condition e Pulses when the armed status changes and the AC power is off e Beeps 3 times for trying to arm with the READY light off if FORCE ARMING has not been selected e Beeps 1 second for the CHIME feature e Beeps 1 second at the end of the exit delay e Beeps to indicate telephone line fault if selected e Beeps during an exit delay beeps rapidly for the last 10 seconds of an exit delay if selected e Pulses when one or more of the following conditions are detected Zone or Box Tamper Low Battery AC Power Fail or Expander trouble e Beeps 3 times every minute indicating a low battery or missing transmitter is detected if wireless device is in system Entering code will suppress the sounder for 12 hours Entering a valid code will silence the keypad sounder when it is pulsing The arm disarm state of your system will not change when entering a code to silence a pulsing keypad sounder Please contact your installer if a trouble condition exists NX 148E User manual Page 23 23 04 05 Sy GS Pdetruasao SERVICE DISPLAY The following message will be displaye
5. proficient in its operation All users of your security system should read and follow the instructions in this booklet and if possible practice on the keypad control while your professional installer is on site Failure to do so could result in the security system not working properly Please keep this booklet in an accessible location for the life of the security system If you do not understand any part of this manual you should notify your installing company The SECURITY CONTROL PANEL can be turned on ARMED and off DISARMED by entering a 4 or 6 digit code into the keypad control which is similar to a telephone keypad If your security control panel has been so programmed you may be able to turn on ARM your system by simply pressing the STAY or EXIT key The system must always be disarmed using a 4 or 6 digit code The LCD keypad includes 9 lights and a 32 character liquid crystal display and a built in electronic sounder These provide specific information relating to the status of the security system which is described in the booklet Understanding what the lights and sounds mean will help you to easily operate your system Keep in mind the level of security you will obtain with this system relates specifically with two major factors 1 The quantity quality and placement of security devices attached to this system 2 The knowledge you have of the security system and how that knowledge is utilized in a weekly test of the complete
6. silence the keypad Wait a few minutes and repeat step 2 to attempt another reset If the keypad still beeps after repeated attempts please contact your installer Reading the event log The control panel has an event log that can be retrieved using a master code This log contains a listing of the events along with date time and partition where the event occurred An overview of possible events can be found in Appendix A of this manual Step 1 To view the log press 9 0 The LCD screen will prompt you for a code Step 2 Enter your master code The LCD screen will now show the most recent event Step 3 To view the events from most recent to the oldest press the Y down scroll key Step 4 To view the events from the oldest to the newest press the A up scroll key The display contains the following information Event Open 75 gt User or Zone ID Date 9 25 17 57 P3 gt Indicates partition Month Day and indicates an ATime shown in event not reported 24 hour format This screen shows an opening of Partition 3 on September 25th at 5 27 p m by user 75 The x shows that this event is not programmed to be reported to the central monitoring station NX 148E User manual Page 18 23 04 05 Networ Adjusting the view brightness of the LCD Step 1 Enter sk 9 1 The LCD Screen will prompt for a code Step 2 Enter master code The LCD will now prompt you to raise or lower the view Step 3 Using the sk 9 1
7. 0 Zone 81 Zone 82 Zone 147 Zone 148 Zone 149 Zone 150 Zone 151 Zone 152 Zone 153 Zone 154 Zone 155 Zone 156 Zone 157 Zone 158 Zone 159 Zone 160 Zone 161 Zone 162 Zone 163 Zone 164 Zone 165 Zone 166 Zone 167 Zone 168 Zone 169 Page 29 Zone 120 Zone 121 Zone 122 Zone 123 Zone 170 Zone 171 Zone 172 Zone 173 Zone 174 Zone 175 Zone 176 Zone 177 Zone 178 Zone 179 Zone 180 Zone 181 Zone 182 Zone 183 Zone 184 Zone 185 Zone 186 Zone 187 Zone 188 Zone 189 Zone 190 Zone 191 Zone 192 23 04 05 www gesecurity net EMEA Distribution is a division of GE Security EMEA bvba COPYRIGHT 2005 GE Security EMEA bvba All rights reserved GE Security EMEA bvba grants the right to reprint this manual for internal use only GE Security EMEA bvba reserves the right to change information without notice
8. 678 This display is reflecting all 8 areas are Ready and Area 5 is 12345678 disarmed NOTE If a number is flashing on the armed line that area is armed Instant If a number is flashing on the ready line that area is ready to be Force Armed System Ready If ALL areas are disarmed and ready to arm this display will Type code to arm appear on the LCD screen ARMING AND DISARMING MULTIPLE PARTITIONS Ready To arm disarm multiple partitions enter a code that has arm disarm authority for ALL of the partitions to be armed disarmed The following display will appear on the LCD screen 12 45 78 Disarm gt The numbers on the top line represent the disarmed areas Seer Peet E Arm gt to which this code has access The numbers on the bottom line represent the areas that are armed Refer to the following table for possible conditions LCD DISPLAY FOR AREA TOP LINE OVER BOTTOM LINE CONDITION sue Area Not used or Authorized Blank Dash Dash Area Not Ready Flashing Area Dash Area Ready to Force Arm Dash Flashing Area Area Armed Instant Area Dash Area Disarmed amp Ready to Arm Dash Area Area is Armed e Todisarm all of these areas press the A up scroll key e Toarmall of these areas press the w down scroll key e Totoggle a single area between the armed and disarmed conditions press Area number For example If Area 4 is armed x 4 will disarm Area 4 If Ar
9. Networx Series NX 148E LCD keypad User manual TABLE OF CONTENTS tcticissssscesccesccosucescsesessessesssnsacesesescassectsucssaceancsseseacssesaestsestssesectsucssadausdenasasessieesesteestassasesssecksucdsucsaeceaaceaese gt 2 INTRODUCTION siii dias 4 GLOSSARY OF TERMS a a A 5 KEYPAD DISPLAY amp LED sisscciscsccisacesccssccsaxcesesesacecesecsdesesesesnsastescesesesncoaaseassesesecssnsestcsdesesesssssessoesssncesecaesesasesesbessucectssasesteeseseesd 6 UNDERSTANDING THE LIGA TS uta cea ia ance ted alot Rectan etal ee ach ii metals tiem oes Ancients eo ata 6 EMERGENCY ACTIVATION KEYS IN 7 KEYPAD FUNCTION isis iia didas 8 ARMING YOUR SYSTEM IN THE AWAY MODE uuscsscsssesscesccsscsscsssssssssssscssessecsssssesssessssssssssssessssssssussssssssssessessussussssessessssssssecsussasssessessssasesscssssessussseeasenss 8 MAKING THE SYSTEM READY TAR a e dote ero ey Do 8 ARMING YOUR SYSTEMIUN THE STAY MODE ritos a aii aa A ARGS 9 USING THE QUICK ARM OPTIONAL CHANGING MODES WHILE SYSTEM ARMED cc aaa DISARMINGTH ES VS LEM Sara ena et a Che aa Nt veda ll nossa th pase Meat teeta De cal iNet E E o CANCEL ABORT FEATURE OPTIONAL BYPASSING ZONES on o esa ses us me nee ao a Re 0 eater e ee de SS e Catena GROUP BYPASS Sisin esa a e ad UNE PAIN namen a a aa a e ADDING AND CHANGING USER CODES rigningen gerne enn SS SAPAN ESSES a 13 ASSIGNING USER CODE AUTHORITY LEVELS oooooocnocaciconnnnnocncocnnncnncncnononocncnonono
10. Step 1 Step 2 Step 3 Setting the Step 1 Step 2 Step 3 Step 4 Enter the x key followed by the A key The LCD Screen will display the zone status Use the up and down scroll keys Al w to browse through the descriptions The LCD Screen will display the list of all zones in sequential order by zone number Press to exit this function keypad tone Press the ak key followed by the 0 key Keypad is now in the Adjust Tone mode Raise tone gt PS Press the A up scroll key located on the right Venere Re gt side of the display to make the keypad sounder go to higher tones Press the vw down scroll key to make the keypad sounder adjust to lower tones When the desired tone is reached press the key to set this tone and exit from the Adjust Tone mode View alarm memory Step 1 Step 2 Step 3 Press the x followed by the 3 key to display the zone s on the keypad that created the last alarm Ena The LCD Screen will display the zone description ZONEN for those zones Press to exit the alarm memory Programming phone numbers optional If private reporting voice or siren tone is enabled up to 3 phone numbers can be programmed or changed A telephone number towards a central monitoring station cannot be changed or reviewed Step 1 Step 2 Step 3 Disarm the system if it is not already disarmed Press the ak key followed by 4 1 to program chan
11. area Perimeter The outer edge of the protected area Quick Arm An option that allows you to turn on ARM the security system by pressing either the STAY or EXIT key on the keypad control for ARMING only as programmed by the installing company User Code A four 4 or six 6 digit entry code used to arm or disarm the system NX 148E User manual Page 5 23 04 05 Networ a KEYPAD DISPLAY LED s Understanding the lights Fire Light Ready Light Armed Light O 3 Programmable _ ER am elas 000 Numeric code entry keys The appropriate Poltica stickers should be mr applied on the door of your keypad for the Emergency Activation keys that are programmed to work with your system Armed Light Bypass Light Cancel Light Chime Light NX 148E User manual Up amp down scroll keys Power Light e mm oo 5 function keys To Arm or Disarm Enter your user code To Quick Arm and Stay Press Stay key To Quick Arm and Exit Press Exit key Door Chime Press Chime key to activate Reset Smoke Detector Press 7 the door is detachable and can be removed or replaced when desired Installation Com EMERGENCY pany ACTIVATION KEYS PRESS and HOLD for 2 seconds Monitoring Center The armed light is on when the system is armed The armed light is off when it is disarmed The armed ligh
12. astercode the screen will display the message walktest mode Step 3 Activate all sensors to be tested Each activation of a sensor is confirmed with a ding dong sound The zonetexts of the sensors who have reacted are displayed one by one on the screen Step 4 Enter a Mastercode to exit the walktest mode NX 148E User manual Page 19 23 04 05 Netwo P Y PARTITIONED SYSTEMS OPERATION This system is A multi partitioned A not partitioned If your system is multi partitioned and the keypad resides in one partition your keypad will provide the status of the zones in your partitioning by using the screen messages described earlier in this manual The Master Mode of operation if programmed by your installer allows you to access any partitioning providing your code is authorized within the system and perform functions in other partitions NOTE 1 will temporarily access the Master Mode The keypad will revert back to its assigned partition 60 seconds after a keypress or 10 seconds without a keypress Read the following paragraphs to help you understand the different screen messages that will be displayed from your keypad Lights in partitioning master mode e ARMED will illuminate if ALL partitions are armed e READY will illuminate if ALL partitions are Ready The ready light will flash if all areas are Ready or Force armable e FIRE will illuminate if ANY one area has a Fire condition The fire light wi
13. cnononononacnonononacnonononecnonononeroonrnonocacnonononacurnonone 14 OTHER KEYPAD FUNCTION So acne 15 RAN VIEW ZONE STATUS SEMING TAE KEYPAD TON Enano a OD ra SEN dr ALM ro RST AA Sat aah ah AU A Sie saad be 16 VIEW ALARM MEMO ted ARNE 16 PROGRAMMING PHONE NUMBERS OPTION A ci tada 16 TEST FUNCIONO ONU acen EO ER 17 EAS SS 17 LIGHT CONTROL FOR X LO DEVICES OPTIONAL a o a a iaa i 17 CHANGE LANGUAGES anina decia Odo ese LE a e A E ios AY aae Aa itn Sn tl e 18 DETECTOR RESED FUNCTION sc o e aos 18 READING THEEVENT LOG E RN 18 ADJUSTING THE VIEW BRIGHTNESS OF THE LOD cinc ans 19 SETT TUR VAN A A RR EAN 19 PARTITIONED SYSTEMS OPERATION iia 20 LIGA TSIN PARTITIONING MASTER MODES Sant Lado A dE tester Da Aon SSP toate 20 DISBLAVS IN PARTITONING MASTER MODE nt e Esther EE 21 KEYPAD CONTROL TONES BEEPS lt ciscsi ccisssincasssadonsdasaleondvasduedivendonsduesieetsdnsineaiesstonsdvadbagndonsdnedbvenlosaciesbessCdnauesteesdossineotestisesies 23 SERVICE DISPLAY firs swiss ciessacsoxescacvcvcocedheostcostcvsnebensnstehensxcoacdansdchencoskcbstcvetausteosesbeesncbokedcucbanenaa ebeb ehcowkcbsacustebsbubsssbesancdeadbassacedeess 24 NX 148E User manual Page 2 23 04 05 Networ APPENDIX A EVENT LOG APPENDIX B REFERENCE TABLES NX 148E User manual Page 3 23 04 05 A Networ Y INTRODUCTION This manual is furnished to help you understand your security system and become
14. d periodically if the security system requires service Call your service provider promptly if this message is observed Service Required Type 2 for help Control Over current Control Siren trouble Box tamper Control Phone trouble Oo 3 x s Control Fail to Comm Control Ground fault Control Loss of time Control Power trouble Control Low Battery Expansion Over current Expansion Power trouble Com gt m lt 2 X o os Qa 5 2 a 2 oN do 30 os 3 gt Do E ae 2 NX 148E User manual If you see this display press x followed by the 2 key One or more of the following fault messages will be displayed Use the A V scroll keys to browse through them To exit the service messages press t A short circuit of a control s power supply has occurred Open circuit has occurred on the bell or siren circuit The Box Tamper circuit has activated The phone line connected to the control is not operating properly The control attempted to communicate a message to the Central Station but was unsuccessful A short to ground has been detected on a control circuit Your system has lost total power and needs the clock reset The main power to your system is not on The standby battery is low A short circuit of an expansion devices power supply has occurred An auxiliary reporting device has failed to communicate The main power to an expansion power suppl
15. ea 4 is disarmed xX 4 will arm it e Press STAY during the exit delay to bypass all interior zones in the exit delay e To control the individual areas refer to the following section NX 148E User manual Page 21 23 04 05 Networ OPERATING INDIVIDUAL AREAS IN THE MULTI PARTITION MODE Enter a code that is a valid arm disarm code for the area you wish to operate The following display will appear on the LCD screen 12 4 78 Disarm gt Only the areas authorized by this code will appear 3 56 Arm gt To toggle between the armed and disarmed states of an individual area press x Area number To operate an individual area enter the number of the partition you wish to operate The LCD keypad will now operate as a single area keypad All keys and functions entered will affect this individual partition only The lights and display represent the status of that partition only The word System will be replaced with the word Area The following is an example of this feature To exit this screen press Area 5 Ready MG is ani and DE 5 is ae arm To exit the Type code to arm individual partition moae enter SILENCING ALARMS IN THE MULTI PARTITION MODE If the keypad is sounding an alarm or the siren is running it can be silenced by entering a code with the authority for the areals that are in alarm NOTE The EXIT BYPASS and STAY keys will only work if an individual partition is selected NX 148E User
16. ed omit Step 3 e When Auto Instant is enabled if you do not leave through a designated entry exit door the display will read Instant indicating that the entry exit doors no longer have an entry delay If Auto Instant is enabled omit Step 4 Step 3 Press the STAY key e The bypass light will illuminate indicating that designated interior zone s are bypassed All interior devices will bypass automatically giving the user freedom of movement within the interior area e The stay light will also illuminate NOTE Normally all entry exit doors are delayed Step 4 To toggle from a delayed entry mode to Instant mode press the STAY key again The LCD display will read Instant meaning System Armed the entry exit doors do NOT have an entry delay Instant Using the Quick Arm optional The Quick Arm feature may be used if it is enabled Quick Arm will allow the user to arm the security system in the AWAY mode by pressing the EXIT key or arm in the STAY mode by pressing the STAY key This feature is used for ARMING ONLY and will not disarm the security system This is ideal for a maid or baby sitter code etc NX 148E User manual Page 9 23 04 05 Networ Y Changing modes while system armed Step 1 Pressing the STAY key will turn on off toggle a delay on Entry Exit doors and turn on off toggle the INSTANT message Step 2 Optional only possible if bypass toggle option has bee
17. ess NOTE The abort feature must be enabled Entering a code followed by the CANCEL key during or after an alarm report to the central station will cause the cancel light to come on It will stay on until the central station has received the cancel report NOTE The cancel feature must be enabled NX 148E User manual Page 10 23 04 05 Networ Bypassing zones If you wish to bypass one or more zones this must be done while the system is in the disarmed state To bypass zones two procedures are possible Procedure 1 If you know the number of the zone to bypass use the following steps Step 1 Press the BYPASS key Step 2 When the LCD prompts for a code optional if programmed enter your user code Step 3 The bypass light flashes Step 4 Enter the zone number each time 2 digits of the zonels that must be bypassed Example to bypass zones 4 en 5 press 0 4 0 5 Step 5 Press the BYPASS key again Step 6 The bypass light will stop flashing and will illuminate Step 7 Pressing the A vw scroll keys will display all bypassed zones Press the key to exit this viewing mode Procedure 2 If you do not know the number of the zone you wish to bypass use the following steps Step 1 Press A The description for zone 1 will be displayed Step 2 Use the A w scroll keys to browse through the custom descriptions for the zones in this system Step 3 To bypass or unbypass a specific zone press the BYPASS
18. evices optional This menu allows you to control up to ten X 10 devices from each keypad Step 1 Press ak 4 5 The LCD screen will prompt you to Select Light Number 0 9 Step 2 Enter the number of the X 10 device you want to control The LCD screen will show the light number on the left On the right side of the display it will prompt you to turn the light X 10 device On or Off Step 3 Press the Vv key to turn the X 10 device On or press the A keyt o turn the X 10 device off Step 4 The LCD screen will again prompt you to Select Light Number 0 9 Step 5 Repeat Steps 2 and 3 until complete Step 6 Press the key to exit from the X 10 menu NX 148E User manual Page 17 23 04 05 Networ Change languages This function allows you to switch between the two languages programmed in your keypad NOTE You must exit any other function mode before attempting to change languages Step 1 Press ak 4 9 The LCD display switches to the other language Step 2 To switch back to the other language only step 1 has to be repeated Detector reset function This function is used to reset Smoke Detectors and Zone Troubles Your system must be Disarmed to use the Reset function Step 1 Press 7 Resets have now been performed The FIRE light will go off if the smoke detectors have been reset Step 2 If the keypad begins beeping the reset did not execute properly Enter your code to
19. g an alarm to the monitoring center Check with your installing company to determine how your security system will respond to the Panic Hold Up activation NX 148E User manual Page 7 23 04 05 Networ KEYPAD FUNCTIONS Arming your system in the AWAY mode AWAY is utilized when the user is going away from the premise and wants the interior protected Listed below are the steps to arm in the AWAY Mode Step 1 Close all protected doors and windows e Ready light will be on or flashing when all protected System Ready zones and sensors are secure NOTE If any zones are Type Code to Arm bypassed a sensor in that zone can be violated without affecting the ready light e The security system will not arm if the ready light is off System Not Ready Refer to Making the System Ready to Arm below For help press gt e lf the power light is off you have no AC power Restore power if possible If not contact your installing company If the power light if flashing you have a battery failure Contact your installing company Step 2 Enter your 4 or 6 digit user code to arm the system e The armed and exit lights will illuminate System Armed e You may now leave the building All Zones Secure IMPORTANT The exit light will flash rapidly for the last 10 seconds of the exit delay as a warning to the user that the exit time is about to expire The user may wish to disarm and rearm the system if more time is needed Making the sys
20. ge telephone number 1 4 2 to program change telephone number 2 4 3 to program change telephone number 3 The LCD display will prompt you for a code Enter a master code If the number cannot be changed the keypad sounder will produde 3 short beeps NX 148E User manual Page 16 23 04 05 Networ Step 4 The LCD display will prompt you for a new phone number Enter phone num Enter the phone number EEEEEEEEEEEEEEEE Note empty location are shown as a E In order to delete a number you just program all E s This is done with the bypass key with the key the cursor can be shifted to the right without changing the telephone number Step 5 When finished press the key to leave this program mode Test function optional If programmed this function will perform a battery test communicator test and or a siren test Step 1 Press 9 4 4 The test will be performed as programmed Step 2 If the siren test is performed enter a user code to silence the siren No alarms will be sent and no reports will be sent unless a communicator test is performed at which time a test signal will be sent Display test The keyboard also provides a testfuntion by the means of which the LCD display and all LED s are tested Step 1 Press ak 4 5 The test will be performed and all of the LCD pixels and LED indicators will flash Step 2 Press the key to leave the display test Light control for X 10 D
21. have access Step 3 Enter the 2 digit applies to NX4 6 8 or 3 digit applies to NX8E user number Always use leading zeros when necessary i e 004 for user number 4 Step 4 The LCD will now prompt you for the attributes in the following chart PROMPT Ea Outputs used DO NOT CHANGE THIS SEGMENT Open Close Rprt Bypass enable These are for use by a professional installer only Arm Disarm Master code Sched arm only Arm only Reserved Output 4 Output 3 Output 2 Output 1 0 No 1 Yes Your keypress will apply to the user code you entered in Step 3 If these messages appear on the LCD screen press the x key until you return to the prompt for the user code or until you exit this adjust mode Step 5 NOTE The LCD will now display all of the partitions to which this user has access If you wish to remove a partition press the partition number on the keypad and the display will mark that partition with a hyphen indicating access has been removed If you wish to re establish user access to the partition press the partition number again Step 6 Press k to save the data The LCD will then prompt you for the next user code Step 7 If another user code needs to be programmed return to Step 3 If not press to exit this feature without saving the data NX 148E User manual Page 14 23 04 05 Ry Networ Y OTHER KEYPAD FUNCTIONS User menu The LCD keypads displays have a bilingual u
22. is not ready to arm because of a zone s being faulted Stay Light The stay light is illuminated when all interior zones are bypassed Instant Message The LCD display will read Instant when the entry exit door s have no delay See Arming System in Stay Mode The doors can be changed from instant to delay toggled by pressing the STAY key when the system is armed EMERGENCY ACTIVATION KEYS 4 3 Fire Auxiliary Emergency Police NOTES You must hold these keys for 2 seconds to activate these functions Your system may not be programmed for these activation keys You should press these keys only in an emergency situation that requires response by emergency personnel If your system is programmed for these functions the following reports can be sent Fire Key This key can activate the fire alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be sent to that center Auxiliary Emergency Key This key can activate the auxiliary alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be sent to that center Police Panic Hold Up Key This key can sound a local audible alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be transmitted to that center NOTE Some Panic Hold Up alarms are programmed to be silent at the protected site while reportin
23. ivated Aux 2 Auxiliary 2 Keypad Medical has been activated Panic Panic Keypad Panic has been activated KP Tamper Keypad Tamper The keypad tamper has been activated BoxTamp Box Tamper The box tamper circuit has been activated AC Fail AC Fail AC failure has been detected OverCur Over Current A short circuit of a power supply has occurred Srn Tamp Siren Tamper A siren or speaker tamper has been detected Tel Fit Telephone Fault A telephone fault or tamper has been detected Exp Trb Expansion Trouble An expansion device or keypad is not reporting to the control Log Full Log Full The event log is full Old events will be pushed out as new ones enter the log Open Open Reports user number date time and partition of opening Close Close Reports user number date time and partition of closing Exit Err Exit Error Entry Exit zone was faulted at the instant the exit delay expired Rec Close Recent Close An alarm occurred within 5 minutes after the control was armed Autotest Auto Test Sending a communicator test at a specified interval Start Prog Start Programming Local programming is started End Prog End Programming Local programming is ended Start Dnld Start Download Download session is started End Dnld End Download Download session is ended Cancel Cancel System is disarmed and the Cancel button was pressed within 5 minutes of an alarm Gnd Flt Ground Fault A short to ground has been detected Man Test Manual
24. ll flash if ANY area has a Fire Trouble condition e POWER will illuminate if the primary power is connected to the control panel It will flash if the system has a low standby battery condition It will be off if the primary power is absent e STAY will illuminate if ANY area has the stay light on e CHIME will illuminate if ANY partition is in the Chime mode e EXIT will illuminate if ANY area is timing an exit delay It will flash if ANY area is in the last 10 seconds of an exit delay e BYPASS will illuminate if ANY area has a zone bypassed e CANCEL will flash during an abort delay time If a code is entered followed by the CANCEL key while this light is flashing all abortable reports will stop the communication to the central station Remark the dialer abort delay time must be programmed by your installer If a code is entered followed by the CANCEL key during or after an alarm report the cancel light will illuminate and remain constant until the central station has received the cancel report Remark the cancel feature must be enabled by your installer e SOUNDER will sound if ANY area has the sounder on This includes Entry delay Exit delay Chime and Alarm NX 148E User manual Page 20 23 04 05 Networ Displays in partitioning master mode ARMED AND READY STATUS The LCD screen will display the Armed and Ready status of ALL eight 8 partitions if any or all of the areas is armed or not ready Armed 1234
25. n programmed by your installer Press the BYPASS key at this time to turn on off toggle all designated interior zones Step 3 Optional only possible if re exit option has been programmed by your installer When armed pressing the EXIT key will start the Exit delay enabling you to leave the building IMPORTANT The instant light needs to be off at this time if you plan on re entering the building otherwise you will create an alarm You may re initiate an entry exit delay by pressing the STAY key again The instant light will go out Disarming the system When you enter the protected area through one of the designated Entry Exit doors the keypad control will sound a continuous tone for the duration of the entry delay time or until you enter a valid code Type code to e Enter a valid user code Disarm e The red armed light will go off and the tone will stop The security system is now DISARMED If a valid code is not entered before the end of the entry delay an alarm will occur NOTE If the red armed light is flashing during the entry delay the alarm system has been activated in your absence Leave the building immediately and call your alarm company and or the police from a safe location CANCEL ABORT feature optional The cancel light will flash during an abort delay time If a code is entered followed by the CANCEL key while this light is flashing all abortable reports will stop the communication proc
26. ress Telephone number Name central station Telephone number central station Function codes programmed Controls function action Entry exit delay times in seconds Exit delay time Secondary Exit delay time PY Entry delay time Secondary Entry delay time This system is U is not O partitioned This system counts zones This system uses 4 U or 6 O digit user codes In order to comply to CLC TS 50131 3 all user codes must contain 6 digits NX 148E User manual Page 27 23 04 05 Netwo P Y Programmed functions Abort delay Battery test Cancel alarm Chime OOOOOOCOOCCL Change partitions LED Communicator test Keypad tamper Manual fire alarm Manual medical alarm Manual panic alarm Q Forced arming O Group bypass O Quick arm U Re Exit U Siren test O Swinger shutdown O Service Light Message enabled Whenever 30 keypresses are entered without producing a valid code the keypad will be disabled for 60 seconds Any value from 0 to 255 Zone descriptions zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Zone 9 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16 Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24 Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31
27. s someone changing the code of another person must have access to all or more partitions than the user being changed Step 3 Enter the 2 digit applies to NX4 6 8 or 3 digit applies to NX8E user number always enter 2 digit such as 0 3 for user 3 or 1 0 0 for user 100 The LCD keypad will display the current code for this user Stars k represent blanks Note To delete a user code press four times for a 4 digit code or six times for a 6 digit code the Cancel key Step 4 Enter the new four 4 or six 6 digit user code If you are changing the current code you may use the up and down scroll keys to select the digit to change and enter the correct number If it rejects the code because of duplication or such the sounder will beep 3 times Step 5 If another user code needs to be programmed return to Step 2 Step 6 Press the key while the ready light is flashing to exit the User Code Programming Mode NX 148E User manual Page 13 23 04 05 A Networ Y ASSIGNING USER CODE AUTHORITY LEVELS Assign authority levels to users by following the steps below Assign user codes before assigning authority levels Your system must be in the disarmed state to change user code authority levels Step 1 Press 6 Step 2 Enter a Master Arm Disarm Code NOTE Someone changing the authority of another person can only add or remove partition authorization for partitions to which they
28. scroll keys to the right of the LCD you can raise the text or lower the text Step 4 To advance to the Brightness option press sk The LCD will prompt you to brighten or dim the LCD lighting Step 5 Use the Al w scroll keys again to adjust to desired brightness Step 6 When completed exit by pressing sk Setting the system clock Step 1 Enter x 9 7 The LCD Screen will prompt for a code Step 2 Enter master code The time and date will be displayed with the current hour flashing Step 3 Use the A v scroll keys to select the proper hour Step 4 Enter the key to move to the minutes day of week date month and year Step 5 Repeat Steps 3 and 4 until the entire time and date are set Turning the door chime ON and OFF The door chime feature must be enabled by your installer The door chime is turned on or off by pressing the CHIME key If the chime is on the chime light will be illuminated If the chime is off the chime light will be off Each press of the CHIME key will toggle the chime feature on off and produce a momentary ding dong sound Walktest The possibility exists to do a walktest of the system This means that all zones activated during the walktest mode will activate the ding dong chime and will be filed into the memory of the control panel In this way the user can test his system completely Step 1 Enter k Chime the LCD screen will prompt you for a master code Step 2 Enter a M
29. ser s interface As a result you can simply select a user s function on the menu You can consult the menu by entering the x key To select a user s function following steps have to be performed Step 1 Enter the ak key The display will now begin scrolling through a list of functions and the corresponding numbers associated with those functions ex Select an option 90 journal Step 2 To select the option you must press the key with the number next to the option ex Consulting Log Review option 90 If you already know the option ex Log Review 90 you can immediately select the wanted option by pressing the 9 0 keys By doing this you don t have to browse through the user s menu The following list of menu selections will scroll automatically NOTE Some of the functions are not listed because they are installer level functions Each time the k key is pressed the next menu item will be displayed To exit the user s menu press the key Option Description English 1 AY Zone Review 0 Set Tone 1 Master Mode 2 Service Check 3 Alarm Memory 41 Telephone 1 42 Telephone 2 43 Telephone 3 44 Test 45 Display test 46 Light Control 49 English 2 5 User PIN 6 User Authority 7 Detector Reset 90 Log Review View Settings Set Date Time Walktest Silent Exit NX 148E User manual Page 15 23 04 05 Networ View zone status
30. system You should be aware of the following facts when preparing a safety security plan for your home business 1 Your security system is an electronic device and is subject to failure or malfunction Do not rely on it as your single source of security Your system should be tested weekly 3 Your system will not work without power 4 Warning devices will need to be loud enough wired correctly and properly placed to provide notification of an alarm event Smoke and heat detectors may not detect heat and smoke in all situations 6 Use qualified security professionals to install and maintain your security system mn 7 It may be possible to arm the security system without the backup battery connected Your periodic test should be done with AC Power removed to verify the battery is connected and adequately charged 8 Care should be taken to plug in and restrain the AC transformer after testing 9 Part of the security system uses fuses 5 AMP battery fuse transformer fuse F500 250V Please read the following information and instructions carefully before operating your security control system Classifications Security Grade 2 Environmental Class 2 Applied standards EMC EN50130 4 Environmental EN50130 5 Control and Indicating equipment CLC TS 50131 3 NX 148E User manual Page 4 23 04 05 A Networ Y GLOSSARY OF TERMS Abort Delay An option that allows a delay in reporting to the central station Authority Level The le
31. t will flash when there has been an alarm during the previous arm cycle The bypass light is on when any zone in this keypad s partition is bypassed If the bypass light is off no zones are bypassed The cancel light will flash during an abort delay time Entering a code followed by the CANCEL key during or after an alarm report to the central station will cause the cancel light to come on It will stay on until the central station has received the cancel report NOTE The cancel feature must be enabled See Cancel Abort Feature The chime light is on when the chime feature is on off otherwise Page 6 23 04 05 Networ Exit Light The exit light is on during the exit delay Please note that the light will flash during the last 10 seconds of the exit delay as a warning that the time is running out The user may want to disarm the system if the exit light is flashing in order to prevent an alarm The user may then re arm the system and exit before the delay expires Fire Light A steady fire light means a fire zone has been faulted A rapidly flashing fire light means that a fire zone is in a trouble condition Power Light The power light is on if the primary power is on The power light will flash if the system has a low battery condition Ready Light The ready light is on when the system is ready to arm and flashes if ready to force arm The ready light is off when the system
32. tem ready to arm If the ready light is not on or if it is flashing a zone is not secure To identify this zone use the scroll keys A y to the right of the display to browse through the zones that are not normal If you wish to bypass or unbypass one of these zones press the BYPASS key while that zone is being displayed When finished viewing the zones press the key to return to the code entry screen NX 148E User manual Page 8 23 04 05 Networ Arming your system in the STAY mode STAY is utilized when the user is inside the premise and wants protection around the perimeter The steps to arm in the STAY Mode are as follows Step 1 Close all protected doors and windows e Ready light must be on or flashing when all protected zones and sensors are secure NOTE If any zones are bypassed a sensor in that zone can be violated without affecting the ready light e The security system will not arm if the ready light is not on or flashing e fthe power light is off you have no AC power Restore power if possible If not contact your installing company for service If System Ready the power light is flashing you have a battery failure Contact Type Code to Arm your installing company for service Step 2 Enter your 4 or 6 digit user code Optional if programmed e f Auto Bypass is enabled all interior zones will be bypassed if you do not leave through a designated entry exit door If Auto Bypass is enabl
33. vel of access an individual has when using an alarm panel Central Station The location where alarm data is sent during an alarm report Chime Feature An option that allows the keypad to sound a ding dong whenever an entry exit door is opened Codes Can be either User Codes relating to a person or Function Codes a toggle switch to turn specific functions on off NOTE A system may have either four digit codes or six digit codes but not a mixture of the two Duress Code An option that allows a special code to be sent to the central station that indicates the alarm system is being operated under duress Forced Arming An option that allows the system to be turned on ARMED with one or more zones open A system that is ready to be force armed will flash the ready icon Note Those zones that are not ready will not create an alarm Function Code A Function Code is either a four 4 or six 6 digit code that has been programmed by the installer to operate a device Group Bypass An option that allows the user to bypass multiple zones with a single operation Instant Delay An option that allows an instant alarm condition for Entry Exit doors or grants a delay to allow someone to enter exit the building without an alarm or before entering a user code to disarm Master Code A master arm disarm code that can program other user codes Partitioned System A system divided into multiple areas in which its own user or users control each
34. y is not on An expansion power supply has a low battery Page 24 23 04 05 Expander Box tamper Expansion Trouble Expansion Siren trouble Expansion RF Jammed Zone Tamper Press Low Batt Press Lost Press Zone Trouble Press Hi NX 148E User manual A box containing an expansion device has been opened An expansion device or keypad is not reporting to the control panel Open circuit has occurred on the bell or siren circuit ofthe expander A radio receiver is being jammed Not applicable to all controls A zone is tampered Press ak to identify the tampered zone A wireless device has a low battery Press to identify the zone A wireless or multiplexed zone device is not reporting to the control Press ak to identify the zone A zone is experiencing some form of trouble probably wiring Press ak to identify the zone Page 25 23 04 05 Pdetruasao A NS APPENDIX A EVENT LOG NOTE Your system may not have all of the features listed in this table DISPLAY DESCRIPTION Txlobat Transmitter Low Battery The transmitter has a low battery ZN Lost Zone Lost A wireless or multiplexed zone device is not reporting to the control Duress Duress The control has been armed or disarmed with a Duress code Man Fire Manual Fire Keypad Fire has been act
Download Pdf Manuals
Related Search