Home

User`s Guide

Contents

1. User s Manual 17 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Installation This chapter gives step by step instructions about how to install the switch Selecting a Site for the Switch As with any electric device you should place the switch where it will not be subjected to extreme temperatures humidity or electromagnetic interference Specifically the site you select should meet the following requirements The ambient temperature should be between 40 F to 167 F 40 C to 75 The relative humidity should be less than 95 percent non condensing Surrounding electrical devices should not exceed the electromagnetic field RFC standards Make sure that the switch receives adequate ventilation Do not block the ventilation holes on each side of the switch Connecting to Power DC Terminal Block Power Input Step 1 Connect the DC power cord to the plug able terminal block on the switch and then plug it into a standard DC outlet Step 2 Disconnect the power cord if you want to shut down the switch 115200 8 n 1 Back View User s Manual 18 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Power Input Assignment 47 57VDC Power ig Power Ground Terminal Block A Earth Ground Connecting to Your Network Cable Type amp Length It is necessary to follow the cable specifications below when connect
2. Meets NEMA TS1 TS2 Environmental requirements such as temperature shock and vibration for traffic control equipment Meets EN61000 6 2 amp EN61000 6 4 EMC Generic Standard Immunity for industrial environment RS 232 console Telnet SNMP v1 amp v2c amp v3 RMON Web Browser and TFTP management Supports Command Line Interface in RS 232 console Supports 8192 MAC addresses Provides 2M bits memory buffer Supports IEEE802 3af Power over Ethernet PoE and IEEE802 3at PoE Power Sourcing Equipment PSE Supports IEEE802 3 802 3u 802 3ab 802 3z 802 3x Auto negotiation 1000Mbps full duplex 10 100Mbps full half duplex Auto MDI MDIX Provides up to two combo Gigabit ports SFP socket for Gigabit fiber optic expansion Supports digital diagnostics monitoring DDM digital optical monitoring DOM functions according to the industry standard SFF 8472 Store and forward mechanism Full wire speed forwarding rate Power Supply 47 57VDC Terminal Block power input Operating voltage and Max current consumption 0 37A 48VDC 0 32A 55VDC Power consumption 17 7W Max 40 C to 75 C 40 F to 167 F operating temperature range Tested for functional operation 40 C to 85 C 40 F to 185 F Hardened metal case User s Manual 3 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Console Configuration Connect to the switch console Connect the DB9 straigh
3. switch_a 2 Usage Use logout command to exit from the Exec mode or Privileged Exec mode 3 Command Syntax logout 4 Example The following example specifies to exit from the Exec mode or Privileged Exec mode switch_a gt logout switch_a login User s Manual 116 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Configuration Port Status Rate Control RMON Statistics Per Port Vlan Activities Configuration Admin Setting 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use the shutdown command to shut down the selected interface Use the no shutdown to disable this function 3 Command Syntax no shutdown 4 Example The following example shows the use of the shutdown command to shut down the interface fe1 port 1 switch_a config interface fe1 switch_a config if shutdown switch_a config if Bandwidth 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use this command to specify the bandwidth for each interface T
4. Switch version 1 43 1 01 22 09 15 40 59 switch_a gt enable swilch_allinstall image a 168 1 100 flash tgz Download now please wait tftp flash tgz from ip 192 168 1 100 success Install now This may take several minutes please wait Install success switch_att At the switch_a prompt just type in reload and press lt Enter gt to reboot the switch after completing the upgrade process 115200 HyperTerminal Elle dx Yew Call Transfer Help Oe 3 oo switch atreload Reboot now please wait The system is going down NOW Sending SIGTERM to all processes Connection is closed by administrator Sending SIGKILL to all processes Requesting system reboot Start bootloader Uncompressing image Starting image switch_a login User s Manual 115 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Reboot 1 Command Mode Privileged Exec mode Logon to Privileged Exec Mode Enable Mode The switch_a prompt will show on the screen switch_a 2 Usage Use reload command to restart switch 3 Command Syntax reload 4 Example The following example specifies restarting switch switch_a reload switch_a login Logout 1 Command Mode Exec mode or Privileged Exec mode Logon to Exec Mode View Mode or Privileged Exec Mode Enable Mode The switch_a gt or switch_a prompt will show on the screen switch_a gt
5. http 192 168 1 10 cgi bin switch cgi K Management Switch HO System Ageing Time seconds Setageingtime 300 BO Port Update Setting EE Switching Bridging Port Threshold level 0 1 100 Storm control enabled type Shee Level Broadcast DLF Multicast Port Mirroring PoE Level Broadcast DLF Multicast PoE Scheduling Level Broadcast DLF Multicast os Level Broadcast DLF Muticast TA Broadcast CIDLF Multi H VLAN Level roadcast Multicast HO Qos Level Broadcast DLF Multicast HA SNMP j Level Broadcast DLF Multicast HG 802 1x Level Broadcast C DLF Multicast E Other Protocols Update Setti pdate Setting Internet Bridging 1 Aging Time seconds Click the text box and type a decimal number as Bridging Aging Time in seconds 2 Update Setting Click Update Setting button when you finished Aging Time settings 3 Threshold level 0 1 100 Click in Level text box and type a decimal number for the port Need to choose Broadcast and or DFL Multicast from Storm control enabled type for the port DLF Destination Lookup Failure 4 Storm control enabled type Choose Broadcast and or DLF Multicast from Storm control enabled type for the port 5 Update Setting Click Update Setting button when you finished Threshold level and Storm control enabled type settings User s Manual 52 SIGNAMA
6. no Negate a command or set its defaults priority queue Enable the egress expedite queue service Set up miscellaneous service sel Set GHRP Registration to Fixed Registration show Show running system information snmp server Configure snmp setting username Establish User Name Authentication vlan Configure VLAN parameters wrr queue WRR queue switch_alconfig show cli Show CLI tree of current mode list _ Show command lists running config Current Operating configuration switch_a config show _ Connected 0 25 15 VT100 115200 6 11 Login timed out The login session to Configure Mode or Configure Terminal Mode has timed out due to an extended period of inactivity 60 seconds to indicate authentication attempt timed out And the switch_a login prompt will show on the screen Logon back to Exec Mode View Mode At the switch_a login prompt just type in root and press lt Enter gt to logon back to Exec Mode or View Mode switch_a login root User s Manual 106 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 115200 HyperTerminal File Edit View Call Transfer Help Oe s3 op e switch_a login root Switch version 1 30 r142 sdkr32 12 05 07 13 59 04 switch_a gt enable switch_a configure terminal Enter configuration commands one per line End with CNTL Z switch_a config Vty connection is timed out switch_a login Login timed out after 60 seconds swit
7. 3 Command Syntax snmp server trap ipaddress lt 1 5 gt IP ADDRESS no snmp server trap ipaddress lt 1 5 gt lt 1 5 gt The trap host IP address 1 5 IP ADDRESS The trap host IP address for SNMP A B C D specifies the IP address 4 Example The following example specifies trap host 1 IP address 192 168 1 20 for SNMP switch_a config snmp server trap ipaddress 1 192 168 1 20 switch_a config User s Manual 157 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Cold Start Trap 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use snmp server trap type enable coldStart command to enable cold start trap for SNMP Use the no snmp server trap type enable coldStart command to disable cold start trap for SNMP 3 Command Syntax no snmp server trap type enable coldStart 4 Example The following example enables cold start trap for SNMP switch_a config snmp server trap type enable coldStart switch_a config Warm Start Trap 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use snmp server trap type enable warmStart command to enable warm start trap for SNMP Use the no snmp server trap type enable warmStart comman
8. INSTANCE_ID Specify the instance ID BRIDGE_PRIORITY lt 0 61440 gt Specify the bridge priority 4 Example The following example sets the bridge priority 0 for an MST instance 3 in bridge GROUP 1 switch_a config bridge 1 instance 3 priority 0 switch_a config MSTP Port Setting Bridge Group Instance 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use this command to assign a Multiple Spanning Tree instance to a port Use the no parameter with this command to remove the instance 3 Command Syntax bridge GROUP instance INSTANCE_ID no bridge GROUP instance INSTANCE_ID GROUP lt 1 1 gt Specify the bridge group ID INSTANCE_ID Specify the instance ID 4 Example The following example assigns a Multiple Spanning Tree instance 3 to a port fe1 in bridge GROUP 1 User s Manual 142 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch switch_a config interface fe1 switch_a config if bridge group 1 instance 3 switch_a config if Bridge Group Instance Priority 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen
9. Port Switching Trunking STP Ring VLAN Qs B E SNMP SNMP General Setting SNMP vive SNMP v3 802 1 Other Protocols Delete User User Name Access Mode Security Level Authentication Type Privacy Type T Internet User s Manual 81 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch amp Welcome to Switch Management Microsoft Internet Explorer TAE File Edit View Favorites Tools Help a Q sac Q x a A JO Search she Favorites O 2j 3 Address http 192 168 1 10 cgi bin switch cgi v gt Go Links m1 2 3 4 s E D EALA E p Mae Gi Management Switch E OQ System SNMP V3 Setting Port SNMP Version SNMPv3 No Auth Switching User Name a Tronking Access Mode ReadOnly Reba Auth Password pE VLAN Passwor Qos Privacy PassPhrase gs NV i SNMP viiv2c SNMP v3 HH 802 1x E Other Protocols Done Internet SNMP v3 Add User 1 Add User Click Add User button The SNMP V3 Setting window appears 2 SNMP Version Click SNMP Version drop down menu from SNMP Version drop down list to choose SNMPv3 No Auth SNMPv3 Auth MD5 SNMPv3 Auth SHA SNMPv3 Priv Auth MD5 or SNMPv3 Priv Auth SHA e SNMPv3 No Auth Add a user using SNMP v3 without authentication e SNMPv3 Auth MD5 Add a user using SNMP v3 with authentication Click in the Auth Password textbox and sp
10. SNMP HA 802 1x Other Protocols ells lal lt TEO TE w r EAA a Done Internet 802 1p Priority 1 Priority Click Priority drop down menu from Priority drop down list to choose 0 3 for VLAN Priority 0 7 2 Submit Click Submit button when you finished 802 1p priority User s Manual 77 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer BEE C7 File Edit View Favorites Tools Help Q sack Q x a CA JO Search J Favorites O A7 amp E 3 Address http 192 168 1 10 cgi bin switch cgi Eco Links gt alel elle EJE o o e s s SIS ILS K3 802 1x C Other Protocols RIR lt 0 0 0 0 0 0 0 o oi 0 lt felfe cael C lt Internet DSCP 1 Priority Click Priority drop down menu from Priority drop down list to choose 0 3 for DSCP Priority 0 63 2 Submit Click Submit button when you finished DSCP User s Manual 78 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch File Edit View Favorites Tools Help Q sack X x a CAN Pa Search Sie Favorites Neha 2 E 3 Address http 192 168 1 10 cgi bin switch cgi Gi Management Switch HO System SNMP Status Disable v O Port SNMP General Setting HO Switching Description Trunking STP Ring HO VL
11. a Welcome to Switch Management Microsoft Internet Explorer Ce File Edit View Favorites Tools Help a Q sack amp x E EA p gt Search sie Favorites amp tS amp B 3 Address http 192 168 1 10 cgi bin switch cgi yl Eco links Management Switch gt System O Port Switching Trunking STP Ring BG VLAN VLAN Mode Setting 802 10 VLAN Setting 802 10 Port Setting Port Based VLAN Hybrid i gt os 7 Hybrid SNMP c 802 1x 4 Other Protocols Update Setting VLAN Port Setting Mode Hybrid 7 Hybrid Hybrid Hybrid OA nm Bl we w e 1 1 1 Hybrid 1 1 1 1 1 Hybrid Internet 802 1Q Port Setting 1 802 1Q Port Setting Click 802 1Q Port Setting The VLAN Port Setting window appears 2 Mode Click Mode drop down menu to Choose Access Trunk or Hybrid from Mode drop down list for the port The port will be Tag port if you choose Trunk Mode for the port And the port will be Tag or Untag port if you choose Hybrid Mode for the port 3 PVID Click in the PVID textbox and specify a new PVID number for the port 4 Update Setting Click Update Setting button when you finished VLAN Port Setting User s Manual 73 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Z Welcome to Switch Management Microsoft Internet Explorer DER File Edit View Favorites
12. 802 1Q Port Setting Port Based VLAN QOS Global Configuration 802 1p Priority DSCP SNMP SNMP General Setting SNMP v1 v2c SNMP v3 802 1X Radius Configuration Port Authentication OTHER PROTOCOLS GVRP IGMP Snooping NTP User s Manual 32 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer DAR A File Edit View Favorites Tools Help Q pack amp x E EA j Search sie Favorites O ha amp 3 Address http 192 168 1 10 cgi bin switch cgi v Go Links gt K Management Switch EQ System System information System Information System name switch_a System Name Password Firmware version 1 91 0 09 28 11 12 17 25 IP Address System time Thu Jan 01 18 29 22 UCT 2009 ARP Table MAC address 00e0 b321 2828 Route Table Default gateway None Save Configuration DNS Server None Reboot VLAN ID IP Address IP Subnet Mask Logout BO Port HO Switching HO Trnking STP Ring VLAN BA Qos BO SNMP BA 802 1x C Other Protocols 1 192 168 1 10 Done Internet System Information The System name Firmware version System time MAC address Default gateway DNS Server VLAN ID IP Address and IP Subnet Mask of Switch User s Manual 33 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch A Welcome to Switch Management Microsoft Internet Explorer Cel ay File Edit View Favorites Tools Help Q p
13. Australia Tasmania Australia Victoria LHT 10 30LHDT Australia Lord_Howe Australia LHI TST 10TDT Australia Hobart NZST 12NZDT Antarctica McMurdo Pacific Auckland Antarctica South_Pole NZ User s Manual 185 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch CIST 12 45CIDT Pacific Chatham NZ CHAT Africa SAST 2 EST 2EDT Africa Maseru Africa Johannesburg Africa Mbabane Africa Cairo Egypt UAEST 4 Asia Dubai IST 3IDT Asia Baghdad JST 2UDT Asia Amman SST 2SDT Asia Damascus Universal UCT Africa Ouagadougou Africa Abidjan Africa Banjul Africa Accra Africa Conakry Africa Bissau Africa Monrovia Africa Bamako Africa Nouakchott Africa Casablanca Africa El_Aaiun Atlantic St_Helena Africa Sao_Tome Africa Dakar Africa Freetown Africa Lome America Danmarkshavn Atlantic Reykjavik Etc GMT Etc UTC Etc UCT GMT Etc Universal Etc Zulu Etc Greenwich Etc GMT 0 Etc GMT 0 Etc GMTO Africa Timbuktu GMT 0 GMT 0 GMTO Greenwich Iceland UCT UTC Universal Zulu UCT1 Atlantic Cape_Verde Etc GMT 1 UCT2 Atlantic South_Georgia Etc GMT 2 UCT3 Antarctica Rothera America Belem America Cayenne America Paramaribo Etc GMT 3 UCT4 America Anguilla America Antigua America Barbados America Dominica America Grenada America Guadeloupe America Martinique Ame
14. CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 2 Usage Use this command to set the cost of a path associated with an interface Use the no parameter with this command to restore the default cost value of the path A lower path cost indicates a greater likelihood of the specific interface becoming a root 3 Command Syntax bridge GROUP instance INSTANCE_ID path cost PATH_COST GROUP lt 1 1 gt Specify the bridge group ID INSTANCE_ID lt 1 15 gt Specify the instance ID PATH_COST lt 1 200000000 gt Specify the cost of path in the range of lt 1 200000000 gt 4 Example The following example sets the path cost 1000 for Multiple Spanning Tree instance 3 to a port fe1 in bridge GROUP 1 switch_a config interface fe1 switch_a config if bridge group 1 instance 3 path cost 1000 switch_a config if Recover Ring tm Capability Ring state 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to enable Ring state Use the no parameter with this command to disable Ring state 3 Command Syntax bridge GROUP protocol ring no bridge GROUP ring enable BRIDGE FORWARD GROUP lt 1 1 gt Specify the bridge group ID BRIDGE FORWARD Puts all ports of the specified bridge into the forwarding state 4 Example The following example enables Ring state in bridge GR
15. and RMON MIB RMON activities are performed at a Network Management Station running an SNMP network management application with graphical user interface User s Manual 26 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch SNMP Agent and MIB 2 RFC 1213 The SNMP Agent running on the switch manager CPU is responsible for Retrieving MIB counters from various layers of software modules according to the SNMP GET GET NEXT frame messages Setting MIB variables according to the SNMP SET frame message Generating an SNMP TRAP frame message to the Network Management Station if the threshold of a certain MIB counter is reached or if other trap conditions such as the following are met WARM START COLD START LINK UP LINK DOWN AUTHENTICATION FAILURE RISING ALARM FALLING ALARM TOPOLOGY ALARM MIB II defines a set of manageable objects in various layers of the TCP IP protocol suites MIB II covers all manageable objects from layer 1 to layer 4 and as a result is the major SNMP MIB supported by all vendors in the networking industry The switch supports a complete implementation of SNMP Agent and MIB II RMON MIB RFC 2819 and Bridge MIB RFC TECK The switch provides hardware based RMON counters in the switch chipset The switch manager CPU polls these counters periodically to collect the statistics in a format that complies with the RMON MIB definition User s Manual 27 SIGNAM
16. root Switch version 1 38 r142 sdkr32 12 05 07 13 59 04 switch_a gt Vty connection is timed out switch_a login Login timed out after 68 seconds switch_a login Connected 0 18 59 T1003 115200 8 N 1 Exit from Exec Mode View Mode At the switch_a gt prompt just type in exit and press lt Enter gt to exit from Exec Mode or View Mode switch_a gt exit User s Manual 98 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 115200 HyperTerminal File Edit View Call Transfer Help D a 8060 g switch_a login root Switch version 1 30 r142 sdkr32 12 05 07 13 59 04 switch_a gt exit switch_a login Connected 0 19 58 T1003 115200 8 N 1 Privileged Exec Mode Enable Mode Logon to Privileged Exec Mode Enable Mode At the switch_a gt prompt just type in enable and press lt Enter gt to logon to Privileged Exec Mode or Enable Mode And the switch_a prompt will show on the screen switch_a gt enable User s Manual 99 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 115200 HyperTerminal File Edit View Call Transfer Help Oe s3 op Gg switch_a login root Switch version 1 98 r142 sdkr32 12 05 07 13 59 04 switch_a gt enable switch_alt Connected 0 01 20 VT100 115200 6 1 Commands Privileged Exec Mode or Enable Mode allows users to run commands as following At the switch_a prompt just press lt
17. switch_a config interface fe1 switch_a config if 2 Usage Use this command to set the port priority for a bridge group The Multiple Spanning Tree Protocol uses port priority as a tiebreaker to determine which port should forward frames for a particular instance on a LAN or which port should be the root port for an instance A lower value implies a better priority In the case of the same priority the interface index will serve as the tiebreaker with the lower numbered interface being preferred over others The permitted range is 0 240 The priority values can only be set in increments of 16 3 Command Syntax bridge GROUP instance INSTANCE_ID priority PRIORITY GROUP lt 1 1 gt Specify the bridge group ID INSTANCE_ID lt 1 15 gt Specify the instance ID PRIORITY lt 0 240 gt Specify the port priority in a range of lt 0 240 gt 4 Example The following example sets the port priority 121 for Multiple Spanning Tree instance 3 to a port fe1 in bridge GROUP 1 switch_a config interface fe1 switch_a config if bridge group 1 instance 3 priority 121 switch_a config if Bridge Group Instance Path Cost 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if User s Manual 143 SIGNAMAX
18. textbox and specify a new VLAN ID number from 2 4094 4 VLAN Name Click in the VLAN Name textbox and type a name for this newly created VLAN ied port to or delete port from VLAN VLAN Member Choose the port to be added to or deleted from the VLAN 2 Tag or Untag Click Tag or Untag drop down menu to Choose Tag or Untag from Tag or Untag drop down list for a Hybrid port 3 Submit Click Submit button when you finished VLAN setting 4 Welcome to Switch Management Microsoft Internet Explorer TEE File Edit View Favorites Tools iis Q sack Q x a F J Search sie Favorites 2 a 3 Addres s http 192 168 1 10 cgi bin switch cgi v Go Links Ge Management Switch HO System Select a VLAN ID PO Pot HO Switching HO Trunking STP Ring SQ VLAN VLAN Mode Setting 802 10 VLAN Setting 02 10 Port Setting Port Based VLAN HA Qos amp SNMP HO 8021x H Other Protocols Done Internet Delete VLAN 1 802 1Q VLAN Setting Click 802 1Q VLAN Setting The VLAN Setting window appears User s Manual 72 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 2 Delete VLAN Click Delete VLAN button 3 Select a VLAN ID Click Select a VLAN ID drop down menu from Select a VLAN ID drop down list to choose the VLAN to be deleted 4 Submit Click Submit button when you finished VLAN setting
19. 0 and 61440 3 Hello Time sec 1 9 Click in Hello Time text box and type a decimal number between 1 and 9 4 Max Age sec 6 28 Click in Max Age text box and type a decimal number between 6 and 28 5 Forward Delay sec 4 30 Click in Forward Delay text box and type a decimal number between 4 and 30 User s Manual 60 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 6 STP Version Click STP Version drop down menu to choose MSTP RSTP or STP compatible from STP Version drop down list 7 Update Setting Click Update Setting button when you finished Global Configuration 3 Welcome to Switch Management Microsoft Internet Explorer Ble gat yew Favorites Tools Help O AGH Psn Irre C Sas henp 192 168 2 20 egr tery switeh egi y Port Status Prioeity Path Cost Pois to Point Link Edge Port D Pat Ta BCO Sencha 1 Desagated F orwarding 128 6200000 point to point Disabled ELO Trunking 2 Disabled Discarding 128 200000 shared Disabled FA srzi Disabled Discarding 128 200000 shared Disabled Cistai Configatats BIIP Pont Setting 4 Disabled Discarding s 200000 shared Disabled ee DisabledDiscarding 128 200000 shared Disabled MSTP Instance Setting MIP a Seton 6 DisabledDiscerding s shared Disabled i Disabled Discardng shared Disabled EE VLAN ED Qs S Disabled Discarding 125 20000 shared D
20. 1 VLAN Mode Setting Click VLAN Mode Setting drop down menu to Choose Tag based VLAN or Port based VLAN from VLAN Mode Setting drop down list 2 Submit Click Submit button when you finished VLAN Mode Setting User s Manual 70 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer DAR i Eile Edit View Favorites Tools Help Q sack Q x E pe Search he Favorites amp amp 3 BESS G bitp 192 168 1 10 o9 bin satch ogi co tints a gt pt tT f S K Management Switch VLAN Mode 1 Tag Based VLAN VLAN Setting Add VLAN _ Delete VLAN VLAN ID VLAN NAME VLAN1 802 10 VLAN Setting Port Based VLAN Internet Bile dt Wew Fgvortes Tools Help Q DICES P searen Se Fones hetp 192 168 1 10 09 bin witch eg BEMA G Managemen Swich HO Sytem VLAN ID 2 4094 VLAN Name RO Pon A Saiti VLAN Setting EO Treking BLI STP Ring PORT SA VLAN Por Band VLAN HO Os HO SNMP HO Mi SC Other Protocols Subend User s Manual 71 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 802 1Q VLAN Setting Add VLAN 1 802 1Q VLAN Setting Click 802 1Q VLAN Setting The VLAN Setting window appears 2 Add VLAN Click Add VLAN button to create a new VLAN from VLAN Setting window 3 VLAN ID 2 4094 Click in the VLAN ID
21. 2 Submit Click Submit button when you finished Port Trunking settings User s Manual 59 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch STP Ring omk amp i Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help Q Back Q CA P Search sie Favorites O Address http 192 168 1 10 cgi bin switch cgi W Management Switch BO System HE Port Bridge ID 800000e0b3212829 HO Switching Designated Root 800000e0b3212829 Trunking Reg Root ID AE STP Ring Root Port Global Configuration Root Path Cost RSTP Port Setting Current Max Age sec MSTP Properties Current Hello Time sec MSTP Instance Setting Current Forward Delay sec MSTP Port Setting Hold Time sec Recover Ring tm Capability Topology Change Count BH VLAN HA Qos SNMP HO 802 1x EE Other Protocols Bridge Priority 0 61440 32768 Hello Time 1 10 sec 2 Max Age 6 40 sec 20 Forward Delay 4 30 sec 15 STP Version g Time Since Last Topology Change Setting Spanning Tree Protocol Enable Update Setting Internet Global Configuration 1 Spanning Tree Protocol Click Spanning Tree Protocol drop down menu to Choose Enable or Disable from Spanning Tree Protocol drop down list to enable or disable Spanning Tree Protocol 2 Bridge Priority 0 61440 Click in Bridge Priority text box and type a decimal number between
22. 6 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch a Login Microsoft Internet Explorer DER ay File Edit View Favorites Tools Help Q sack Q x a LA p gt Search Sig Favorites 2 B 3 Address http 192 168 1 10 v E co Links Internet Enter the factory default login ID root Enter the factory default password no password Then click on the Login button to log on to the switch User s Manual 7 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch a Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help Q pack Q x a J Search Sig Favorites far B 3 Address http 192 168 1 10 cgi bin switch cgi v Go Links W Management Switch FHC System System information System name switch_a Firmware version 1 91 0 09 28 11 12 17 25 System time Thu Jan 01 18 03 36 UCT 2009 MAC address 00e0 b321 2828 Default gateway None DNS Server None 802 1 VLAN ID IP Address E Other Protocols 1 192 168 1 10 Done Internet User s Manual 8 CONNECTIVITY SYSTEMS gt Hardened Managed PoE Ethernet Switch Preface This manual describes how to install and use the Signamax Hardened Managed PoE Power over Ethernet Ethernet Switch This switch introduced here is designed to deliver full scalability with SNMP RMON web based management functions by providing To get the most out of this
23. CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch switch_a config 2 Usage Use this command to set the hello time the time in seconds after which if this bridge is the root bridge all the bridges in a bridged LAN exchange Bridge Protocol Data Units BPDUs 3 Command Syntax bridge GROUP hello time HELLOTIME no bridge GROUP hello time GROUP lt 1 1 gt The ID of the bridge group to which this hello time is assigned HELLOTIME lt 1 9 gt The hello BPDU interval in seconds 4 Example The following example sets the hello time HELLOTIME 9 of bridge GROUP 1 switch_a config bridge 1 hello time 9 switch_a config Max Age sec 6 28 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to set the max age for a bridge Use the no parameter with this command to restore the default value of max age 3 Command Syntax bridge GROUP max age MAXAGE no bridge GROUP max age GROUP lt 1 1 gt The ID of the bridge group to which this maximum age time is assigned MAXAGE lt 6 28 gt The maximum time in seconds to listen for the root bridge 4 Example The following example sets the max age MAXAGE 28 of bridge GROUP 1 switch_a config bridge 1 max age 28 switch_a config User s Manual 135 SIGNAMAX CONNECTIVITY SYS
24. Cuba EST5EDT_CU America Havana Cuba North America Haiti EST5EDT_HT America Nassau America Santo_Domingo America Port au Prince America Bogota North America Mexico PST8PDT_MX America Tijuana America Ensenada Mexico BajaNorte MST7MDT_MX America Chihuahua America Hermosillo America Mazatlan Mexico BajaSur CST6CDT_MX America Guatemala North America Turks and Caicos EST5EDT_TC Additions Since 10g RTM America Grand_Turk EST5EDT_INDIANA America Indiana Indianapolis America Indiana Marengo America Indiana Vevay America Fort_Wayne America Indianapolis America Indiana Knox America Knox_IN US Indiana Starke US East Indiana UCT 8_WA Australia Perth Australia West User s Manual 189 CONNECTIVITY SYSTEMS gt Hardened Managed PoE Ethernet Switch Contact Information SIGNAMAX CONNECTIVITY SYSTEMS An AESP Company 16295 N W 13h Avenue Miami Florida 33169 U S A Phone 305 944 7710 Fax 305 949 4483 Sales 800 446 2377 Tech Support 800 446 2377 ext 201 Http www signamax com E mail info signamax com User s Manual 190
25. Designated Designated Designated SO STP Rag Pot Pot State Role Privy Com Bdge ID Post ID Root ID Path Cost 1 HO Qs HO SNMP PO M CD Other Protocol k MSTP Port Configuration Port Priority Gramndarity 16 Admin Path Cost i Update Seting O internet User s Manual 66 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer DEAR a File Edit View Favorites Tools Help Back QJ x ie EA D Search Favorites 4 B ER S wf a Address http 192 168 1 10 cgi bin switch cgi vE co Links K Management Switch O System O Port Port HO Switching Port AO Trunking Port Port EE STP Ring Instance ID Port Global Configuration Port RSTP Port Setting Port MSTP Properties Port 8 MSTP Port Setting Recover Ring tm Capability JEO VLAN Qs SNMP 82021x 4 Other Protocols ADM EWE Done Internet MSTP Port Setting Port Instance Configuration 1 Instance ID Click Instance ID drop down menu to choose instance ID from Instance ID drop down list 2 Click Port 1 Port 8 to assign ports to the corresponding instance ID 3 Update Setting Click Update Setting button when you finished Port Instance Configuration Instance ID 1 Instance ID Click Instance ID drop down menu t
26. Hardened Managed PoE Ethernet Switch 115200 HyperTerminal File Edit View Call Transfer Help Oe s3 oo GS ip Internet Protocol IP lacp LACP commands lacp counter LACP commands list Show command lists mac Mac address memory Memory information mirror Port Mirroring mls Switch L2 nsm NSM port port commands privilege Show current privilege level ratecontrol The layer2 interface running conf ig Current Operating configuration spanning tree Display spanning tree information star tup config Contents of startup configuration static channel group Static channel commands storm control The layer2 interface user priority Display the default user priority associated with the layer interface users Display information about terminal lines version Display version vlan Display VLAN information switch_atishow _ Connected 0 04 44 T1003 115200 amp N 1 Login timed out The login session to Privileged Exec Mode or Enable Mode has timed out due to an extended period of inactivity 60 seconds to indicate authentication attempt timed out And the switch_a login prompt will show on the screen Logon back to Exec Mode View Mode At the switch_a login prompt just type in root and press lt Enter gt to logon back to Exec Mode or View Mode switch_a login root User s Manual 102 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 115200 HyperTerminal File Edit View C
27. Management The switch provides a web based browser interface for configuring and managing the switch This interface allows you to access the switch using a preferred web browser This chapter describes how to configure the switch using its web based browser interface User s Manual 25 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch SNMP amp RMON Management This chapter describes the switchs Simple Network Management Protocol SNMP and Remote Monitoring RMON capabilities Overview RMON is an abbreviation for the Remote Monitoring MIB Management Information Base RMON is a system defined by the Internet Engineering Task Force IETF document RFC 2819 which defines how networks can be monitored remotely RMONs typically consist of two components an RMON probe and a management workstation The RMON probe is an intelligent device or software agent that continually collects statistics about a LAN segment or VLAN The RMON probe transfers the collected data to a management workstation on request or when a pre defined threshold is reached The management workstation collects the statistics that the RMON probe gathers The workstation can reside on the same network as the probe or it can have an in band or out of band connection to the probe The switch provides RMON capabilities that allow network administrators to set parameters and view statistical counters defined in MIB II Bridge MIB
28. Ni Management Switch EG System System Information tem Nz w IP Address ARP Table Route Table Download now please wait thp flash tgz from ip 192 168 1 100 success Install now This may take several minutes please wait ve Ci 802 1x Other Protocols Internet Firmware has been upgraded successfully to the switch Reboot the switch after completing the upgrade process User s Manual 42 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch File Edit View Favorites Tools Help a Welcome to Switch Management Microsoft Internet Explorer TER Ay Q pack Q x a EA JO Search She Favorites Ez B7 gt 3 Address http 192 168 1 10 cgi bin switch cgi s Eco links 802 1x Other Protocols Internet User s Manual 43 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch a Welcome to Switch Management Microsoft Internet Explorer Eek File Edit View Favorites Tools Help a Q ack Q x E Search Sie Favorites B 2 3 Address http 192 168 1 10 cgi bin switch cgi vl Eco Links K Management Switch AA 802 1x E Other Protocols Internet Reboot Reboot Click Reboot button to restart the switch User s Manual 44 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer DER ay File Edit View F
29. Reboot Logout BED Port Disable BO Switching HO Trunking HA STP Ring MAC Address 00e0 b321 2828 VLAN FED Qos HE SNMP H 802 1x C Other Protocols Done Internet IP Address 1 IP Address Click in IP Address text box and type a new address to change the IP Address 2 IP Subnet Mask Click in IP Subnet Mask text box and type a new address to change the IP Subnet Mask 3 Submit Click Submit button when you finished these selections 4 You need to enter the new IP address on the browser and reconnect to the switch after IP or subnet mask are changed 5 Default Gateway Click Default Gateway drop down menu to choose Disable or Enable from the Default Gateway drop down list to disable or enable Default Gateway Setting for the switch Click the text box and type a new address to change the Default Gateway Need to choose Enable from the Default Gateway drop down menu 6 Submit Click Submit button when you finished Default Gateway 7 DNS Server Click DNS Server drop down menu to choose Disable or Enable from the DNS Server drop down list to disable or enable DNS Server Setting for the switch Click the text box and type a new address to change the DNS Server Need to choose Enable from the DNS Server drop down menu User s Manual 35 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet
30. Switch 8 Submit Click Submit button when you finished DNS Server Z Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help i Q Back Q x 2 EA p gt Search sie Favorites fr s 3 Address http 192 168 1 10 cgi bin switch cgi v Go Links S Ed p E e Ca Management Switch EQ System ARP Table IP Address eas Flags Hardware Address Mask VLAN 192 168 1 100 1 2 00 10 DCFC 31 02 1 BO Port BO Switching Trunking STP Ring BO VLAN BA QoS f SNMP 802 15 E O Other Protocols Done Internet ARP Table Click ARP Table to view ARP Table User s Manual 36 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch a Welcome to Switch Management Microsoft Internet Explorer Cel ay File Edit View Favorites Tools Help Q pack Q x a EA gt Search Sig Favorites far B 3 Address http 192 168 1 10 cgi bin switch cgi v Go links W Management Switch BE System 5 Destination Gateway Genmask Flags Metric Ref Use VLAN 192 168 1 0 0 0 0 0 255 255 0 0 0 1 5 127 0 0 0 0 0 0 0 255 0 0 J 0 00 1 HO Port Switching Trunking HG STP Ring j gt VLAN E0 Qos SNMP HA 802 1x Other Protocols Done Internet Route Table Click Route Table to view Route Table User s Manual 37 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet S
31. Usage Use storm control broadcast enable command to enable broadcast traffic Use no storm control broadcast command to disable broadcast traffic 3 Command Syntax storm control broadcast enable no storm control broadcast 4 Example The following example shows setting storm control broadcast enable to the interface fe1 port 1 switch_a config interface fe1 switch_a config if storm control broadcast enable switch_a config if Multicast 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage User s Manual 123 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Use storm control multicast enable command to enable multicast traffic Use no storm control multicast command to disable multicast traffic 3 Command Syntax storm control multicast enable no storm control multicast 4 Example The following example shows setting storm control multicast enable to the interface fe1 port 1 switch_a config interface fe1 switch_a config if storm control multicast enable switch_a config if DLF 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt w
32. View Call Transfer Help Oe s3 oOo g switch_a login _ Connected 0 02 04 T1003 115200 8 N 1 Logon to Exec Mode View Mode At the switch_a login prompt just type in root and press lt Enter gt to logon to Exec Mode or View Mode switch_a login root 115200 HyperTerminal File Edit View Call Transfer Help Oe s3 e switch_a login root Switch version 1 30 r142 sdkr32 12 05 07 13 59 04 switch_a gt _ Connected 0 02 55 VT1003 115200 amp N 1 User s Manual 95 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Basic commands Exec Mode or View Mode is the base mode from where users can perform basic commands like clear debug disable enable exit help logout no quit show terminal The CLI contains a text based help facility Access this help by typing in the full or partial command string then typing a question mark The CLI displays the command keywords or parameters along with a short description At the switch_a gt prompt just press lt gt to list the above basic commands switch_a gt 115200 HyperTerminal File Edit View Call Transfer Help Oe s3 Of g switch_a login root Switch version 1 30 r142 sdkr32 12 05 07 13 59 04 switch a gt Exec commands clear Clear the Forwarding database debug Debugging functions see also undebug disable Turn off privileged mode command enable Iurn on privileged mode command exit End curren
33. and its direction Use the no parameter with this command to disable port mirroring by the destination port on the specified source port 3 Command Syntax mirror interface SOURCEPORT direction SNOOPDIRECTION no mirror interface SOURCEPORT SOURCEPORT Name of the Source interface to be used SNOOPDIRECTION both receive transmit both Specifies mirroring of traffic in both directions receive Specifies mirroring of received traffic transmit Specifies mirroring of transmitted traffic 4 Example The following example enables port mirroring by the destination port fe1 port 1 on the specified source port fe2 port 2 switch_a config interface fe1 switch_a config if mirror interface fe2 direction both switch_a config if PoE System Power Budget 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to specify the power budget Watts to be set to Switch 3 Command Syntax User s Manual 126 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch poe system power budget LEVEL LEVEL lt 1 800 gt specifies the power budget Watts to be set to Switch 4 Example The following example sets new power budget 246 Watts to Switch switch_a config poe system power budget 246 switch_a config Enable Mode 1 Command Mode Interface mode Logon
34. assigned to the group 4 Example The following example sets the priority PRIORITY 100 of the interface fe1 User s Manual 136 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch port 1 of bridge GROUP 1 switch_a config interface fe1 switch_a config if bridge 1 priority 100 switch_a config if Admin Path Cost 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use this command to set the cost of a path associated with a bridge group Use the no parameter with this command to restore the default cost of a path associated with a bridge group 3 Command Syntax bridge GROUP path cost PATHCOST no bridge GROUP path cost GROUP lt 1 1 gt the ID of the bridge group PATHCOST lt 1 200000000 gt The cost to be assigned to the group 4 Example The following example sets the cost 123 of the interface fe1 port 1 of bridge GROUP 1 switch_a config interface fe1 switch_a config if bridge 1 path cost 123 switch_a config if Point to Point Link 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config
35. button The VLAN Instance Configuration window appears 2 VLAN ID Click VLAN ID drop down menu to choose VLAN from VLAN ID drop down list to simultaneously add multiple VLANs for the corresponding instance of a bridge 3 Instance ID 1 15 Click in Instance ID text box to specify the instance ID 4 Update Setting Click Update Setting button when you finished VLAN Instance Configuration Included VLANs 1 Instance ID Click Instance ID drop down menu to choose instance ID from Instance ID drop down list 2 Included VLAN Click Included VLAN drop down menu to choose VLAN from Included VLAN drop down list Instance Setting 1 Bridge Priority 0 61440 Click in Bridge Priority text box to set the bridge priority for an MST instance to the value specified The lower the priority of the bridge the better the chances are the bridge becoming a User s Manual 65 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch root bridge or a designated bridge for the LAN 2 Update Setting Click Update Setting button when you finished VLAN Instance Configuration J Welcome to Switch Management Microsoft Internet Explorer Ble gdt View Favortes Toots Help Ow O NAOH Pawn feros O G LBs A http 192 168 1 10 cg biny awiteh cgi Loo Ge Pod instance Configuration gt Suttchng Instance ID Trunking sey Path Designated
36. button when you finished MSTP Properties setting User s Manual 63 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer DER File Edit View Favorites Tools Help LJ i Q sack Q x E EA P Search She Favorites O E B 3 http 192 168 1 10 cgi bin switch cgi F co j Links Gi Management Switch System VLAN Instance Configuration Port Switching eC Trunk Instance ID EQ STP Ring Included VLAN Global Configuration RSTP Port Setting Bridge Priority 0 61440 MSTP Properties MSTP Instance Setting ort Setting Recover Ri Capabilit HO VLAN Bridge ID ba os SNMP 802 1 E Other Protocols Root ID Root Port Root Path Cost Internet User s Manual 64 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help a Q Back amp x a EA 9 Search sie Favorites O Q amp 3 Address http 192 168 1 10 cgi bin switch cgi Eco iins VLAN Instance Configuration VLAN ID Instance ID 1 15 Update Setting MSTP MSTP Instance Setting MSTP Port Setting Recover Ci HO VLAN E O Other Protocols Done z Internet MSTP Instance Setting VLAN Instance Configuration 1 VLAN Instance Configuration Click VLAN Instance Configuration
37. default frequency use the no ip igmp query interval command 3 Command Syntax ip igmp query interval INTERVAL no ip igmp query interval INTERVAL lt 1 18000 gt Frequency in seconds at which IGMP host query messages are sent Default 125 seconds 4 Example The following example changes the frequency of sending IGMP host query messages to 2 minutes on vlan1 1 switch_a config interface vian1 1 switch_a config if ip igmp query interval 120 switch_a config if IGMP querier Max response time 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode vian1 1 means vlan 1 The switch_a config if prompt will show on the screen switch_a config interface vian1 1 switch_a config if 2 Usage Use ip igmp query max response time command to configure the maximum response time advertised in IGMP queries User s Manual 174 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch To restore to the default value use the no ip igmp query max response time command 3 Command Syntax ip igmp query max response time RESPONSETIME no ip igmp query max response time RESPONSETIME lt 1 240 gt Maximum response time in seconds advertised in IGMP queries Default 10 seconds 4 Example The following example configures a maximum response time of 8 seconds on vian1 1 switch_a config interface vian1 1 switch_a co
38. deleted 3 Submit Click Submit button when you finished radius server deletion User s Manual 86 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 3 Welcome to Switch Management Microsoft Internet Explorer Pio Edit Yiew Favorites Jools Help QO x 2 Ch Oson ple rovortes http 192 168 1 10 cgi bin switch cgi 802 Lx Port Setting Interface Authentication State Port Control Periode Reauthentication Reauthentication Period lt 1 4294967295 gt Update Soning Port Port Enabled Port Control Ponsa Pe ee 1 Port Authentication 1 Interface Click Interface drop down menu from Interface drop down list to choose the port to be set port authentication 2 Authentication State Click Authentication State drop down menu from Authentication State drop down list to choose Enable or Disable to enable or disable authentication state 3 Port Control Click Port Control drop down menu from Port Control drop down list to choose Auto Force Authorized or Force Unauthorized to force a port state Auto specifies to enable authentication on port Force Authorized specifies to force a port to always be in an authorized state Force Unauthorized specifies to force a port to always be in an unauthorized state 4 Periodic Reauthentication Click Periodic Reauthentication drop down menu from Periodic Reaut
39. drop down list to choose Enable or Disable to enable or disable GVRP GARP VLAN Registration Protocol User s Manual 88 SIGNAMAX 2 CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Dynamic VLAN creation Click Dynamic VLAN creation drop down menu from Dynamic VLAN creation drop down list to choose Enable or Disable to enable or disable Dynamic VLAN creation GARP Generic Attribute Registration Protocol provides IEEE802 1Q compliant VLAN pruning and dynamic VLAN creation on IEEE802 1Q trunk ports Update Setting Click Update Setting button when you finished GVRP Global Setting port setting include LAG GVRP Click GVRP drop down menu from GVRP drop down list to choose Enable or Disable to enable or disable GVRP for the port GVRP applicant Click GVRP applicant drop down menu from GVRP applicant drop down list to choose Active or Normal to the port Ports in the GVRP active applicant state send GVRP VLAN declarations when they are in the STP Spanning Tree Protocol blocking state which prevents the STP bridge protocol data units BPDUs from being pruned from the other port Ports in the GVRP normal applicant state do not declare GVRP VLANs when in the STP blocking state GVRP registration Click GVRP registration drop down menu from GVRP registration drop down list to choose Enable or Disable to
40. is from 5 to 65535 And the default value is 30 seconds User s Manual 113 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 3 Command Syntax service auto config interval WORD WORD specifies the interval value 4 Example The following example sets the interval WORD 10 when the configuration would be automatically saved to switch switch_a config service auto config interval 10 switch_a config Firmware Upgrade 1 Command Mode Privileged Exec mode Logon to Privileged Exec Mode Enable Mode The switch_a prompt will show on the screen switch_a 2 Usage Use install image command to upgrade firmware from tftp server to switch 3 Command Syntax install image IP ADDRESS WORD IP ADDRESS specifies the IP address of tftp server WORD specifies the file name to be upgraded to switch 4 Example The following example specifies upgrading firmware file name flash tgz from tftp server IP address 192 168 1 100 to switch switch_a install image 192 168 1 100 flash tgz switch_a Please follow the message on the screen during the firmware upgrade process Do not turn off the power or perform other functions during this period of time User s Manual 114 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 115200 HyperTerminal Elle Edt yew Call Transfer Heb Oe s3 Of e Vty connection is timed out switch_a login root
41. one per line End with CNTL Z switch_a config Connected 0 22 54 T1009 115200 8 N 1 Commands Configure Mode or Configure Terminal Mode serves as a gateway into the modes as following At the switch_a config prompt just press lt gt to list the commands switch_a config User s Manual 104 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 115200 HyperTerminal File Edit View Call Transfer Help s3 ope Enter configuration commands one per line End with CNIL Z switch_alconfig I Configure commands banner Define a login banner bridge Bridge group commands debug Debugging functions see also undebug do To run exec commands in config mode enable Modify enable password parameters exit Fnd current mode and down to previous mode help Description of the interactive help system hostname Set system s network name interface Select an_interface_to configure ip Internet Protocol IP lacp LACP commands line Configure a terminal line log Logging control mls Switch L2 no Negate a command or set its defaults priority queue Enable the egress expedite queue service Set up miscellaneous service set Set GHRP Registration to Fixed Registration show Show running system information mm server Configure snmp setting ore Connected 0 23 38 VT100 115200 1 115200 HyperTerminal File Edit View Call Transfer Help s3 apg bridge Bridge group commands debug Debugging functio
42. s Manual 61 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Disable or Auto Edge Port for the port 7 Update Setting Click Update Setting button when you finished RSTP Port Setting 4 Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help Q sack Q x a EA JO Search she Favorites O A7 2 E 3 Add http 192 168 1 10 cgi bin switch cgi vl Eco Links K Management Switch EO System Port Bridge ID 800000e0b3212829 Switching Designated Root 800000e0b3212829 Trunking Reg Root ID 800000e0b3212829 F O STP Ring Root Port 0 Global Configuration Root Path Cost MSTP Properties Current Hello Time sec MSTP Instance Setting Current Forward Delay sec MSTP Port Setting Hold Time sec Recover Rine tm Capability O VLAN 0 RSTP Port Setting Current Max Age sec 20 2 1 Topology Change Count Time Since Last Topology Change EQ Qos F i Setting Pecan Spanning Tree Protocol Enable HO 802 1x Le EE Other Protocols Bridge Priority 0 61440 Hello Time 1 10 sec Max Age 6 40 sec Forward Delay 4 30 sec STP Version Update Setting Internet User s Manual 62 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help sack x A CD P search she Favorites O R 2b 3 ddress h
43. 0 17 00 1800 1900 20 00 21 00 22 00 2300 EANET EE E E E Dotote An J Dele As J Ocio An J Dolo All J Delete Al J Doia An Doioto an Submit HE Other Protocets internet PoE Scheduling First click on Switching from main menu Then click on PoE from Switching In PoE Port Setting click Enable Mode drop down menu to choose Scheduling from Enable Mode drop down list to schedule this port to discover Powered Device PD connected to this port PoE Per Port Scheduling 1 Port Click Port drop down menu to choose a port from Port drop down list and configure PoE scheduling to this port 2 Submit Click Submit button when you finished PoE Scheduling for this port User s Manual 58 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Z Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help Q tac i x a A Ks Search she Favorites 0 Q 3 http 192 168 1 10 cqi bin switch cgi K Management Switch BO System O Static Trak 3 Disable Note 4 ports maximum per trunk Internet Port Trunking Static Channel Group 1 Trunk 1 Click Port 1 Port 6 to assign ports to Trunk 1 Maximum 4 ports per Trunk GE Trunking 1 Trunk 3 Check Static or Disable to enable or disable Trunk 3 for Gigabit Ethernet ports
44. 12 gt Specifies from 1 to 12 DAY lt 1 31 gt Specifies from 1 to 31 HOUR lt 0 23 gt Specifies from 0 to 23 MINUTE lt 0 59 gt Specifies from 0 to 59 SECOND lt 0 59 gt Specifies from 0 to 59 4 Example The following example sets the time of RTC as July 20 2015 12 30 50 switch_a set clock 2015 7 20 12 30 50 switch_a NTP Status 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use ntp enable command to enable NTP for the Switch Use no ntp enable command to disable NTP for the Switch 3 Command Syntax no ntp enable 4 Example The following example enables NTP for the Switch switch_a config ntp enable switch_a config User s Manual 177 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch NTP Server 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to specify the IP address or Domain name of NTP server 3 Command Syntax ntp server IP ADDRESS DOMAIN NAME IP ADDRESS A B C D specifies the IP address of NTP server DOMAIN NAME Specifies the Domain name of NTP server 4 Example The following example specifies the IP address 192 168 1 100 of NTP server switch_a config ntp serve
45. 68 1 100 to switch switch_a config ip dns 192 168 1 100 switch_a config ARP Table 1 Command Mode Privileged Exec mode Logon to Privileged Exec Mode Enable Mode The switch_a prompt will show on the screen switch_a config 2 Usage Use show arp table command to view ARP Table 3 Command Syntax show arp table 4 Example User s Manual 110 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch The following example shows the ARP Table of switch switch_a show arp table Route Table 1 Command Mode Privileged Exec mode Logon to Privileged Exec Mode Enable Mode The switch_a prompt will show on the screen switch_a config 2 Usage Use show route table command to view Route Table 3 Command Syntax show route table 4 Example The following example shows the Route Table of switch switch_a show route table Save Configuration Load config from TFTP server 1 Command Mode Privileged Exec mode Logon to Privileged Exec Mode Enable Mode The switch_a prompt will show on the screen switch_a 2 Usage Use install image command to load configuration file from tftp server to switch 3 Command Syntax install image IP ADDRESS WORD IP ADDRESS specifies the IP address of tftp server WORD specifies the file name to be loaded to switch 4 Example The following example specifies upgrading firmware fi
46. 802 1p Priority DSCP 2 HO SNMP BC 802 1x 2 HO Other Protocols 3 8 Internet Global Configuration 1 QoS Click QoS drop down menu from QoS drop down list to choose Enable or Disable to enable or disable QoS 2 Trust Enable or disable the switch port to trust the CoS Class of Service labels of all traffic received on that port Enable or disable a routed port to trust the DSCP Differentiated Service Code Point labels of all traffic received on that port 3 Policy Choose Strict Priority Queue3 WRR Queue0 2 or WRR Queue0 3 A strict priority queue is always emptied first The queues that are used in the WRR Weighted Round Robin are emptied in a roundrobin fashion and you can configure the weight for each queue 4 Weighted Round Robin Click in the Weight 1 55 textbox and specify a new number from 1 55 for Queue 0 3 5 Submit Click Submit button when you finished Global Configuration User s Manual 76 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 4 Welcome to Switch Management Microsoft Internet Explorer SEE ay File Edit View Favorites Tools Help Back x Z E PO search Favorites 4 62 gt amp 3 gt w B sS Address http 192 168 1 10 cgi bin switch cgi E co Links K Management Switch System HO Port Switching O Trunking H STP Ring H VLAN AH Qos Global Configuration DSCP
47. AN Contact Qos rap Community Name 1 hg SNMP SNMP General Setting SNMP vive SNMP v3 rap Community Name 4 Location rap Community Name 2 rap Community Name 3 HO 8021x Trap Community Name 5 EC Othar Protocole rap Host 1 IP Address rap Host 2 IP Address rap Host 3 IP Address rap Host 4 IP Address Trap Host 5 IP Address Link Down Trap Disable v Link Up Trap Disable Update Setting Internet SNMP General Setting 1 SNMP Status Click SNMP Status drop down menu from SNMP Status drop down list to choose Enable or Disable to enable or disable SNMP 2 Description Click in the Description textbox and specify a new description for SNMP 3 Location Click in the Location textbox and specify a new location for SNMP 4 Contact Click in the Contact textbox and specify a new contact for User s Manual 79 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch SNMP 5 Trap Community Name For each Trap Community Name Click in the Trap Community Name textbox and specify a trap community name 6 Trap Host IP Address For each Trap Host IP Address Click in the Trap Host IP Address textbox and specify a trap host IP address 7 Link Down Trap Click Link Down Trap drop down menu from Link Down Trap drop down list to choose Enable or Disable to enable or disable link down trap 8 Link Up Tra
48. AX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch RMON Groups Supported The switch supports the following RMON MIB groups defined in RFC 2819 RMON Statistics Group maintains utilization and error statistics for the switch port being monitored RMON History Group gathers and stores periodic statistical samples from the previous Statistics Group RMON Alarm Group allows a network administrator to define alarm thresholds for any MIB variable An alarm can be associated with Low Threshold High Threshold or both A trigger can trigger an alarm when the value of a specific MIB variable exceeds a threshold falls below a threshold or exceeds or falls below a threshold RMON Event Group allows a network administrator to define actions based on alarms SNMP Traps are generated when RMON Alarms are triggered The action taken in the Network Management Station depends on the specific network management application Bridge Groups Supported The switch supports the following four groups of Bridge MIB RFC 1493 The dotidBase Group a mandatory group that contains the objects applicable to all types of bridges The dot1dStp Group contains objects that denote the bridge s state with respect to the Spanning Tree Protocol If a node does not implement the Spanning Tree Protocol this group will not be implemented This group is applicable to any transparent only source route or SRT bridge that im
49. Alarm 30 8 16 dbm NO TX Power Low Alarm 30 8 16 dbm NO TX Power High Warming 30 3 16 dbm N TX Power Low Warning 30 8 16 dbm NO Current Rx_pow 0 000 dbm RX Power High Alarm 30 8 16 dbm NO RX Power Low Alarm 30 8 16 dbm 0 000 NO RX Power High Warming 30 3 16 dbm 0 000 NO RX Power Low Warming 30 5 16 dbm 16980 NO Update Sening internet Port Status View the Link Status Speed Duplex and Flow control status for all ports SFP Port 1 View the Detected Connector Transceiver Mode Wave Length nm Link Length m Temperature C Vcc V Tx_bias mA Tx_pow dbm and Rx_pow dbm information for SFP ports 2 Alarm Situation View Current Temperature Alarm Current VCC Alarm Current Tx Bias Alarm Current Tx Power Alarm and Current Rx Power Alarm 3 Alarm Setting Click in Threshold Value text boxes and type new Threshold Values for Temp High Alarm Temp Low Alarm Temp High User s Manual 48 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Warning Temp Low Warning VCC High Alarm VCC Low Alarm VCC High Warning VCC Low Warning TX Bias High Alarm TX Bias Low Alarm TX Bias High Warning TX Bias Low Warning TX Power High Alarm TX Power Low Alarm TX Power High Warning TX Power Low Warning RX Power High Alarm RX Power Low Alarm RX Power High Warning RX Power Low Warning 4 Welcome to Switch Management Microsoft Internet Explorer DAR ay File Edit Vi
50. Classification Limit W PD Current Consumption Class mA W Power Status 1 Enable a High Searching N A 0 0 FC Other Protocol SoS 2 Enable High Searching N A 0 0 3 Enable High Searching N A 0 4 Enabe High Searching N A 0 Internet PoE System Setting 1 System Power Budget Click in System Power Budget text box and type a new system power budget for Switch 2 Submit Click Submit button when you finished PoE System Setting PoE Port Setting 1 Enable Mode Click Enable Mode drop down menu to choose Disable Enable or Scheduling from Enable Mode drop down list to disable enable or schedule this port to discover Powered Device PD connected to this port 2 Power Limit by Classification Check or uncheck Power Limit by Classification to enable or disable this port to provide power to PD according to classification of maximum power range used by PD 3 Fixed Power Limit W First uncheck Power Limit by Classification to disable this port to provide power to PD according to classification of maximum power range used by PD Then click in Fixed Power Limit W text box and type a new fixed power limit for this port to provide power to PD 4 Power Priority Click Power Priority drop down menu to choose High Medium or Low from the Power Priority drop down list to determi
51. Configure Mode Configure Terminal Mode Logon to VLAN Configure Mode The switch_a config vlan prompt will show on the screen switch_a config vlan database switch_a config vlan 2 Usage This command enables or disables the state of a particular VLAN on a bridge basis Specifying the disable state causes all forwarding over the specified VLAN ID on the specified bridge to cease Specifying the enable state allows forwarding of frames on the specified VLAN aware bridge 3 Command Syntax vlan VLANID bridge GROUP name VLAN_NAME state enable disable no vlan VLANID bridge GROUP VLANID The VID of the VLAN that will be enabled or disabled on the bridge lt 2 4094 gt User s Manual 146 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch GROUP lt 1 1 gt The ID of the bridge group on which the VLAN will be affected VLAN_NAME The ASCII name of the VLAN Maximum length 16 characters enable Sets VLAN into an enable state disable Sets VLAN into a disable state 4 Example The following example enables the vlan VLANID 2 and name VLAN_NAME vlan2 of bridge GROUP 1 switch_a config vlan vlan 2 bridge 1 name vian2 state enable switch_a config vlan 802 1Q Port Setting Switchport mode access 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will sho
52. Disable for the switch Use this command to enable report suppression for IGMP version 1 and version 2 Report suppression does not apply to IGMP version 3 and is turned off by default for IGMP version 1 and IGMP version 2 reports The switch uses IGMP report suppression to forward only one IGMP report per multicast router query to multicast devices When IGMP router suppression is enabled the switch sends the first IGMP report from all hosts for a group to all the multicast routers The switch does not send the remaining IGMP reports for the group to the multicast routers This feature prevents duplicate reports from being sent to the multicast devices Update Setting Click Update Setting button when you finished IGMP Snooping User s Manual 91 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 3 Welcome to Switch Management Microsoft Internet Explorer Ble Edit View Fortes Tools Help ma x 2 Eh P sern shy ravens http 192 168 1 10 0gi bin switch ogi A u EEEO GE Adjust RTC Time Year 2000 2037 2009 Month 1 Day 2 Fri Hour 0 Mime 35 Second 22 Update Semng NTP Setting VLAN bias NTP Status Osseble DO Qos HO sar NTP Server 19243244 18 HO 02 18 IP Address or Domain name Sme Tima SE Other Protocols Tane Zone GMT 12 00 Enwetok Kwapalein Current time Fri Jan 02 0033 25 UCT 2009 oee Euas Poling Interval 1 10080 min 60 xiz Update Seting Davtight Savin
53. IVITY SYSTEMS Hardened Managed PoE Ethernet Switch switch_a config if 2 Usage Use this command to set the interval between reauthorization attempts Use no dot1x timeout re authperiod command to delete the interval between reauthorization attempts 3 Command Syntax dot1x timeout re authperiod SECS no dot1x timeout re authperiod SECS lt 1 4294967295 gt Specify the seconds between reauthorization attempts The default time is 3600 seconds 4 Example The following example specifies to set the interval 25 seconds between reauthorization attempts switch_a config interface fe1 switch_a config if dot1x timeout re authperiod 25 switch_a config if User s Manual 168 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Other Protocols GVRP IGMP Snooping NTP GVRP GVRP 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use set gvrp enable bridge command to enable set and set gvrp disable bridge command to disable reset GVRP globally for the bridge instance This command does not enable disable GVRP in all ports of the bridge After enabling GVRP globally use the set port gvrp enable command to enable GVRP on individual ports of the bridge 3 Command Syntax set gvrp enable bridge GROUP set gvrp disable bridge GROUP GROUP Bridge gro
54. JEA K Management Switch HO System Select UserName Y EO Pe Switching O Trunking HE STP Ring VLAN Qos SNMP NM SNMP viiv2e SNMP v3 HH 8021x Other Protocols Done 7 Internet Delete User 1 Delete User Click Delete User button The Select User Name window appears 2 Select User Name Click Select User Name drop down menu from Select User Name drop down list to choose the user to be deleted from using SNMP v3 3 Submit Click Submit button when you finished user deletion User s Manual 83 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help Q Back Q x a EA p Search sie Favorites O 27 2 3 ess http 192 168 1 10 cgi bin switch cgi ee Go ie ee E K Management Switch HO System Radius Server Global Setting BO Port Radius Status Disable BO Trunking HO STP Ring E e R A FC Qos gt SNMP B 802 15 Radius Configuration Port Authentication H Other Protocols Order Radius Server IP Port Timeout Retransmit Done Internet Radius Configuration Key 1 Radius Status Click Radius Status drop down menu from Radius Status drop down list to choose Enable or Disable to globally enable or disable authentication 2 Update Setting Click Update Setting button when you fin
55. MAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch America Argentina Cordoba America Argentina Tucuman America Argentina La_Rioja America Argentina San_Juan America Argentina Jujuy America Argentina Catamarca America Argentina Mendoza America Argentina Rio_ Gallegos America Argentina Ushuaia America Argentina ComodRivadavia America Buenos_ Aires America Cordoba America Jujuy America Mendoza EBST3EBDT America Fortaleza America Recife America Araguaina America Maceio America Bahia America Sao_Paulo America Cuiaba America Montevideo America Catamarca America Rosario Brazil East WBST4WBDT America Campo_Grande America Boa_Vista America Manaus Atlantic Stanley America Asuncion Brazil West ACRE5 America Rio_Branco America Porto_Acre Brazil Acre NORO2 America Noronha Brazil DeNoronha CST4CDT Antarctica Palmer America Santiago Chile Continental EIST6EIDT Pacific Easter Chile Easterlsland Asia MST 8 Asia Kuala_Lumpur Asia Kuching CST 8 Asia Harbin Asia Shanghai Asia Chongaing Asia Urumdi Asia Kashgar Asia Hong_Kong Asia Macau Asia Macao Hongkong PRC ROC Oceania CST 9 30CDT Australia Adelaide Australia Broken_Hill Australia South Australia Yancowinna EST 10EDT Australia Brisbane Australia Lindeman Australia Currie Australia Melbourne Australia Sydney Australia ACT Australia Canberra Australia NSW Australia Queensland
56. Manual 39 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch a Welcome to Switch Management Microsoft Internet Explorer Ce ay File Edit View Favorites Tools Help Q Back Q x a H K Search She Favorites ahd 3 Address http 192 168 1 10 cgi bin switch cgi v B co Links Gv Firmware Version 1 91 0 09 28 11 12 17 25 Filename flash tgz System Name Password System Name Password TFTP server IP 192 168 1 100 ARP Table aes Route Table Save Configuration ide Internet Please follow the message on the screen during the firmware upgrade process Do not turn off the power or perform other functions during this period of time User s Manual 40 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch File Edit View Favorites Tools Help a Welcome to Switch Management Microsoft Internet Explorer TER Ay Q pack Q x a EA JO Search She Favorites Ez B7 gt 3 Address http 192 168 1 10 cgi bin switch cgi s Eco links Ca Management Switch 802 1x Other Protocols Internet User s Manual 41 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch a Welcome to Switch Management Microsoft Internet Explorer DER ay File Edit View Favorites Tools Help Q pack Q x a EA JO Search She Favorites 2 3 Address http 192 168 1 10 cqi bin switch cgi Eco inks
57. OUP 1 switch_a config bridge 1 protocol ring switch_a config User s Manual 144 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Set ring port 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to set Ring port 1 and Ring port 2 3 Command Syntax ring set port RING_PORT_1 RING_PORT_2 RING_PORT_1 Specify the Ring port 1 RING_PORT_2 Specify the Ring port 2 4 Example The following example sets the fe1 and fe2 as Ring port 1 and Ring port 2 switch_a config ring set port fe1 fe2 switch_a config User s Manual 145 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch VLAN VLAN Mode Setting 802 1Q VLAN Setting 802 1Q Port Setting Port Based VLAN 802 1Q VLAN Setting VLAN Database 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use vlan database command to enter the VLAN configuration mode 3 Command Syntax vlan database 4 Example The following example changes to VLAN configuration mode from Configure mode switch_a config vlan database switch_a config vian Add VLAN Delete VLAN 1 Command Mode VLAN Configure mode Logon to
58. Pacific Tarawa Pacific Enderbury Pacific Majuro Pacific Kwajalein Pacific Nauru Pacific Tongatapu Pacific Funafuti Pacific Wake Pacific Efate Pacific Wallis Etc GMT 12 Kwajalein UCT 13 Etc GMT 13 JST Asia Tokyo Japan KST Asia Seoul Asia Pyongyang ROK UCT 3 30 Asia Tehran Iran UCT 4 30 Asia Kabul IST 2IDT Asia Jerusalem Asia Gaza Asia Tel_ Aviv Israel CST6MEX America Cancun America Merida America Monterrey America Mexico_City America Lima Mexico General CST6 America Regina America Swift_Current Canada East Saskatchewan Canada Saskatchewan SystemV CST6 EET 2EETDST2 Europe Bucharest EET 2EETDST3 Europe Tallinn Europe Helsinki Europe Riga Europe Mariehamn EET 2EETDST2W2K Europe Istanbul UCT 14 Pacific Kiritimati Etc GMT 14 UCT9 30 Pacific Marquesas UCT12 Etc GMT 12 North America Canada PST8PDT_CA America Vancouver America Dawson_Creek America Whitehorse America Dawson Canada Pacific MST7MDT_CA America Edmonton America Yellowknife America Inuvik Canada Mountain CST6CDT_CA America Rainy_River America Winnipeg America Rankin_Inlet Canada Central User s Manual 188 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch EST5EDT_CA America Montreal America Toronto America Thunder_Bay America Nipigon America Iqaluit Canada Eastern AST4ADT_CA America Goose_Bay America Halifax America Glace_Bay Canada Atlantic North America
59. SIGNAIVAX CONNECTIVITY SYSTEMS Signamax Connectivity Systems Hardened Managed PoE Ethernet Switch Model 065 7708 LOSES Dene aa G UIDE CONNECTIVITY SYSTEMS SIG NAMAX Hardened Managed PoE Ethernet Switch Quick Start Guide This quick start guide describes how to install and use the Hardened Managed PoE Power over Ethernet Ethernet Switch This is the switch of choice for harsh environments constrained by space Physical Description The Port Status LEDs and Power Inputs pte es LI CEEE p ji 2 4 6 G 115200 8 n 1 LED State Indication 10 100BaseTX Steady A valid network connection established Link ACT Transmitting or receiving data Flashing ACT stands for ACTIVITY Steady Power Device PD is connected Off Power Device PD is disconnected 10 100 1000BaseTX 1000BaseSX LX BX Steady A valid network connection established PoE Link ACT Transmitting or receiving data Flashing ACT stands for ACTIVITY User s Manual SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch SFP Steady A valid SFP connection established Off Without SFP Power Input Assignment Power T 47 57VDC Power Ground Terminal A Block Earth Ground User s Manual SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Functional Description
60. SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch switch_a config if Switchport trunk allowed vlan 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use this command to set the switching characteristics of the Layer 2 interface to trunk The all parameter indicates that any VLAN ID is part of its port s member set The none parameter indicates that no VLAN ID is configured on this port The add and remove parameters will add and remove VLAN IDs to from the port s member set Use the no parameter to remove all VLAN IDs configured on this port 3 Command Syntax switchport trunk allowed vian all switchport trunk allowed vlan none switchport trunk allowed vlan add VLANID switchport trunk allowed vlan remove VLANID switchport trunk allowed vian except VLANID no switchport trunk vlan all Allow all VLANs to transmit and receive through the Layer 2 interface none Allow no VLANs to transmit and receive through the Layer 2 interface add Add a VLAN to transmit and receive through the Layer 2 interface remove Remove a VLAN from transmit and receive through the Layer 2 interface except All VLANs except the VLAN for which the ID is specified are part of its ports member set VLANID lt 2 4094 gt T
61. Static Secure MAC addresses per port EEE802 1x Port based Network Access Control PORT MIRRORING Port mirroring QOS IEEE802 1p Quality of Service 4 priority queues INTERNETWORKING PROTOCOLS Bridging IEEE802 1s Multiple Spanning Tree IEEE802 1w Rapid Spanning Tree IEEE802 1D Spanning Tree compatible IEEE802 1Q GVRP Ring IP Multicast IGMP Snooping Rate Control NTP NETWORK MANAGEMENT METHODS Console port access via RS 232 cable CLI Command Line Interface Telnet remote access SNMP agent MIB 2 RFC1213 Bridge MIB RFC 1493 RMON MIB RFC2819 statistics history alarm and events VLAN MIB IEEE802 1Q RFC2674 Private MIB Web browser TFTP software upgrade capability User s Manual 14 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Front Panel Display SIGNA Zonee tevin y SYSTEMS 13 95 GI 2 ae a TE we e p e Se Se 2 4 6 G2 POWER This LED comes on when the switch is properly connected to power and turned on Port Status LEDs The LEDs are located on the front panel displaying status for each respective port Please refer to the following table for more details LED State Indication 10 100BaseTX Steady A valid network connection established Link ACT Transmitting or receiving data Flashing ACT stands for ACTIVITY Steady Power Device PD is connected PoE Off Power Device PD is
62. TDST Asia Vladivostok RFT 11RFTDST RFT 12RFTDST Asia Sakhalin Asia Magadan Asia Kamchatka Asia Anadyr North America PST8PDT America Los_Angeles US Pacific New PST8PDT US Pacific SystemV PST8PDT MST7MDT America Denver America Boise America Cambridge_Bay America Shiprock MST7MDT Navajo US Mountain SystemV MST7MDT MST7 America Phoenix MST US Arizona SystemV MST7 CST6CDT America Chicago America North_Dakota Center America Menominee America Costa_Rica America Managua CST6CDT US Central SystemV CST6CDT EST5EDT America New_York America Kentucky Louisville America Kentucky Monticello America Detroit America Pangnirtung America Louisville EST5EDT US Eastern US Michigan SystemV EST5EDT AST4ADT America Thule Atlantic Bermuda SystemV AST4ADT EST5 America Coral_Harbour America Cayman America Jamaica America Panama EST Jamaica SystemV EST5 AST10ADT America Adak America Atka US Aleutian YST9YDT Canada Yukon NST3 30NDT America St_Johns Canada Newfoundland NAST3NADT America Godthab America Miquelon NASTONADT Pacific Pitcairn America Juneau America Yakutat America Anchorage America Nome US Alaska SystemV YST9YDT SystemV PST8 South America amp Central America TTST4 America Port_of_Spain SAT3 America Argentina Buenos_Aires User s Manual 184 SIGNA
63. TEMS Hardened Managed PoE Ethernet Switch Forward Delay sec 4 30 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to set the time in seconds after which if this bridge is the root bridge each port changes states to learning and forwarding Use the no parameter with this command to restore the default value 3 Command Syntax bridge GROUP forward time FORWARD_DELAY no bridge GROUP forward time GROUP lt 1 1 gt The ID of the bridge group to which this delay time is assigned FORWARD_DELAY lt 4 30 gt the forwarding time delay in seconds 4 Example The following example sets the forward time FORWARD_DELAY 30 of bridge GROUP 1 switch_a config bridge 1 forward time 30 switch_a config RSTP Port Setting Priority Granularity 16 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use this command to set the port priority for a bridge The lower priority indicates a greater likelihood of the bridge becoming root 3 Command Syntax bridge GROUP priority PRIORITY GROUP lt 1 1 gt the ID of the bridge group PRIORITY lt 0 240 gt The priority to be
64. Then click on the Login button to log on to the switch User s Manual 30 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Understanding the Browser Interface The web browser interface provides groups of point and click buttons at the left field of the screen for configuring and managing the switch A Welcome to Switch Management Microsoft Internet Explorer DER Eile Edit View Favorites Tools Help a Q sack Q x E EA Pp Search sie Favorites O 2 Address http 192 168 1 10 cgi bin switch cgi Links System name switch_a Firmware version 1 91 0 09 28 11 12 17 25 System time Thu Jan 01 18 03 36 UCT 2009 MAC address 00e0 b321 2828 Default gateway None DNS Server None VLAN ID IP Address IP Subnet Mask EA Other Protocols 1 192 168 1 10 255 255 255 0 Done Internet SYSTEM System Information System Name Password IP Address ARP Table Route Table Save Configuration Firmware Upgrade Reboot Logout PORT Configuration Port Status Rate Control RMON Statistics Per Port Vlan Activities SWITCHING Bridging Static MAC Entry Port Mirroring PoE PoE Scheduling TRUNKING Port Trunking User s Manual 31 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch STP RING Global Configuration RSTP Port Setting MSTP Properties MSTP Instance Setting MSTP Port Setting Recover Ring tm Capability VLAN VLAN Mode Setting 802 1Q VLAN Setting
65. Tools Help a Q sack Q x a Bi Search sie Favorites eB 33 Address http 192 168 1 10 cgi bin switch cgi v Go links K Management Switch System VLAN Mode Setting gt Port Switching Trunking STP Ring aH VLAN VLAN Mode Setting 02 10 VLAN Setting 02 10 Port Setting Port Based VLAN as SNMP 802 1x Other Protocols Portbased VLAN Done Internet uw MAK Maw 0 Based VLAN VLAN Choose the port to be added to or deleted from the VLAN Select all Click select all button to choose Port 1 Port 8 all to be added to the VLAN 3 Delete all Click delete all button to choose Port 1 Port 8 all to be deleted from the VLAN User s Manual 74 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 4 Submit Click Submit button when you finished Port Based VLAN setting User s Manual 75 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer Ce ay File Edit View Favorites Tools Help Q sack amp x 2 EA JO Search she Favorites 63 Address amp http 192 168 1 10 cgi bin switch cgi i Management Switch HO System HO Port Disable CoS LJDSCP Strict Priority Queue3 WRR Queue0 2 O WRR Queue0 3 Weighted Round Robin Weight 1 20 1 Global Configuration
66. X CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 3 Welcome to Switch Management Microsoft Internet Explorer Bile Edt View Favorites Tools Help Qia x ZO p search shy Fortes E herp 192 168 1 10 cg bin switch cgi Static MAC Entry Forward Add MAC address Ex 0000 1111 2222 v Staic MAC Entry Discard Add MAC address Ex 0000 1111 2222 Static MAC Entry Static MAC Entry Forward 1 Add MAC address Click in Add MAC address text box and type a locked forwarding MAC address for the port 2 VLAN ID Click VLAN ID drop down menu and choose a VLAN ID from the VLAN ID drop down list 3 Delete MAC address Click Delete MAC address drop down menu and choose a locked forwarding MAC address from the Delete MAC address drop down list to be deleted from the port 4 Submit Click Submit button when you finished Static MAC Entry Forward settings ai MAC Entry Discard Add MAC address Click in Add MAC address text box and type a MAC address to be discarded for the VLAN 2 VLAN ID VLAN ID Click VLAN ID drop down menu and choose a VLAN ID from the VLAN ID drop down list 3 Delete MAC address Click Delete MAC address drop down menu and choose a MAC address from the Delete MAC address drop down list to be discarded from the VLAN 4 Submit Click Submit button when you finished Static MAC En
67. Y SYSTEMS Hardened Managed PoE Ethernet Switch Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use flowcontrol on command to enable flow control and configure the flow control mode for the port Use the no flowcontrol to disable this function 3 Command Syntax flowcontrol on no flowcontrol 4 Example The following example shows the use of flowcontrol on to the interface fe1 port 1 switch_a config interface fe1 switch_a config if flowcontrol on switch_a config if Port Status 1 Command Mode Exec mode or Privileged Exec mode Logon to Exec Mode View Mode or Privileged Exec Mode Enable Mode The switch_a gt or switch_a prompt will show on the screen switch_a gt switch_a 2 Usage Use the show interface command to display interface configuration and status 3 Command Syntax show interface IFNAME IFNAME specifies the name of the interface for which status and configuration information is desired 4 Example The following example shows the use of show interface to display interface configuration and status of the interface fe1 port 1 switch_a gt show interface fe1 User s Manual 119 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Rate Control 1 Command Mode Interface mode Logon t
68. a config if 2 Usage Use ip igmp snooping report suppression command to enable report suppression for IGMP versions 1 and 2 Use the no ip igmp snooping report suppression command to disable report suppression 3 Command Syntax no ip igmp snooping report suppression 4 Example The following example enables report suppression for IGMPv2 reports on vian1 1 switch_a config interface vian1 1 switch_a config if ip igmp version 2 switch_a config if ip igmp snooping report suppression switch_a config if NTP RTC Time 1 Command Mode Exec mode or Privileged Exec mode Logon to Exec Mode View Mode or Privileged Exec Mode Enable Mode The switch_a gt or switch_a prompt will show on the screen switch_a gt switch_a 2 Usage Use the show rtc time command to show RTC time 3 Command Syntax show rtc time 4 Example The following example shows the use of show rtc time to show RTC time switch_a gt show rtc time User s Manual 176 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Adjust RTC Time 1 Command Mode Privileged Exec mode Logon to Privileged Exec Mode Enable Mode The switch_a prompt will show on the screen switch_a 2 Usage Use this command to configure the time of RTC 3 Command Syntax set clock YEAR MONTH DAY HOUR MINUTE SECOND YEAR Specifies year from 2000 to 2037 MONTH lt 1
69. ack Q x a CA gt Search Sig Favorites far B 3 Address http 192 168 1 10 cgi bin switch cgi E3co Links Management Switch FG System System Name System Information System Name Password Update Setting IP Address ARP Table Route Table Save Configuration Firmware Upgrade Retype Password Password Update Setting C Other Protocols Done Internet System Name Password 1 System Name Click in System Name text box Type a system name if it is blank or replace the current system name with a new one 2 Updating Setting Click Updating Setting button to update your settings 3 Password Click in Password text box Type a password 4 Retype Password Click in Retype Password text box Type the same password in Password text box again to verify it 5 Updating Setting Click Updating Setting button to update your settings User s Manual 34 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch A Welcome to Switch Management Microsoft Internet Explorer Cel ay File Edit View Favorites Tools Help Q Back jress http 192 168 1 10 cgi bin switch cgi Links K Management Switch EQ System IP Address IP Subnet Mask System Information System Name Password 192 168 1 10 255 255 255 0 IP Address ARP Tate Route Table Save Configuration Disable v Firmware Uperade
70. all Install to flash logout Exit from the EXEC no Negate a command or set its defaults ping Send echo messages quit Fxit current mode and down to previous mode reload Reboot the system restore lo restore the default setting show Show running system information telnet Open a telnet connection terminal Set terminal line parameters traceroute Trace route to destination undebug Disable debugging functions see also debug write Write switch_at_ Connected 0 03 01 VT100 115200 6 11 At the switch_a prompt just type in the full or partial command string then typing a question mark to display the command keywords or parameters along with a short description switch_a show 115200 HyperTerminal File Edit View Call Transfer Help es goog all if Brand ID bridge protocol Show CLI tree of current mode debugging Debugging functions see also undebug etherchannel NCP channel commands flowcontrol IFEF 802 3x Flow Control gmrp Generic Attribute Registration Protocol gvrp GARP Vlan Registration Protocol hardware Hardware configuration history Display the session command history interface The layer interfaces ip Internet Protocol IP lacp LACP commands lacp counter LACP commands ist Show command lists mac Mac address memory Hemory information mirror Port Nirporing mls Switch nse NSH More Connected 0 03 49 T1003 115200 8 N 1 User s Manual 101 SIGNAMAX CONNECTIVITY SYSTEMS
71. all Transfer Help Oe s3 op e switch_a login root Switch version 1 30 r142 sdkr32 12 05 07 13 59 04 switch_a gt enable switch i i Vty connection is timed out switch a login Login timed out after 60 seconds switch_a login root Switch version 1 30 r142 sdkr32 12 05 07 13 59 04 switch a gt Connected 0 20 00 T1003 115200 8 N 1 Exit from Privileged Exec Mode or Enable Mode At the switch_a prompt just type in exit and press lt Enter gt to exit from Privileged Exec Mode or Enable Mode switch_a exit 115200 HyperTerminal File Edit View Call Transfer Help Owe es OD g switch_a login root Switch version 1 30 r142 sdkr32 12 05 07 13 59 06 switch _a gt enable switch_atexit switch_a login _ Connected 0 20 55 VT100 115200 6 Nei User s Manual 103 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Configure Mode Configure Terminal Mode Logon to Configure Mode Configure Terminal Mode At the switch_a prompt just type in configure terminal and press lt Enter gt to logon to Configure Mode or Configure Terminal Mode And the switch_a config prompt will show on the screen switch_a configure terminal 115200 HyperTerminal File Edit View Call Transfer Help Oe es op GF switch_a login root Switch version 1 30 r142 sdkr32 12 05 07 13 59 04 switch _a gt enable switch_aticonfigure terminal Enter configuration commands
72. ames can only be received 4 Example The following example sets the switchport mode hybrid of the interface fe1 port 1 and all frames to be received on interface fe1 port 1 switch_a config interface fe1 switch_a config if switchport mode hybrid acceptable frame type all switch_a config if Switchport mode trunk 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use switchport mode trunk command to set the switching characteristics of the Layer 2 interface as trunk and specify only tagged frames Use the no switchport trunk command to reset the mode of the Layer 2 interface to access default 3 Command Syntax switchport mode trunk no switchport trunk 4 Example User s Manual 148 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch The following example sets the switchport mode trunk of the interface fe1 ort 1 switch_a config interface fe1 switch_a config if switchport mode trunk switch_a config if Switchport hybrid allowed vlan 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interfa
73. an Mayotte Africa Mogadishu Africa Khartoum Africa Dar_es_ Salaam Africa Kampala Antarctica Syowa Asia Bahrain Asia Kuwait Asia Qatar Asia Riyadh Asia Aden Etc GMT 3 UCT 4 Indian Mauritius Indian Reunion Indian Mahe Asia Muscat Etc GMT 4 UCT 5 Indian Kerguelen Indian Maldives Asia Karachi Asia Dushanbe Asia Ashgabat Asia Samarkand Asia Tashkent Etc GMT 5 UCT 5 45 Asia Katmandu UCT 6 Antarctica Mawson Antarctica Vostok Asia Dhaka Asia Thimphu Indian Chagos Asia Colombo Etc GMT 6 Asia Dacca Asia Thimbu UCT 6 30 Asia Rangoon Indian Cocos UCT 7 Antarctica Davis Asia Phnom_Penh Asia Jakarta Asia Pontianak Asia Vientiane Asia Bangkok Asia Saigon Indian Christmas Etc GMT 7 UCT 8 Antarctica Casey Asia Brunei Asia Taipei Asia Makassar Asia Manila User s Manual 187 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Asia Singapore Etc GMT 8 Asia Ujung_Pandang Singapore UCT 9 Asia Dili Asia Jayapura Pacific Palau Etc GMT 9 UCT 9 30 Australia Darwin Australia North UCT 10 Antarctica DumontDUrville Pacific Guam Pacific Saipan Pacific Truk Pacific Noumea Pacific Port_Moresby Etc GMT 10 Pacific Yap UCT 11 Pacific Ponape Pacific Kosrae Pacific Guadalcanal Etc GMT 11 UCT 11 30 Pacific Norfolk UCT 12 Pacific Fiji
74. avorites Tools Help Q Back Q x a H K Search She Favorites ahd BS 3 Address http 192 168 1 10 cgi bin switch cgi v B co Links Gv Management Switch o gt System Please relogin Relogin System Information System Name Password IP Address ARP Table Route Table Save Configuration ide Internet Logout Logout Click Logout button to logout of the switch User s Manual 45 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help Back x lt Search Favorites 4 62 gt 2 X s 7 F Address http 192 168 1 10 cgi bin switch cgi ed Go K Management Switch FE System Flow control amp Port a Enable onfiguration Port Status Enable Rate Control y yi Enable FE Switching EO Trunking HO STP Ring 7 Enable HO VLAN FE QoS 4 SNMP Enable v FC 8021x Other Protocols Enable Enable Enable Done Internet Configuration 1 Admin Setting Click Admin Setting drop down menu to choose Link down or Link up from the Admin Setting drop down list to disable or enable Admin Setting for the port 2 Speed Click Speed drop down menu to change the line speed and duplex settings from the Speed drop down list for the port 3 Flow control Click Flow control drop down menu to choo
75. ber of seconds of persistence 4 Example The following example sets the new AGEINGTIME 1000 to bridge GROUP 1 switch_a config bridge 1 ageing time 1000 switch_a config Threshold level 0 100 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use storm control level command to specify the rising threshold level for broadcasting multicast or destination lookup failure traffic The storm contro action occurs when traffic utilization reaches this level 3 Command Syntax storm control level LEVEL User s Manual 122 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch LEVEL lt 0 100 gt specifies the percentage of the threshold percentage of the maximum speed pps of the interface 4 Example The following example shows setting storm control level LEVEL 30 to the interface fe1 port 1 switch_a config interface fe1 switch_a config if storm control level 30 switch_a config if Broadcast 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2
76. ce fe1 switch_a config if 2 Usage Use this command to set the switching characteristics of the Layer 2 interface to hybrid Both tagged and untagged frames will be classified over hybrid interfaces Use the no parameter to turn off allowed hybrid switching 3 Command Syntax switchport hybrid allowed vlan all switchport hybrid allowed vian none switchport hybrid allowed vlan add VLANID egress tagged enable disable switchport hybrid allowed vlan remove VLANID no switchport hybrid vlan all Allow all VLANs to transmit and receive through the Layer 2 interface none Allow no VLANs to transmit and receive through the Layer 2 interface add Add a VLAN to the member set remove Remove a VLAN from the member set VLANID lt 2 4094 gt The ID of the VLAN or VLANs that will be added to or removed from the Layer 2 interface For a VLAN range specify two VLAN numbers lowest then highest number in the range separated by a hyphen For a VLAN list specify the VLAN numbers separated by commas egress tagged enable Enable the egress tagging for the outgoing frames disable Disable the egress tagging for the outgoing frames 4 Example The following example specifies to add the interface fe1 port 1 to VLANID 2 and enable the egress tagged for the outgoing frames on interface fe1 ort 1 switch_a config interface fe1 switch_a config if switchport hybrid allowed vlan add 2 egress tagged enable User s Manual 149
77. ch_a login root Switch version 1 30 r142 sdkr32 12 09 07 13 99 04 swi tch_a gt Connected 0 38 30 VT100 115200 amp N 1 Exit from Configure Mode or Configure Terminal Mode At the switch_a config prompt just type in exit and press lt Enter gt to exit from Configure Mode or Configure Terminal Mode switch_a config exit 115200 HyperTerminal File Edit View Call Transfer Help Owe es OD g switch_a login root Switch version 1 30 r142 sdkr32 12 05 07 13 59 06 switch a gt enable switch_altconfigure terminal g Enter configuration commands one per line End with CNTL Z switch_a config Hexit switch a _ Connected 0 40 23 VT100 115200 8 N 1 User s Manual 107 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch System Information System Name Password IP Address ARP Table Route Table Save Configuration Firmware Upgrade Reboot Logout System Name Password System Name 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use hostname command to set or change the network server name Use the no hostname command to disable this function 3 Command Syntax no hostname HOSTNAME HOSTNAME specifies the network name of the system 4 Example The following example sets the hostname to switch and shows the change in the prompt
78. d to disable warm start trap for SNMP 3 Command Syntax no snmp server trap type enable warmStart 4 Example The following example enables warm start trap for SNMP switch_a config snmp server trap type enable warmStart switch_a config Link Down Trap 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode User s Manual 158 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch The switch_a config prompt will show on the screen switch_a config 2 Usage Use snmp server trap type enable linkDown command to enable link down trap for SNMP Use the no snmp server trap type enable linkDown command to disable link down trap for SNMP 3 Command Syntax no snmp server trap type enable linkDown 4 Example The following example enables link down trap for SNMP switch_a config snmp server trap type enable linkDown switch_a config Link Up Trap 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use snmp server trap type enable linkUp command to enable link up trap for SNMP Use the no snmp server trap type enable linkUp command to disable link up trap for SNMP 3 Command Syntax no snmp server trap type enable linkUp 4 Example The following example enables link up trap for SNMP switch_a conf
79. d to disable the Spanning Tree protocol on a bridge 3 Command Syntax bridge GROUP spanning tree enable no bridge GROUP spanning tree enable BRIDGE FORWARD GROUP lt 1 1 gt Bridge group name used for bridging BRIDGE FORWARD Puts all ports of the specified bridge into the forwarding state 4 Example The following example enables or disables the spanning tree on bridge GROUP 1 switch_a config bridge 1 spanning tree enable switch_a config no bridge 1 spanning tree enable bridge forward switch_a config Bridge Priority 0 61440 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to set bridge priority for the common instance Using a lower priority indicates a greater likelihood of the bridge becoming root 3 Command Syntax bridge GROUP priority PRIORITY no bridge GROUP priority GROUP lt 1 1 gt The ID of the bridge group for which the priority is set PRIORITY lt 0 61440 gt The bridge priority 4 Example The following example sets the priority PRIORITY 4096 of bridge GROUP 1 switch_a config bridge 1 priority 4096 switch_a config Hello Time sec 1 9 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen User s Manual 134 SIGNAMAX
80. de The switch_a prompt will show on the screen switch_a User s Manual 112 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 2 Usage Use restore default command to restore default setting of the switch 3 Command Syntax restore default 4 Example The following example restores default setting of the switch switch_a restore default switch_a Auto Save 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to enable auto save configuration function The configuration will be automatically saved at every configured interval while this command is enabled Use the no form of this command to disable this feature 3 Command Syntax service auto config enable no service auto config enable 4 Example The following example enables or disables auto save configuration to switch switch_a config service auto config enable switch_a config no service auto config enable switch_a config Auto Save Interval 5 65536 sec 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to set the interval when the configuration would be automatically saved The range of interval value
81. disconnected 10 100 1000BaseTX 1000BaseSX LX BX Steady A valid network connection established Link ACT Transmitting or receiving data Flashing ACT stands for ACTIVITY ee Steady A valid SFP connection established Off Without SFP Physical Ports The Hardened Managed Ethernet Switch provides 4 port PoE 10 100BaseTX 2 port 10 100BaseTX 2 10 100 1000BaseTX amp Gigabit SFP combo ports Hardened Managed Ethernet Switch User s Manual 15 CONNECTIVITY SYSTEMS gt Hardened Managed PoE Ethernet Switch CONNECTIVITY e RJ 45 connectors on TX ports e Duplex LC connector on SFP 1000BaseSX LX BX fiber transceiver MODE SELECTION 10BaseT full duplex mode 10BaseT half duplex mode 100BaseTX full duplex mode 100BaseTX half duplex mode 1000BaseT SX LX BX full duplex mode Auto negotiating mode User s Manual 16 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Switch Management Web based browser interface The switch also boasts a point and click browser based interface that lets user access full switch configuration and functionality from a Netscape or Internet Explorer browser Administration console via RS 232 serial port CLI The switch provides an onboard serial port which allows the switch to be configured via a directly connected terminal External SNMP based network management application The switch can also be configured via SNMP
82. e 0 0 switch_a config if User s Manual 130 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Port Trunking Port Trunking 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fel means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use static channel group command to create a static aggregator or add a member port to an already existing static aggregator Use the no static channel group command to detach the port from the static aggregator 3 Command Syntax static channel group lt 1 8 gt no static channel group lt 1 8 gt Channel group number Maximum 8 ports in static channel group 1 to 6 Maximum 4 ports in static channel group 7 and 8 4 Example The following example adding the interface fel port 1 to static channel group 1 switch_a config interface fe1 switch_a config if static channel group 1 switch_a config if User s Manual 131 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch STP Ring Global Configuration RSTP Port Setting MSTP Properties MSTP Instance Setting MSTP Port Setting Recover Ring tm Capability Global Configuration STP Version 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will
83. e is a region by itself unless specifically added to one 3 Command Syntax bridge GROUP region REGION_NAME no bridge GROUP region GROUP lt 1 1 gt Specify the bridge group ID REGION_NAME Specify the name of the region 4 Example The following example creates an MST region and specifies a name regionname to it in bridge GROUP 1 User s Manual 139 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Switch_a config spanning tree mst configuration switch_a config mst bridge 1 region regionname switch_a config mst Revision Level 1 Command Mode MST Configuration mode Logon to Configure Mode Configure Terminal Mode Then logon to MST Configuration mode The switch_a config mst prompt will show on the screen switch_a config spanning tree mst configuration switch_a config mst 2 Usage Use this command to specify the number for configuration information The default value of revision number is 0 3 Command Syntax bridge GROUP revision REVISION_NUM GROUP lt 1 1 gt Specify the bridge group ID REVISION_NUM lt 0 255 gt Revision number 4 Example The following example specifies a revision number 25 of MST configuration in bridge GROUP 1 switch_a config spanning tree mst configuration switch_a config mst bridge 1 revision 25 switch_a config mst Max Hops 1 Command Mode Configure mode Logon to Configure Mode Configure Ter
84. e new IP address 192 168 1 10 and new IP subnet mask 255 255 255 0 to switch switch_a config interface vian1 1 switch_a config if ip address 192 168 1 10 24 switch_a config if Default Gateway 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use ip default gateway command to set the IP address of the default gateway Use the no ip default gateway command to remove the IP address of the default gateway User s Manual 109 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 3 Command Syntax ip default gateway IP ADDRESS no ip default gateway IP ADDRESS A B C D specifies the IP address of the default gateway 4 Example The following example sets the default gateway 192 168 1 254 to switch switch_a config ip default gateway 192 168 1 254 switch_a config DNS Server 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use ip dns command to set the IP address of the DNS server Use the no ip dns command to remove the IP address of the DNS server 3 Command Syntax ip dns IP ADDRESS no ip dns IP ADDRESS A B C D specifies the IP address of the DNS server 4 Example The following example sets the DNS server 192 1
85. ead write access mode and MD5 authentication mypassword switch_a config snmp server v3 user myuser rw auth md5 mypassword switch_a config SNMPvs Priv Auth MD5 SNMPv3 Priv Auth SHA 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config User s Manual 162 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 2 Usage Add a user using snmp v3 with read only or read write access mode MD5 or SHA authentication and privacy Use the no form of the command to delete this user 3 Command Syntax no snmp server v3 user USERNAME ro rw priv auth md5 sha AUTH PASSWORD des PRIV_PASS_ PHRASE USERNAME Specify a user name ro read only access mode rw read write access mode md5 authentication method sha authentication method AUTH_PASSWORD authentication password PRIV_PASS_PHRASE encryption pass phrase 4 Example The following example adds a user myuser using snmp v3 with read write access mode MD5 authentication mypassword and encryption pass phrase mypassphrase switch_a config snmp server v3 user myuser rw priv md5 mypassword des mypassphrase switch_a config User s Manual 163 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Radius Configuration Port Authentication Radius Configuration Radius Status 1 Command Mode Con
86. ecify an authentication password e SNMPv3 Auth SHA Add a user using SNMP v3 with authentication Click in the Auth Password textbox and specify an authentication password e SNMPv3 Priv Auth MD5 Add a user using SNMP v3 with authentication and privacy Click in the Auth Password textbox and specify an authentication password Click in the Privacy PassPhrase textbox and specify a privacy pass phrase e SNMPv3 Priv Auth SHA Add a user using SNMP v3 with authentication and privacy Click in the Auth Password textbox and specify an authentication password Click in the Privacy User s Manual 82 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch PassPhrase textbox and specify a privacy pass phrase 3 User Name Click in the User Name textbox and specify a user name for user using SNMP v3 4 Access Mode Click Access Mode drop down menu from Access Mode drop down list to choose Read Only or Read Write e Read Only Add a user using SNMP v3 with read only access mode e Read Write Add an user using SNMP v3 with read write access mode 5 Submit Click Submit button when you finished SNMP V3 Setting Welcome to Switch Management Microsoft Internet Explorer DER File Edit View Favorites Tools Help a Q sack Q x a EA p gt Search sie Favorites O 33 Address a http 192 168 1 10 cgi bin switch cgi vE co links oe ohh k m m JE E
87. em port to the current administration console session The console appears to be directly connected to the external modem Web Management The switch provides a browser interface that lets you configure and manage the switch remotely After you set up your IP address for the switch you can access the switch s web interface applications directly in your web browser by entering the IP address of the switch You can then use your web browser to list and manage switch configuration parameters from one central location just as if you were directly connected to the switch s console port SNMP Based Network Management You can use an external SNMP based application to configure and manage the switch This management method requires the SNMP agent on the switch and the SNMP Network Management Station to use the same community string This management method in fact uses two community strings the get community string and the set community string If the SNMP Network management station only knows the set community string it can read and write to User s Manual 23 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch the MIBs However if it only Knows the get community string it can only read MIBs The default get and set community strings for the switch are public Protocols The switch supports the following protocols VIRTUAL TERMINAL PROTOCOLS SUCH AS TELNET A virtual terminal protocol is a software pro
88. enable or disable GVRP registration to the port Configuring an IEEE802 1Q trunk port in registration mode allows dynamic creation if dynamic VLAN creation is enabled registration and deregistration of VLANs on the trunk port Update Setting Click Update Setting button when you finished Per port setting User s Manual 89 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 4 Welcome to Switch Management Microsoft Internet Explorer BAE File Edit View Favorites Tools Help Q ax Q x a H By Search she Favorites amp A7 amp 33 ddress http 192 168 1 10 cgi bin switch cgi vE co links Ge Management Switch System IGMP mode Passive v O Port cr HO Switching Update Setting Cp Trunking STP Ring HE VLAN VLAN ID _e a os IGMP version 3 inal HO SNMP 802 1x E Other Protocols GVRP max response time 1 240 IGMP Snooping report suppression Enable fast leave Disable v query interval 10 18000 Update Setting Internet a Snooping IGMP mode Click IGMP mode drop down menu from IGMP mode drop down list to choose Disable Passive or querier for the switch Disable Disable IGMP on the switch Passive The switch with only multicast data forwarding capability Querier The switch acts as the querier for the network There is only one querier on a network at any time 2 Update Setting Click Update Setting bu
89. ew Favorites Tools Help Qa x AO J Search Fe Favorites R MEE S Address 48 http 192 168 1 10 cgi bin switch cgi v B co Links kbps Port Status kbps Rate Control kbps RMON Statistics Per Port Vian Activities kbps Switching bps Trunking HO STP Ring kbps VLAN 1 as kbps H E SNMP kbps 802 1 a Update Setting FC Other Protocols Internet Rate Control 1 Ingress Click in Ingress text box and type a new Rate to change the Ingress Rate Control for the port Rate Values 64kbps 128kbps 192kbps 1792kbps 2Mbps 3Mbps 4Mbps 100Mbps 104Mbps 112Mbps 120Mbps 1000Mbps lt Note gt M 1024k 2 Egress Click in Egress text box and type a new Rate to change the Egress Rate Control for the port Rate Values 64kbps 128kbps 192kbps 1792kbps 2Mbps 3Mbps 4Mbps 100Mbps 104Mbps 112Mbps 120Mbps 1000Mbps lt Note gt M 1024k 3 Update Setting Click Update Setting button when you finished these Rate Control settings User s Manual 49 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch A Welcome to Switch Management Microsoft Internet Explorer Ce ar Eile Edit View Favorites Tools Help Q Back S x a w J Searc KX avorites amp F amp Gi gt Links B co amp Address http 192 168 1 10 cgi bin switch cgi K Management Switch EO Sys
90. ey do not enclose the key in quotaion marks unless the quotation marks themselves are part of the key 5 Timeout lt 1 1000 gt Click in the Timeout textbox and specify the time interval in seconds that the Switch waits for the radius server to reply before retransmitting Enter a value in the range 1 to 1000 6 Retransmit lt 1 100 gt Click in the Retransmit textbox and specify the number of times a radius request is resent to a server if that server is not responding or responding slowly Enter a value in the range 1 to 100 7 Submit Click Submit button when you finished Radius Server Setting User s Manual 85 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch i Welcome to Switch Management Microsoft Internet Explorer SEE File Edit View Favorites Tools Help a Q sac Q x a A p gt Search sie Favorites O B amp 33 Address http 192 168 1 10 cgi bin switch cgi E3co ilinks Q Port HC Switching Trunking E STP Ring VLAN Qos SNMP ENG 8021x Radius Configuration Port Authentication H Other Protocols Done Internet Delete Radius 1 Delete Radius Click Delete Radius button The Select Radius Server IP window appears 2 Select Radius Server IP Click Select Radius Server IP drop down menu from Select Radius Server IP drop down list to choose the IP address of the remote radius server host to be
91. figuration MSTP Port Setting Recover Ring tm Capability VLAN Qs SNMP BC 802 1x H Other Protocols Done Internet Recover Ring tm Capability Ring state 1 Click Ring state drop down menu from Ring state drop down list to choose Enable or Disable to enable or disable Ring state 2 Update Setting Click Update Setting button when you finished Ring state setting Set ring port 1 Ring port 1 Click Ring port 1 drop down menu to choose Ring port 1 from Ring port 1 drop down list 2 Ring port 2 Click Ring port 2 drop down menu to choose Ring port 2 from Ring port 2 drop down list User s Manual 68 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 3 Update Setting Click Update Setting button when you finished Set ring port User s Manual 69 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch VLAN Welcome to Switch Management Microsoft Internet Explorer DEAR a File Edit View Favorites Tools Help Q sack x e cA Ms Search sie Favorites OG 6B 3 Address http 192 168 1 10 cgi bin switch cgi vE co ilink Management Switch Systeni VLAN Mode Setting Port pis Tag based VLAN CD Switching 02 10 VLAN Setti 02 tting Port Based VLAN Qs H SNMP HC 802 1x H O Other Protocols amp Done Internet VLAN Mode Setting
92. figure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use dot1x system auth ctrl command to globally enable authentication Use no dot1x system auth ctrl command to globally disable authentication 3 Command Syntax no dot1x system auth ctrl 4 Example The following example globally enables authentication switch_a config dot1x system auth ctrl switch_a config Radius Server IP Radius Server Port 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to specify the IP address of the remote radius server host and assign authentication and accounting destination port number 3 Command Syntax no radius server host IP ADDRESS auth port PORT IP ADDRESS A B C D specifies the IP address of the radius server host PORT specifies the UDP destination port for authentication requests The host is not used for authentication if set to 0 4 Example The following example specifies the IP address 192 168 1 100 of the remote radius server host and assigns authentication and accounting User s Manual 164 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch destination port number 1812 switch_a config radius server host 192 168 1 100 auth por
93. following example shows the use of show interface statistics to display RMON statistics of the interface fe1 port 1 switch_a gt show interface statistics fe1 Per Port Vlan Activities 1 Command Mode Exec mode or Privileged Exec mode Logon to Exec Mode View Mode or Privileged Exec Mode Enable Mode The switch_a gt or switch_a prompt will show on the screen switch_a gt switch_a 2 Usage Use show vlan command to display information about a particular VLAN by specifying the VLAN ID 3 Command Syntax show vlan lt 2 4094 gt lt 2 4094 gt VLAN ID 4 Example The following is an output of show vlan command displaying information about VLAN 2 switch_a gt show vlan 2 User s Manual 121 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Bridging Static MAC Entry Port Mirroring PoE PoE Scheduling Bridging Aging Time seconds 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to specify an ageing out time for a learned MAC address The learned MAC address will persist till this specified time 3 Command Syntax Bridge GROUP ageing time AGEINGTIME no bridge GROUP ageing time Group lt 1 1 gt The ID of the bridge group that this ageing time is for AGEINGTIME lt 10 1000000 gt The num
94. g Setting Daylight Saving Mode Disable Tine Set Offset 1 1440 min Name of Daylight Saving Timezone Weekday Month Jan Day Sun How To Month Jan Day Sun Hour From From Month Jan y Hour Minte To Month Jan y How Minute Update Sesing NTP Adjust RTC Time 1 Click in textbox and specify the Year Month Day Hour Minute and Second 2 Update Setting Click Update Setting button when you finished Adjust RTC Time NTP Setting 1 NTP Status Click NTP Status drop down menu from NTP Status drop down list to choose Enable or Disable to enable or disable NTP for the Switch 2 NTP Server IP Address or Domain name Click in the NTP Server textbox and specify the IP address or Domain name of NTP server 3 Sync Time Click Sync Time button to synchronize time with NTP User s Manual 92 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch server 4 Time Zone Click Time Zone drop down menu from Time Zone drop down list to set time zone 5 Polling Interval 1 10080 min Click in the Polling Interval textbox and specify the polling interval 6 Update Setting Click Update Setting button when you finished NTP Setting Daylight Saving Setting 1 Daylight Saving Mode Click Daylight Saving Mode drop down menu from Daylight Saving Mode drop down list to choose Disable Weekday or Date to choose disable weekday o
95. g example specifies the polling interval 60 minutes switch_a config ntp polling interval 60 switch_a config Daylight Saving Mode 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to enable daylight saving Use no clock summer time command to disable daylight saving 3 Command Syntax clock summer time TIMEZONE weekday WEEK DAY MONTH HOUR MINUTE WEEK DAY MONTH HOUR MINUTE OFFSET TIMEZONE Specifies the daylight saving timezone User s Manual 179 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch WEEK lt 1 5 gt Specifies starting ending week of daylight savings time DAY lt 0 6 gt Specifies from Sunday to Saturday MONTH lt 1 12 gt Specifies from January to December HOUR lt 0 23 gt Specifies from 0 to 23 MINUTE lt 0 59 gt Specifies from 0 to 59 OFFSET lt 1 1440 gt Specifies from 1 to 1440 minutes clock summer time TIMEZONE date DAY MONTH HOUR MINUTE DAY MONTH HOUR MINUTE OFFSET TIMEZONE Specifies the daylight saving timezone DAY lt 1 31 gt Specifies from 1 to 31 MONTH lt 1 12 gt Specifies from January to December HOUR lt 0 23 gt Specifies from 0 to 23 MINUTE lt 0 59 gt Specifies from 0 to 59 OFFSET lt 1 1440 gt Specifies from 1 to 1440 minutes no clock summer time 4 Example The following example set
96. ge GROUP 1 switch_a config bridge 1 multiple spanning tree enable switch_a config no bridge 1 multiple spanning tree enable bridge forward switch_a config Rapid Spanning Tree Protocol 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to enable the Rapid Spanning Tree protocol on a bridge Use the no form of the command to disable the Rapid Spanning Tree protocol on a bridge 3 Command Syntax bridge GROUP rapid spanning tree enable no bridge GROUP rapid spanning tree enable BRIDGE FORWARD GROUP lt 1 1 gt Bridge group name used for bridging BRIDGE FORWARD Puts all ports of the specified bridge into the forwarding state 4 Example The following example enables or disables the rapid spanning tree on bridge GROUP 1 switch_a config bridge 1 rapid spanning tree enable switch_a config no bridge 1 rapid spanning tree enable bridge forward switch_a config Spanning Tree Protocol 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage User s Manual 133 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Use this command to enable the Spanning Tree protocol on a bridge Use the no form of the comman
97. grade Europe Madrid Africa Ceuta Europe Stockholm Europe Vatican Europe San_Marino Arctic Longyearbyen Atlantic Jan_Mayen Europe Ljubljana Europe Sarajevo Europe Skopje Europe Zagreb Europe Bratislava Poland EET 2EETDST Asia Nicosia EET Europe Minsk Europe Sofia Europe Athens Europe Vilnius Europe Chisinau Europe Istanbul Europe Kiev Europe Uzhgorod Europe Zaporozhye Europe Nicosia Asia Istanbul Europe Tiraspol Turkey GMTOBST Europe London Europe Dublin Eire Europe Belfast GB GB Eire WETOWETDST WET Atlantic Faeroe Atlantic Madeira Atlantic Canary PWTOPST Europe Lisbon Portugal MST 3MDT Europe Moscow W SU EUT 1EUTDST America Scoresbysund Atlantic Azores EUT 2EUTDST Asia Beirut Europe Simferopol EUT 3EUTDST Asia Tbilisi EUT 4EUTDST Europe Samara EUT 6EUTDST Asia Almaty Asia Qyzylorda EUT 8EUTDST Asia Ulaanbaatar Russian Federation RFT 2RFTDST Europe Kaliningrad RFT 3RFTDST Europe Moscow RFT 4RFTDST Asia Yerevan Asia Baku Asia Oral Asia Ashkhabad User s Manual 183 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch RFT 5RFTDST Asia Aqtobe Asia Aqtau Asia Bishkek Asia Yekaterinburg RFT 6RFTDST Asia Omsk Asia Novosibirsk RFT 7RFTDST Asia Hovd Asia Krasnoyarsk RFT 8RFTDST Asia Irkutsk Asia Chungking Asia Ulan_Bator RFT 9RFTDST Asia Choibalsan Asia Yakutsk RFT 10RF
98. gram such as Telnet that allows you to establish a management session from a Macintosh a PC or a UNIX workstation Because Telnet runs over TCP IP you must have at least one IP address configured on the switch before you can establish access to it with a virtual terminal protocol lt Note gt Terminal emulation is different from a virtual terminal protocol in that you must connect a terminal directly to the console port SIMPLE NETWORK MANAGEMENT PROTOCOL SNMP SNMP is the standard management protocol for multivendor IP networks SNMP supports transaction based queries that allow the protocol to format messages and to transmit information between reporting devices and data collection programs SNMP runs on top of the User Datagram Protocol UDP offering a connectionless mode service Management Architecture All of the management application modules use the same Messaging Application Programming Interface MAPI By unifying management methods with a single MAPI configuration parameters set using one method e g console port are immediately displayed the other management methods e g SNMP agent of web browser The management architecture of the switch adheres to the IEEE open standard This compliance assures customers that the switch is compatible with and will interoperate with other solutions that adhere to the same open standard User s Manual 24 SIGNAMA y Hardened Managed PoE Ethernet Switch Web Based Browser
99. gt to list the commands switch_a 115200 HyperTerminal File Edit View Call Transfer Help De s3 op e switch_a gt enable switch_all Exec commands clear Clear the Forwarding database configure Enter configuration mode Copy from one file to another Debugging functions see also undebug disable Turn off privileged mode command enable Turn on privileged mode command exit End current mode and down to previous mode help Description of the interactive help system install Install to Flash logout Exit from the EXEC Negate a command or set its defaults Send echo messages Exit current mode and down to previous mode Reboot the system To restore the default setting Show running system information Open a telnet connection terminal Set terminal line parameters traceroute Trace route to destination undebug Disable debugging functions see also debug More Connected 0 02 20 VT100 1152008 W User s Manual 100 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 115200 HyperTerminal File Edit View Call Transfer Help es ape Exec commands clear Clear the Forwarding database configure Enter configuration mode copy Copy from one file to another debug Debugging functions see also undebug disable Jurn off privileged mode command enable Turn on privileged mode command exil End current mode and down to previous mode help Description of the interactive help system inst
100. h The following example specifies 20 seconds for the Switch to wait for a server host to reply before timing out switch_a config radius server timeout 20 switch_a config Retransmit 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to specify the number of times the Switch transmits each radius request to the server before giving up 3 Command Syntax radius server retransmit RETRIES no radius server retransmit RETRIES lt 1 100 gt Specifies the retransmit value Enter a value in the range 1 to 100 4 Example The following example specifies the retransmit value 12 switch_a config radius server retransmit 12 switch_a config Port Authentication Authentication State 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use dot1x reauthetication command to enable reauthentication on a port Use no dot1x reauthetication command to disable reauthentication on a port 3 Command Syntax no dot1x reauthentication User s Manual 166 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 4 Example The follo
101. h OVERVIEW 26 SNMP AGENT AND MIB 2 RFC 1213 27 RMON MIB RFC 2819 AND BRIDGE MIB RFC 1493 27 RMON Groups Supported 28 Bridge Groups Supported 28 Web Based Browser Management 29 LOGGING ON TO THE SWITCH 29 UNDERSTANDING THE BROWSER INTERFACE 31 SYSTEM 33 PORT 46 SWITCHING 52 TRUNKING 59 STP RING 60 VLAN 70 Qos 76 SNMP 79 802 1x 84 OTHER PROTOCOLS 88 Command Line Console Management 94 ADMINISTRATION CONSOLE 94 Exec Mode View Mode 95 Privileged Exec Mode Enable Mode 99 Configure Mode Configure Terminal Mode 104 SYSTEM 108 PORT 117 SWITCHING 122 TRUNKING 131 STP RING 132 VLAN 146 QoS 152 SNMP 155 802 1x 164 OTHER PROTOCOLS 169 Specifications 181 Appendix A 182 Appendix B 183 Contact Information 190 User s Manual 11 AMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Product Overview Hardened Managed Ethernet Switch o E 2 3 4 5 6 RE R E R coc G1 G2 2 4 6 G2 Front View Package Contents When you unpack the product package you shall find the items listed below Please inspect the contents and report any apparent damage or missing items immediately to your authorized reseller e This Switch e User s Manual e RS 232 cable User s Manual 12 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Product Highlights Basic Features Meets NEMA TS1 TS2 Environmental requirements such as temperature shock and vibration for t
102. h_a config IGMP mode Passive 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use ip igmp snooping command to enable IGMP Snooping This command is given in the Global Config mode IGMP Snooping is enabled at the switch level Use the no ip igmp snooping command to globally disable IGMP Snooping 3 Command Syntax no ip igmp snooping enable 4 Example The following example enables IGMP snooping on the switch switch_a config ip igmp snooping enable switch_a config IGMP version 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode vian1 1 means vlan 1 User s Manual 172 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch The switch_a config if prompt will show on the screen switch_a config interface vian1 1 switch_a config if 2 Usage Use ip igmp version command to set the current IGMP protocol version on an interface To return to the default version use the no ip igmp version command 3 Command Syntax ip igmp version VERSION no ip igmp version VERSION IGMP protocol version number 4 Example The following example sets the IGMP protocol version 3 on vian1 1 switch_a config interface vian1 1 switch_a config if ip igmp version 3
103. he bandwidth value is in bits Use the no parameter with this command to remove the bandwidth for each interface User s Manual 117 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 3 Command Syntax Bandwidth BANDWIDTH no bandwidth BANDWIDTH lt 1 10000000000 bits gt usable units k m g lt 1 999 gt k m for 1 to 999 kilo bits or mega bits 1g for 1 giga bits 4 Example The following example shows the use of bandwidth BANDWIDTH 10 mega bits to the interface fe1 port 1 switch_a config interface fe1 switch_a config if bandwidth 10m switch_a config if Duplex 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use duplex command to specify the duplex mode to be used for each interface Use the no duplex to disable this function 3 Command Syntax no duplex MODE MODE specifies the duplex mode auto full half 4 Example The following example shows the use of duplex MODE full to the interface fe1 port 1 switch_a config interface fe1 switch_a config if duplex full switch_a config if Flow control 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode User s Manual 118 SIGNAMAX CONNECTIVIT
104. he ID of the VLAN or VLANs that will be added to or removed from the Layer 2 interface A single VLAN VLAN range or VLAN list can be set For a VLAN range specify two VLAN numbers lowest then highest number in the range separated by a hyphen For a VLAN list specify the VLAN numbers separated by commas 4 Example The following example specifies to add the interface fe1 port 1 to VLANID 2 switch_a config interface fe1 switch_a config if switchport trunk allowed vlan add 2 switch_a config if User s Manual 150 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Port Based VLAN Switchport portbase add remove vlan 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use this command to set or remove the default VLAN for the interface 3 Command Syntax switchport portbase add remove vlan VLANID VLANID The ID of the VLAN will be added to or removed from the Layer 2 interface 4 Example The following example specifies to add the interface fe1 port 1 to VLANID 2 switch_a config interface fe1 switch_a config if switchport portbase add vlan 2 switch_a config if User s Manual 151 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE E
105. he switch It describes the types of management applications and the communication and management protocols that deliver data between your management device workstation or personal computer and the system It also contains information about port connection options This chapter covers the following topics Management Access Overview s Key Concepts e Key Guidelines for Implementation Web Management Access e Administration Console Access e SNMP Access Standards Protocols and Related Reading Management Access Overview The switch gives you the flexibility to access and manage the switch using any or all of the following methods The web browser interface and administration console CLI support are embedded in the switch software and are available for immediate use User s Manual 21 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Administration Console CLI The administration console is an internal character oriented Command Line Interface CLI for performing system administration such as displaying statistics or changing option settings Using this method you can view the administration console from a terminal personal computer Apple Macintosh or workstation connected to the switch s console port There are two ways to use this management method direct access or modem access The following sections describe these methods Direct Access Direct access to the admin
106. hentication drop down list to choose Enable or Disable to enable or disable periodic reauthentication 5 Reauthentication Period lt 1 4294967295 gt Click in the Reauthentication Period textbox and specify the seconds between reauthorization attempts The default time is 3600 seconds 6 Update Setting Click Update Setting button when you finished port authentication setting User s Manual 87 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Other Protocols amp Welcome to Switch Management Microsoft Internet Explorer DER File Edit View Favorites Tools Help ae Q sac Q x a A Search sie Favorites amp by amp E 3 Address http 192 168 1 10 cgi bin switch cgi v B co Links BE DA GE fanagement Switch O System Port ENED Switching GVRP Disable v HO Trunking Dynamic VLAN creation Disable ere Gi VLAN SE Qos Per port setting include LAG SNMP CS 802 1 GVRP GVRP applicant GVRP registration EE Other Protocols GVRP Disable Normal Disable IGMP Snooping NIP Disable v Normal Disable GVRP Global Setting Disable Normal Disable x Disable Normal Disable Disable Normal Disable Disable Normal Disable Disable Normal v Disable Disable Normal Disable Update Setting Internet GVRP GVRP Global Setting 1 GVRP Click GVRP drop down menu from GVRP
107. ig snmp server trap type enable linkUp switch_a config Authentication Failure Trap 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage User s Manual 159 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Use snmp server trap type enable authenticationFailure command to enable authentication failure trap for SNMP Use the no snmp server trap type enable authenticationFailure command to disable authentication failure trap for SNMP 3 Command Syntax no snmp server trap type enable authenticationFailure 4 Example The following example enables authentication failure trap for SNMP switch_a config snmp server trap type enable authenticationFailure switch_a config Topology Change Trap 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use snmp server trap type enable topologyChange command to enable topology change trap for SNMP Use the no snmp server trap type enable topologyChange command to disable topology change trap for SNMP 3 Command Syntax no snmp server trap type enable topologyChange 4 Example The following example enables topology change trap for SNMP switch_a config snmp server trap type enable to
108. ill show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use storm control dif enable command to enable destination lookup failure traffic Use no storm control dif command to disable destination lookup failure traffic 3 Command Syntax storm control dif enable no storm control dlf dif destination lookup failure 4 Example The following example shows setting storm control dif enable to the interface fe1 port 1 switch_a config interface fe1 switch_a config if storm control dif enable switch_a config if Static MAC Entry Static MAC Entry Forward 1 Command Mode Configure mode User s Manual 124 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to statically configure a bridge entry to forward matching frames 3 Command Syntax bridge GROUP address MAC forward IFNAME VLANID no bridge GROUP address MAC forward IFNAME VLANID GROUP lt 1 1 gt Bridge group ID used for bridging MAC the Media Access Control MAC address in the HHHH HHHH HHHH format IFNAME the interface on which the frame comes in VLANID The VID of the VLAN that will be enabled or disabled on the bridge lt 2 4094 gt 4 Example The following example configures a bridge GROUP 1 to forward matching f
109. ing the switch to your network Use appropriate cables that meet your speed and cabling requirements Cable Specifications Speed Connector Port Cable Max Speed Distance Half Full Duplex 10BaseT RJ 45 10 20 Mbps 2 pair UTP STP Cat 3 4 5 100BaseTX RJ 45 100 200 2 pair Mbps UTP STP Cat 5 1000BaseT RJ 45 2000 Mbps 4 pair 100 m UTP STP Cat 5 1000BaseSX Duplex LC 2000 Mbps MMF 220 m 62 5um 2 km 1000BaseSX Duplex LC 2000 Mbps MMF 550 m 50um 1000BaseLX Duplex LC 2000 Mbps SMF 10um 10 20 50 km 1000BaseBX Duplex LC 2000 Mbps SMF 10um 20 40 km User s Manual 19 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Cabling Step 1 First ensure the power of the switch and end devices are turned off lt Note gt Always ensure that the power is off before any installation Step 2 Prepare cable with corresponding connectors for each type of port in use Step 3 Consult Cable Specifications Table on previous page for cabling requirements based on connectors and speed Step 4 Connect one end of the cable to the switch and the other end to a desired device Step 5 Once the connections between two end devices are made successfully turn on the power and the switch is operational User s Manual 20 CONNECTIVITY SYSTEMS gt Hardened Managed PoE Ethernet Switch Switch Management This chapter explains the methods that you can use to configure management access to t
110. instance of a bridge 3 Command Syntax bridge GROUP instance INSTANCE_ID vlan VLAN_ID no bridge GROUP instance INSTANCE_ID vlan VLAN_ID GROUP lt 1 1 gt Specify the bridge group ID INSTANCE_ID lt 1 15 gt Specify the instance ID VLAN_ID lt 1 4094 gt Specify multiple VLAN IDs corresponding to the bridge instance 4 Example The following example associates multiple VLANs 10 and 20 to instance 1 of bridge GROUP 1 switch_a config bridge 1 protocol mstp switch_a config spanning tree mst configuration switch_a config mst bridge 1 instance 1 vlan 10 20 switch_a config mst Bridge Instance Priority 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode User s Manual 141 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to set the bridge priority for an MST instance to the value specified Use the no parameter with this command to restore the default value of the bridge priority The lower the priority of the bridge the better the chances are the bridge becoming a root bridge or a designated bridge for the LAN The priority values can be set only in increments of 4096 3 Command Syntax bridge GROUP instance INSTANCE_ID priority BRIDGE_PRIORITY no bridge GROUP instance INSTANCE_ID priority GROUP lt 1 1 gt Specify the bridge group ID
111. interface fe1 switch_a config if 2 Usage Use spanning tree link type command to set the link type of a port to enable or disable rapid transition User s Manual 137 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Use the no spanning tree link type command to set a port to its default state and to disable rapid transition 3 Command Syntax no spanning tree link type LINKTYPE LINKTYPE The link type to be assigned to the port point to point Enable rapid transition shared Disable rapid transition 4 Example The following example sets the link type LINKTYPE point to point of the interface fe1 port 1 switch_a config interface fe1 switch_a config if spanning tree link type point to point switch_a config if Autoedge 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use spanning tree autoedge command to assist in automatic identification of the edge port Use the no spanning tree autoedge command to disable this feature 3 Command Syntax no spanning tree autoedge 4 Example The following example enables the spanning tree autoedge of the interface fe1 port 1 switch_a config interface fe1 switch_a config if spanning tree autoedge swi
112. is 0 7 4 Example The following example shows mapping CoS values 0 and 1 to queue 1 on the switch switch_a config wrr queue cos map 1 0 1 switch_a config DSCP 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use mls gos map dscp queue command to map the DSCP values to a queue 3 Command Syntax mls qos map dscp queue DSCP_VALUE to QUEUE_ID DSCP_VALUE DSCP values Up to 8 values separated by spaces Range is 0 63 QUEUE_ID Queue ID Range is 0 3 4 Example The following example shows mapping DSCP values 0 to 3 to queue 1 on the switch switch_a config mls qos map dscp queue 0 1 2 3 to 1 switch_a config User s Manual 154 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch SNMP General Setting SNMP v1 v2c SNMP v3 SNMP General Setting SNMP Status 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use snmp server enable command to enable and no snmp server enable command to disable SNMP to the switch 3 Command Syntax no snmp server enable 4 Example The following example enables SNMP to the switch switch_a config snmp server enable switch_a config Description 1 C
113. isabled O wv TET RSTP Port Coefiguration CD Oter Protocols Port Prority Granmilarity 16 Admin Path Con Poin to Pois Link Edge Port 1m 12 200000 Enable Daabe L Update Seting remat RSTP Port Setting 1 STP Version Click STP Version drop down menu to choose RSTP from STP Version drop down list 2 Port Click Port drop down menu to choose Port 1 Port 8 from Port drop down list 3 Priority Granularity 16 Click in Priority text box and enter a value between 0 and 240 to set the priority for the port A higher priority will designate the port to forward packets first A lower number denotes a higher priority This entry must be divisible by 16 The default priority setting is 128 4 Admin Path Cost Click in Admin Path Cost text box and enter a value between 0 and 2000000 to set the Admin Path Cost for the port 0 auto Setting 0 for the Admin Path Cost will automatically set the speed for forwarding packets to the port for optimal efficiency Default port cost 100Mbps port 200000 Gigabit port 20000 5 Point to Point Link Click Point to Point Link drop down menu to Choose Enable or Disable from Point to Point Link drop down list to enable or disable Point to Point Link for the port 6 Edge Port Click Edge Port drop down menu to Choose Enable Disable or Auto from Edge Port drop down list to set Enable User
114. ished Radius Status Setting User s Manual 84 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer DER File Edit View Favorites Tools Help ay Q ack Q x a A JO Search sie Favorites amp Na bd i2 33 Address http 192 168 1 10 cgi bin switch cgi v Go Links Management Switch E O System Port Radius Server IP Switching Radius Server Port HC Trunking STP Ring van Timeout lt 1 1000 gt FH Qos Retransmit lt 1 100 gt SNMP EG 802 1x Radius Configuration Port Authentication Other Protocols Secret Key Done Internet Add Radius 1 Add Radius Click Add Radius button The Radius Server Setting window appears 2 Radius Server IP Click in the Radius Server IP textbox and specify the IP address of the remote radius server host 3 Radius Server Port Click in the Radius Server Port textbox and specify the UDP destination port for authentication requests The host is not used for authentication if set to 0 4 Secret Key Click in the Secret Key textbox and specify the authentication and encryption key for all radius communications between the Switch and radius server This key must match the encryption used on the radius daemon All leading spaces are ignored but spaces within and at the end of the key are used If spaces are used in the k
115. istration console is achieved by directly connecting a terminal or a PC equipped with a terminal emulation program such as HyperTerminal to the switch console port When using the management method configure the terminal emulation program to use the following parameters you can change these settings after login DEFAULT PARAMETERS e 115 200bps 8 data bits No parity 1 stop bit This management method is often preferred because you can remain connected and monitor the system during system reboots Also certain error messages are sent to the serial port regardless of the interface through which the associated action was initiated A Macintosh or PC attachment can use any terminal emulation program for connecting to User s Manual 22 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch the terminal serial port A workstation attachment under UNIX can use an emulator such as TIP Modem Access You can access the switch s administration console from a PC or Macintosh using an external modem attached to the console port The switch management program provides Console Port screen accessible from the Basic Management screen that lets you configure parameters for modem access When you have configured the external modem from the administration console the switch transmits characters that you have entered as output on the modem port The switch echoes characters that it receives as input on the mod
116. le name flash tgz from tftp server IP address 192 168 1 100 to switch switch_a install image 192 168 1 100 flash tgz switch_a Load config to TFTP server User s Manual 111 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 1 Command Mode Privileged Exec mode Logon to Privileged Exec Mode Enable Mode The switch_a prompt will show on the screen switch_a 2 Usage Use write config file command to backup configuration file to tftp server 3 Command Syntax write config file IP ADDRESS IP ADDRESS specifies the IP address of tftp server 4 Example The following example backups configuration file to tftp server IP address 192 168 1 20 switch_a write config file 192 168 1 20 switch_a Save Configuration 1 Command Mode Privileged Exec mode Logon to Privileged Exec Mode Enable Mode The switch_a prompt will show on the screen switch_a 2 Usage Use copy running config startup config command to write configurations to the file to be used at startup This is the same as the write memory command 3 Command Syntax copy running config startup config 4 Example The following example specifies writing configurations to the file to be used at startup to switch switch_a copy running config startup config switch_a Restore Default 1 Command Mode Privileged Exec mode Logon to Privileged Exec Mode Enable Mo
117. manual you should have an understanding of Ethernet networking concepts In this manual you will find Features on the Hardened Managed Ethernet Switch Illustrative LED functions Installation instructions Management Configuration SNMP IGMP Specifications User s Manual 9 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Table of Contents Quick Start Guide 1 PHYSICAL DESCRIPTION 1 The Port Status LEDs and Power Inputs 1 FUNCTIONAL DESCRIPTION 3 CONSOLE CONFIGURATION 4 WEB CONFIGURATION 6 Preface 9 Table of Contents 10 Product Overview 12 HARDENED MANAGED ETHERNET SWITCH 12 PACKAGE CONTENTS 12 PRODUCT HIGHLIGHTS 13 Basic Features 13 Management Support 13 FRONT PANEL DISPLAY 15 PHYSICAL PORTS 15 SWITCH MANAGEMENT 17 Web based browser interface 17 Administration console via RS 232 serial port CLI 17 External SNMP based network management application 17 Installation 18 SELECTING A SITE FOR THE SWITCH 18 CONNECTING TO POWER 18 DC Terminal Block Power Input 18 CONNECTING TO YOUR NETWORK 19 Cable Type amp Length 19 Cabling 20 Switch Management 21 MANAGEMENT ACCESS OVERVIEW 21 ADMINISTRATION CONSOLE CLI 22 Direct Access 22 Modem Access 23 WEB MANAGEMENT 23 SNMP BASED NETWORK MANAGEMENT 23 PROTOCOLS 24 MANAGEMENT ARCHITECTURE 24 Web Based Browser Management 25 SNMP amp RMON Management 26 User s Manual 10 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switc
118. minal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to specify the maximum allowed hops for BPDU in an MST region This parameter is used by all the instances of the MST Specifying the max hops for a BPDU prevents the messages from looping indefinetely in the network When a bridge receives a MST BPDU that has exceeded the allowed max hops it discards the BPDU 3 Command Syntax bridge GROUP max hops HOP_COUNT no bridge GROUP max hops User s Manual 140 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch GROUP lt 1 1 gt Specify the bridge group ID HOP_COUNT Maximum hops the BPDU will be valid for 4 Example The following example specifies the maximum allowed hops 25 for BPDU in bridge GROUP 1 switch_a config bridge 1 max hops 25 switch_a config MSTP Instance Setting Bridge Instance VLAN 1 Command Mode MST Configuration mode Logon to Configure Mode Configure Terminal Mode Then logon to MST Configuration mode The switch_a config mst prompt will show on the screen switch_a config spanning tree mst configuration switch_a config mst 2 Usage Use this command to simultaneously add multiple VLANs for the corresponding instance of a bridge This command can be used only after the VLANs are defined Use the no parameter with this command to simultaneously remove multiple VLANs for the corresponding
119. ne User s Manual 55 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch power priority of this port 5 Submit Click Submit button when you finished PoE Port Setting Flexible 802 3af High Power PoE Operation Compatible with the 802 3at Standard This Hardened Managed PoE amp High Power PoE Ethernet switch is compliant with the 802 3af High Power standard providing 30W of pure power to power demanding devices such as pan tilt zoom PTZ network cameras wireless access bridge routers and large screen network video phones et cetera This 802 3af High Power switch s PoE operation with 802 3at based PD is highly versatile and adaptable Normally when an 802 3at PD is connected to an 802 3af High Power compliant switch the switch will detect that the PD s power requirement is based on class 4 classification outlined in the IEEE802 3at standard and only attempt to provide 15 4W of power which is insufficient to power a 30W 802 3at PD This is due to the reason that the 30W of power in 802 3af High Power is classified as class 0 However this 802 3af High Power switch can support 30W 802 3at PD by setting the switch explicitly to provide a fixed rate of 30W power to 30W 802 3at PD 1 Power Limit by Classification Uncheck Power Limit by Classification to disable Port 1 Port 4 to provide power to 30W 802 3at PD according to classification of maximum power range used by PD 2 Fixed Power Limi
120. nfig if ip igmp query max response time 8 switch_a config if IGMP passive snooping Static mc router port 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode vian1 1 means vlan 1 The switch_a config if prompt will show on the screen switch_a config interface vian1 1 switch_a config if 2 Usage Use ip igmp snooping mrouter interface command to statically configure the specified VLAN constituent interface as a multicast router interface for IGMP Snooping in that VLAN Use the no ip igmp snooping mrouter interface command to remove the static configuration of the interface as a multicast router interface 3 Command Syntax no ip igmp snooping mrouter interface IFNAME IFNAME Specify the name of the interface 4 Example The following example shows interface fe1 port 1 statically configured to be a multicast router interface on vian1 1 switch_a config interface vlan1 1 switch_a config if ip igmp snooping mrouter interface fe1 switch_a config if User s Manual 175 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch IGMP passive snooping Report suppression 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode vian1 1 means vlan 1 The switch_a config if prompt will show on the screen switch_a config interface vlan1 1 switch_
121. ns see also undebug do To run exec commands in config mode enable Modify enable password parameters exit End current mode and down to previous mode help Description of the interactive help system hostname Set system s network name interface Select an interface to configure ip Internet Protocol IP lacp LACP commands line Configure a terminal line log Logging control mls Switch L2 no Negate a command or set its defaults priority queue Enable the egress expedite queue service Set up miscellaneous service set Set GHRP Registration to Fixed Registration show Show running system information snmp server Configure snap setting username Establish User Name Authentication vlan Configure VLAN parameters wrr queue WRR queue switch_alconfig _ Connected 0 24 15 VT100 115200 8 N l At the switch_a config prompt just type in the full or partial command string then typing a question mark to display the command keywords or parameters along with a short description switch_a config show User s Manual 105 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 115200 HyperTerminal File Edit View Call Transfer Help Oe s3 GS help Description of the interactive help system hostname Set system s network name interface Select an interface to configure ip Internet Protocol IP lacp LACP commands line Configure a terminal line log Logging control mls Switch L2
122. o Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use this command to specify the ingress egress rate to be used for each interface The bandwidth value is in bits Use the no parameter with this command to remove the ingress egress rate to be used for each interface 3 Command Syntax no rate control ingress egress VALUE VALUE lt 1 10000000000 bits gt usable units k m g lt 1 999 gt k m for 1 to 999 kilo bits or mega bits 1g for 1 giga bits 4 Example The following example shows the use of rate control ingress VALUE 10 mega bits to the interface fe1 port 1 switch_a config interface fe1 switch_a config if rate control ingress 10m switch_a config if RMON Siatistics 1 Command Mode Exec mode or Privileged Exec mode Logon to Exec Mode View Mode or Privileged Exec Mode Enable Mode The switch_a gt or switch_a prompt will show on the screen switch_a gt switch_a 2 Usage Use the show interface statistics command to display RMON statistics of interface 3 Command Syntax show interface statistics IFNAME IFNAME specifies the name of the interface for which RMON statistics is desired User s Manual 120 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 4 Example The
123. o choose instance ID from Instance ID drop down list MSTP Port Configuration 1 Port Click Port drop down menu to choose port from Port drop down list 2 Priority Granularity 16 Click in Priority text box to set the port priority for a bridge group The Multiple Spanning Tree Protocol uses port priority as a tiebreaker to determine which port should forward frames for a particular instance on a LAN or which port should be the root port for an instance A lower value implies a better priority In the case of the User s Manual 67 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch same priority the interface index will serve as the tiebreaker with the lower numbered interface being preferred over others The permitted range is 0 240 The priority values can only be set in increments of 16 3 Admin Path Cost Click in Admin Path Cost text box to set the cost of a path associated with an interface 4 Update Setting Click Update Setting button when you finished MSTP Port Setting DER amp File Edit View Favorites Tools Help Q sax Q x a 2s Search sie Favorites 5 Sd B7 s amp 3 Address http 192 168 1 10 cgi bin switch cgi Eco ilink K Management Switch a syne Ring state disable Update Setting gt Port HC Switching HO Trunking Set ring port Ring port 1 Ring port 2 FS STP Ring Ring port state DOWN DOWN Global Con
124. o enable the egress expedite queue Use the no priority queue out command to disable the egress expedite queue 3 Command Syntax no priority queue out 4 Example The following example enables the egress expedite queue on the switch switch_a config priority queue out switch_a config Weighted Round Robin 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use wrr queue bandwidth command to specify the bandwidth ratios of the transmit queues 3 Command Syntax wrr queue bandwidth WRR_WTS WRR_WTS Weighted Round Robin WRR weights for the 4 queues 4 values separated by spaces Range is 1 55 4 Example The following example specifies the bandwidth ratios of the transmit queues on the switch switch_a config wrr queue bandwidth 1 2 4 8 switch_a config User s Manual 153 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 802 1p Priority 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use wrr queue cos map command to specify CoS values for a queue 3 Command Syntax wrr queue cos map QUEUE_ID COS_ VALUE QUEUE_ID Queue ID Range is 0 3 COS_VALUE CoS values Up to 8 values separated by spaces Range
125. ommand Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use snmp server description command to specify and no snmp server description command to remove description for SNMP 3 Command Syntax snmp server description DESCRIPTION no snmp server description DESCRIPTION The description for SNMP 4 Example The following example specifies description description for SNMP switch_a config snmp server description description switch_a config User s Manual 155 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Location 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use snmp server location command to specify and no snmp server location command to remove location for SNMP 3 Command Syntax snmp server location LOCATION no snmp server location LOCATION The location for SNMP 4 Example The following example specifies location location for SNMP switch_a config snmp server location location switch_a config Contact 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use snmp server contact command to
126. onfig interface fe1 switch_a config if poe power priority high switch_a config if PoE Scheduling PoE Schedule 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use this command to enble PoE scheduling to this port 3 Command Syntax poe schedule enable 4 Example The following example enables PoE scheduling to the interface fe1 port 1 switch_a config interface fe1 switch_a config if poe schedule enable switch_a config if PoE Schedule 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen User s Manual 129 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch switch_a config interface fe1 switch_a config if 2 Usage Use this command to set PoE scheduling to this port 3 Command Syntax poe schedule time DAY HOUR DAY lt 0 6 gt specifies Sunday Saturday to Switch HOUR lt 0 23 gt specifies hours to Switch no poe schedule time 4 Example The following example sets PoE scheduling to the interface fe1 port 1 switch_a config interface fe1 switch_a config if poe schedule tim
127. p Click Link Up Trap drop down menu from Link Up Trap drop down list to choose Enable or Disable to enable or disable link up trap 9 Update Setting Click Update Setting button when you finished SNMP General Setting A Welcome to Switch Management Microsoft Internet Explorer MBR File Edit View Favorites Tools Help Q pack x a A p gt Search sie Favorites Az A s 33 Address http 192 168 1 10 cgi bin switch cgi_ v Go Links K Management Switch HG System SNMP V1 V2c Setting HO Port Get Community Name public SC Switching Set Community Name private Update Setting SNMP General Setting SNMP vi v2c SNMP v3 BC 802 1x C Other Protocols Done Internet A v1 v2c Get Community Name Click in the Get Community Name textbox and specify a get community name 2 Set Community Name Click in the Set Community Name textbox and specify a set community name 3 Update Setting Click Update Setting button when you finished SNMP V1 V2c Setting User s Manual 80 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch File Edit View Favorites Tools Help Welcome to Switch Management Microsoft Internet Explorer DER 7 Q pack x a ye Search She Favorites 2 a 3 Address a http 192 168 1 10 cgi bin switch cgi x Eco Links i Management Switch System SNMPv3 Setting Add User
128. peration 40 F to 185 F 40 C to 85 C 40 F to 185 F 40 C to 85 C 5 95 non condensing UL508 FCC Part 15 Class A EN61000 6 4 EN55022 EN61000 3 2 EN61000 3 3 EN61000 6 2 EN61000 4 2 EN61000 4 3 EN61000 4 4 EN61000 4 5 ESD Standard Radiated RFI Standards Burst Standards Surge Standards EN61000 4 6 Induced RFI Standards EN61000 4 8 Magnetic Field Standards IEC60068 2 6 Fc Vibration Resistance IEC60068 2 27 Ea Shock IEC60068 2 32 Ed Free Fall NEMA TS1 2 Environmental requirements for traffic control equipment User s Manual 181 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Appendix A DB9 DCE pin assignment Pin no Name RS232 Signal name 1 DCD Data Carrier detect 2 RxD Received data 3 TxD Transmit data 4 N C 5 GND Signal ground 6 DSR Data set Ready 7 N C 8 CTS Clear to send 9 N C User s Manual 182 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Appendix B Time Zone Country and City Lists Europe MEZ 1MESZ Europe Vienna Europe Berlin Europe Zurich MET 1METDST Africa Tunis CET MET Europe Tirane Europe Andorra Europe Brussels Europe Prague Europe Copenhagen Europe Paris Europe Gibraltar Europe Budapest Europe Rome Europe Vaduz Europe Luxembourg Europe Malta Europe Monaco Europe Amsterdam Europe Oslo Europe Warsaw Europe Bel
129. plements the Spanning Tree Protocol The dotidTp Group contains objects that describe the entity s transparent bridging status This group is applicable to transparent operation only and SRT bridges The dotidStatic Group contains objects that describe the entity s destination address filtering status This group is applicable to any type of bridge which performs destination address filtering User s Manual 28 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Web Based Browser Management The switch provides a web based browser interface for configuring and managing the switch This interface allows you to access the switch using a preferred web browser This chapter describes how to configure the switch using its web based browser interface Logging on to the switch Login Microsoft Internet Explorer File Edit View Favorites Tools Help Q pack x a A y Search she Favorites E Address http 192 168 1 10 password Internet SWITCH IP ADDRESS In your web browser specify the IP address of the switch Default IP address is 192 168 1 10 User s Manual 29 SIG NAMAX Hardened Managed PoE Ethernet Switch CONNECTIVITY SYSTEMS LOGIN Enter the factory default login ID root PASSWORD Enter the factory default password no password Or enter a user defined password if you followed the instructions later and changed the factory default password
130. pologyChange switch_a config SNMP v1 v2c Get Community Name 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use snmp server community get command to specify and no snmp server community get command to remove get community name for SNMP User s Manual 160 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 3 Command Syntax snmp server community get NAME no snmp server community get NAME The get community name for SNMP 4 Example The following example specifies get community name name for SNMP switch_a config snmp server community get name switch_a config Set Community Name 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use snmp server community set command to specify and no snmp server community set command to remove set community name for SNMP 3 Command Syntax snmp server community set NAME no snmp server community set NAME The set community name for SNMP 4 Example The following example specifies set community name name for SNMP switch_a config snmp server community set name switch_a config SNMP v3 SNMPv3 No Auth 1 Command Mode Configure mode Logon to Config
131. r 192 168 1 100 switch_a config Sync Time 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use ntp sync time command to synchronize time with NTP server 3 Command Syntax ntp sync time 4 Example The following example synchronizes time with NTP server switch_a config ntp sync time switch_a config Time Zone 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage User s Manual 178 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Use this command to to set time zone 3 Command Syntax clock timezone TIMEZONE TIMEZONE Specifies the time zone Please refer the Appendix B 4 Example The following example sets time zone Canada Yukon switch_a config clock timezone YST9YDT switch_a config Polling Interval 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to specify the polling interval 3 Command Syntax ntp polling interval MINUTE MINUTE lt 1 10080 gt The polling interval Enter a value in the range 1 to 10080 minutes 4 Example The followin
132. r classification enable switch_a config if Fixed Power Limit W 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use this command to specify the fixed power limit for this port to provide power to PD 3 Command Syntax poe fixed power limit LEVEL LEVEL lt 1 15 4 gt specifies the fixed power limit Watts for this port to provide power to PD 4 Example The following example sets new fixed power limit 15 Watts to the interface fe1 port 1 switch_a config interface fe1 switch_a config if poe fixed power limit 15 switch_a config if Power Priority 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen User s Manual 128 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch switch_a config interface fe1 switch_a config if 2 Usage Use this command to specify the power priority to this port 3 Command Syntax poe power priority PRIORITY PRIORITY specifies high medium low power priority for this port 4 Example The following example sets high power priority to the interface fe1 port 1 switch_a c
133. r date daylight saving for the Switch 2 Time Set Offset 1 1440 min Click in the Time Set Offset textbox and specify the offset time of daylight saving For example enter 60 for one hour offset 3 Name of Daylight Saving Timezone Click in the Name of Daylight Saving Timezone textbox and specify the name of daylight saving timezone This can be any given name in 14 character alpha numericals Enter the name of Daylight Saving time zone using the following example EDT East Daylight Saving Time Zone CDT Central Daylight Saving Time Zone MDT Mountain Daylight Saving Time Zone PDT Pacific Daylight Saving Time Zone ADT Alaska Daylight Saving Time Zone 4 Weekday Specify the daylight saving period e Month Click Month drop down menu from Month drop down list to choose from January to December e Week lt 1 5 gt Specifies starting ending week of daylight savings time e Day Click Day drop down menu from Day drop down list to choose from Sunday to Saturday e Hour lt 0 23 gt Specifies from 0 to 23 e Minute lt 0 59 gt Specifies from 0 to 59 5 Date Specify the daylight saving period e Month Click Month drop down menu from Month drop down list to choose from January to December e Day lt 1 31 gt Specifies from 1 to 31 e Hour lt 0 23 gt Specifies from 0 to 23 e Minute lt 0 59 gt Specifies from 0 to 59 6 Update Setting Click Update Setting button when you finished Da
134. raffic control equipment Meets EN61000 6 2 amp EN61000 6 4 EMC Generic Standard Immunity for industrial environment RS 232 console Telnet SNMP v1 amp v2c amp v3 RMON Web Browser and TFTP management Supports Command Line Interface in RS 232 console Supports 8192 MAC addresses Provides 2M bits memory buffer Supports IEEE802 3af Power over Ethernet PoE and IEEE802 3at PoE Power Sourcing Equipment PSE Supports IEEE802 3 802 3u 802 3ab 802 3z 802 3x Auto negotiation 1000Mbps full duplex 10 100Mbps full half duplex Auto MDI MDIX Provides up to two combo Gigabit ports SFP socket for Gigabit fiber optic expansion Supports digital diagnostics monitoring DDM digital optical monitoring DOM functions according to the industry standard SFF 8472 Store and forward mechanism Full wire speed forwarding rate Power Supply 47 57VDC Terminal Block power input Operating voltage and Max current consumption 0 37A 48VDC 0 32A 55VDC Power consumption 17 7W Max 40 C to 75 C 40 F to 167 F operating temperature range Tested for functional operation 40 C to 85 C 40 F to 185 F Hardened metal case Management Support VLAN Port based VLAN EEE802 1Q tagged VLAN User s Manual 13 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch TRUNKING Port Trunking PORT SECURITY Per port programmable MAC address locking Up to 24
135. rames MAC address 2222 2222 2222 to the interface fe1 port 1 in vlan VLANID 2 switch_a config bridge 1 address 2222 2222 2222 forward fe1 vlan 2 switch_a config Static MAC Entry Discard 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to statically configure a bridge entry to discard matching frames in a particular VLAN 3 Command Syntax bridge GROUP address MAC discard vlan VLANID no bridge GROUP address MAC discard vlan VLANID GROUP lt 1 1 gt Bridge group ID used for bridging MAC the Media Access Control MAC address in the HHHH HHHH HHHH format VLANID The VID of the VLAN on the bridge lt 1 4094 gt 4 Example The following example configures a bridge GROUP 1 to discard matching frames MAC address 2222 2222 2222 in vian VLANID 1 User s Manual 125 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch switch_a config bridge 1 address 2222 2222 2222 discard vlan 1 switch_a config Port Mirroring 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use this command to define a mirror source port
136. recently configured bridge IFNAME The name of the interface 4 Example The following example enables GVRP on the interface fe1 port 1 switch_a config set port gvrp enable fe1 switch_a config Per port setting GVRP applicant 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to set the GVRP applicant state to normal or active 3 Command Syntax set gvrp applicant state active normal IFNAME active Active state normal Normal state IFNAME Name of the interface User s Manual 170 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 4 Example The following example sets GVRP applicant state to active on the interface fe1 port 1 switch_a config set gvrp applicant state active fe1 switch_a config Per port setting GVRP registration 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to set GVRP registration to normal fixed and forbidden registration mode for a given port 3 Command Syntax set gvrp registration normal IF_NAME set gvrp registration fixed IF_NAME set gvrp registration forbidden IF_NAME normal Specify dynamic GVRP multicast registration and deregistration on
137. rica Montserrat America Puerto_Rico America St_Kitts America St_Lucia America St_Vincent America Tortola America St_Thomas America Aruba America La_Paz America Porto_Velho America Curacao America Caracas America Guyana Etc GMT 4 America Virgin SystemV AST4 UCT5 America Guayaquil America Eirunepe America Lima Etc GMT 5 UCT6 America Belize America El_ Salvador America Tegucigalpa Pacific Galapagos Etc GMT 6 UCT7 Etc GMT 7 User s Manual 186 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch UCT8 Etc GMT 8 UCT9 Pacific Gambier Etc GMT 9 SystemV YST9 UCT10 Pacific Rarotonga Pacific Tahiti Pacific Fakaofo Pacific Johnston Pacific Honolulu Etc GMT 10 HST US Hawaii SystemV HST10 UCT11 Pacific Niue Pacific Pago_Pago Pacific Apia Pacific Midway Etc GMT 11 Pacific Samoa US Samoa UCT 1 Africa Algiers Africa Luanda Africa Porto Novo Africa Douala Africa Bangui Africa Ndjamena Africa Kinshasa Africa Brazzaville Africa Malabo Africa Libreville Africa Windhoek Africa Niamey Africa Lagos Etc GMT 1 UCT 2 Africa Gaborone Africa Bujumbura Africa Lubumbashi Africa Tripoli Africa Blantyre Africa Maputo Africa Kigali Africa Lusaka Africa Harare Etc GMT 2 Libya UCT 3 Indian Comoro Africa Djibouti Africa Asmera Africa Addis_Ababa Africa Nairobi Indian Antananarivo Indi
138. rminal File Edit View Call Transfer Help Owe s3 op GC gurp GARP Vlan Registration Protocol hardware Hardware configuration history Display the session command history interface The layer interfaces ip Internet Protocol IP lacp LACP commands lacp counter LACP commands list Show command lists mac Mac address mirror Port Mirroring mls Switch L2 port port commands privilege Show current privilege level ratecontrol The layer interface spanning tree Display spanning tree information static channel group Static channel commands storm control The layer2 interface user priorilty Display the default user priority associated with the layer interface users Display information about terminal lines version Display version vlan Display VLAN information switch_a gt show Connected 0 05 59 VT100 115200 amp N 1 Login timed out The login session to Exec Mode or View Mode has timed out due to an extended period of inactivity 60 seconds to indicate authentication attempt timed out And the switch_a login prompt will show on the screen Logon back to Exec Mode View Mode User s Manual 97 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch At the switch_a login prompt just type in root and press lt Enter gt to logon back to Exec Mode or View Mode switch_a login root 115200 HyperTerminal File Edit View Call Transfer Help D a 090 switch_a login
139. s lt Enter gt to logon to Configure Mode or Configure Terminal Mode And the switch_a config prompt will show on the screen Set new IP address and subnet mask for Switch At the switch_a config prompt just type in interface vlan1 1 and press lt Enter gt to logon to vlan 1 vlan1 1 means vlan 1 And the switch_a config if prompt will show on the screen Command Syntax ip address A B C D M A B C D specifies IP address M specifies IP subnet mask M 8 255 0 0 0 16 255 255 0 0 or 24 255 255 255 0 For example At the switch_a config if prompt just type in ip address 192 168 1 10 24 and press lt Enter gt to set new IP address 192 168 1 10 and new IP subnet mask 255 255 255 0 for Switch User s Manual 5 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 115200 HyperTerminal File Ede View Call Transfer Help oe 08 e switch_a login root Switch version 1 49 1 61 22 09 15 40 59 switch _a gt enable switch_atconfigure terminal Enter configuration commands one per line End with CNTL Z switch_a config linterface vlan1 1 swilch_alconfig if Hip address 192 168 1 10 24 switch_a config if lt Connected 0 01 52 vT100 115200 8 N 1 Web Configuration Login the switch Specify the default IP address 192 168 1 10 of the switch in the web browser A login window will be shown as below User s Manual
140. s clock summer time TIMEZONE onehour as daylight saving offset 60 minutes from 4 April AM0 00 to 31 October AMO 00 switch_a config clock summer time onehour date 4 4 0 0 31 100060 switch_a config User s Manual 180 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Specifications Applicable Standards Switching Method Forwarding Rate 10BaseT 100BaseTX 1000BaseT SX LX BX Performance Cable 10BaseT 100BaseTX 1000BaseT 1000BaseSX LX BX LED Indicators Dimensions Net Weight Power Input Power Consumption Operating Temperature Storage Temperature Humidity Safety EMI EMS Environmental Test Compliance IEEE 802 3 10BaseT IEEE 802 3u 100BaseTX IEEE 802 3ab 1000BaseT IEEE 802 3z 1000BaseSX LX Store and Forward 10 20Mbps half full duplex 100 200Mbps half full duplex 2000Mbps full duplex 14 880pps for 10Mbps 148 810pps for 100Mbps 1 488 100pps for 1000Mbps 2 pair UTP STP Cat 3 4 5 Up to 328ft 100m 2 pair UTP STP Cat 5 Up to 328ft 100m 4 pair UTP STP Cat 5 Up to 328ft 100m MMF 50 or 62 5um SMF 9 or 10m Per unit Power Per port 10 100TX PoE Link ACT PoE 10 100TX Link ACT 10 100 1000TX 1000SX LX BX Link ACT SFP 7 87 W x 5 28 D x 1 97 H 200mm W x 134mm D x 50mm H 3 3lbs 1 5Kg Terminal Block 47 57VDC 17 7W Max 40 F to 167 F 40 C to 75 C Tested for functional o
141. sable or Enable from the Auto save drop down list to disable or enable Auto save for the switch 6 Auto save interval 5 65536 sec Click in Auto save interval text box and type a decimal number between 5 and 65536 7 Submit Click Submit button when you finished Auto save configuration User s Manual 38 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch A Welcome to Switch Management Microsoft Internet Explorer Ce File Edit View Favorites Tools Help a Q Back Q x a H p gt Search She Favorites ahd Se 3 Address http 192 168 1 10 cgi bin switch cgi v Eco links Wi Management Switch E Q System Firmware Version 1 91 0 09 28 11 12 17 25 System Information Filename System Name Password TETP server IP TP Address Route Table Save Configuration Firmware Uperade Internet Firmware Upgrade 1 Filename Click in Filename text box and type the name of the file that you intend to upgrade it to the switch 2 TFTP server IP Click in TFTP server IP text box and type the TFTP server IP address from where the file will be obtained 3 Upgrade Click Upgrade button to upgrade firmware to the switch Please follow the message on the screen during the firmware upgrade process Do not turn off the power or perform other functions during this period of time Reboot the switch after completing the upgrade process User s
142. se Disable or Enable from the Flow control drop down list to disable or enable Flow control for the port 4 Submit Click Submit button when you finished configurations User s Manual 46 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 1 sso ew wm 1297 Karn Gate Aine wens Lew Ais xo Hie Woes N Lew Wanag ex Alen NO hp Wanny Low Waag Low aien MA Nang Low Warning Lew Ales gt Ba Wes N Lew Wenas tp Wornng Vents 4261 sass 00w Ma wag Vad Wanay Ores Ts Bist Ales se gt Hit Waset Cured Tx Pora Ara 2 iia Wormer Cinna Bs Paen Alon Mag Nammi User s Manual 47 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 3 Welcome to Switch Management Microsoft Internet Explorer file Edt Yiew Fevorites Tools Help Ona O DAO Asun ferme BSB Bs http 192 168 1 10 cgi bin ewitch cgi SFP Port Alarm Setting Alarm Type Current Temperanae 39 089 C Temp High Alarm 128 128 c Temp Low Alarm 128_128 c Temp High Warming 12 125 DE Smitty SO Trung Temp Low Waring 128 128 c RO STP Rag EE VLAN VCC High Alarm 0 6 55 V ji w VCC Low Alarm 0 6 55 V O ML VCC High Warming 0 6 55 V HC Osher Protocols VCC Low Waring 0 6 55 V Cures Tx _bias 6 730 mA TX Bias High Alarm 0 131 mA N TX Bias Low Alarm 0 131 mA NO TX Bias High Waming 0 131 mA NO TX Bias Low Warning 0 131 mA NO Current Tx_pow 5 455 dbm TX Powes High
143. show on the screen switch_a config 2 Usage Use this command to choose the Spanning Tree protocol Rapid Spanning Tree protocol or Multiple Spanning Tree protocol on a bridge 3 Command Syntax bridge GROUP protocol PROTOCOL vlan bridge GROUP lt 1 1 gt Bridge group name used for bridging PROTOCOL ieee IEEE 802 1Q spanning tree protocol mstp IEEE 802 1s multiple spanning tree protocol rstp IEEE 802 1w rapid spanning tree protocol 4 Example The following example chooses the PROTOCOL rstp on bridge GROUP 1 switch_a config bridge 1 protocol rstp vian bridge switch_a config Multiple Spanning Tree Protocol 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to enable the Multiple Spanning Tree protocol on a bridge Use the no form of the command to disable the Multiple Spanning Tree protocol on a bridge 3 Command Syntax bridge GROUP multiple spanning tree enable User s Manual 132 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch no bridge GROUP multiple spanning tree enable BRIDGE FORWARD GROUP lt 1 1 gt Bridge group name used for bridging BRIDGE FORWARD Puts all ports of the specified bridge into the forwarding state 4 Example The following example enables or disables the multiple spanning tree on brid
144. specify and no snmp server contact command to remove contact for SNMP 3 Command Syntax snmp server contact CONTACT no snmp server contact CONTACT The contact for SNMP 4 Example The following example specifies contact contact for SNMP switch_a config snmp server contact contact switch_a config Trap Community Name User s Manual 156 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to specify trap community name for SNMP Use the no parameter with this command to remove trap community name for SNMP 3 Command Syntax snmp server trap community lt 1 5 gt NAME no snmp server trap community lt 1 5 gt lt 1 5 gt The trap community 1 5 NAME The trap community name for SNMP 4 Example The following example specifies trap community name 1 name for SNMP switch_a config snmp server trap community 1 name switch_a config Trap Host IP Address 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to specify trap host IP address for SNMP Use the no parameter with this command to remove trap host IP address for SNMP
145. switch_a config hostname switch switch config Password 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use enable password command to modify or create a password to be used when entering the Enable mode 3 Command Syntax enable password PASSWORD PASSWORD specifies the new password of the system 4 Example The following example sets the new password mypasswd to switch switch_a config enable password mypasswd User s Manual 108 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch switch_a config IP Address IP Address IP Subnet Mask 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode vian1 1 means vlan 1 The switch_a config if prompt will show on the screen switch_a config interface vian1 1 switch_a config if 2 Usage Use ip address command to set the IP address of an interface Use the no ip address command to remove the IP address from an interface 3 Command Syntax ip address IP ADDRESS no ip address IP ADDRESS no ip address IP ADDRESS A B C D M specifies the IP address and prefix length of an interface M specifies IP subnet mask 8 255 0 0 0 16 255 255 0 0 24 255 255 255 0 4 Example The following example sets th
146. switch_a config if Fast leave 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode vian1 1 means vlan 1 The switch_a config if prompt will show on the screen switch_a config interface vlan1 1 switch_a config if 2 Usage Use ip igmp snooping fast leave command to enable IGMP Snooping fast leave processing Fast leave processing is analogous to immediate leave processing the IGMP group membership is removed as soon as an IGMP leave group message is received without sending out a group specific query Use the no ip igmp snooping fast leave command to disable fast leave processing 3 Command Syntax no ip igmp snooping fast leave 4 Example The following example enables IGMP snooping fast leave on vian1 1 switch_a config interface vian1 1 switch_a config if ip igmp snooping fast leave switch_a config if User s Manual 173 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch IGMP querier Query interval 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode vian1 1 means vlan 1 The switch_a config if prompt will show on the screen switch_a config interface vian1 1 switch_a config if 2 Usage Use ip igmp query interval command to configure the frequency of sending IGMP host query messages To return to the
147. t 1812 switch_a config Secret Key 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to set the shared secret key between a Radius server and a Client 3 Command Syntax no radius server host IP ADDRESS key KEY IP ADDRESS A B C D specifies the IP address of the radius server host KEY specifies the secret key shared among the radius server and the 802 1x client 4 Example The following example specifies the IP address 192 168 1 100 of the remote radius server host and set the secret key ipi shared among the radius server and the 802 1x client switch_a config radius server host 192 168 1 100 key ipi switch_a config Timeout 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use this command to specify the number of seconds a Switch waits for a reply to a radius request before retransmitting the request 3 Command Syntax radius server timeout SEC no radius server timeout SEC lt 1 1000 gt The number of seconds for a Switch to wait for a server host to reply before timing out Enter a value in the range 1 to 1000 4 Example User s Manual 165 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switc
148. t W Click in Fixed Power Limit W text box and type a new fixed power limit OW for Port 1 Port 4 to provide power to 30W 802 3at PD 3 OK Click OK button to update your settings User s Manual 56 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch a Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help Q tack x a CA JO Search sie Favorites Q4 http 192 168 1 10 cgi bin switch cgi Management Switch PoE System Setting Port Main Supply Voltage 46 00 V B E Switching System Temperature 43 04 C Bridging Power Allocation 0 00 W System Power Budget 140 98 wW PoE Port Setting Power Limit Fixed Port Enable Mode by Power give Classification Limit W Priority Power Enable 000 High Searching N A H Other Protocols Enable High Searching N A Enable High Searching N A Enable l High Searching N A Internet User s Manual 57 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 3 Welcome to Switch Management Microsoft Internet Explorer Pie Edit Yew Fovorites Jools Help Qw O NAA Ason Irro O E EE http 192 168 1 10 cgh bin switch cgi PoE Per Port Scheduling Port 1 Status Not Scheduled Time Sun Mon 00 00 01 00 02 00 0300 0400 0500 06 00 07 00 0800 0900 1000 1100 12 00 13 00 1400 1500 160
149. t cable to the RS 232 serial port of the device and the RS 232 serial port of the terminal or computer running the terminal emulation application Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a terminal emulation program such as HyperTerminal to the switch console port Configuration settings of the terminal emulation program Baud rate 115 200bps Data bits 8 Parity none Stop bit 1 Flow control none Press the Enter key The Command Line Interface CLI screen should appear as below Logon to Exec Mode View Mode At the switch_a login prompt just type in root and press lt Enter gt to logon to Exec Mode or View Mode And the switch_a gt prompt will show on the screen User s Manual 4 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 115200 HyperTerminal Elle Edit View Call Transfer Help Ow 08 e switch_a login root Switch version 1 43 1 01 22 09 15 40 59 switch_a gt enable switch_ali Connected 0 03 28 vT100 115200 8 N 1 Logon to Privileged Exec Mode Enable Mode At the switch_a gt prompt just type in enable and press lt Enter gt to logon to Privileged Exec Mode or Enable Mode And the switch_a prompt will show on the screen Logon to Configure Mode Configure Terminal Mode At the switch_a prompt just type in configure terminal and pres
150. t mode and down to previous mode help Description of the interactive help system logout Exit from the FXEC no Negate a command or set its defaults quit Exit current mode and down to previous mode restore lo restore the default setting show Show running system information terminal Set terminal line parameters switch a gt Connected 0 03 49 T1003 115200 8 N 1 At the switch_a gt prompt just type in the full or partial command string then typing a question mark to display the command keywords or parameters along with a short description switch_a gt show User s Manual 96 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 115200 HyperTerminal File Edit View Call Transfer Help Oe s3 op Gg swilch_a gt show 7 all if all if brand Brand ID bridge bridge protocol cli Show CLI tree of current mode debugging Debugging functions see also undebug etherchannel LACP channel commands flowcontrol IFEF 802 3x Flow Control garp Generic Attribute Registration Protocol gurp GARP Vlan Registration Protocol hardware Hardware configuration history Display the session command history interface The layer interfaces ip Internet Protocol IP lacp LACP commands lacp counter LACP commands list Show command lists mac Mac address mirror Port Mirroring mls Switch L2 port port commands privilege Show current privilege level ore Connected 0 05 08 VT100 115200 8 N 1 115200 HyperTe
151. tch_a config if Edgeport 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode User s Manual 138 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use spanning tree edgeport command to set a port as an edge port and to enable rapid transitions Use the no spanning tree edgeport command to set a port to its default state not an edge port and to disable rapid transitions 3 Command Syntax no spanning tree edgeport 4 Example The following example enables the spanning tree edgeport of the interface fe1 port 1 switch_a config interface fe1 switch_a config if spanning tree edgeport switch_a config if MSTP Properties Region Name 1 Command Mode MST Configuration mode Logon to Configure Mode Configure Terminal Mode Then logon to MST Configuration mode The switch_a config mst prompt will show on the screen switch_a config spanning tree mst configuration switch_a config mst 2 Usage Use this command to create an MST region and specify a name to it MST bridges of a region form different spanning trees for different VLANs By default each MST bridge starts with the region name as its bridge address This means each MST bridg
152. tem Port5 Port Status Port 1 Statistics Rate Control RMON Statistics Per Port Vian Activities Drop Events Broadcast Packets Received Multicast Packets Received Undersize Packets Received Oversize Packets Received fragments_pkts 64 byte Packets Received 65 to 127 byte Packets Received 128 to 255 byte Packets Received H O Other Protocols 256 to 511 byte Packets Received 512 to 1023 byte Packets Receive 1 0 to 1 5 kbyte Packets Received Jabber Packets Bytes Received Packets Received Collisions CRC Alignment Errors Received TX No Errors RX No Errors RMON Statistics 35 0 0 2989689 21023 Internet Click Port 1 Port 8 to view corresponding RMON Statistics User s Manual 50 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 3 Welcome to Switch Management Microsoft Internet Explorer Ele Edt View Favorites Tools Help Qw O DAO Psu symm O A Las E herp 192 168 1 10 cgi bin switch cgi a W Loe oe Total VLAN Count 1 Total MAC Address Count 1 VLAN Membership MAC Address VLANI 0010 defc 3102 Per Port Vlan Activities Click Port 1 Port 8 to view corresponding vlan activities User s Manual 51 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help Q pack Q x a A gt Search sie Favorites O Address
153. the port fixed Specify the multicast groups currently registered on the switch are applied to the port but any subsequent registrations or deregistrations do not affect the port Any registered multicast groups on the port are not deregistered based on the GARP timers forbidden Specify that all GVRP multicasts are deregistered and prevent any further GVRP multicast registration on the port IF_NAME The name of the interface 4 Example The following example sets GVRP registration to fixed registration mode on the interface fe1 port 1 switch_a config set gvrp registration fixed fe1 switch_a config IGMP Snooping IGMP mode Querier 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen User s Manual 171 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch switch_a config 2 Usage Use ip igmp snooping querier command to enable IGMP querier operation on a subnet VLAN when no multicast routing protocol is configured in the subnet VLAN When enabled the IGMP Snooping querier sends out periodic IGMP queries for all interfaces on that VLAN Use the no ip igmp snooping querier command to disable IGMP querier configuration 3 Command Syntax no ip igmp snooping querier 4 Example The following example enables IGMP snooping querier switch_a config ip igmp snooping querier switc
154. thernet Switch Global Configuration 802 1p Priority DSCP Global Configuration QoS 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use mls qos enable command to globally enable QoS Use the no mls qos command to globally disable QoS 3 Command Syntax mls qos enable no mls qos 4 Example The following example globally enables QoS on the switch switch_a config mls qos enable switch_a config Trust 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use mls qos trust command to turn on QoS trust CoS or DSCP Use the no mls qos trust command to turn off QoS trust CoS or DSCP 3 Command Syntax no mls qos trust cos dscp cos Class of Service dscp Differentiated Service Code Point 4 Example The following example turns on QoS trust CoS on the switch switch_a config mls qos trust cos switch_a config User s Manual 152 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Strict Priority 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use priority queue out command t
155. to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use poe enable command to enable this port to discover Powered Device PD connected to this port Use the no poe enable to disable this function 3 Command Syntax no poe enable 4 Example The following example shows the use of poe enable to the interface fe1 port 1 switch_a config interface fe1 switch_a config if poe enable switch_a config if Power Limit by Classification 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use poe power classification enable command to enable this port to provide power to PD according to classification of maximum power range User s Manual 127 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch used by PD Use the no poe power classification enable to disable this function 3 Command Syntax no poe power classification enable 4 Example The following example shows the use of poe power classification enable to the interface fe1 port 1 switch_a config interface fe1 switch_a config if poe powe
156. try Discard settings User s Manual 53 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch i Welcome to Switch Management Microsoft Internet Explorer ek C7 File Edit View Favorites Tools Help Q sack Q x a JO Search she Favorites far 3 Address http 192 168 1 10 cgi bin switch cai v E co links Q Bridging Static MAC Entry Port Maroc PoE PoE Scheduling Internet Port Mirroring 1 Mirror From Choose Mirror From port from Port 1 Port 8 2 Mirror To Click Mirror To drop down menu to Choose Mirror To port Port 1 Port 8 from Mirror To drop down list 3 Mirror Mode Click Mirror Mode drop down menu to Choose Tx Rx Tx or Rx from Mirror Mode drop down list 4 Submit Click Submit button when you finished Port Mirroring settings User s Manual 54 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch a Welcome to Switch Management Microsoft Internet Explorer File Edit View Favorites Tools Help Q tack Q x a A p gt Search sie Favorites 2 Address http 192 168 1 10 cgi bin switch cgi Management Switch PoE System Setting Main Supply Voltage 47 00 V System Temperature 43 69 C Power Allocation 0 00 W System Power Budget 140 98 w PoE Port Setting Power Limit Fixed Port Enable Mode by Power
157. tton when you finished IGMP mode settings 3 VLAN ID Click VLAN ID drop down menu from VLAN ID drop down list to choose the VLAN under configuration for the switch 4 IGMP version Click IGMP version drop down menu from IGMP version drop down list to choose 1 2 or 3 for the switch 5 Fast leave Click fast leave drop down menu from fast leave drop down list to choose Enable or Disable for the switch Enable this function will allow members of a multicast group to leave the group immediately when an IGMP Leave Report Packet is received by the Switch IGMP querier 1 Query interval Click in the query interval textbox and specify a new number from 1 18000 The query interval field is used to set the time in seconds between transmitting IGMP queries Entries between 1 and User s Manual 90 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 18000 seconds are allowed Default 125 Max response time Click in the max response time textbox and specify a new number from 1 240 This determines the maximum amount of time in seconds allowed before sending an IGMP response report The max response time field allows an entry between 1 and 240 seconds Default 10 IGMP passive snooping 1 Report suppression Click report suppression drop down menu from report suppression drop down list to choose Enable or
158. ttp 192 168 1 10 cgi bin switch cgi v Go i Lines Ni Management Switch MSTP Properties Region Name default Revision Level 0 Max Hops 20 Digest 0xAC36177F50283CD4B83821D8AB26DE62 RSTP Port Setting CIST Root ID 800000e0b3212829 MSTP Properties CIST Reg Root ID 800000e0b3212829 MSTP Instance Setting CIST Bridge ID 800000e0b3212829 MSTP Port Setting Update Setting Recover Ring tm Capability Internet ime Properties STP Version Click STP Version drop down menu to choose MSTP from STP Version drop down list 2 Region Name Click in Region Name text box to create an MST region and specify a name to it MST bridges of a region form different spanning trees for different VLANs By default each MST bridge starts with the region name as its bridge address This means each MST bridge is a region by itself unless specifically added to one 3 Revision Level Click in Revision Level text box to specify the number for configuration information The default value of revision number is 0 4 Max Hops Click in Max Hops text box to specify the maximum allowed hops for BPDU in an MST region This parameter is used by all the instances of the MST Specifying the max hops for a BPDU prevents the messages from looping indefinetely in the network When a bridge receives a MST BPDU that has exceeded the allowed max hops it discards the BPDU 5 Update Setting Click Update Setting
159. up ID used for bridging 4 Example The following example globally enables GVRP to bridge GROUP 1 switch_a config set gvrp enable bridge 1 switch_a config Dynamic VLAN creation 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use set gvrp dynamic vian creation enable bridge command to enable and set gvrp dynamic vian creation disable bridge command to disable dynamic VLAN creation for a specific bridge instance 3 Command Syntax set gvrp dynamic vlan creation enable bridge GROUP set gvrp dynamic vlan creation disable bridge GROUP GROUP Bridge group ID used for bridging User s Manual 169 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch 4 Example The following example enables dynamic VLAN creation for bridge GROUP 1 switch_a config set gvrp dynamic vlan creation enable bridge 1 switch_a config Per port setting GVRP 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Use set port gvrp enable command to enable and set port gvrp disable command to disable GVRP on a port or all ports in a bridge 3 Command Syntax set port gvrp enable all IFNAME set port gvrp disable all IFNAME all All ports added to
160. ure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Add a user using snmp v3 with read only or read write access mode and without authentication Use the no form of the command to delete this user 3 Command Syntax User s Manual 161 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch no snmp server v3 user USERNAME ro rw noauth USERNAME Specify a user name ro read only access mode rw read write access mode 4 Example The following example adds a user myuser using snmp v3 with read only access mode and without authentication switch_a config snmp server v3 user myuser ro noauth switch_a config SNMPv3 Auth MD5 SNMPv3 Auth SHA 1 Command Mode Configure mode Logon to Configure Mode Configure Terminal Mode The switch_a config prompt will show on the screen switch_a config 2 Usage Add a user using snmp v3 with read only or read write access mode and with MD5 or SHA authentication Use the no form of the command to delete this user 3 Command Syntax no snmp server v3 user USERNAME ro rw auth md5 sha AUTH_PASSWORD USERNAME Specify a user name ro read only access mode rw read write access mode md5 authentication method sha authentication method AUTH_PASSWORD authentication password 4 Example The following example adds a user myuser using snmp v3 with r
161. w on the screen switch_a config interface fe1 switch_a config if 2 Usage Use switchport mode access command to set the switching characteristics of the Layer 2 interface to access mode and classify untagged frames only Use the no switchport access command to reset the mode of the Layer 2 interface to access default 3 Command Syntax switchport mode access no switchport access 4 Example The following example sets the switchport mode access of the interface fe1 port 1 switch_a config interface fe1 switch_a config if switchport mode access switch_a config if Switchport mode hybrid 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode User s Manual 147 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use switchport mode hybrid command to set the switching characteristics of the Layer 2 interface as hybrid and classify both tagged and untagged frames Use the no switchport hybrid command to reset the mode of the Layer 2 interface to access default 3 Command Syntax switchport mode hybrid switchport mode hybrid acceptable frame type all vlan tagged no switchport hybrid all Set all frames can be received vlan tagged Set vlan tagged fr
162. wing example specifies to enable reauthetication on the interface fe1 ort 1 switch_a config interface fe1 switch_a config if dot1x reauthentication switch_a config if Port Control 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 switch_a config if 2 Usage Use this command to force a port state Use no dot1x port control command to remove a port from the 802 1x management 3 Command Syntax dot1x port control auto force authorized force unauthorized no dot1x port control auto Specify to enable authentication on port force authorized Specify to force a port to always be in an authorized state force unauthorized Specify to force a port to always be in an unauthorized state 4 Example The following example specifies to enable authetication on the interface fe port 1 switch_a config interface fe1 switch_a config if dot1x port control auto switch_a config if Periodic Reauthentication Reauthentication Period 1 Command Mode Interface mode Logon to Configure Mode Configure Terminal Mode Then logon to Interface mode fe1 means port 1 The switch_a config if prompt will show on the screen switch_a config interface fe1 User s Manual 167 SIGNAMAX CONNECT
163. witch 3 Welcome to Switch Management Microsoft Internet Explorer Ele gdt yew Favorites Jools Help Qu O NAO Asan Py roms B3 A http 192 168 1 10 cg bin switch cgi Syotem Inferraatien Load config from TFTP server TFTP Server FILE Load Spalem Name Paars Backup config to TFTP server TFTP Server FILE Backup Save Cor guraton Route Table Restore Defaut L Auto save configuration Por Auto save deable E Switching Awto save interval 63335 sec oS Ts Subme SO STP Res a1 VLAN 2 os 26 se Se pots E Other Protocols Done Save Configuration 1 Load config from TFTP server Click in TFTP Server text box and type the TFTP server IP address from where the file will be obtained Click in FILE text box and type the name of the file that will be obtained Click Load button to load the file from the TFTP server 2 Backup config to TFTP server Click in TFTP Server text box and type the TFTP server IP address to where the file will be backupped Click in FILE text box and type the name of the file that will be backupped Click Backup button to backup the file to the TFTP server 3 Save Configuration Click Save Configuration button to save your configuration settings 4 Restore Default Click Restore Default button to restore the default settings of the switch 5 Auto save Click Auto save drop down menu to choose Di
164. ylight Saving Setting lt Note gt The Week Hour Minute and Day fields would not accept the alphabetic characters Like Jan Feb sun mon They only accept the two digit numbers 0 throught 9 User s Manual 93 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Command Line Console Management The switch provides a command line console interface for configuration purposes The switch can be configured either locally through its RS 232 port or remotely via a Telnet session For the later you must specify an IP address for the switch first This chapter describes how to configure the switch using its console by Commend Line Administration Console Connect the DB9 straight cable to the RS 232 serial port of the device to the RS 232 serial port of the terminal or computer running the terminal emulation application Direct access to the administration console is achieved by directly connecting a terminal or a PC equipped with a terminal emulation program such as HyperTerminal to the switch console port When using the management method configure the terminal emulation program to use the following parameters you can change these settings after login Default parameters 115 200bps 8 data bits No parity 1 stop bit User s Manual 94 SIGNAMAX CONNECTIVITY SYSTEMS Hardened Managed PoE Ethernet Switch Exec Mode View Mode 115200 HyperTerminal File Edit

Download Pdf Manuals

Related Search

Related Contents

Inves IPlayer50 Manual  ダウンロード      Kaye LTR -25/140 and LTR  Black Box KV2008A User's Manual    LG ESA-FAN50 hardware cooling accessory  

Copyright © All rights reserved. Failed to retrieve file