GSM-LINE ADAPTER PRO 5 GSM 900 / 1800
Contents
1. Transmission frequency GSM 900 MHz 1800 MHz 850MHz 1900MHz Dimensions 127x86x27 mm Net weight 70g Gross weight packed 400 g e Outputs OUT1 OUT2 OUT4 open collector outputs output current max 100mA allowed smallest load 150 Ohm it is necessary to use protecting diodes in case of using relays e g 1N4004 It is forbidden to connect it on supply voltage without loading Min 150 Ohm e g relay Error output Generated telephone line specification Line voltage 48 V Line current 25 Line impedance 600 Ohm Ringing voltage 72 V 25 Hz Dial tone 400 Hz Contents of the package GSM LINE ADAPTER PRO 5 Antenna adapter cable MMCX FME GSM 900 MHz 1800 MHz antenna 4 pieces of fixing supports User s Manual Warranty Summary table of parameters SMSFW1 Phone numbers necessary for forwarding the incoming SMS messages SMSFW2 PREFIX Prefix number necessary to access the external PSTN line USER1 Phone numbers that get SMS messages from the module in case of observing USER2 given incident codes ADDFIX Prefix number that should be added to telephone numbers called in GSM mode AUTO Phone number for autodial function 122. over to GSM transmission i e irrespective of the existence of an analogue phone line the adapter initiates the call through the GSM network This ensures the call transmission in case there is some fault in the telephone exchange or sub exchange i e if the wired phone line seemingly works but the alarm system cannot reach the monitoring station through the wired PSTN network Most alarm systems can be programmed to give an output PGM signal after a certain number of unsuccessful attempts If this signal arrives to the IN4 input of the adapter i e the wired line cannot be used the unit will initiate the next call through the GSM network If there is no wired telephone line connected to the adapter additional care must be taken to connect the IN4 input as follows If it is necessary to manage incoming GSM calls connect the IN4 input to the alarm system so that it will short circuit the input at the time of starting a call This is important to prevent an eventual incoming call from disturbing alarm reporting Receiving calls through the GSM network GSM LINE ADAPTER PRO 5 is able to manage the calls coming through the GSM network i e it can receive the incoming GSM calls by means of a simple analogue telephone set in places where there is no wired phone line extension This function works only if there is no wired telephone line connected to the module and the IN4 DIRECT GSM input is not short circuited This input of the module prevents t
3. would like to receive the incoming SMS messages in the fields SMSFW1 and SMSFW2 Note When the module successfully forwarded the incoming SMS message the message will be deleted from the SIM card to make space for further incoming messages Sending SMS Messages In Case of Alarms or Other Events The adapter continuously watches the calls initiated through the GSM network and notices the reports of CONTACT ID or ADEMCO Express formats If it observes any of the given event codes maximum 10 it will send an SMS message to one or two telephone numbers with a text that can be set by the user This function needs the setting of the following parameters Enter the phone numbers that you would like to send the SMS message to in the F USER1 USER2 fields Enter the event codes that should be responded by the unit the Event Code fields the texts belonging to them as SMS messages in the SMS text fields In case of CONTACT ID format the SMS message must start with a 4 digit incident code then comes a character and then you can enter the required message e g 1130 Burglary The first digit 1 means new event or opening or 3130 Restore after burglary The first digit 3 means restore event or closing You can use the joker character in the incident code then the adapter accepts any digit in the place of the joker character e g 313 Alarm In this case the module will send a message when it obse
4. GSM LINE ADAPTER PRO 5 GSM 900 1800 MHz 850MHz 1900MHz USER MANUAL gt Functions of the Unit The purpose of the GSM LINE ADAPTER PRO 3 is to interface to GSM network an alarm system that can inform the security monitoring station through wired telephone line There are two main application areas of the unit e This adapter makes it possible to install alarm systems in places where there is no wired PSTN line but it can be necessary to alarm the security monitoring station e By means of the GSM transmission the adapter improves the reliability of alarm reporting in cases when the wired alarm transmission does not work or fails e g when the phone lines are tampered or the telephone service is suspended due to technical reasons The adapter has some additional functions e The unit continuously watches if a CONTACT ID or ADEMCO Express report is directed towards the security monitoring station through the wired or GSM network and if either of the preset report codes is noticed it sends an appropriate SMS message with definable text to one or two telephone numbers Using this function the owner can get instant SMS messages not only of alarms but also of every event of closing opening e The module can convert CONTACT ID signals into SMS messages without being connected to the monitoring station To do this enter 123456789 instead of the telephone number of the monitoring station In th
5. SMS messages in case of some events To do this enter 123456789 instead of the telephone number of the monitoring station into the alarm control panel In case of alarm the alarm control panel will dial this number In this case the adapter module does not initiate a real phone call but simulates the operation of the monitoring station gives out handshake signals and acknowledges CONTACT ID and ADEMCO Express signals It is possible to send SMS messages about the received signals For this the SMS messages to be sent have to be preset as it is described in the previous section Automatic dial This function can be used in certain specific tasks e g emergency calls Enter the telephone number that you wish to be dialed automatically in the AUTO field The module will dial the number initiating a call through GSM network when the receiver of the connected phone device is picked up See picture at setting prefix numbers section Preparation of the Alarm System Before installing the adapter check the following settings on the alarms system e The report format must be set to CONTACT ID or ADEMCO Express e The phone numbers of the monitoring station must be entered together with district numbers so that they can be called from the SIM card through the GSM network e Dialing should be set to TONE mode Testing the GSM Signal Strength After the pushbutton on the adapter has been pressed shortly the number of blinks of t
6. an be fed back to the alarm system or used for initiating local alarming e PSTN MODE and GSM MODE The slow alternate blinking of these two LEDs indicate that there are no settings loaded or the loading process failed Instructions on Installation Before installing check the future environment of the adapter e Test the GSM signal strength with your mobile phone It may happen that the signal is not sufficient in the selected place In this case you can change the planned installation place before you mount the adapter If there are signal strength problems on the site of installation find a suitable place for the adapter or use a higher gain antenna e Do mount the unit in places where it is influenced by strong radiofrequency disturbances e g near electric motors etc e Do not mount the unit in wet or humid places Mounting Plastic fixing clips are supplied with the unit If it is possible put the GSM adapter into the same metal case as the alarm control panel If there is not enough room in the case of the alarm control panel install the adapter into another metal case Fix the antenna on top of the case Mounting the alarm control panel and the adapter should be started only after the antenna is fixed Screw the bigger connector of the antenna adapter cable into the antenna connector then carefully flip the other end of the cable into the mini connection of the telephone module IMPORTANT NOTE Make sure that you d
7. computer All necessary parameters for the operation of the module can be done by means of a PC Download 5_ from www tell hu website For programming it is necessary to have a 9 pole serial connecting cable serial mouse expanding cable Connect the module to the PC with the serial cable Start the program and choose the serial port where the module is connected With this program not only settings but the operation of the module can be traced as well The settings take effect only after being downloaded in the module by pressing the Write parameters to module button Further notes e The adapter accepts both Tone DTMF and Pulse dials e The adapter does not know in advance the length of the number to be dialed therefore do not wait too long before entering the next digit because if you do so the module might suppose that dialing has already finished The adapter expects at least 7 digits and does not start dialing until they are entered It starts calling a number of 7 and 10 digits after a 5 second pause In case of 11 or more digits the adapter starts dialing after a 2 second pause If an alarm system is connected the above mentioned does not mean a problem because of the quick automatic dialing this problem has to be considered only in case of manual dialing e Telephone numbers shorter than 7 digits can be dialed by entering after the number Enabling and disabling telephone number disp
8. given the adapter so that it shall omit this number from the called number in case of initiating GSM call To do this enter the prefix that is necessary to access the external main line in the Dial prefix number used for outside line PREFIX field e g 9 5 Settings x Phone numbers sms settings Call Filter Output Control Primary User RUSER1 Secondary User 1 SMS forward nr HSMSFW1 2 SMS forward nr HSMSPW2 Automatic dial nr HAUTO Dial prefix number used for outside line Prefix to add before phone numbers called in GSM mode HADDFIX Cancel changes As it be seen the picture there is an ADDFIX parameter This is another prefix number which the module inserts in front of the dialed number in all those cases when the telephone call is performed through GSM network GSM mode For example if the alarm system calls the wired telephone number without the area code with this parameter the area code can be added in case of calls through GSM network In fact this function got vital importance because of the characteristics of some foreign wired telephone line networks Forwarding Incoming SMS Messages It is possible to send the messages received by the SIM card to one or two other phone sets This makes safe the use of cheap non subscription cards for security purposes To do this enter the one or two phone numbers that you
9. he GSM MODE LED on the adapter indicates the actual GSM signal strength on a 5 point scale Controlling outputs OUT1 and OUT2 open collector outputs can be activated and deactivated remotely through a telephone call For this set the parameters below in PRO5_programmer program Prod Settings Phone numbers SMS settings Call Fiter Output Control Bell 103 Enable Output Control from the following phone numbers 1 Enabled phone number 2 Enabled phone number 3 Enabled phone number 4 Enabled phone number Do not use any additonal prefix number just area code and phone number 1 Controllable Output Timing 0 254 sec 255 bistable 255 2 Controllable Output Timing 0 254 sec 255 bistable 255 3 Output GSM error signal 4 Output Wired phone line error signal Commands during the call 1 2 0UT2 0N 4 OFF 5 OUT2 OFF Cancel changes Remote control will be available from the phone numbers set here If there is an incoming call from any of the phone numbers entered here the module does not forward the call to the security panel or the telephone set but automatically receives the call A beep in the telephone indicates ready to use condition and the two outputs can be controlled through the phone by pushing the following buttons 1 turn on OUT1 2 turn on OUT2 4 turn off OUT1 5 turn off OUT2 The outputs can be set to deactivate automatically afte
10. he adapter it is possible to switch over to direct GSM transmission even if a functioning wired phone line is connected to the adapter Preparation of the SIM Card The SIM card necessary for the operation of the unit can be bought from any GSM service provider The adapter is independent of the actual GSM network For preparation and programming purposes insert the SIM card into a mobile phone and perform the following settings Before starting to set up the adapter go through the following steps using the mobile phone e Make sure that the number of the SMS message centre is correctly set on the SIM card e Disable the PIN code request on the SIM card so that it shall not prompt for a PIN code on turning the unit on e Delete the unnecessary SMS messages from the card Setting the Parameters of the Adapter For the basic operation of the unit it is not necessary to set any parameter on the SIM card However in order to reach the additional functions of the adapter as detailed in the following sections it is required to set certain parameters e g the owner s phone number the number to be dialed to access the external PSTN line the texts of SMS messages etc These parameters can be entered by means of a computer through serial port using the 5 programmer software which is freely downloadable from www tell hu website Function of the IN4 DIRECT GSM Input Short circuiting the IN4 input the module switches
11. he eventual incoming calls from disturbing the outgoing calls initiated by the alarm system Furthermore incoming calls can be restricted according to telephone numbers This function can only be set in the Call Filter window of the software 5 Settings xj Phone numbers SMS settings Call Filter Output Control Filtering incoming calls Enable all incoming call Enable calls from the following phone numbers only 1 Enabled phone number eat aN A 2 Enabled phone number 3 Enabled phone number He eT 4 Enabled phone number SERRE REE Incoming call time limitation 0 25 min O no limit 25 I Cancel changes The duration of incoming calls can be restricted as well Important note In case of telephone number restriction do not enter the inland area changing prefix before the telephone number only the area code and telephone number The telephone uses international format 3630 while displaying telephone numbers The module compares the received telephone number with the restricted telephone number by starting to compare them from the last digits The module handles the two numbers as identical even if 36 is left out Setting a prefix number necessary to access external PSTN line If the module is connected to a wired network where the dialing of a certain number e g 9 is necessary to access the external PSTN main line this number must be
12. is case GSM Line Pro 5 module will simulate the monitoring station e The adapter can be set to forward the SMS messages arriving to the SIM Card to one or two phone numbers This function makes the use of non subscription cards more secure since the owner user can get the message about the actual balance to his own phone set e In connection with certain special devices e g emergency telephone a telephone number can be set which the module will automatically call when the receiver is picked up e Moreover as a result of short circuit contact IN1 IN2 IN3 inputs it is possible to send an SMS message with pre set text e By means of OUT1 and OUT2 open collector outputs it is possible to turn on and off different devices remotely through a telephone call Operation of the Unit In case of incident the alarm system initiates a call to the monitoring station The adapter continuously watches the existence and the functioning of a wired phone line If there is a functioning wired phone line the unit directs the call to it otherwise if no wired line is connected or the connected line does not work the unit initiates the call through the GSM network Usually an alarm system can be programmed to give a PGM output signal if it could not access the monitoring station on several attempts e g due to some fault in the telephone exchange or sub exchange Connecting the mentioned output of the alarm system to the IN4 DIRECT GSM terminal of t
13. lay By entering 31 before the telephone number telephone number display is enabled on the called person s telephone and by entering 31 this function is disabled 10 PC RS232 Antenna B Metal housing C Antenna adapter cable D GSM Line Adapter Pro 5 Antenna connection F SIM case G GSM module H Supply voltage input terminals 9 24V DC Il RS232 connector for the communication with PC J Connectors GSM LINE 2 wire Generated telephone line PSTN line connector towards the alarm system PSTN 2 wire Connector for incoming wired telephone line IN1 contact input for SMS sending IN2 contact input for SMS sending IN3 contact input for SMS sending IN4 DIRECT GSM function COM common point ground for IN1 IN4 inputs OUT1 output that can be remote controlled through a telephone call open collector 2 output that can be remote controlled through a telephone call open collector output for signaling the failure of GSM line that lasts longer than 3 minutes open collector OUT4 output for signaling the failure of wired line that lasts longer than 3 minutes open collector Incoming wired telephone line PSTN Telephone line input of alarm system Pushbutton 11 Technical specification Supply voltage 9 24V DC Maximum current consumption 500 mA Operating temperature between 10 C and 60 C
14. o not force and drag the antenna cable while fixing it because if mechanical damage occurs it results loss of guarantee Connections e In case a wired telephone line exists connect the ends of the phone line to the terminal PSTN The polarity is indifferent If the PSTN MODE LED lights the line has been connected correctly The signal of PSTN MODE LED is delayed e Connect the phone line input of the alarm system to the GSM LINE output of the GSM adapter with the shortest cable possible Here the polarity is also indifferent Use possibly shielded cable and connect one end of the shielding to the ground potential while leaving the other end free e Installation of further connections IN1 IN2 IN3 IN4 OUT1 OUT2 OUT3 OUT4 can be done if requested see at functions Setting Up e Insert the SIM card in its case if it is necessary in programmed state PIN code request should be disabled e The caller number identification function must be enabled by the GSM service provider on the SIM card a few types of SIM cards do not have this function enabled by default e Make sure that the connections correspond to the above instructions e Apply supply voltage to the unit 9 24V Make sure that the power supply current is sufficient for the load when the alarm system and the adapter are working together The quiescent current of the adapter is 200 mA but the it may increase to 500 mA during communication Setting by means of the
15. r certain period that can be entered in seconds between 0 and 254 for each controllable output If 255 is entered the output becomes bistable and does not turn off automatically Important note Do not use area changing prefix when entering the telephone number use only area code and telephone number the same way as described in Receiving calls through the GSM network section LED Lights of the Unit There are six LED lights on the module indicating the following operational conditions e POWER Indicates that the power supply is on e GSM NETWORK e 5 continuous lighting indicates that the module is connected to the GSM network e If the LED is not lit at all the attempt to sign in the GSM network has failed or is in progress e PSTN MODE indicates the existence of an operating wired telephone line e GSM MODE Indicates that a call is in progress through the GSM network e LED at output OUT3 Indicates that either the GSM module has not been able to connect to the network after trying it for 3 minutes or the field strength has decreased under the required minimal level for more than 3 minutes When the OUT3 LED is lit the output also gets activated and it can be fed back to the alarm system or used for initiating local alarming e LED at output OUT4 Indicates if the wired line has not been in operating mode for more than three minutes At the same time the OUT4 LED signals the OUT output also gets activated and this c
16. rves any incident that has a code starting with the 313 sequence 3130 3139 In case of Ademco Express format you have to create similar SMS messages with the only difference that the incident codes have only two digits e g 31 Burglary Here you can also use the character e g 3 Alarm This message will be sent in case of any incident with a code between 30 and 39 Note By entering character in the text of SMS in the sent SMS the information of event code partition zone will appear instead of Note The module does not perceive signals sent through wired telephone lines Note In Pro5_ programmer when ADEMCO Express code is entered two zeros have to be inserted before the code e g in case of 31 alarm 0031 has to be entered in the program 5 Settings x Phone numbers SMS settings Call Filter Output Control SMS text eee TTT i The character in the SMS text will be replaced to eventcode pattition zone Cancel changes Sending SMS as a result of IN1 IN2 IN3 inputs It is possible to send SMS to telephone numbers USER1 and USER2 due to short circuit impulse on IN1 IN2 IN3 inputs For this enter message the IN1 input IN3 input fields Sending SMS messages on event without being connected to a monitoring station If you do not wish the alarm system s signals to be directed to the monitoring station it is still possible to send
Download Pdf Manuals
Related Search