DSH-142 User manual VA1
Contents
1. 31 Ske USB Connector USB ii u ntn Sasu Sana 32 SEF EMOS DA urlo 32 CHAPTER 4 DRIVERS INSTALLATION oe ee AA U U J 33 4 1 SIR RR dd ao qaa de dos ma muhu 33 CHAPTER 35 AMI BIOS SETUP UTILITY vini eine aaa ec lc ai 35 5 1 0 35 5 2 NAVIGATION S 35 5 3 KET a A RE 36 5 4 Advanced ME se uum as 37 5 5 A 45 5 6 Boo Meer iaa dida 47 5 7 SECU MENU eana N 48 5 8 sn usuy uyu as u Quy aka ua uuu sss 49 APPENDIX A REFERENCE DOCUMENTS U J T T T J 51 APPENDIX B WATCH DOG TIMERu uuu lle 53 MEMO vi OPS830 Series User s Manual CHAPTER 1 INTRODUCTION This chapter contains general information and detailed specifications of the OPS830 Chapter 1 includes the following sections General Description Specification Dimensions I O Outlets Package List 1 1 General Description Intel Open Pluggable Specification OPS Compliance OPS830 is based on the Intel AtomTM D2550 N2800 processor with Mobile Intel NM10 Express chipset The Pluggable Module is targeted to provide an interchangeable solution to the digital signage media players with compatible connector This document provides the module form factor connector specification reference thermal solution and boundary conditions in order to ensure the functionally of the module in all compatible dis2. gt Save Changes and Exit When you have completed the system configuration changes select this option to leave Setup and return to Main Menu Select Save Changes and Exit from the Save Exit menu and press lt Enter gt Select Yes to save changes and exit gt Discard Changes and Exit Select this option to quit Setup without making any permanent changes to the system configuration and return to Main Menu Select Discard Changes and Exit from the Save amp Exit menu and press lt Enter gt Select Yes to discard changes and exit gt Save Changes and Reset When you have completed the system configuration changes select this option to leave Setup and reboot the computer so the new system configuration parameters can take effect Select Save Changes and Reset from the Save 8 Exit menu and press lt Enter gt Select Yes to save changes and reset gt Discard Changes and Reset Select this option to quit Setup without making any permanent changes to the system configuration and reboot the computer Select Discard Changes and Reset from the Save amp Exit menu and press lt Enter gt Select Yes to discard changes and reset AMI BIOS Setup Utility 49 OPS830 Series User s Manual 50 gt gt gt Save Changes When you have completed the system configuration changes select this option to save changes Select Save Changes from the Save amp Exit menu and press lt Enter gt Select Yes to save changes Discard Changes
3. Hardware Installation 17 OPS830 Series User s Manual Step 3 3 Paste the thermal pad on the Wi Fi module and press it firmly Step 3 4 Find the Antenna cable and connect it wireless LAN card Screw the antenna connector at expansion l O side and Install the antenna on the wireless LAN card gt The wireless Module with one antenna application 23235353355 ery I tt dt de 18 Hardware Installation OPS830 Series User s Manual gt The wireless module with two antennas application 4 gt gt na nea po pa gt Step4 Install HDD To enable future remove of HDD please affix the HDD Mylar sheet to the hard disk drive so that it extends past the length of the HDD at the opposite end of the HDD to the Connector Step 4 1 Loosen the screw of HDD cover y Do AMM ont ov mi B sranty cover is rem 2 gt 0008 woens gt SIN WXN1E40HP J85 W YAY i WWN 50014E DCM DBNTJHBB DCX HOD8Z49CP U S Patents 6178056 Product ol Thailand Canada ICES 003 Class DATE 22 SEP Product w label or Hardware Installation 19 OPS830 Series User s Manual Step 4 3 Plug HDD into hard disk drive connector Step 4 4 Pull the HDD Mylar to slot out the hard disk drive 20 Hardware Installation OPS830 Series User s Manual 2 2 Pluggble Module Method v NOTE Please contact Axiomatic for the available option display Step 1
4. are registered trademarks of Intel Corporation MS DOS Microsoft C and Quick BASIC are trademarks of Microsoft Corporation VIA is a trademark of VIA Technologies Inc SST is a trademark of Silicon Storage Technology Inc UMC is a trademark of United Microelectronics Corporation Other brand names and trademarks are the properties and registered brands of their respective owners Table of Contents DIS IA NE Sale V ADO OVAS nnan yaa anclada datado ko an ke ee lil Salely Precautions ias ia IV CHAPTER TINTRODUCTION u i u uu uu u Gu viali 1 1 1 General DOsoOriBUOlis u u u ullu lili 1 1 2 System SDE INCAUONS dt au tu mauka 3 Main GPU BONA us uuu cda 3 li2 2 Ossia 3 1 3 Mechanical ASS em 4 RST Dimension 4 A A 5 3 3 MechanicalSpecilicalionsi sini 6 13 Reference Desi ites uu u uku u ia idad 11 1 4 Package ES emilia 12 CHAPTER 2 HARDWARE INSTALLATION J nanasa 13 2 1 FDB DRAM AVireless Installationi y u u A Lu ee a 13 2 2 Pluggble Module Method a 21 CHAPTER 3 CONNECTORS uu T u dd is 23 3 1 CONE Std dido pisya Sa 23 osti JAETX25 Connecio ON e clarita 27 32 CRPUFAN ONI 28 SS VEA PONENT ciel 29 3 1 4 PCI Express Mini Card Connector SCN1 30 dto Einerne POMS LANI
5. AXIOMTEK OPS830 Series Intel Open Pluggable Specification Box User s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information Axiomtek Co Ltd assumes no responsibility for any infringements of patents or any third party s rights and any liability arising from such use Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of any information in this document Axiomtek does not make any commitment to update the information in this manual Axiomtek reserves the right to change or revise this document and or product at any time without notice No part of this document may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of Axiomtek Co Ltd OCopyright 2012 Axiomtek Co Ltd All Rights Reserved September 2012 Version A1 Printed in Taiwan Safety Approvals CE Marking FCC Class A This equipment has been tested in compliance with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are meant to provide reasonable protection against harmful interference in a residential installation If not installed and used in accordance with proper instructions this equipment might generate or radiate radio frequency energy and cause harmful i
6. key or the lt Enter gt keys to move between fields The date must be entered in MM DD YY format The time is entered in HH MM SS format 36 AMI BIOS Utility Setup Utility OPS830 Series User s Manual 5 4 Advanced Menu e Launch PXE OpROM Use this item to enable or disable the Boot ROM function of the onboard LAN chip when the system boots up e Launch Storage OpROM This item can set enable or disable the storage device option ROM with CF device The Advanced menu also allows users to set configuration of the CPU and other system devices You can select any of the items in the left frame of the screen to go to the sub menus e ACPI Settings S5 RTC Wake Settings CPU Configuration SATA Configuration IDE Configuration USB Configuration F81801 Super lO Configuration F81801H W Monitor For items marked with gt please press lt Enter gt for more options AMI BIOS Setup Utility 37 OPS830 Series User s Manual e ACPI Settings You can use this screen to select options for the ACPI Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen Aptio Setup Utility Copyright C 2011 American Megatrends Inc ACPI Sleep State S3 Suspene to RAM Version 2 14 1219 Copyright C 2011 American Megatrends Inc gt ACPI Sleep State Allow you to select the Advanced Configuration and Power Interface ACPI state to be used f
7. Pluggable the box into display Step 2 Fasten the screws as illustrated Hardware Installation 21 OPS830 Series User s Manual MEMO 22 Hardware Installation OPS830 Series User s Manual CHAPTER 3 CONNECTORS This chapter provides users with detailed description how to set up basic system configuration through the AMIBIOS8 BIOS setup utility 3 1 Connectors Connectors connect this board with other parts of the system Loose or improper connection might cause problems Make sure all connectors are properly and firmly connected Here is a summary table shows you all connectors on the board Connectors 23 OPS830 Series User s Manual DO LT A pr F I OJ 32 49 N N N O onoonooocooooconoococooco GO V O O GO V O OD O O O O O V G O fl Do 12 of jo To SCN4 S NJ 1 52 MO of ja 70 Connectors 24 OPS830 Series User s Manual no O 00000000000000000000 i 00000000000000000000 00000000000000000000 CN4 BAT1 OPSI830 Made In Taiwan USB1 LANI 39968 CN7 CNS LNO 25 Connectors OPS830 Series User s Manual O Q P QUIS Ida Is o O O 26 TE Connectors 3 1 1 JAE 725 Connector CN1 DDP_3N DDP_3P OPS830 Series User s Manual GND DDP_2N DDP_2P GND DDP_1N DDP_1P GND DDP_ON DDP_0P GND DDP_AUXN DDP_AUXP DDP_HPD GN
8. Select this option to quit Setup without making any permanent changes to the system configuration Select Discard Changes from the Save Exit menu and press lt Enter gt Select Yes to discard changes Restore Defaults It automatically sets all Setup options to a complete set of default settings when you select this option The Optimal settings are designed for maximum system performance but may not work best for all computer applications In particular do not use the Optimal Setup options if your computer is experiencing system configuration problems Select Restore Defaults from the save amp Exit menu and press lt Enter gt Save as User Defaults Restore User Default UEFI Built in EFI Shell This function is use EFI shell to boot up the system AMI BIOS Utility Setup Utility OPS830 Series User s Manual APPENDIX A REFERENCE DOCUMENTS Document Document No Location Digital Signage Open Pluggable Specification 324427 JAE TX24 TX25 connector product brief JAE plug connector details and drawing i ttp lae JAE receptacle connector details and drawing h ttp jae 1X24 80R E H1E Reference Documents 51 OPS830 Series User s Manual MEMO 52 Reference Documents OPS830 Series User s Manual APPENDIX B WATCH DOG TIMER About Watchdog Timer Software stability is major issue in most application Some embedded systems are not watched by human for 24 hours lt is usually too slow to wait for some
9. The lt F1 gt key allows you to display the General Help screen F2 The lt F2 gt key allows you to Load Previous Values F3 The lt F3 gt key allows you to Load Optimized Defaults The lt F4 gt key allows you to save any changes you have made and exit F4 Setup Press the lt F4 gt key to save your changes The lt Esc gt key allows you to discard any changes you have made and exit the Setup Press the lt Esc gt key to exit the setup without saving your changes The lt Enter gt key allows you to display or change the setup option listed for a particular setup item The lt Enter gt key can also allow you to display the setup sub screens AMI BIOS Setup Utility 35 OPS830 Series User s Manual 5 3 Main Menu When you first enter the Setup Utility you will enter the Main setup screen You can always return to the Main setup screen by selecting the Main tab There are two Main Setup options They are described in this section The Main BIOS Setup screen is shown below Aptio Setup Utility Copyright C 2011 American Megatrends Inc Advanced Chipset Boot Security Save Exit System Date Version 2 14 1219 Copyright C 2011 American Megatrends Inc gt System Date Time Use this option to change the system date and time Highlight System Date or System Time using the lt Arrow gt keys Enter new values through the keyboard Press the lt Tab gt
10. _ 30 Connectors OPS830 Series User s Manual 3 1 5 Ethernet Ports LAN1 The RJ 45 connector LAN1 is for Ethernet To connect the board to 100 Base T or 1000 Base T hub just plug one end of the cable into LAN1 and connect the other end phone jack to a 100 Base T hub or 1000 Base T hub Active LED Yellow O B 100 LAN LED Green 1000 LAN LED Orange L8 L7L6 L5L4 L3 L2 L1 Connectors 31 OPS830 Series User s Manual 3 1 6 USB Connector USB1 The board features Universal Serial Bus USB connectors compliant with USB 2 0 480Mbps that can be adapted to any USB peripherals such as monitor keyboard and mouse This USB1 connector carries USB port 0 and 1 em USB Port 0 e USB Port 1 USB VCC USB VCC 5V standby power 5V standby power USBHOLD USBHOLD D p USB D p USB D _D ERE CS AT 3 1 7 CMOS battery BAT1 32 Connectors OPS830 Series User s Manual CHAPTER 4 DRIVERS INSTALLATION 41 System OPS830 supports Window 7 To facilitate the installation of system driver please carefully read the instructions in this chapter before start installing 1 Insert Intel Express Installer Driver CD and select the Driver 2 Select your operating system driver to install _ 7 am _ lL Fa Optional_WiFi Step 1 Chipset Step 2 Graphic Step 3 LAN Step 4 HD Audio 3 Select all files and foll
11. ports 2 0 One Power on Off button One Reset button e Ethernet m 10 100 1000Mbps Ethernet e Audio m Line out Mic in e Expansion One PCI Express Mini Card slot is equipped for optional add on such as wireless LAN card for 802 11 a b g n connections GPS Bluetooth application e Storage m One 2 5 SATA HDD tray e Net Weight m 0 9Kg 1 99 Ib without cooler e Dimension Main Body Size 200mm W x 119 mm D x 30 mm H e Operation Temperature m OC to 45 with airflow 0 7 m s OPS compliant lt mai NOTE All specifications and images are subject to change without notice Introduction 3 OPS830 Series User s Manual 1 3 Mechanical Assembly 1 3 1 Dimensions This diagram shows you dimensions and outlines of the OPS830 The overall dimension of the module including the mounting frame is 200mm x 119mm x 30mm and also shows the location of the front panel screw holes as well as the security lock 120 00 Remark While plugging the OPS module please make sure the heat sink side of OPS module Toward the outside Axiomtek will be out of reasonability if there is any damage occurred due to it Introduction OPS830 Series User s Manual 1 3 2 IO out let The following figures show you the locations of the OPS830 I O outlets o Jem w eman a eo l o jue Co O INC Poema p Jie OTC Introduction 5 OPS830 Series User s Manual 1 3 3 Mechanical Specifications gt OPS830 Dock
12. 000000000 90000000000000000000000000000000000000000000 6000000000000000000000000000000000000000000 o AA lo o o o 00000000000000000000000000000000000000000 00000000000000000000000000000000000000000 00000000000000000000000000000000000000000 00000000000000000000000000000000000000000 00000000000000 AIA Sees le oe eo Soo PRA lis ro 000000000000000 0 00000000000000 4 The digital signage OPS830 prototype is based on a 32 display panel with the functional It is mainly a 3 board partitioning design illustrated in Figure 18 blocks docking board and the panel control board consisting of the pluggable module 11 Introduction OPS830 Series User s Manual 1 4 Package List When you receive the OPS830 the bundled package should contain the following items OPS830 device x 1 Driver CD x 1 HDD Mylar x 1 THERMAL GREASE Syringe 1G M3 x 4 screw x 2 M4 x 6 screw x 2 If you can not find the package or any items are missing please contact Axiomtek distributors immediately 12 Introduction OPS830 Series User s Manual CHAPTER 2 HARDWARE INSTALLATION The OPS830 are convenient for your various hardware configurations such as HDD Hard Disk Drive Memory Module The chapter 2 will show you how to install the hardware lt includes e Hard disk drive and DRAM Installation e Pluggable Module Method 2 1 HDD
13. D TMDS_CLK TMDS_CLK GND TMDSO TMDSO GND TMDS1 TMDS1 GND TMDS2 TMDS2 GND DVI_DDC_DATA DVI_DDC_CLK DVI_HPD GND 12V 4 19V 12V 19V 12V 19V 12V 4 19V 12V 19V 12V 19V 12V 4 19V 12V 4 19V NC NC NC NC NC NC SYS_FAN_CTL UART_RXD UART_TXD GND NG NG GND NC NC GND USB_PN2 USB_PP2 GND USB_PNI USB_PP1 GND USB_PNO USB_PPO GND LINEOUT_L LINEOUT_R NG PB_DET PS_ON NC GND GND GND GND Connectors 27 OPS830 Series User s Manual Lil HI lalla alll al ala i AMMA NA lalla della 1013 07 N A SZKL o 6 s m K RARE EI ANDER PERRO RE RRR ORES POPES RS 3 1 2 CPU FAN vile a CPU fan interface 28 Connectors OPS830 Series User s Manual 3 1 3 VGA Port CN7 DB15 CRT Connector CN7 Co layout with CN4 CN7 is a DB15 connector commonly used for the CRT Monitor Horizontal Sync Vertical Sync 15 DDC CLK Connectors 29 OPS830 Series User s Manual 3 1 4 PCI Express Mini Card Connector SCN1 The SCN1 is a PCI Express Mini Card connector which supports a PCI Express x1 link and a USB 2 0 link A PCI Express Mini Card can be applied to either PCI Express or USB 2 0 lt complies with PCI Express Mini Card spec v1 2 s u a 7 RT w
14. DRAMI Wireless Installation The OPS830 Series offers a convenient drive bay module for users to install DRAM and HDD Please follow the steps Step 1 Turn off the system and loosen the screws as illustrated Hardware Installation 13 OPS830 Series User s Manual Y y NOTE Please be reminded to smear the grease over the PCH and upper side of CPU 14 Hardware Installation OPS830 Series User s Manual Step 2 Install DRAM Step 2 1 Loosen the screws on the real of chassis as illustrated Hardware Installation 15 OPS830 Series User s Manual Step 2 2 After losing the screws extract the real of chassis out of the module Step 2 3 Install DRAM module Put DRAM Place the memory module into the socket and press it firmly The socket latches are levered upwards and clipped on to the edges of the DIMM 16 Hardware Installation OPS830 Series User s Manual Step 3 Install Wireless Module The OPS830 provides one Mini card slot for user to install one wireless LAN card When installing the wireless LAN card refer to the following instructions and illustration Step 3 1 Please refer to Step 1 to loosen the screws of the chassis and PCB board Turn over the PCB board Step 3 2 Install Wi Fi module Place the Wi Fi module into the socket and press it firmly down until it is fully located edi ve Pi be a spa sb a 4 z ga s e Va fil Dr He ozi
15. Lock holes x4 Top View The drawing is base on Intel Open Pluggable Specification 8 Introduction OPS830 Series User s Manual gt Dimensions of the Guide Rail Introduction 9 OPS830 Series User s Manual 10 Location of JAE TX25 Plug Connector Please refer to the following drawing for location of the JAE TX25 plug connector Pin 1 of the connector is located at 114 8 mm from the edge of the module and 106 9 mm from the inner side of the front panel For mating tolerance of TX25 plug connector and TX24 receptacle connector please refer to the JAE specification r 114 879 j da TOT PUB Thickness L 5 PCB Location lg JE IE m i MITI e E 100 100 200 Vent Holes at the Pluggable Module Back Panel On the OPS830 Module it is recommended by Intel that some vent holes be opened at the back so that hot air can escape more easily from the module that the FAR in on both sides of the module back panel should be greater than 0 25 SECTION AA AA Grille area di x 2Bmm FAR gt 0 25 Introduction OPS830 Series User s Manual Reference Design 1 3 4 Display Panel Rear View Internal NaS Cao a a were O O O O O O O O O O O O OO 00900000000000O0 Of o 0000000000000O0 000000000000000 909007079 000000000000000 0000000000000000000000000000000000000000000 90000000000000000000000000000000000
16. ed in the Reference Display Panel The OPS 830 Pluggable Module docked at a display panel system In this reference design the module is docked and undocked in the vertical direction lt YY NOTE Please contact Axiomtek for available option display panel 378 00 TO P F ae k k Pat a z a tata a A z E era ieee atarata ateraia c ii a CTL Te ee ey 11 5 J 5 5 Pluggable Module Bottom 6 Introduction OPS830 Series User s Manual gt Exploded View of the Pluggable Module 1 ari AJA gt A A V gt The Guide Rail Mechanism for the OPS830 Module You can use the rails along side of OPS830 module to dock and undock the plug connector at the back of the module to connect with docking board There are two lock pins on each side of the rail which serve as the locking mechanism to attach the lock holes on the OPS830 module Plug connector Receptacie Lock Hole Lock Pin FRONT VIEW BACK VIEW Introduction 7 OPS830 Series User s Manual gt Location of Lock Hole on the Pluggable Module SEE DETAIL B 00000000000000 000000000000 N 0000000000000 000000000000 0000000000000 000000000000 0000000000000 000000000000 0000000000000 000000000000 00000000000000 000000000000 SEE DETAIL A 00 DETAIL A e R1 SCALE 2 1 Lock holes x4 a Side View Ne DETAIL B SCALE 2 1
17. n 2 14 1219 Copyright C 2011 American Megatrends Inc AMI BIOS Setup Utility 41 OPS830 Series User s Manual e USB Configuration You can use this screen to select options for the USB Configuration and change the value of the selected option A description of the selected item appears on the right side of the screen Aptio Setup Utility Copyright C 2011 American Megatrends Inc Legacy USB Support Enabled Version 2 14 1219 Copyright C 2011 American Megatrends Inc gt Legacy USB Support This is for supporting USB device under legacy OS such DOS when choosing AUTO the system will automatically detect any USB device is plugged into the computer and enable USB legacy mode when a USB device plugged and disable USB legacy mode when no USB device is plugged 42 AMI BIOS Utility Setup Utility OPS830 Series User s Manual e F810801 Super IO Configuration This is set parameters of serial pot 0 Aptio Setup Utility Copyright C 2011 American Megatrends inc gt Serial Port 0 Configuration Version 2 14 1219 Copyright C 2011American Megatrends Inc AMI BIOS Setup Utility 43 OPS830 Series User s Manual eo F810801 HW Monitor This screen shows the Hardware Health Configuration and a description of the selected item appears on the right side of the screen Aptio Setup Utility Copyright C 2011 American Megatrends Inc Version 2 14 1219 Copyright C 2011 America
18. n Megatrends Inc 44 AMI BIOS Utility Setup Utility OPS830 Series User s Manual 5 5 Chipset Menu Aptio Setup Utility Copyright C 2011 American Megatrends Inc Main Advanced Set Boot Security Save amp Exit p Host Bridge Version 2 14 1219 Copyright C 2011 American Megatrends Inc AMI BIOS Setup Utility 45 OPS830 Series User s Manual e Host Bridge This feature is to consign memory frequency and timing settings e South Bridge This feature is to enable and disable Intel lO controller Hub TPT devices Aptio Setup Utility Copyright C 2011 American Megatrends Inc p Memory Frequency and Timing Version 2 14 1219 Copyright C 2011 American Megatrends Inc Aptio Setup Utility Copyright C 2011 American Megatrends Inc p TPT Devices Version 2 14 1219 Copyright C 2011 American Megatrends Inc 46 AMI BIOS Utility Setup Utility OPS830 Series User s Manual 5 6 Boot Menu The Boot menu allows users to change boot options of the system You can select any of the items in the left frame of the screen to go to the sub menus e Setup Prompt Timeout Boot up Mum Lock State Quiet Boot CSM16 Module Version Boot Option Priorities Aptio Setup Utility Copyright C 2011 American Megatrends Inc Main Advanced Chipset OO Security Save amp Exit Setup Prompt Timeoutoot Version 2 14 1219 Copyright C 2011 American Megatrends Inc gt Setup Prom
19. nterference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following methods 1 Increase the separation between the equipment and receiver 2 Connect the equipment to another outlet of a circuit that doesn t connect with the receiver 3 Consult the dealer or an experienced radio T V technician for help Shielded interface cables must be used in order to comply with the emission limits ili Safety Precautions Before getting started please read the following important safety precautions 1 The OPS830 does not come equipped with an operating system An operating system must be loaded first before installing any software into the computer 2 Be sure to ground yourself to prevent static charge when installing the internal components Use a grounding wrist strap and place all electronic components in any static shielded devices Most electronic components are sensitive to static electrical charge 3 Disconnect the power cord from the OPS830 before any installation Be sure both the system and external devices are turned OFF A sudden surge of power could ruin sensitive components that the OPS830 must be properly grounded 4 Make sure it is the cor
20. one to reboot when computer hangs The systems need to be able to reset automatically when things go wrong The watchdog timer gives us solution The watchdog timer is a counter that triggers a system reset when it counts down to zero from a preset value The software starts counter with an initial value and must reset it periodically If the counter ever reaches zero which means the software has crashed the system will reboot How to Use Watchdog Timer The I O port base addresses of watchdog timer are 2E hex and 2F hex The 2E hex and 2F hex are address and data port respectively Assume that program A is put in a loop that must execute at least once every 10ms Initialize watchdog timer with a value bigger than 10ms If the software has no problems watchdog timer will never expire because software will always restart the counter before it reaches zero Watch Dog Timer 53 OPS830 Series User s Manual Enable and Initialize Watchdog Timer Program A Disable Watchdog Timer 94 Enable and Initialize Watchdog Timer Program A Reset Watchdog Timer Watch Dog Timer Sample Program Assembly sample code Enable WDT mov dx 2Eh mov al 87 out dx al out dx al Select Logic device mov dx 2Eh mov al 07h out dx al mov dx 2Fh mov al 07h out dx al WDT Device Enable mov dx 2Eh mov al 2Bh out dx al mov dx 2Fh mov al 00h out dx al mov dx 2Eh mov al 30h out dx al mov d
21. or system suspend Here are the options for your selection S1 CPU Stop Clock S3 Suspend to RAM and Suspend Disable 38 AMI BIOS Utility Setup Utility OPS830 Series User s Manual e S5 RTC Wake Settings This function is to enable or disable system wake on alarm event When it is enabled system will wake on the hr min sec specified Aptio Setup Utility Copyright C 2011 American Megatrends Inc Wake system with Fixed Time Disabled Version 2 14 1219 Copyright C 2011 American Megatrends Inc AMI BIOS Setup Utility 39 OPS830 Series User s Manual e CPU Configuration This screen shows the CPU Configuration and you can change the value of the selected option Aptio Setup Utility Copyright C 2011 American Megatrends Inc Hyper Threading Enabled Version 2 14 1219 Copyright C 2011 American Megatrends Inc gt Hyper Threading This feature is to enable and disable hyper threading function gt Execute Disable Bit Execute Disable Bit is a hardware based security feature that can reduce exposure to viruses and malicious code attacks and prevent harmful software from executing and propagating on the server o network 40 AMI BIOS Utility Setup Utility OPS830 Series User s Manual e IDE Configuration This function is the SATA Ports device names if present and enabled Aptio Setup Utility Copyright C 2011 American Megatrends Inc SATA Controller Enabled Versio
22. ow the installing procedure You may also link to www axiomtek com for more information Drivers Installation 33 OPS830 Series User s Manual MEMO 34 Drivers Installation OPS830 Series User s Manual CHAPTER 5 AMI BIOS SETUP UTILITY This chapter provides users with detailed description how to set up basic system configuration through the AMIBIOS8 BIOS setup utility 5 1 Starting To enter the setup screens follow the steps below gt Turn on the computer and press the lt F2 gt key immediately gt After you press the lt F2 gt key the main BIOS setup menu displays You can access the other setup screens from the main BIOS setup menu such as the Chipset and Power menus 5 2 Navigation Keys The BIOS setup utility uses a key based navigation system called hot keys Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process These keys include lt F1 gt lt F2 gt lt Enter gt lt ESC gt lt Arrow gt keys and so on V NOTE Some of navigation keys differ from one screen to another Left Right The Left lt Arrow gt keys allow you to select a setup screen The Up and Down lt Arrow gt keys allow you to select a setup screen or sub screen MV Up Down The Plus and Minus lt Arrow gt keys allow you to change the field value of a Plus Minus particular setup item Tab The lt Tab gt key allows you to select setup fields F1
23. play panel system OPS830 meets Intel Open Pluggable Specification for design and development simplifying system upgrade maintenance for manufacturers and developers that supports not only is high flexible and user friendly digital signage applications also significantly provides superb graphics performance full HD content playback Introduction 1 OPS830 Series User s Manual Easy maintenance OPS830 offers a best solution for digital signage market Compliant with Intel OPS architecture digital signage players are capable of deploying interchangeable systems faster and easing upgrading maintenance while lowering costs for development and implementation Additionally having the ability to simply slot in and out the unique pluggable engine box makes daily hassle easier and faster for users OPS830 has pluggable engine box design you can change HDD DRAM and configurations more easily 2 Introduction OPS830 Series User s Manual 1 2 System Specifications 1 2 1 Main CPU Board e CPU ia Intel Atom D2550 N2800 processor on board e System Chipset m Intel NM10 e BIOS AMI BIOS e System Memory One socket 204 pin DDR3 SODIMM system memory up to 4GB e Wireless Module Optional IEEE802 11 a b g n Bluetooth 2 0 Remark Suggest disable Aero Peek function the following route under OS Win 7 is Start Control panel System and Security System Enable Aero Peek 1 2 2 IO System 9 Standard I O One VGA Two USB
24. pt Timeout Set the Timeout for wait press key to enter Setup Menu gt Boot up Mum Lock State Use this item to select the power on state for the Mum Lock The default setting iS on gt Quiet Boot Use this item to enable or disable the Quite Boot state The default setting is disabling gt Boot Option 1 AMI BIOS Setup Utility 47 OPS830 Series User s Manual 5 7 Security Menu The Security menu allows users to change the security settings for the system Aptio Setup Utility Copyright C 2011 American Megatrends Inc Main Advanced Chipset Boot lt T Save amp Exit Administrator Password Version 2 14 1219 Copyright C 2011 American Megatrends Inc gt Administrator Password This item indicates whether an administrator password has been set If the password has been installed Installed displays If not Not Installed displays gt User Password This item indicates whether a user password has been set lf the password has been installed Installed displays If not Not Installed displays 48 AMI BIOS Utility Setup Utility OPS830 Series User s Manual 5 8 Save Exit Menu The Save amp Exit menu allows users to load your system configuration with optimal or failsafe default values Aptio Setup Utility Copyright C 2011 American Megatrends Inc Main Advanced Chipset Boot Security Restore Defaults Version 2 14 1219 Copyright C 2011 American Megatrends Inc
25. rect voltage of the power source before connecting the equipment to the power outlet 5 The brightness of the flat panel display will be getting weaker as a result of frequent usage However the operating period varies depending on the application environment 6 The flat panel display is not susceptible to shock or vibration When assembling the OPS830 make sure it is securely installed 7 Do not leave this equipment in an uncontrolled environment where the storage temperature is below 0 C or above 40 C lt may damage the equipment 8 External equipment intended for connection to signal input out or other connectors shall comply with relevant UL IEC standard 9 Do not open the back cover of the system If opening the cover for maintenance is a must only a trained technician is allowed to do so Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the following precautions Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This will help to discharge any static electricity on your body Vhen handling boards and components wear a wrist grounding strap available from most electronic component stores Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co Ltd IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation Intel and Atom
26. x 2Fh mov al 01h out dx al Activate WDT mov dx 2Eh mov al OFOh out dx al mov dx 2Fh mov al 80h out dx al Set Second or Minute mov dx 2Eh mov al 0F5h out dx al mov dx 2Fh mov al Nh out dx al Watch Dog Timer Un lock super I O N 71h or 79h see below Y Note OPS830 Series User s Manual 99 OPS830 Series User s Manual Set base timer mov dx 2Eh mov al OF6h out dx al mov dx 2Fh mov al Mh M 00h 01h FFh hex Value 0 to 255 out dx al see below v Note Disable WDT mov dx 2Eh mov al 30h out dx al mov dx 2Fh mov al 00h Can be disabled at any time out dx al W Note If N 71h the time base is set to second M time value 00 Time out Disable 01 Time out occurs after 1 second 02 Time out occurs after 2 seconds 03 Time out occurs after 3 seconds FFh Time out occurs after 255 seconds If N 79h the time base is set to minute M time value 00 Time out Disable 01 Time out occurs after 1 minute 02 Time out occurs after 2 minutes 03 Time out occurs after 3 minutes FEh Time out occurs after 255 minutes 96 Watch Dog Timer
Download Pdf Manuals
Related Search