USER MANUAL - KingsBottle
Contents
1. www kingsbottle com 1 Low Set Point Limit 18 F Set Temp 32 F E2 High Set Point Limit Set Temp 46 F 46 E3 Temp differential 01 F 18 F 07 F E4 Start delay when COMPRESSOR ON is required by the 00 10 Min 4 Min Regulation E5 Offset on room temp 36 F 36 F 0 F Offset on room temp 36 F 36 F E8 Compressor continuously work time 00 24 Hours 6 Hr E9 Compressor force stop time 01 60 Min 20 Min F1 Max Defrost duration 01 60 Min 30 Min F2 Defrost interval time 00 24 Hours 6 Hr F3 Defrost termination temp 32 F 104 F 53 F F4 Display during defrost 00 Normal Display 01 Last value before 01 defrost L1 Light control select 00 Door switch control 01 Manual 00 control CF Temperature C F selection C Celsius F Fahreheit Circuit Schematic Diagram M1 Power plug Temperature control ler www kingsbottle com 9 0 6 Cold room Sensor Connect the main contro board Connect the Display board NOTE The desired temperatures may fluctuate depending on whether the interior light is ON or OFF the ambient temperature the location of unit and the orientation of the bottles The display is just a guide be guided by how cold your drinks are at consumption Remember units go into defrost mode and this will show a higher display it s only for small periods and doesn t have time to effect drink temperatu2. Remove the exterior and interior packing 2 Before connecting the Beverage Cooler to the power Source let it stand upright for approximately 24 hours This will reduce the possibility of a malfunction in the cooling system from handling during transportation 3 Clean the interior surface with lukewarm water using Soft cloth PART Il DIAGRAM amp DESCRIPTION OF BEVERAGE COOLER Table surface Box body Bullet foot Rack Machine Room Air cooling Evaporator www kingsbottle com 4 PART INSTALLATION INSTRUCTIONS When moving your Beverage Cooler please Locate the Beverage Cooler away from direct sunlight do not incline it more than 45 degrees and sources of heat stove heater radiator etc Leakage breaker 15mA 277 27 socket with ground terminal Install ground fault circuit interrupter to ensure safety d E This free standing model requires adequate ventilation around minimum 6 150mm on either side and the rear is requested Theel Wheels of refrigerator need to be locked with wood or other hard articles to avoid any movement Cushion block www kingsbottle com 5 PART Ill INSTALLATION INSTRUCTIONS A GENERAL INSTALLATION INSTRUCTIONS 1 2 This appliance is designed for free standing Place your Beverage Cooler on a flat solid floor that is strong enough to support it wh
3. directly from BTO AMERICA LIMITED Limited warranty If your refrigerator is not operating KingsBottle reserves the right to repair or replace the refrigerator KingsBottle may request the consumer to contact a local refrigeration company to service the refrigerator All cost for labor and materials is covered for 1 year from the date of receipt If KingsBottle deems the unit not repairable KingsBottle will use the value of your original order toward a replacement For customer service please contact BTO AMERICA LIMITED by e mail service kingsbottle com The limited warranty does not cover Damage due to such things as accident misuse abuse mishandling neglect unauthorized repair or any other cause beyond the control of the seller whether similar or dissimilar to the foregoing Purchaser understands and acknowledges that the goods sold here are Beverage Coolers which house wine Purchaser assumes all the risk of using these units including risk of spoilage humidity variations temperature variations leaks fires water damage mold mildew dryness and similar perils that may occur SPECIAL NOTE Warranty is only honored for the unit which is purchased and used in United States of America And if your product was purchased at any 3rd party retailer and not directly from KingsBottle we do not offer an extended warranty policy You MUST contact the retailer of purchase directly In the event your retailer does not offer an e
4. efficiently 4 Nevertry to adjust shelf with bottles still on it e How to use your shelving You can put the beer bottles on the shelving any way you like lay down or upright Max Weight per shelf 55 Ibs 25kgs To adjust shelving clips can be moved place top part of clip in first then force bottom part up If clips seem loose remove and expand the width of opening on clip this will allow it to fit better K type bars Rack ay Vere ee PLEASE NOTE Before modifying your cabinet s original configuration in any way be sure to ask your dealer for advice www kingsbottle com 11 PART VI CARE AND MAINTENANCE CLEANING YOUR BEVERAGE COOLER AN WARNING BEFORE CLEANING Turn off the power unplug the appliance and remove all items including all shelves e Wash the inside surfaces with warm water and baking soda solution The solution should be about 2 tablespoons of baking soda with a quart of water e Wash the shelves with a mild detergent solution e Wring excess water out of the sponge or cloth when cleaning area of the controls or any electrical parts e Wash the outside cabinet with warm water and mild liquid detergent Rinse well and wipe dry with a clean soft cloth e After installation we recommend that owners apply a thin layer of Olive Oil with a clean rag to all exposed Stainless Steel areas This should then be polished in and buffed off with another clean rag to a non oily finish This
5. process will aid protection against dirt and other corrosive contaminants by providing a temporary food safe shield The Olive Oil layer also makes later polishing and removal of fingerprints easier This process should be repeated frequently every 3 4 months ALL stainless steel can rust it is a myth that stainless steel doesn t rust POWER FAILURE Most power failures are corrected within a few hours and should not affect the temperature of your appliance if you minimize the number of times the door is opened If the power is going to be off for a longer period of time you need to take the proper steps to protect your contents FILTER CLEANING PLEASE INSPECT amp CLEAN FRONT GRILL FILTER EVERY MONTH Failure to clean will void the warranty and increase the running costs VACATION TIME Short vacations You may leave the Beverage Cooler operating during vacations of less than three weeks Long vacations If the appliance will not be used for several months remove all items and turn off the appliance Clean and dry the interior thoroughly To prevent mold growth leave the door open slightly blocking it open if necessary MOVING YOUR BEVERAGE COOLER Remove all items Securely tape down all loose items shelves inside your appliance Turn the adjustable leg up to the base to avoid damage Tape the door shut Be sure the appliance stays secure in the upright position during transportation Also protect the outside of the appliance wi
6. E2 2 Light control When L1 1 2 1 Press SET LIGHT button to turn ON OFF the light 3 Manual enter end defrost 3 1 Press DEFROST button and hold up to 6 seconds enter or end defrost 4 Display the evaporator sensor temperature 4 1 Press DEFROST button once will flash display evaporator sensor temperature after 6 seconds will resume to display cold room temperature 5 Parater setup 5 1 Press SET LIGHT button and hold for 6 seconds at the same time to enter the parameter setup mode while E1 flashed 5 2 Press SET LIGHT button and change the parameter sequentially display from the parameters E2 E3 E6 F1 F4 CF E1 5 8 Press UP or DOWN button the value of parameter will be displayed and can be modified and stored 5 4 f no more button is pressed within 6 seconds it will return to normal operation mode 6 Factory default resumption 6 1 Press UP and DOWN button at the same time and hold up to 6 seconds will flash and display 888 all parameters and set temperature will resume to factory defaults 6 2 After 6 seconds it will return to normal operation mode 7 Lock parameter 7 1 Press SET LIGHT button and hold up to 6 seconds parameter is lock if OFF is displayed or parameter is unlock if ON is displayed 7 2 Parameter can be displayed only and can not be modified but the adjustment of set temperature is still active the factory default is ON www kingsbottle com 7
7. USER MANUAL KBU380 SERIES BEVERAGE COOLER eer COMPRESSOR BEVERAGE COOLER www kingsbottle com CONGRATULATIONS TABLE OF CONTENTS CHAPTER CONTENTS PAGE Congratulations and thank you for choosing our KingsBottle Beverage Coolers We are sure you will find your new appliance a Part Important Safety amp Pre Use Instructions 3 pleasure to use Before you installing and operating the Beverage Cooler we Part II Diagram amp Description of Beverage Cooler 4 recommend that you read through the relevant sections of this manual which provides a description of your Beverage Part Ill Installation Instructions 5 6 Cooler and its functions Part IV Operating Your Beverage Cooler 7 10 To avoid the risks that are always present when you use an electric appliance it is important that the appliance is installed Layout amp Storage 11 correctly and that you read the safety instructions carefully to avoid misuse and Part VI Care and Maintenance 2 hazards Part VII Troubleshooting Guide 13 We recommend that you keep this instruction booklet for future reference and pass it on to any future owners Part VIII Technical Data 14 After unpacking the appliance please check Part IX Warranty Information 16 it is not damaged If in doubt do not use the appliance but contact us or your local customer care centre www kingsbottle com 2 PART IMPORTANT SAFETY INSTRUCTIONS Please read the user manual c
8. arefully and store in a handy place for later reference The symbols you will see in this booklet have these meanings AN WARNING This symbol indicates information concerning your personal safety AN CAUTION This symbol indicates information on how to avoid damaging the appliance TIPS amp INFORMATION This symbol indicates tips and information about use of the appliance M ENVIRONMENTAL TIPS This symbol indicates tips and information about economical and ecological use of the appliance A WARNING TO REDUCE THE RISK OF FIRE ELECTRICAL SHOCK OR INJURY WHEN USING YOUR APPLIANCE FOLLOW THESE BASIC PRECAUTIONS 1 Read all instructions before using the Beverage Cooler 2 DANGER or WARNING Risk of child entrapment Child entrapment and suffocation are not only problems of the past Junked or abandoned appliances are still dangerous even if they will just sit in the garage for a few days 3 Before you throw away your old Beverage Cooler e off the door e Leave the Shelves in pieces so that children may not climb inside easily 4 Never allow children to operate play with or crawl inside the appliance 5 Never clean appliance parts with flammable fluids The fumes can create a fire hazard or explosion 6 Do not store in the vicinity of any other appliance Do not store near gasoline or any other flammable vapors The fumes can create a fire hazard or explosion AN WARNING 1 The cooler must be p
9. en it is fully loaded To level your Beverage Cooler adjust the leveling leg at the bottom of the Beverage Cooler When moving your Beverage Cooler please do not incline it more than 45 degrees Locate the Beverage Cooler away from direct sunlight and sources of heat stove heater radiator etc Direct sunlight and heat sources may increase electrical consumption Extreme cold ambient temperatures may also cause the unit to perform improperly Avoid locating the unit in damp areas Install ground fault circuit interrupter to ensure safety Plug the Beverage Cooler into an exclusive properly installed and grounded wall outlet Do not under any circumstances cut or remove the third ground prong from the power cord Any questions concerning power and or electrical grounding should be directed to a certified electrician or authorized products service center INSTALLING YOUR BEVERAGE COOLER Move the appliance into its final position If the appliance is not tilting back as described earlier minor adjustments can be made to the leveling legs Compare the alignment of the appliance to the surrounding cupboard The top of the appliance should be level from side to side see diagram below Spirit level If the appliance now rocks from one corner to the opposite rear corner this means that the floor is uneven You may need to put some packing under the ridge to the rear of the appliance You could use thin pieces of solid material
10. he door is opened too often Reduce the times frequency of door opening The Cooler seems to make too much noise The stand feet is not leveling vibrations lead to noise Adjust the stand feet and assure they are on level Pipe hit other objects and lead to noise Adjust the position of pipe slightly At the moment of compressor shut down or start it is normal for the noise from the vibration generated by the internal moving parts due to inertial motion nothing is necessary The ratting noise may come from the flow of the refrigerator which is normal As each cycle ends you may hear gurgling sounds nothing is necessary www kingsbottle com 13 PART VIII TECHNICAL DATA MODEL NO KBU380 VOLUME 18 42 CF 380 Liter TYPE OF COOLING compressor CLIMATE TYPE N ST ELECTRICITY PROTECTION GRADE NOMINAL VOLTAGE FREQUENCY 110 115V 50 60HZ RATED POWER W 260W AMBIENT TEMPERATURE 41 100 F TEMPERATURE RANGE 32 50 F NET WEIGHT 231 5 Lbs 105 Kgs GROSS WEIGHT 275 6 Lbs 125 Kgs DIMENSION 59 1 W 30 0 D x 31 5 H 1500W x760D x800H mm www kingsbottle com 14 www kingsbottle com 15 PART IX WARRANTY INFORMATION Please speak to your Retailer before calling BTO AMERICA LIMITED also known as KingsBottle if you did not purchase your Beverage Cooler
11. lugged into its own dedicated 110 115V 50 60Hz AC electrical outlet 2 The plug must be accessible when the cooler is in position www kingsbottle com 3 essential the power point is properly earthed to ground Consult a qualified electrician if you are unsure 4 Don t use extension cords or adapter plugs with this cooler 5 the power cord is damaged have it replaced by a qualified service technician 6 Unplug the cooler before cleaning it or changing the light bulb to avoid electric shock 7 Never unplug the cooler by pulling the electrical cord as this may damage it Grip the plug firmly and pull straight out 8 Choose a location for your cooler that isn t too cold The ambient room temperature should be above 50 F 9 Stand your cooler in a dry place avoid areas of high moisture or humidity 10 Don t put the cooler in frosty or unprotected areas like a garage or on the verandah 11 Keep the cooler out of direct sunlight 12 Don t locate the cooler near stoves fires or heaters 18 When installed correctly your cooler should e Have adequate space at the back and sides for air circulation e Be aligned to the surrounding cupboards e Have doors that will self close from a partially open position 14 Please inspect and clean the filter in front venting grill every month Failure to clean will void the warranty and increase the running costs BEFORE USING YOUR BEVERAGE COOLER 1
12. or does not operate 2 Yellow Indicator Light is broken or poorly connected replace the indicator light if it is broken Low voltage Check power supply and install power regulator if necessary The compressor is out of work Thermal controller or timer are not turned to the work position Check thermal control or timer knob turn to work position Poor contact of thermal controller of timer Check inserting components and make sure they are well connected Thermal controller for timer fail to work Check thermal controller or timer replace it if it is faulty The compressor is damaged or its starter or capacitor is damaged Check the starter or capacitor replace it if it is faulty Loose contacting point of circuit Check and make it well connected The compressor does not turn off The temperature in the cabinet is too high due to any of the following reasons 1 The door opens too frequently 2 Ambient temperature is too high 3 Leak or lack of refrigerant 4 Timer is damaged 5 Too much grease for condenser or condenser filter Improve the air ventilation or adjust the location of knob Check leaking and refill refrigerant in terms of regulation Replace the timer Compressor start and stop frequently The door gasket does not seal properly Use hair dryer to blow hot air and make the door seal smooth The condenser fan or evaporator fan failed Replace the faulty fan T
13. re In general once unit has settled it will keep products within 5 F 2 C of the set temp easily in temperatures up to and beyond 100 F 38 C O CAUTION 1 In the event of a power interruption all previous temperature settings will be automatically saved and each compartment will return to the previous temperature setting 2 Ifthe unit is unplugged loses power or is turned off you must wait over 6 minutes before restarting Within this 6 minutes compressor protect itself and will not start even power ON again 3 When you use the Beverage Cooler for the first time or restart the Beverage Cooler after having been shut off for a long time there will be a few degrees variance between the temperature you select and the one indicated on the LED readout for the first few hours of operation After a few hours of operation the temperature will normalize to the displayed temperature www kingsbottle com 10 PART V LAYOUT AND STORAGE YOUR CABINET WAS DESIGNED TO STORE A MAXIMUM NUMBER OF BOTTLES SECURELY WE RECOMMEND THAT YOU OBSERVE THE TIPS BELOW TO OPTIMIZE LOADING 1 Disperse your bottles even so as not to concentrate weight in any one area Also be careful that your bottles do not touch either the back of the cabinet or the step at the bottom 2 Also make sure that bottles are not all grouped together either at the top or bottom of the cabinet A cooler that is full and has nice allowance for air movement will work more
14. such as thin board vinyl floor tiles or laminate You may now need to fine tune the installation by repeating steps 2 3 and 4 Wipe off any dust that has accumulated during shipping and clean following the directions in Part VIII Care amp Maintenance Plug the appliance into the power point Don t use a double adaptor or extension cord is recommended that you let the appliance for an hour or two before you put any wine in it This will confirm that it is operating correctly and make the conditions appropriate for wine storage Congratulations You have successfully installed your cooler refrigerator freezer www kingsbottle com 6 PART IV OPERATING YOUR BEVERAGE COOLER This KingsBottle Refrigerator series comes with Digital Temperature Controller Model SF 912A Before using your Refrigerator please read these instructions carefully Cold room Sensor 208017 Evap Sensor Connect main LA v Door switch test control board DIGITAL TEMPERATURE CONTROLLER MODEL SF 912A 1 Set temperature adjustment 1 1 Press UP or DOWN button the temperature is displayed 1 2 Press UP or DOWN button to modify and store the displayed value 1 8 Press SET LIGHT button to exit the temperature adjustment and display the room temperature 1 4 If no more button is pressed within 6 seconds the cold room temperature will be displayed Set temperature adjustment parameter E1
15. th a blanket or similar item Qu Te co Nec ENERGY SAVING TIPS 1 The Beverage Cooler should be located in the coolest area of the room away from heat producing appliances and away from direct sunlight Ventilation at rear also helps a lot with energy usage so create a positive air flow where possible although with this range they are designed to be fully built in 2 When you are not using fridge during weekdays etc it is recommended to set the temp at a higher level so set at 47 F 8 C during periods of non usage this will not only mean less run time it also still keeps drinks at a temp that won t be spoiled It saves energy also which these days is a growing concern for most households 3 Keep the cooler stocked an empty cooler will run longer believe it or not www kingsbottle com 12 PART VII PROBLEM Green Indicator Light does not operate TROUBLESHOOTING GUIDE POSSIBLE CAUSE 1 If the compressor working the possible cause is green indicator light bad connection or broken 2 compressor does not work the possible case is thermal controller or timer faulty Solution Check and make sure the light is well connected or replace the indicator light if it is broken Check repair replace the thermal controller or timer Yellow Indicator Light 1 The electricity plug is damaged or poorly connected to the socket Check and make sure the light electricity plug is well connected to the socket
16. xtended warranty plan we recommend you contact a third party warranty provider However regardless of point of purchase all KingsBottle coolers are backed by a ONE YEAR manufacturer s warranty from date of sale COMPRESSOR BEVERAGE COOLER www kingsbottle com 16
Download Pdf Manuals
Related Search