Ghost Use Guide - the UAV Hobby Shop!
Contents
1. Ascend Descend Ready to take off control GHOST s height Takeoff GHOST ascends to flight starting point White dotted line flight path 10m above takeoff point and hover Blue line assigned route Red line distance between eee i E ERE Ai takeoff point and GHOST o a a i Yellow line distance between and smartphone and GHOST GHOST descends to ground Follow Note The map above is for indicative purpose only The actual map may differ GHOST automatically follows the user eon nee BU wien noes minimum horizontal distance required 3m 24 Unlock Unlocked op gt 9 gt Unlock Propellers spin Voice notice Tap Takeoff at low T indicates to fly GHOST e GHOST will beep if flight command is not received in three minutes and thirty seconds This is a normal notice You can tap TAKEOFF or unplug the battery to extinguish this notice AAfter tapping LOCK a prompt will oop up and confirm again if you want to lock your GHOST Please note that GHOST s propellers will stop spinning after LOCK Q 10m y Ascend to 10m AC E destination spot height and hover L gt D updated destination spot Note the point to point command can be executed only when the height is 10m or higher Takeoff point Only if satellite number is gt 6 GHOST can take off normally Only if user s smart phone connects to Internet the APP interface will display the positions of user2. Balancing and stabilization angle roll angle 45 Angle of pitch 90 to 30 Supported types of Camera EHANG Camera Gopros Gopro3 and Gopro4 12 Note While you attach Gopro 4 on the GHOST gimbal please affix this iron clump on the gimbal to avoid shaking How to use the iron clump Pull off the adhesive paper on the iron clump Affix the iron clump on the gimbal s electrode as shown in illustration Iron Clump Gimbal Installation Camera Assembly Fix the Camera ring to the Camera with the long 1 5 screws Then connect the Camera with the lower base of the gimbal with the short 1 5 screws Note installed parts need to be tightened with the screwdriver gt In Gimbal Lower base of gimbal Camera CY rt A Completion Camera guard Long 1 5 screws 1 5 screws install the upper base of Gimbal Fix the Camera guard to the Camera by using the long 1 5 screws Then connect the Camera with the lower base of the gimbal by using the short 1 5 screws Note installed parts need to be reinforced by using the screwdriver 13 Upper base of gimbal Absorber Wi Short 2 0 screw Completion Diagram Connect the upper and lower gimbal base Connect the upper and lower gimbal base with 4 absorbers completion Wiring Important e Method Open the front and rear covers of GHOST and cut off the tie binding the plug be careful not to cut the cable Take the red and blac
3. Binding This feature can solve the problem of connection failure with a new G BOX Method open the APP and turn on the G BOX the first DATA indicator flickers in blue to make Bluetooth connection you must not electrify the GHOST at this time After Bluetooth connection is established the first DATA indicator is solid on click Setting Other Settings Binding The system shows that it is binding Please connect the battery to electrify GHOST And successful binding will be shown in 2 seconds If the system still shows that it is binding 5s later it is recommended to perform operations above once again e Map This feature is for selecting the type of flight map Click the corresponding map to switch CEI ce PROJ About EHANG e You can view the current App version and introduction of EHANG eurom SETTINGS Cooyright 214 2014 Ehang All Hight Rese vod OTHER GHONI 1 0 1 23 GHOST App Interface Instruction A 72 Distwe Om Heightiim Speedc km h Time amp min Setting Flight Mode Satellite Number Hover Battery Level Distance Height GHOST remains at the same spot in Horizontal Speed Flight Time the air Gimbal vee right left tilt Micro eu make slight adjustment to GHOST in Gimbal hovering status similar to joystick up down tilt Rotate Lock Unlock control GHOST s directions in the air Lock Propellers stop Unlock Propellers spin at low speed
4. Windows XP VistaorAbove win Mac os 59 27 41 13 29 28 LCD screen LOLiPs Lens 170 DEG Grade A high resolution wide angle lens Simplified Chinese Traditional Chinese English German French Language guag Spanish Italian Portuguese Russian Japanese 1080P 1920 1080 SOFPS 720P 1280 720 6OFPS VGA 848 480 60FPS QVGA 640 480 6OFPS video format MOV Recorded video video signal compression format H 264 picture resolution 12M 8M 5M storage card Micro SD picture mode single shot timed self portrait 2s 5s 10s continuous shooting light Source frequency 50Hz 60Hz USB USB2 0 power supply BVIA Power Capacity 900mAh Power consumption 400MA 4 2V Video recording duration 1080P 7 0min Charging time about 3h cy Parameters may be upgraded or changed Specifications and parameters might defer contingent upon real product 18 GHOST App GHOST App is a smartohone operating system specially developed for the GHOST quadcopter You can fly GHOST on your own through performing operations with GHOST App without use of RC transmitter All functions of the RC transmitter joysticks are simplified as one click command which simplifies flight and delivers a smoother flignt experience to you GHOST App Download You can download through following methods Note The GHOST App supported devices and operating systems includes Android smart phones running Android 3 0 or
5. GHOSI DRONE CREATED BY EHANG IN G ADVANCED MANUAL www ehang com Cautions Reading Tips e Symbol Designation e Usage Suggestions e Watching Tutorial Videos About Flight e Flight Environment e Pre flight Examination About GHOST e Introduction e Parts List Preparations e Battery e G BOX e GHOST e Propeller e Prop Guard GHOST App e GHOST App Instructions Arer sales Services CONTENTS e Flight Safety e Cautions during Flight e Gimbal e Landing Gear e Camera e GHOST App 01 02 03 04 JS 06 19 20 28 Ad pleiancsicetence Please refer to relevant regulations of the International Civil Aviation Organization local airsoace control and UAV management rules Otherwise it may incur liabilities for violation of laws or regulations Once this product is used it will be assumed that the user has knowledge and accepted all the contents of this statement User will be held accountable for their actions or any direct or indirect consequences caused by incompliance with the aviation restrictions of this manual Black Box Each GHOST drone is equipped with a black box which records flight information and working parameters of the motor which are used for flying tests and accidence analysis Operation Please operate the GHOST carefully This product contains sensitive electronic components which might be damaged if GHOST is dropt broken or exposed in A oo D
6. Hos PAN i Aerial PI If you select a drone type with the symbol the system will display This setting is not available Click OK to select again P olecter No Protecter O Gir nihal Nn Girbal Do uble Three bladed bladed SOUT Not available 21 INTRODUCTION TO APP SETTINGS App Bluetooth Pairing You can view the existing paired Bluetooth device search for new devices rename and remove a device e View Bluetooth Devices Click the Setting button at the upper left corner to enter the Setting interface and view the connected Bluetooth device gt uric C MATCHED DEVICE semos UINE S50JT e Search for Bluetooth Devices Click the Search button at the bottom right corner to search for new devices When a new Bluetooth device is found directly click the corresponding device to connect it gt ESEA GA MATCHED DEVICE D SETTINGS EHANG LAV Ei hierar Get the name af the cevice 08 03 31 3000 OTHER 08 03 51 50 00 66 Get the name afike gwicr ga L33 105 08 F1 e ASOT Rename Bluetooth Device Rename the Bluetooth device by clicking the Edit buttonL on the right side Enter the new name and then click OK gt Gaia C MATCHED DEVICE G uncs gt PHANG uav la 6 F eee enter the mame of the GHOST mang usy iia EHAMG UAY Quon 22 Drone Type Settings This feature is used for selecting the GHOST configurations Other Settings e
7. N Modhicatonm C omona If you need to modify GHOST or mount other devices on GHOST please consult our customer service in advance EHANG is not accountable for damages or loss caused by unsupervised modification or mounting on GHOST Maintenance Please do not disassemble or repair GHOST on your own which may cause prod uct damages or personal injuries If GHOST is damaged malfunctioned or exposed to liquid please contact EHANG or authorized distributors Battery Please do not disassemble squeeze strike burn drop or step on the battery Do not short circuit or touch the battery interface with metallic objects Do not expose the battery in the environment with a temperature higher than 60 C Please charge the battery with our original charger Please store the battery in a dry environment out of children s reach Storage Environment If GHOST and its parts are to be left idle for a while please take out the battery and store it In a dry environment free from dampness molds and exposure to sun and electromagnetic interference EMI 01 READING TIPS S A O Prohibited Operations Cautions Operation Instructions Usage Suggestions EHANG provides the GHOST users with tutorial videos and manuals to ensure you can experience a more joyful flight 1 Tutorial Videos Website www ehang com 2 Disclaimer Website www ehang com 3 Quick start Manual help users to have a quick start 4 GHOS I User Manua
8. above iPhone 5 smartohones running iOS 7 0 or above and iPad 3 running iOS 7 0 or above Visit www ehang com to download EHANG GHOST App O gt Qa www ehang com Lx gt Download the App by scanning the QR code ay L NY Download the App from Google Play GHOST APP INSTRUCTIONS App Interface Start the App on your smartphone Enter the welcome interface n IAA y g E IO IAIO ONUS The system automatically searches for devices and automatically enables the Bluetooth feature and connects the Bluetooth device you need to turn on the G BOX Oe ona be ev EHANG UA GROSS 1S ee Note the following interfaces will appear after when you log onto the App for the first time Then enter sd OPEN AREA ONE TAP ROUTING URLO Move TLS RIGHT AAY raana 20 Drone lype Settings e After successful Bluetooth pairing the drone type settings window will automati cally pop up Please make the settings for your actual GHOST version After click ing OK the system will show the setting of GHOST parameters is completed and then enter the App operation interface automatically e f you need to reset click the Setting button at the upper left corner to modify the drone type settings on Fe L Protecter No Protecter aoe Ej aimbal F No Gimbal wae as T b lee i a ANP E 5 Dou hi s hlad bladed AHCI I i
9. and GHOST on the GPS map e As the picture shows A is GHOST s spot Click any destination B on the map to direct GHOST If the destination is updated in midway GHOST will fly from current spot C to the updated destination D Hover Hover e Hover GHOST remains the current spot in the air e TAPPing Hover in any status will terminate the previous command and keep GHOST hovering e Estimate the height of barriers to avoid collision 20 Auto Follow A to B distance is the horizontally projected distance A Please fly GHOST in an open area GHOST does not have the obstacle avoiding function A While climbing please adjust GHOST s height accordingly GHOST cannot automatical ly adjust its height e Available only in HOVERING status the premise is that GPS on smartphone is activated e At minimum 3m horizontally projected distance from the smartohone holder with the G BOX GHOST begins to follow the user automatically The farther apart e GHOST is from the user the faster GHOST flies maximum speed 18km h e Io stop user should lower his her pace gradually Do not stop immediately or GHOST will fly over the user due to high speed e Jo terminate auto following tap any available button on interface e t is recommended that the GHOST height should be higher than the user s Height gt 15m GHOST directly returns QHeight lt 15m GHOST ascends to 15m and retums 15M 10m N
10. button to switch the camera Video Recording Replay Functional modes The mode signs are displayed on the top of the screen i Video Recording Picture Capture and Video Replay modes and Functional List setting are shown in order Setting and Use of Camera Video Recording and Video Setting When the camera is on the video record ing mode and a symbol Bis shown in the upper left corner of the screen press OK to start video recording and the symbol Starts flickering at the upper left corner of the screen Then pressing OK stops video recording and at the same time the e symbol disappears in the upper left corner of the screen e Picture Capturing and Picture Capturing Setting Turn on the power and select the Picture Capture mode When a symbol is shown at the upper left corner of the screen the camera enters the picture capture mode Press OK to take pictures Picture taking mode single shot timed self potrait 2s 5s 10s continuous shooting e File Storage and Playing After video recording is completed copy video files generated onto a computer by using a USB drive Also you can take the Micro SD card out and read video data on the card by using a card reader O Note when the camera operates poorly and a dead halt occurs you can remove gt the battery and re install it and then the Camera can return to normal le Technical Parameters of Camera a Item Parameter Operating system
11. ck Note during installation please press the propeller with your left hand tighten the nut with your right hand and fasten the nut with a screwdriver follow similar technics to dissemble propellers i l a os12R Upside down Before After Completion Caution for Propellers e Before each flight check whether propellers are installed correctly and securely e Before each flight please check whether each propeller is in good condition Replace any damaged and aged propeller timely e Please do not approach the spinning propellers to avoid personal hurt e Please use EHANG proprietary three blade reversible propellers to ensure optimal flight effect 11 OD Uo GHOST prop guards are made from intensified compound material They are lighter and more appropriate for flight and also can protect blades from damages caused by external collision Assembly and Disassembly of Prop guards Assembly place the prop guards to the fixed position of GHOST and fasten three 2 0 screws with the screwdriver Disassembly screw off the three 2 0 screws fixed the prop guards with the screw driver and remove the prop guards Assembly Completion Diagram GHOST proprietary gimbal is made from aluminum alloy material and used for carry ing the Camera Technical Parameters of Gimbal l Scan to watch the tutorial Weight 178g video for installation of gimbal Accuracy 0 09 and landing gear Operating voltage 7V to 17V
12. e unlocked and takeoff Red LED indicator flickering 1 Before takeoff initial status 2 During flight battery level is low Red LED indicator solid on 1 GHOST is unlocked 2 During flight Red LED indicator Blue LED indicator 09 Propellers Scan to watch the tutorial Propel lers Introduction video for propellers installation GHOST is equipped with 8 inch three blade reversible propellers Propellers are consumable parts You can visit EHANG s official website to buy propellers if needed Propellers Installation Prepare GHOST parts Prepare all the parts and tools Note grey part indicates the backsides of GHOST and parts AA Aa A GHOST drone Right propeller 2 cushion 4 Nut 4 Screwdriver Left propeller 2 Identify the front and back ends of propellers R indicates right propeller L indicates left propeller The character can be found on the propeller s rim on the front end No character on the back of the propellers Left Right Back front Back front Assemble Propellers Pick the cushion in the red circle and fit it in the small holes on the backside of propellers respectively Before Atter Install Propellers Put GHOST upside down The propeller should be placed on the motor with propellers front ends with character facing downwards L propeller should be Installed to the R motor R propeller should be installed to the L motor Fasten the nuts at the ba
13. gram Indicator OK button ON OFF button 9 16 Mode button HD lens Attery cover lock button Screen UP button Speaker Down button Operation Indicator Charge Indicator 16 Use and Operation of Camera Insert the Micro SD card Note please use quality Micro SD card Format it to the exFAT32k format on your computer before use Ordinary neutral cards cannot be used normally Placement and Removal of Battery e You can open the battery cover by push ing it down e Put the battery correctly into the camera following the plus and minus symbol and arrow direction indicated on the battery You can remove the battery by pushing the battery cover out Battery Charging Battery can be charged by either connect ing it to a computer or with a power adapt er e Battery can be charged with a car charger e Video recording while charging turn on the Car Mode in the functional list setting Battery can be charged when camera is off e The charging current needs to be less than 1000mA otherwise the battery will be damaged Power on and Power off of Camera You can power on or off the camera by pressing the ON OFF button on the front of the camera press power button to turn on the camera Long press the power button GOODBYE display on the screen and camera is turned off Mode Switching mode After camera iS powered on short press the ON OFF
14. ial Plus GHOST G BOX G BOX cable Battery Battery charger Battery Cable 2 Gimbal Camera including 16G SD card Landing gears Screwdriver 8 screws GHOST Aerial Compared to GHOST Aerial Plus GHOST Aerial is without the camera Note are components of GHOST Aerial Plus 05 PREPARATIONS uN To use GHOST Aerial Plus users need to install the landing gears gimbal and camera and dissemble the prop guards We recommend that GHOST Aerial Plus users practice flying GHOST Basic without camera first And then assem ble and operate GHOST Aerial Plus after you can skillfully operate GHOST Before using GHOST please ensure that the battery and G BOX have sufficient Dower Battery Introduction GHOST s battery is a 5400mAhN 11 1V lithium polymer battery with XT60 connector and charge discharge function It must be charged with an EHANG proprietary charger Battery Charger Battery Charging e Make sure the wiring of the battery is correct Battery Charging Schematic Diagram Side view of battery charger Insert the charger into the 3S interface e When battery is being normally charged 15 2S and 35 indicator lights are on and 48S indicator light is off e Battery Type LiPo e Charge status indicating that the battery is being charged indicating that the battery is fully charged 1A 2A BA charge current value Battery charging nor
15. k i the backward e Micro control enables accurate landing 2 AFTER SALES SERVICES After sales Services All GHOST products are supported with after sales services If you encounter any problems please e mail Ssupport ehang com To learn more about software update campaigns product develooment and after sales services please visit our official website www ehang com 20 FHANG EHANG INC WEBSITE www ehang com FACEBOOK theghostdrone TWITTER GhostDrone INSTAGRAM GhostDrone
16. k plugs out from the rear cover A You must ensure that the plug must be inserted into the correct slots with the right colors otherwise the gimbal will be blown out GHOST bottom GHOST Gimbal Back Gimbal Completion Landing Gears EHANG proprietary landing gears are made from intensified compound material It can support GHOST and protect the gimbal and camera Landing Gears Assembly Landing gears should be installed for GHOST Aerial Aerial Plus During assembly make sure the installation orientation of the landing gear cross bar is right The method for assembly of two landing gears is as shown in the figure below Landing gear base Landing gear head Landing gear cross Landing gear assembly Landing gear head gg N mlm ANN mO rslaalsigs EHANG Camera not only has an ultra mini appearance but also can shoot 1080P HD video Product Features e Shooting Features e The ultra high definition display screen can display and replay wondertul videos e The battery is detachable and this increases the ease of replacement and extends the battery life e Video recording while charging e Video recording with mains connected e 12 million pixels HD wide angle lens e HDMI HD output function e Up to 32G SD card e 1080P 720P WVGA e Video recording in the MOV format e Multiple shooting modes single shot automatic continuous shooting e Video mode locking e Ultra mini aopearance Camera schematic dia
17. l provides detailed instructions for use Watching Tutorial Videos Official GHOST tutorial video Please watch the tutorial video on www ehang com to intuitively learn how to use the GHOST correctly and safely Video Collections of GHOST Video of GHOST Aerial Assembly Assembly 02 ABOUT FLIGHT e GHOST might encounter errors due to interferences in the environment with dense or high buildings Please fly GHOST in open area to reduce drift error e Please fly GHOST away from obstacles crowds high tension lines trees water Surface etc e Please do not fly GHOST in the restricted airspace by relevant laws or regulations e Please fly GHOST away from places with complex electromagnetic environment e Please fly GHOST over 200m away from signal towers base stations etc where Interference exists to avoid takeoff failure or crash caused by strong EMI e Please do not fly GHOST under high temperature or in extreme weather including heavy rain snow or strong wind stronger than Class 5 and heavy fog Pre flight Examination Check whether the G box and battery have sufficient power e Whether propellers are correctly installed and secured e Whether motors can be normally started up after being unlocked Flight Safety e Make sure that there is a minimum of 5m distance between you and GHOST e Please stay away from dangerous obstacles such as barriers crowds and high tension lines During the flight keeo GHOST
18. mally a bigger value indicates a faster charging speed You can Schematic diagram of control select a charge current value panel of battery charger 06 Battery Installation Place GHOST on the horizontal ground and connect the battery wire When flicker ing frequency decreases approximately 5s push the battery into the battery compart ment in the correct direction Close the compartment door and make sure that the battery is tightly retained in the battery compartment please perform these operations in an open area A If the battery is not tightly retained this will lead to poor contact or failure to acquire battery Information which will affect flignt safety and even lead to takeoff failure Caution for Use A e You must charge the battery with the EHANG proprietary charger e You must make sure that the battery is free from damage deformation bulging el Used battery should be cooled down to room temperature before charging again e It is strictly prohibited to charge the battery on a combustible object or without attending e Please do not store or charge the battery in the sunlight e Do not charge the battery for more than 3 hours e Improper use of the battery may lead to fire explode or other dangers e It is strictly prohibited to disassemble or modify the battery circuit or penetrate the battery e Ihe voltage must be maintained between 11 4V and 11 6V voltage of a single battery cell should be mai
19. ntained between 3 8V and 3 85V e You must keep the battery far away from children water Sources and fire Sources 07 G BOX Introduction G BOX is a communication device to transmit signals to GHOST Each GHOST is equipped with a G BOx Please store it properly because you will be unable to oper ate GHOST through your smartphone without G BOX Charge cable Communication ON OFF G BOX USB charging cable Charge Power indicator indicatorinterface Charging and Use of G BOX Power on press the ON OFF button Power off press and hold the ON OFF button until PWR indicator turns off Charging four indicators flicker in order Fully Charged the indicator at the far left flickers and three indicators on the right are constantly on After G BOX is fully charged turn on smartphone Bluetooth to connect the smart phone APP with G BOX 08 GHOST Introduction The GHOST quadcopter has a built in flight controller which enables users to direct ly and easily control through the smartphone App to execute the commands of forward backward leftward rghtward ascend descend rotate and point to point flying and make GHOST fly stably Description of LED Indicators There are two colors of LED indicators red ones indicate forward and blue ones indicate backward Blue LED indicators flickering GHOST is searching for GPS satellites Blue LED indicators solid on more than 6 satellites are found and GHOST can b
20. ote wo situations of return GHOST s height is over 15m above takeoff point GHOST s height is less than 15m above takeoff point e In either situation GHOST adjusts its height to 15m automatically and descends to 10m s height and hovers e Heights in the figure are all calculated based on the horizontal plane of the takeoff point as reference A The flight path is a straight line Please ensure that no obstacle in the flight path 26 Ascend Descend Rotate GHOST rotates C3 PU Orana ann e Pull rightward gt GHOST rotates Rotate clockwise O Can Pull upward gt GHOST ascends QY Pull downward gt GHOST descends Ascend Descend Note During flight the height control bar is hidden on right side of the APP Interface Height control is only accessible in hovering status Gimbal Operations Pull leftward gt Gimbal tilts left G Pull rohtward Ww ghtward gt Gimbal tilts right Pull upward Gimbal tilts upward i ri EY Pull downward gt Gimbal tilts downward e GHOST automatically lands On the ground slowly GHOST locks automatically five seconds after landing e Micro control is available only after you tap the Hover button e Micro control is available only after you tap the So to vA the Hover button Lae e LA e Micro control enables GHOST to move ee E horizontally on the current horizontal plane of the current height ee Red lights marks the forward blue lights mar
21. within your sight to avoid accidents caused by oversight of the Surroundings Landing gears and prop guards can not be installed in GHOST at the same time e Children must be accompanied by experienced flyers when operating GHOST 03 Caution During Flight e User is recommended to hold the G BOX in hands or put It in the pocket Other wise It will lose Communication beyond the limited distance Smartohone Pocket G BOX e Height control is only accessible in hovering status During flight the height control bar is hidden on the right side of the APP interface It is normal for the battery level to rise again after landing It is not advisable to launch your GHOST when battery level is less than 30 It is best to fly GHOST with a fully charged battery Please tap HOVER immediately in times of emergency If GHOST fails to hover please ensure your own safety before attending to GHOST Do not be afraid to damage GHOST 04 ABOUT GHOST Doda HoN GHOST is the first quadcopter completely controlled by a smartphone App in China With an advanced flight control system and a smart mobile device GHOST App can realize the functions including point to point flying out of sight flying auto follow mode and tilt mode Simple operations on a smartohone enable every one can fly a drone to experience the joy of flight GHOST Basic GHOST G BOX G BOX cable Battery Battery charger Battery Cable 2 GHOST Aer
Download Pdf Manuals
Related Search