LED Followspot 75ST User Manual Rev. 6
Contents
1. Make sure the power cord is not crimped or damaged Never disconnect this product from power cord by pulling or tugging on the cord If mounting this product overhead always secure it to a fastening device using a safety cable Make sure there are no flammable materials close to the unit while operating Do not touch this product s housing when operating because it may be very hot Always make sure that the voltage of the outlet to which you are connecting this product is within the range stated on the specifications sticker or rear panel of the product This product is for indoor use only IP20 To prevent risk of fire or shock do not expose this product to rain or moisture Always install this product in a location with adequate ventilation at least 20 in 50 cm from adjacent surfaces Be sure that no ventilation slots on the unit s housing are blocked Never connect this product to a dimmer Make sure to replace the fuse with another of the same type and rating Never carry this product from the power cord or any moving part Always use the hanging mounting bracket or the handle The maximum ambient temperature Ta is 104 F 40 C Do not operate this product at higher temperatures In the event of a serious operating problem stop using the unit immediately Never try to repair this product Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assist2. lt BLUE gt Projects blue color lt WHITE gt Projects white light lt FUNCTION SELECTS Selects Manual or DMX Mode lt UP gt In DMX Mode moves channel number up lt DOWN gt In DMX Mode moves channel number down Menu Map Mode Programming Steps Description Manual Mode NAn Selects Manual mode DMX Address 001 001 512 Selects the DMX starting address Gobo To access the gobo holder follow the steps below Replacement EN 1 Unscrew the Iris Adjustment knob 2 Unscrew the thumbscrew 3 Remove the plastic cover 4 Remove the gobo holder inside 5 Change the gobo 6 Replace everything in reverse order to use your chosen gobo Iris Adjustment Knob Thumb Screw Plastic Cover LED Followspot 75ST User Manual Rev 6 Page 9 of 14 Configuration DMX Starting Address Set this product in DMX mode to control it with a DMX controller 1 Connect this product to a suitable power outlet 2 Turn this product on 3 Connect aDMX cable from the DMX output of the DMX controller to the DMX input socket of this product When selecting a starting DMX address always consider the number of DMX channels the selected DMX mode uses If you choose a starting address that is too high you could restrict the access to some of the product s channels The LED Followspot 75ST uses up to 3 DMX channels in its 3 channel DMX personality which defines the highest configurable address to 510 For more information about DMX download the CH
3. Only loosen or tighten the bracket knobs using your bare hands Using tools could damage the knobs Bracket Adjustment Knob Surface gt Mounting Mounting Diagram AY 5 Mounting Bracket Mounting Clamp AS A such as CLP 15 or CLP 15N clamp x _ E from CHAUVET i Safety Cable WO Pe such as CH 05 from f CHAUVET KY CN see Alternative Truss Mounting using the truss mounting be sure to continuously check and secure the rigging i The alternative truss mounting is recommended for static installation only While points especially if repositioning the LED Followspot 75ST Page 8 of 14 LED Followspot 75ST User Manual Rev 6 4 OPERATION Control Panel To access the control panel functions use the buttons located underneath the display Please refer to the Product Overview to see the buttons location on the control panel Operation Button Function lt POWER SWITCH gt Turns power on and off lt DIMMER MAX gt Opens dimmer to a maximum of 100 hold to raise percentage lt DIMMER MIN gt Closes dimmer to a minimum of 0 hold to lower percentage lt SHUTTER ON gt Turns LED on default setting lt BLACK OUT gt Turns LED off lt ORANGE gt Projects orange color lt CYAN gt Projects cyan color lt RED gt Projects red color lt GREEN gt Projects green color lt MAGENTA gt Projects magenta color lt YELLOW gt Projects yellow color
4. solution ammonia free glass cleaner or isopropyl alcohol Apply the solution directly to a soft lint free cotton cloth or a lens cleaning tissue Softly drag any dirt or grime to the outside of the lens surface Gently polish the lens surfaces until they are free of haze and lint O Always dry the lens surfaces carefully after cleaning them Do not spin the cooling fans while blowing compressed air into them Page 12 of 14 LED Followspot 75ST User Manual Rev 6 Technical Specifications Dimensions and Length Width Height Weight Weight 22 in 560 mm 10 8 in 276 mm 11 5 in 292 mm 13 3 Ib 6 kg Note Dimensions in inches rounded to the nearest decimal digit Power Power Supply Type Range Voltage Selection Switching external 120 230 VAC 50 60 Hz Switchable Parameter 120V 60Hz 230V 50Hz Consumption 215W 220 W Operating 1 8A 1A Fuse F2A 250 V F2A 250 V Power I O US Canada UK Worldwide Power input connector IEC IEC Power Cord plug Edison US Local plug Light Source Type Power Lifespan LED 75 W 50 000 hours Color Quantity Current White 1 18A Photo Optic Parameter Narrow Lenses Illuminance 2 m 14 8 140 lux Illuminance 2 m 20 4 650 lux Strobe rate 0 16 Hz Iris min 5 at tightest zoom Zoom angle 14 to 20 23 7 mm outside Gobo size 21 3 mm image 1 mm max thickness Thermal Maximum External Temp Cooling System 104 F 40 C Fan assisted DMX 1 0 Connectors Connector Type Channel Range 3 pin
5. AUVET DMX Primer from the CHAUVET website http www chauvetlighting com download To select the starting address do the following 1 Press lt FUNCTION SELECT gt until 001 shows on the display 2 Press lt UP gt or lt DOWN gt to select the desired starting address DMX Channel Assignments and Values Page 10 of 14 3 CH Channel Function Value Setting 1 Dimmer 000 255 0 100 000 031 White 032 063 Dark blue 064 095 Yellow 096 127 Purple 128 159 Green 160 191 Red 192 223 Light blue 224 255 Orange 2 Color 000 003 No function 004 007 Open 008 215 Strobe slow to fast 216 255 Open 3 Strobe LED Followspot 75ST User Manual Rev 6 Set this product in one of the standalone modes to control it without aDMX controller 1 Connect this product to a suitable power outlet 2 Turn this product on Configuration Standalone Never connect a product that is operating in any standalone mode to a DMX string O connected to a DMX controller This is because products in standalone mode may transmit signals that could interfere with the DMX signals from the controller To control the product in standalone mode press lt FUNCTION SELECT gt until the Control Panel displays NAn Then simply use the button menu on the back of the product Each button serves a different function as detailed below Button Menu Dimmer A
6. LED FOLLOWSPOT T55T User Manual TABLE OF CONTENTS 1 Before YOU Begins iu se oda 3 Whats nGluded creche ved Hessens era ten u irre ner 3 Unpacking IMStruCtiOns sisi taaan sveanioeed eects 3 Claims Bean Gas aaa oc a Seen tee RER ees a ea Fe ese Ae E 3 Text CONVENTIONS dorsos ehe el a Ed naar Fangen 3 SYMBOLS bit ll lata da tada iia 3 DisclalM A ctra this 3 Producer ara GNC ias rr sia 4 A O O 4 2 Introduction ee TT can 5 Produc OvervieW aan en dada Ai id ii adi ceus astdentuar ii 5 PrOUCLDIMENSION Scsi NER IH Und Laia IA rain aid cad 6 PPP eo PE one ee EEE eS are eer ee eer 7 AG POWE A RER Rn nee ee dd 7 Fuse Replacement 2 2ek ee its 7 MOUNT a EE TEETE T ETLE ETE PEENE ETTE IE EAT LA sakes Sbigtie eves ene ares 8 OrENTatlOn 2 ie ee ee E E E E E ee EE 8 PRIQQUIAG EE EAA EEEE A E A A A A E 8 MOP a PEE EE Eee TT 9 Control Panel Operator eai a aai a A E OEE E AAE RT a 9 Menus Map enmena Aa A E T E E O NE 9 Gobo Replacement nasan na a a a a a aAa a EE EEA rado a is 9 Contiguration DMX ENREROEEFRPETTEEREERATEREERTFEEFULSPEERFERETTEFSETERCLTFERTLTERSETRTELETRELFTELEETETTESERSTFELFETSCFEEFESSELEFFERTEEFSRR 10 SLAMING Address i255 225054 hen T E E EET 10 DMX Channel Assignments and Values c ccccceeceeeeceeeeeceaeeeeaaeeeeneeceeeeesaaeeesaaeseeeeeseaeeesaaeeesaaeeenees 10 A ER ee ree eee eee 10 Configuration Sanda iia arado cana 11 BUTTON MOM oviedo geese 11 5 Technical Information anna iia
7. XLR Sockets 3 Ordering Product Name Item Code UPC Number LED Followspot 75ST 08040503 781462208554 RoHS UL 1573 CSAC22 2 No 166 Cc US E113093 zz LED Followspot 75ST User Manual Rev 6 Page 13 of 14 RETURNS U S UK Ireland and Mexico CONTACT Page 14 of 14 Us To return a product or request support In the U S contact CHAUVET World Headquarters see below In the UK or Ireland contact CHAUVETO Europe Ltd see below In Mexico contact CHAUVETO Mexico see below In any other country DO NOT contact CHAUVET Contact the distributor of record See www chauvetlighting com for a list of distributors If you live outside the U S United Kingdom Ireland or Mexico contact your distributor of record and follow their instructions on how to return CHAUVET products to them Visit our website for contact details Call the corresponding CHAUVET Technical Support office and request a Return Merchandise Authorization RMA number before shipping the product Be prepared to provide the model number serial number and a brief description of the reason for the return You must send the merchandise prepaid in its original box and with its original packing and accessories CHAUVET will not issue call tags Clearly label the package with the RMA number CHAUVET will refuse any product returned without an RMA number Write the RMA number on a properly affixed label DO NOT write the RMA number directly on the b
8. ance center Keep this User Manual for future consultation If you sell this product to another user be sure that they also receive this document LED Followspot 75ST User Manual Rev 6 2 INTRODUCTION Product Overview Control Panel Focus Lens Adjustment Knobs Bracket Adjustment Knob Button Menu Fuse holder Mounting Bracket On Off Switch Gel Frame Holder Iris Adjustment Power In DMX In Out LED Followspot 75ST User Manual Rev 6 Page 5 of 14 Product Dimensions Page 6 of 14 LED Followspot 75ST User Manual Rev 6 3 SETUP AC Power This product has a switchable power supply that can work with an input voltage of 120 VAC or 230 VAC 50 60 Hz To determine the power requirements for this product circuit breaker power outlet and wiring use the current value listed on the sticker affixed to the product s back panel or refer to the product s Technical Specifications chart The listed current rating indicates the product s average current draw under normal conditions Always connect this product to a protected circuit circuit breaker or fuse making sure that it has an appropriate electrical ground to avoid the risk of electrocution or fire Never connect this product to a rheostat variable resistor or dimmer circuit even if the rheostat or dimmer channel serves only as a 0 to 100 switch Fuse Follow the instructions below to change the fuse if necessary Replacement AN Disconnect
9. ffects brightness of the light Press and hold either lt MAX gt to brighten or lt MIN gt to darken from 0 100 T RMMER MIN ORANGE OS Shutter Turns light on and off Press lt ON gt to turn on and lt BLACK OUT gt to turn off ea BLACK OUT HOLD FOR 3 SECONDS TO STROBE Control Panel When NAn is displayed it is in Manual M ode When 001 is displayed it is in DMX Mode CONTROL PANEL FUNCTION SELECT DMX MODE MANUAL MODE Color M enu Function Select Up Down Changes color of LED light output Choose Toggles between Manual In DMX mode select color on the menu to change to desired color and DMX modes starting address LED Followspot 75ST User Manual Rev 6 Page 11 of 14 5 TECHNICAL INFORMATION Product Dust build up reduces light output performance and can cause overheating This can lead to reduction of the light source s life and or mechanical wear To maintain optimum Maintenance performance and minimize wear you should clean your lighting products at least twice a month However be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency To clean this product follow the instructions below Unplug the product from power Wait until the product is at room temperature Use a vacuum or dry compressed air and a soft brush to remove dust collected on the external surface vents Clean all lens surfaces with a mild soap
10. io 12 Product Maintenance elle A ran A ai 12 Technical SpeciiGatlons mitral lacras 13 O 14 5 cl AAA AA 14 Page 2 of 14 LED Followspot 75ST User Manual Rev 6 1 BEFORE YOU BEGIN What is LED Followspot 75ST Warranty Card Power Cord Quick Reference Guide Included Mi Unpacking Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition Instructions Claims If the box or the contents the product and included accessories appear damaged from shipping or show signs of mishandling notify the carrier immediately not CHAUVET Failure to report damage to the carrier immediately may invalidate your claim In addition keep the box and contents for inspection For other issues such as missing components or parts damage not related to shipping or concealed damage file a claim with CHAUVET within 7 days of delivery Text Convention Meaning Conventions 1 512 A range of values 50 60 A set of values of which only one can be chosen Settings A menu option not to be modified Menu gt Settings A sequence of menu options to be followed lt ENTER gt A key to be pressed on the product s control panel ON A value to be entered or selected Symbols Symbol Meaning Critical installation configuration or operation information Not following these instructions may make the product not work cause damage to the product or cause harm to the operator Impor
11. ox Before sending the product clearly write the following information on a piece of paper and place it inside the box Your name Your address Your phone number RMA number A brief description of the problem Be sure to pack the product properly FedEx packing or double boxing are recommended CHAUVETO reserves the right to use its own discretion to repair or replace returned product s CHAUVET is not responsible for shipping damage of returned items WORLD HEADQUARTERS CHAUVETO General Information Technical Support Address 5200 NW 108 Avenue Voice 954 577 4455 Press 4 Sunrise FL 33351 Fax 954 756 8015 Voice 954 577 4455 Email tech chauvetlighting com Fax 954 929 5560 Toll free 800 762 1084 World Wide Web www chauvetlighting com UNITED KINGDOM AND IRELAND CHAUVET Europe Ltd General Information Technical Support Address Unit 1C Email uktech chauvetlighting com Brookhill Road Industrial Estate World Wide Web Pinxton Nottingham UK www chauvetlighting co uk NG16 6NT Voice 44 0 1773 511115 Fax 44 0 1773 511110 MEXICO CHAUVET Mexico General Information Technical Support Address Av Santa Ana 30 Email servicio chauvet com mx Parque Industrial Lerma Lerma Mexico C P 52000 World Wide Web www chauvet com mx Voice 52 728 285 5000 Outside the U S United Kingdom Ireland or Mexico contact the dealer of record and follow their instructions to request support or to return a p
12. roduct Visit the CHAUVET website for contact information LED Followspot 75ST User Manual Rev 6
13. tant installation or configuration information The product may not function correctly if this information is not used Useful information Disclaimer The information and specifications contained in this document are subject to change without notice CHAUVET assumes no responsibility or liability for any errors or omissions that may appear in this manual CHAUVET reserves the right to update the existing document or to create a new document to correct any errors or omissions You can download the latest version of this document from www chauvetlighting com Copyright 2014 CHAUVET All rights reserved Electronically published by CHAUVET in the United States of America Author Date Editor Date A Leon 01 08 14 L Henry 01 09 14 LED Followspot 75ST User Manual Rev 6 Page 3 of 14 Product ata Glance Safety Notes Page 4 of 14 A A L Use on Dimmer Auto Programs X Outdoor Use Switchable Power Supply P Sound Activated Replaceable Fuse P X DMX User Serviceable Master Slave Please read the following Safety Notes carefully before working with this product They include important safety information about its installation usage and maintenance Always connect this product to a grounded circuit to avoid the risk of electrocution Always disconnect this product from the power source before cleaning it or replacing the fuse Avoid direct eye exposure to the light source while the product is on
14. this product from power before replacing the fuse Disconnect this product from power Using a Phillips 2 head screwdriver unscrew the fuse holder cap from the housing Remove the blown fuse Replace with a good fuse of the same type and rating Screw the fuse holder cap back in place and reconnect power Or ONS Always replace a blown fuse of the same type and rating LED Followspot 75ST User Manual Rev 6 Page 7 of 14 Mounting Before mounting this product read and follow the safety recommendations indicated in the Safety Notes section Orientation The LED Followspot 75ST may be mounted in any position however make sure adequate ventilation is provided around the product Rigging Before deciding on a location for this product always make sure that it will be easy to access the unit for maintenance and programming purposes Make sure that the structure onto which you are mounting this product can support its weight Please see the Technical Specifications section of this manual for weight information If mounting this product overhead always use a safety cable Mount the product securely to a rigging point whether an elevated platform or a truss When rigging this product onto a truss you should use a mounting clamp of appropriate weight capacity The bracket has 13 mm holes which are appropriate for this purpose The bracket adjustment knobs allow for directional adjustment when aiming the product to the desired angle
Download Pdf Manuals
Related Search