24-port 10/100/1000Mbps Layer 2 Managed Switch
Contents
1. Hardware Installation Connecting to the Console Port and Ethernet Port 1 Attach one end of the supplied RS 232 cable to PC or terminal and the other end to the console port of the SP1684B front panel The connected terminal or PC must support the terminal emulation program 2 Connect one end of an RJ 45 cable to the Ethernet port at the front panel and the other end to PC or terminal for web interface management Cabling Requirements for 1000Base SX LX SFP Module SP1684B supports the more complex and comprehensive TP cabling in the fiber media Basically there are two categories of fiber multimode and single mode The later is categorized into several classes by the distance supported They are SX LX LHX XD and ZX From the viewpoint of connector type there mainly are LC and Bi Di LC Gigabit Fiber with multimode LC SFP module Gigabit Fiber with single mode LC SFP module Gigabit Fiber with Bi Di LC 1310nm SFP module Gigabit Fiber with Bi Di LC 1550nm SFP module For more details please refer to user manual CE Mark Warning This equipment complies with the requirements relating to electromagnetic compatibility of the essential protection requirement of Council Directive 89 336 EEC on the approximation of the laws of the Member States Company has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors for the la2. nd line interface of console management appears 6 Communicate via Micro network li a Beall a He Quick Installation Guide 24 port 10 100 1000Mbps Layer 2 Managed Switch Making Communication Easier Model No SP1684B www micronet com tw Introduction Micronet SP1684B Gigabit Layer 2 Managed Switch offers Gigabit performance and a full set of layer 2 networking management features at an affordable cost suitable for high performance workgroups and server applications With 10 100 1000Mbps RJ 45 ports and shared mini GBIC slots for fiber optic connection it delivers maximum throughput to high performance users or provides a backbone to a growing business network Package Contents Before you start installing the device verify the following items are in the package SP1684B Managed Switch Quick Installation Guide Manual CD RS 232 cable Mounting accessory Power Cord Physical Description SP1684B Front Panel Rear View Key Features Compliant with IEEE802 3 10Base T IEEE802 3u 100Base TX IEEE802 3ab 1000Base T and IEEE802 3z 1000Base LX SX standards SP1684B provide 24 RJ 45 ports of 10 100 1000M and 4 shared mini GBIC slots for fiber extension Support IEEE 802 3ad Link Aggregation up to 8 trunk groups up to 14 ports for each group Support IEEE802 1q tag based VLAN and IEEE802 1p traffic prioritization CoS Support broadcast storm control Sup
3. port jumbo frame up to 9216K bytes Support 802 1d STP 802 1w Rapid STP IEEE802 1s MSTP Support 802 1x port based authentication and port security with MAC address Support IGMPV1 IGMPV2 IGMPv3 Support SNMPV1 SNMPV2 SNMPV3 LED definition SP1684B LED light for port 1 24 Group LED Name LED color LED Function System POWER Green ON Power On OFF Power Off Port 1 24 LINK ACT Green ON Link at 10 100 Mbps OFF No Link BLINK Traffic Detected GIGABIT Amber ON Link at 1000 Mbps OFF Link at 10 100 Mbps or No Link RESET Button To restore switch configuration to factory defaults Press the Reset button for more than 10 seconds switch configuration will be restored to factory defaults and then reboots
4. test information No part of this document can be copied or reproduced in any form without written consent from the company WEEE Directive amp Product Disposal At the end its serviceable life this product should not be treated as household or general waste It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment or returned to the supplier for disposal 7 CE dp rene iy P N 2300 0643 n Configuration Web based User Interface Before using web management install the SP1684B on the network and make sure that any one of the PCs on the network can connect with the SP1684B through the web browser The default IP subnet mask username and password are as follows IP Address 192 168 1 254 Subnet Mask 255 255 255 0 User Name admin Password leave blank Login in the Console Interface When the connection between SP1684B and PC is ready turn on the PC and run a terminal emulation program or Hyper Terminal and configure its communication parameters to match the following default characteristics of the console port Baud Rate 38400 bps Data Bits 8 Parity none Stop Bit 1 After finishing the parameter settings click OK When the blank screen shows up press Enter key to bring out the login prompt Key in the admin default value for the User name and leave the Password field blank use Enter key to switch then press Enter key and the comma
Download Pdf Manuals
Related Search