Invacare® Matrx® Stabilite™Cushion User Manual
Contents
1. Cushion 3 3 Removing Installing the ThinAir Bladder Rear Strap es i ear Strap Soo Side Strap fo i ThinAir Bladder l Foam Contour Side Strap Foam Contour Cushion Removing the ThinAir Bladder Installing the ThinAir Bladder I Remove cushion from inner and outer l Center the ThinAir bladder on the foam so covers Refer to Removing Installing the that the side straps are centered in the Cushion Covers on page 5 contours on each side of the foam 2 Unfasten the the rear strap and the two side 2 Fasten the side straps and rear strap to the straps bottom of the foam 3 Lift the existing ThinAir bladder and remove it DO NOT over tighten the straps The from the cushion ThinAir bladder MUST be free to move with the cushion 3 Reinstall cushion into inner and outer covers Refer to Removing Installing the Cushion Covers on page 5 3 44 Removing Installing Removable Leg Wedges This procedure provides inch of lower seat to floor height on one side of the cushion This modification allows for easier foot propelling or the accommodation of some hip flexion limitations This modification can be done on either side of the cushion Top of Cushion Bottom of Cushion Removable Leg Wedges lt Hook and Loop Strips I Remove the cushion from the inner and outer covers Refer to Removing Installing the Cushion Covers on page 5 2 Remove the leg wedge from the side of the cushion that2. Teresa aetaval at alate aay Loop Portion of Fastening Strap Attached to Cushion l y Front of cushion lines up with front edge of seating surface Double Sided Hook Portion of Fastening Strap Remove backing if necessary l 1 l l l 1 I l Seating Surface i I I Hook Attachment Strips No Attachment Strips Remove double sided hook from bottom of cushion 2 Align front edge of cushion with front edge of seating surface 3 Perform one of the following Hook Attachment Strips Secure the cushion to the seating surface making sure that the strips of loop on the cushion cover are securely attached to the strips of hook on the seating surface e No Attachment Strips Place the cushion on the seating surface Loop Attachment Strips Verify the double sided hook strips are securely attached to the loop attachment strips on the bottom of the cushion 2 Align front edge of cushion with front edge of seating surface 3 Secure the cushion to the seating surface making sure that the double sided hook is securely attached to the strips of loop on the cushion cover and the seating surface Invacare Matrx Stabilite Cushion 4 Part No 1167615 3 2 Removing Installing the Cushion Covers WARNING The covers are designed to protect the foam from moisture and to provide fire retardency DO NOT use the cushion without either the inner or outer cover If the covers are torn they MUST
3. 1167615 7 Invacare Matrx Stabilite Cushion 6 Limited Warranty PLEASE NOTE THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4 1975 This warranty is extended only to the original purchaser user of our products This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state Invacare warrants this product to be free from defects in materials and workmanship for two years of use by original purchaser except for the cover which is warranted for a period of 90 days of use by the original purchaser If within such warranty period any such product shall be proven to be defective such product shall be repaired or replaced at Invacare s option with refurbished or new parts This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product Product repairs shall not extend this warranty coverage for repaired product shall end when this limited warranty terminates Invacare s sole obligation and your exclusive remedy under this warranty shall be limited to such repair and or replacement For warranty service please contact the dealer from whom you purchased your Invacare product In the event you do not receive satisfactory warranty service please write directly to Invacare at the address on the back cover Provide dealer s name address model number the date of pu
4. ITSG2020 21 ITSG2116 ITSG2117 ITSG2118 ITSG2119 ITSG2120 ITSG2121 ITSG2122 500 Ib 22 ITSG2216 ITSG2217 ITSG2218 ITSG2219 ITSG2220 ITSG2221 ITSG2222 227 kg 23 ITSG2316 ITSG2317 ITSG2318 ITSG2319 ITSG2320 ITSG2321 ITSG2322 24 ITSG2416 ITSG2417 ITSG2418 ITSG2419 ITSG2420 ITSG2421 ITSG2422 2 Safety Check ALL parts for shipping damage If shipping damage is noted DO NOT use Contact carrier dealer for further instruction 2 1 Intended Use WARNING The Stabilite cushion IS NOT designed for use in the treatment of pressure sores The Stabilite cushion is designed to provide pelvic stability and leg positioning for patients with postural asymmetry The Stabilite comes standard with a ThinAir bladder for managing shear under the pelvis Invacare Matrx Stabilite Cushion 2 Part No 1167615 2 2 General Warnings A WARNING DO NOT USE THIS PRODUCT OR ANY AVAILABLE OPTIONAL EQUIPMENT WITHOUT FIRST COMPLETELY READING AND UNDERSTANDING THESE INSTRUCTIONS AND ANY ADDITIONAL INSTRUCTIONAL MATERIAL SUCH AS OWNER S MANUALS SERVICE MANUALS OR INSTRUCTION SHEETS SUPPLIED WITH THIS PRODUCT OR OPTIONAL EQUIPMENT IF YOU ARE UNABLE TO UNDERSTAND THE WARNINGS CAUTIONS OR INSTRUCTIONS CONTACT A HEALTHCARE PROFESSIONAL DEALER OR TECHNICAL PERSONNEL BEFORE ATTEMPTING TO USE THIS EQUIPMENT OTHERWISE INJURY OR DAMAGE MAY OCCUR ACCESSORIES WARNING Invacare products are specifically designe
5. THE DURATION OF THE EXPRESSED WARRANTY PROVIDED HEREIN AND THE REMEDY FOR VIOLATIONS OF ANY IMPLIED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN INVACARE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE PROVINCIAL LAWS AND REQUIREMENTS Invacare Corporation www invacare com USA Canada One Invacare Way 570 Matheson Blvd E Unit 8 Elyria Ohio USA Mississauga Ontario 44036 2125 L4Z 4G4 Canada 440 329 6000 800 668 5324 Yes you can 800 333 6900 2011 Invacare Corporation All rights reserved Republication duplication or modification in whole or in part is prohibited without prior written permission from Invacare Trademarks are identified by and All trademarks are owned by or licensed to Invacare Corporation or its subsidiaries unless otherwise noted Part No 1167615 Rev A 072 1 1
6. User Manual DEALER This manual MUST be given to the user of the product USER BEFORE using this product read this manual and save for future reference Yes you can Invacare Matrx matry Stabilite Cushion Model ITSG General 1 1 Symbols Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage See the information below for definitions of the signal words WARNING A Warning indicates a potentially hazardous situation which if not avoided could result in death or serious injury CAUTION Caution indicates a potentially hazardous situation which if not avoided may result in property damage or minor injury or both Gives useful tips recommendations and information for efficient trouble free use 1 2 Overview Important Information The best way to avoid problems related to pressure sores is to understand their causes and your role in a skin management program Your therapist and physician should be consulted if you have questions regarding individual limitations and needs All cushions should be selected carefully Working with your therapist and physician is the best way to assure that a cushion choice matches your individual needs As the needs of the individual become more complex cushion evaluation becomes more important Matrx Stabilite Cushion The Invacare Matrx Stabilite cushion is developed to provide pelvic stabil
7. be replaced IMMEDIATELY Removing the Cover CAUTION A DO NOT remove both the outer cover and inner cover at the same time otherwise damage to the inner cover material may occur I Remove the cushion from the seating surface Refer to Attaching Removing the Cushion To From the Seating Surface on page 3 2 Unzip the outer cover 3 Remove cushion still inside the inner cover from the outer cover 4 Unzip the inner cover 5 Remove the cushion from the inner cover Part No 1167615 ThinAir Bladder a lt Cushion Installing the Cover l Ifthe inner cover has been removed position the cushion with the ThinAir bladder toward the rear of the inner cover The back surface of the cushion is marked REAR 2 Slide the cushion into the inner cover Zip the inner cover closed 4 Position the cushion with inner cover and the ThinAir bladder in place toward the rear of the outer cover bg When installed properly the ThinAir bladder is at the top of the inner cover The zipper is at the rear and the stretch fabric is at the top of the outer cover 5 Slide the cushion into the outer cover 6 Zip the outer cover closed CAUTION Use care not to snag the inner cover in the outer cover zipper or damage to the inner cover will occur 7 Reattach cushion onto seating surface Refer to Attaching Removing the Cushion To From the Seating Surface on page 3 Invacare Matrx Stabilite
8. d and manufactured for use in conjunction with Invacare accessories Accessories designed by other manufacturers have not been tested by Invacare and are not recommended for use with Invacare products INSTALLATION WARNING After any adjustments repair or service and before use make sure that all attaching component parts are secure WARNING Skin condition should be checked very frequently after the installation of any new cushion Your therapist and physician should be consulted if you have any questions regarding weight relief self examination of the skin or individual limitations and needs Make sure the hook and loop fastening straps are securely attached between the seating surface and cushion before using 3 Usage 3 1 Attaching Removing the Cushion To From the Seating Surface A WARNING Make sure the hook and loop fasteners are securely attached to the seating surface and to the cushion BEFORE using If the cushion is not secured to the seating surface use caution when transferring in and out of the wheelchair To remove the cushion from the seating surface reverse the following procedure The cushion attaches to the seating surface using the hook and loop fasteners on the bottom of the cover The seating surface can be seat upholstery drop base or seat pan The zipper on the cushion MUST ALWAYS face rearward Part No 1167615 3 Invacare Matrx Stabilite Cushion Zipper Faces Rearward CLL
9. ity and leg positioning for patients with postural asymmetry The Invacare Matrx Stabilite Cushion comes fitted with a patent pending Invacare ThinAir bladder a unique comfort layer that assists in shear management Outer Inner Covers The outer cover is made from a water resistant fabric to protect the foam The top is fabricated from a stretch fabric The bottom is fabricated from a heavyweight non skid fabric A water resistant inner cover allows air circulation while providing additional protection for the foam Regular cleaning and inspection of the outer and inner covers is recommended Refer to Care and Maintenance on page 7 Part No 1167615 l Invacare Matrx Stabilite Cushion 1 3 Weight Limitation and Model Numbers Refer to the chart for the model number and weight limitation Configured model numbers are ITSG ITSG Stabilite Cushion Bold Stock models Grey size not available WIDTH DEPTH WEIGHT LIMIT 15 16 17 18 19 20 21 22 15 ITSGIS5I5 ITSGI516 ITSG1517 ITSGI5I8 ITSGI5I9 ITSGI520 300 Ib l ITSGI6I5 ITSG66 ITSGI6 I7 ITSG68 ITSGI619 ITSGI620 136 kg 17 ITSGI7I5 ITSGI716 ITSGI7I7 ITSGI7I8 ITSGI7I9 ITSGI720 18 ITSGI8I5 ITSG86 ITSGI8I7 ITSG88 ITSGIBI9 ITSGI820 19 ITSGI9I5 ITSGI9IG ITSGI9I7 ITSGI9I8 ITSG1919 ITSGI920 20 ITSG2015 ITSG06 ITSG2017 ITSGOB ITSG2019
10. rchase indicate nature of the defect and if the product is serialized indicate the serial number Invacare Corporation will issue a return authorization The defective unit or parts must be returned for warranty inspection using the serial number when applicable as identification within thirty 30 days of return authorization date DO NOT return products to our factory without our prior consent C O D shipments will be refused please prepay shipping charges LIMITATIONS AND EXCLUSIONS THE WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO THE ENCLOSED INSTRUCTIONS IN ADDITION THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED PRODUCTS SUBJECTED TO NEGLIGENCE ACCIDENT IMPROPER OPERATION MAINTENANCE OR STORAGE OR PRODUCTS MODIFIED WITHOUT INVACARE S EXPRESS WRITTEN CONSENT INCLUDING BUT NOT LIMITED TO MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE PRODUCTS DAMAGED BY CIRCUMSTANCES BEYOND INVACARE S CONTROL PRODUCTS REPAIRED BY ANYONE OTHER THAN AN INVACARE DEALER SUCH EVALUATION SHALL BE SOLELY DETERMINED BY INVACARE THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES IF ANY INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IT SHALL NOT EXTEND BEYOND
11. requires a lower seat to floor height Save the leg wedge for future use Leg wedges secure in place with hook and loop strips 3 Install cushion into inner and outer covers Refer to Removing Installing the Cushion Covers on page 5 Invacare Matrx Stabilite Cushion 6 Part No 1167615 4 Care and Maintenance DO NOT use an abrasive detergent cleaner or cloth during maintenance 4 1 Cleaning Regular cleaning of the outer cover inner cover and cushion is recommended Outer Cover CAUTION DO NOT use fabric softeners or bleach DO NOT machine dry Air dry only DO NOT dry in sun Machine wash the outer cover in cold water on gentle cycle using a mild detergent Inner Cover Hand clean the inner cover using a soft cloth warm water and a mild soap solution Rinse off and hang dry Foam Wipe the foam with a damp cloth DO NOT submerge or soak 4 2 Inspection WARNING DO NOT continue to use this product if any of the upholstery materials foams and or plastics are found to be deformed breaking worn and or compressed Corrective maintenance can be performed at or arranged through your equipment supplier Regular inspection of the outer cover inner cover and cushion is recommended 5 After Use Reuse WARNING Risk of Injury Always have a dealer inspect the product for damage before transferring the product to a different user If any damage is found DO NOT use the product Otherwise injury may occur Part No
Download Pdf Manuals
Related Search