Harlan 8 Drive User Manual
Contents
1. i Neuralynx High Density Electrophysiology TX Systems Harlan 8 Drive User Manual Microdrive used for manually driving tetrodes for electrophysiology recordings Neuralynx Inc 105 Commercial Drive Bozeman MT 59715 Phone 406 585 4542 Fax 866 585 1743 www Neuralynx com Revision 1 0 support Neuralynx com 5 30 2013 Table of Contents lI Documpnt OVerviQw sarika san Aa aga A a DAK eed tu aded cud Na aaa TA a one ARA MD EM ga a ana a a 3 2 Harlan 8 Drive Vel Ie utana sunsu naqa EE Pa aa ng aaa maa a a 3 3 Glossa y kaanan q a a aaa a a Aa aga de ca Ba ag a a Ka aga taa a i Ta aaa a gga BA eh anah anan a aan 4 4 gt Dive Specifications e aga Aa EDR b ana qan na ag TA a a aga a dsb 5 Ds Diye Preparatiofi as aan sen tei ree dn aa gag aa A aaa hasc Ae a er a aa a sheave a E E an STANS 6 6 Micrt6drive TmplantatiO0n s u s saa i ea pute epist mas na a ngagagi alas aa Nah 11 T R cyclh eth Microdrive aae cd eia oet tes rect tesi a Pa a sds ag Ng ANGER sag ek aa ser AA 13 8 Appendix A Potential Vendor List i isst PRU tete qiti qe is trad edebat 15 9 Appendix B Replaceable Tip Hole Patterns rtri notoria rhet RES tuere ipea dnd 17 10 Appendix C Microdrive Parts Identifier nana 20 List of Figures and Tables Figure 5 1 Initial Telescoping Tube Assembly anana anana IO UR eMe 7 Figure 5 2 Final Tele2. cracks in the plastic drive plate Remove tetrode wires from the connector board It may be helpful to remove the board from the microdrive make note of the orientation of the board on the microdrive Some cactus needles will protrude through the board by 3 or more millimeters It may be best to cut all of the needles off with diagonal pliers so that about 1 mm protrudes Use a flat bladed screwdriver to pop the cactus needles back up through the plate Try to push on them straight along their axes to avoid bending and breaking If some do break use a flat ended piece of 015 music wire available at hobby shops held in a pin vise to push on the cactus needle The wire should extend only about 1 2 mm from the pin vise for the first push It may have to be extended more to push the loosened cactus needle out of the board After all of the needles and bits of tetrode wire have been removed from the board replace it on the microdrive Harlan 8 Drive User Manual Page 13 At this point the microdrive should be ready to be reassembled with new polyamide tube assemblies and a new replaceable tip Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 14 8 Appendix A Potential Vendor List Polyimide tubing PD Wire and Cable Trenton GA 800 241 1075 HVT Technologies Trenton GA 706 657 7700 MicroLumen Tampa FL 813 886 1200 Flat tip oilers S LaRose Inc Part No OL 350 extra small black Greensboro NC 888 752 767
3. of the 0196 tube This helps when inserting it into the 010 tube in the drive The top of the assembly should look like a stepped cone with both 012 and 0056 tubes extending equal amounts from their next larger tubes Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 7 TUN Figure 5 2 Final Telescoping Tube Assembly 6 Insert the drive screw into the Drive Assembly Fixture hole furthest from the top end of the fixture Push it in until the retaining nut seats against the fixture Insert the tube assembly into a drive plate and assembly fixture until the 0056 tube at the bonded end extends 2mm past the top surface of the plate Bond the assembly to the plate with Cyanocrylate adhesive If a gektype adhesive is used it is possible to just put a tiny fillet between the tube and drive plate and not have it wick down the hole This will facilitate removing the tube to recycle the microdrive Accelerator must be applied to achieve curing A small bottle that has a Luer top that can take a hypodermic needle is ideal for putting just a tiny drop on the glue Try not to touch the needle to the glue it can get clogged Use a 26 gauge or finer needle hold the bottle inverted and just let gravity form a drop on the tip of the needle 2 mm lt Figure 5 3 Drive Assembly 7 Cutthe tip guide tubes to 5 mm long Insert them into the holes drilled in the replaceable tip They should extend exactly 2 mm beyond
4. the replaceable tip Remove the upper cone Store the small screws in a secure place Remove all of the drives Cut a piece of insulated tungsten ground wire for the ground approximately 150 mm long Strip the insulation off both ends From the bottom of the lower cone feed the wire into the ground wire hole in the body This hole will be located between two drives near the outer periphery of the body and near the rear of the drive Slide the wire through until the end can be inserted into the ground hole on the connector board Secure it with a cactus needle and break off excess needle Insert the other end through the exit hole in the lower cone using forceps Pull the wire through leaving sufficient slack so that the wire won t snag on a drive Solder a lug fashioned from copper tin foil to make good contact with the ground screw The excess wire can be wrapped around the lower cone and taped in place temporarily with small bits of Scotch tape 2 Choose tip guide tube sizes and locations following instructions provided in Appendix B Replaceable Tip Hole Patterns The following list gives the tube inside diameters for a range of numbers of tetrodes going through one guide tube Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 6 It is assumed that the lower telescoping tube is 010 OD Wall thicknesses are suggested to be 002 003 No of tetrodes Guide tube ID 1 3 022 4 7 031 8 12 0457 3 Cut one piece of each
5. 2 mm above the top of the board Insert a cactus needle into each hole from the top of the board and push firmly to ensure contact ofthe wire with the circuit trace Break off the excess cactus needle Break off excess tetrode wire with forceps 15 After all the wires have been connected dress them away from the guide pins so there is no chance of binding or snagging as the drives are advanced Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 9 16 Gold plate the tetrodes using your standard protocol 17 Retract the tetrodes by backing out the drive screws until they are just free of the body Seal the intermediate tubes by touching the end of the guide tubes to a light mineral oil Blot off excess oil with an absorbent wiper The microdrive now is ready for implantation Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 10 6 Microdrive Implantation The following outline is meant to be a general guide to implanting the microdrive There will be variations according to particular animals and objectives of the research to be accomplished 1 25 10 11 12 13 14 15 Revision 1 0 5 30 2013 Shave head area around location of incision Secure anaesthetized animal in stereotactic fixture Make incision and hold skin apart with appropriate clamps Scrape away tissue over the skull Attenuate any bleeding Mark the stereotactic reference point on the skull e g Bregma with fine point p
6. 3 Dental acrylic Patterson Dental Hygenic Repair Resin veined Wilmington MA 800 842 5355 Small screws J I Morris Company Southbridge MA 508 764 4394 Tungsten ground wire A M Systems Inc Catalog No 7960 Carlsborg WA 003 wire 0045 dia insulated 800 426 1306 Cyanocrylate adhesives Any local hobby shop Pacer Zap Zap A Gap Slo Zap and Zap Gel Also house brands and accelerator Tower Hobbies Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 15 Champaign Il 800 637 4989 Home Depot Super Glue Gel and Future Glue Gel Dispensing bottle for accelerator Contact East Precision Dispenser Part No 121 723 800 225 5370 Needles Part No 121 755 009 ID Small Parts Squeeze Bottles Part No USQB 02 800 220 4242 Needles U NE 301PL or U NE 271PL Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 16 9 Appendix B Replaceable Tip Hole Patterns The following instructions are to be used to establish the hole locations and sizes for the Tetrode Microdrive replaceable tips This will ensure that the tip can accommodate the patterns that you want to use If your pattern is too large this procedure will reveal the problem l Revision 1 0 5 30 2013 Draw the proposed pattern on the centimeter graph paper at a scale of 10 1 millimeters become centimeters At each hole location mark a dot Place the graph paper over the template and hold them together against a light table or wi
7. Od 02 0d 02 15 Figure 9 1 Custom Exit Hole Template Harlan 8 Drive User Manual Revision 1 0 5 30 2013 Page 18 Anterior Posterior 16 Figure 10 2 Custom Exit Hole Graph Paper Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 19 10 Appendix C Microdrive Parts Identifier CONNECTOR BOARD COVER BODY ORIVE PLATE GUIDE RODS POLYIMIOE TUBE ASSY Z7 ATTACHMENT SCREWS DRIVEJ SCREV 09 90 X 3 32 HEX HEAD REPLACEABLE TIP INTERMEDIATE TUBE GUIDE TUBE Figure 10 1 Microdrive Parts Identifier The Harlan 8 Drive is compatible with Neuralynx s EIB 36 on left or modified with EIB 27 Micro on right Figure 10 2 Neuralynx s EIB 36 and EIB 27 Micro Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 20
8. ermanent marker Insert pointer in stereotactic holder and move over reference point Record axes coordinates Calculate burr hole coordinates Move stereotactic holder to first hole and mark location with permanent marker Repeat for other holes Remove pointer Mark locations for anchor screw holes and ground hole Drill screw holes with small dental burr being very careful not to penetrate the dura For the ground hole the dura is pierced Insert anchor screws suggested screws 3 32 00 90 or 0 80 hex head screws The bottoms of the heads should clear the skull by 5 to 1 5 mm Drill the burr holes with a core drill approx 1 3 mm dia Do not penetrate the dura Carefully scrape away the dura in the burr holes Attach the microdrive holder to the Stereotactic Adapter Attach the microdrive to the holder Move the first guide tube over the stereotactic reference point and lower the microdrive until the guide tube clears the skull by less than I mm Adjust the A P and Lateral coordinates until the guide tube is well centered over the Harlan 8 Drive User Manual Page 11 16 17 18 19 20 21 22 Revision 1 0 5 30 2013 reference mark Record the coordinates Calculate the new coordinates for the first guide tube and move the stereotactic fixture to them All of the guide tubes should be near the centers of their burr holes Unwrap the ground wire from the lower cone and attach it to the proper
9. h Cover 4 6 grams Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 5 5 Drive Preparation Before the microdrive can be used the replaceable tip must be drilled and assemblies of telescoping polyamide tubes must be built and attached to the microdrive These tubes provide the rigidity needed to precisely deliver the tetrode tips to the intended locations For each drive one tube is attached to a guide tube in the replaceable tip Three other tubes are telescoped together and attached to the drive plate After the drive is installed in the microdrive the tetrode is inserted in the innermost tube and bonded to it Four or more sizes of polyamide tubing are used in the microdrive The exact sizes and wall thickness may not always be available from tubing vendors There is some flexibility in choosing sizes it is best to try to get wall thickness specified here and adjust diameters as needed Try to provide 001 003 in diametral clearance between telescoping pairs of tubes The recommended sizes from smallest to largest are 0056 OD 0035 ID 001 wall 010 OD 008 ID 001 wall 012 OD 0065 ID 0028 wall 0196 OD 0135 ID 0030 wall Guide tubes in the replaceable tip may vary from 022 to 051 ID The following steps will ensure properly working drives Careful attention paid to tube lengths and assembly geometry will make the job of installing the drives easier 1 Remove the cover of the microdrive and
10. mide tubes must be built and attached to the microdrive The Drive Assembly Fixture aids with loading and the tube assemblies are inserted into the drive plate and bonded with an adhesive The tetrodes are fed through the guide tubes and the assembly is inserted with drive screws into the cone The tetrodes are gold plated the cone components are assembled and the drive is ready for experimentation A general implantation outline is provided but there will be variations according to particular animals and objectives of the research to be accomplished After experimentation recycling guidelines describe how the drive can be reused on other animals with a new replaceable tip and new polyamide tube assemblies Ray Harlan is the maker of this drive and can be contacted at Specialty Machining 15 Happy Hollow Road Wayland MA 01778 Phone and FAX 508 358 4013 rbharlan comcast net Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 3 3 Glossary Inner Diameter ID the inner diameter of the polyamide tubing Outer Diameter OD the outer diameter of the polyamide tubing EIB Electrode Interface Board Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 4 4 Drive Specifications Travel for each drive 7 5 mm Travel for each revolution of the drive screw 160 micrometers Tip area available for electrodes 4 4 mm diameter Height of microdrive 34 0 mm Diameter of microdrive 23 5 mm Weight Without Cover 3 8 grams Wit
11. ndow so that both sheets can be seen Select a hole size from the patterns shown The hole should be slightly larger than the tubing that is to go through it Slide the graph paper so that the hole outline is centered on the dot the small circle is an aid to centering Trace over the hole outline Repeat this procedure for the remaining proposed holes Note holes need not be all one size Move the graph paper until the hole pattern fits within the oval outline keeping the flat sides of the oval parallel to the coordinate frame on the graph paper If this cannot be done the hole spacing must be reduced or some holes must be eliminated If the hole pattern does fit within the oval trace the outline of the oval on the graph paper record the coordinates of the holes and their sizes and forward the graph paper coordinates hole sizes and the replaceable tip to Specialty Machining 15 Happy Hollow Road Wayland MA 01778 The pattern will be centered in the oval therefore it may be slightly displaced from your tracing If you have questions call 508 358 4013 or e mail to rbharlan comcast net Harlan 8 Drive User Manual Page 17 uu zQ T WW 66 UU 6 UU 6 WW T6 uU 6g UU bg Zara 06 0 0860 OLEO 09 0 OSEO OEEO Www wu Ww wul WW ww pers b vL QE 39 AH LS LS 0cE0 OTEO Zoco 08c0 2920 OSCO Orca GOCO ag 3 aD OD s d s
12. s to move the drive Guide the outer tube over the 010 tube as the drive is advanced 12 When all the tubes are telescoped test the freedom of the assembly by advancing the drive over the full travel range 7 5 mm Add the other drives and test their travel If there is any binding inspect the intermediate tubes near the bottom of the body to be sure there is no kinking Remove the drive and check that a separate piece of 010 tubing can be slid into the drive tube assembly up to the drive plate If excess Cyanocrylate has been used it may have wicked between the tubes and bonded them together If so replace the tube assembly with another If the outer tube does not pull out of the drive plate fairly easily soaking the tip of the drive plate in water for a few hours should soften the Cyanocrylate Try to keep the screw out of water 13 Make up the tetrodes according to your standard procedure Back off the drives until the heads of the drive screws are just below the ends of the guide pins This should keep the outer tubes in the body holes Insert the tetrodes in the inner tubes and slide them through until they are just flush with the tip guide tubes Bond them with Cyanocrylate adhesive to the tops of the inner tubes 14 Cut the tetrodes at 20 mm above the ends of the inner tubes Separate about 6 mm of the wires and feed them into their respective recording channel holes on the connector board The end of each wire should extend about
13. scoping Tube Assembly n anana eria eode tee taion 8 Fie re 2 2 Drive Assembly insan anaa ana hua npa addin Ta GEN E a aqa uuu 8 Figure 10 1 Custom Exit Hole Template ssmssmssssssrsrrsrsersesrrsrsrsrrersrsrrersrerrersrsrrrsrsrrrsrsrr renen anana anana anan 18 Figure 10 2 Custom Exit Hole Graph Paper oua e Deren ertt rre re bu ere Eee i Evan 19 E1eure L1 1 Micr drive Parts Identifier up ee tte pe t ettet e enia Ne gd a etis 20 Figure 11 2 Neuralynx s EIB 36 and EIB 27 Micro ee Pe eae Eee ine vta 20 Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 2 1 Document Overview The purpose of this manual is to outline assembly loading and general implantation of the Harlan 8 microdrive It also describes the appropriate preparation and recycling procedures surrounding the experiment Step by step instructions are outlined and additional products like the Drive Assembly Fixture are recommended to further facilitate this process 2 Harlan 8 Drive Overview The Harlan 8 Drive is an 8 tetrode microdrive that allows for recordings from a single brain structure or from two or more structures that fall on one line that extends from the skull surface into the depths of the brain The exit tip of this drive is solid and can be drilled by the researcher into their desired exit pattern or can be custom drilled for a small fee For initial drive preparation assemblies of telescoping polya
14. screw Take up excess slack in the wire by wrapping it back and forth around a pair of adjacent screws Lower the microdrive until the guide tubes touch the brain surface Hill around the bottom of the replaceable tip with Vaseline to seal the tip Mix small batches of dental acrylic and fill around screws and the replaceable tip slowly building up the mass with sequential batches Cover the screws ground wire and build up around the larger diameter of the replaceable tip Avoid getting cement on the lower cone except to secure the ground wire Also if cement is kept away from the replaceable tip attachment screws recycling the microdrive will be considerably easier The final shape of the cement mass should be smoothly formed around the tip and feathered out onto the skull to facilitate comfort for the animal Suture the incision bringing the skin over some of the dental acrylic Do not pull too tight Release the microdrive and remove the holder Remove the animal from the stereotactic fixture Harlan 8 Drive User Manual Page 12 7 Recycling the Microdrive After the microdrive has been removed from the animal it can be recycled for further use on other animals Because of the nature of various bonding techniques some parts must be discarded These include the replaceable tip and all of the polyamide tubes If care is taken when removing the tube assemblies from the drive plates the drives will be fully reusable The outline belo
15. size of tubing for each drive to be assembled Use a new single or double edged razor blade to avoid crushing the tubing Cut the following lengths 12 5 mm of 0056 OD 43 mm of 010 OD 2 mm of 012 OD 10 5 mm of 0196 OD e P The 012 tube is used as a spacer between the 0056 and 0196 tubes The thicker wall helps center the small tube The 010 tubing can be used instead if a small quantity of the 012 tubing cannot be obtained ask for a sample one foot piece which will make 150 assemblies 4 Slide the 2 mm length 012 tube over the 0056 tube so that 1 2 mm of the small tube extends past the end of the 012 tube Bond these together with a thin or gap filling Cyanocrylate adhesive such as Zap or Zap A Gap Use the point of a straight pin needle or a flat tip oiler black to apply the tiniest drop of adhesive and then use some accelerator if the bond does not set quickly Be very careful not to get any adhesive inside the smaller tube The thinner adhesive seems to do a cleaner Job Cut cured adhesive off the applicator frequently 5 mm Figure 5 1 Initial Telescoping Tube Assembly 5 Insert this assembly 0056 tube first into the 0196 tube until 2 mm of the 012 tube extends past the end of the large tube Bond this assembly together as in Step 4 again being careful not to get adhesive in the small tube Note that the 0056 tube extends about I mm past the bottom end
16. the end of the tip Bond them in place with Cyanocrylate adhesive 8 Remove the cover and replaceable tip Insert the first intermediate tube 010 OD into the appropriate tip guide tube and thread it into the body hole for the first drive Push it through until it exits the body hole Continue inserting intermediate tubes for the other drives Revision 1 0 Harlan 8 Drive User Manual 5 30 2013 Page 8 9 When all tubes are in place push the tip onto the body Fasten it with the 00 90 hex head screws supplied 10 Slide the intermediate tubes out of the tip guide tubes until 2 mm remains above the upper body surface Be especially careful when moving tubes that have neighbors in the same guide tube Friction could cause more than one tube to move disturbing the location of previously set tubes These may have to be held in place with fingers or some other clamping arrangement When all tubes are located in the body correctly bond them to the tip guide tubes with Cyanocrylate adhesive Be sure to fill all voids between tubes with adhesive Then cut the tubes off flush with guide tubes 2 mm from the end of the tip 11 Place a drive over the guide pins of the first drive so the pins enter the holes in the drive plate Slide the drive down until the smallest tube almost touches the intermediate 010 tube Guide the small tube into the 010 tube as the drive is moved further downward The drive screw now can be engaged in the body thread
17. w suggests a sequence to be followed 1 Revision 1 0 5 30 2013 Remove the replaceable tip If dental acrylic has been kept away from the attachment screws and most of the cone then only chipping it away from around the ground wire will be required Carefully work the adhesive off with a sharp knife until the tip can be removed Avoid cutting into any part of the lower cone When the tip is pulled away all of the intermediate tubes will go with it If there is any cement on the cone that isn t easily scrapped away it can be softened by soaking the cone still attached to the body but with drives removed in a shallow dish of acetone for an hour This makes the cement somewhat rubbery Remove the drives Cut the tetrode wires with scissors and the drives should be readily removable Remove the tube assemblies from the drive plates Cut the top of the tubes and any glue fillet off flush with the top of the drive plate with a sharp razor blade If care was taken to minimize the amount of Cyanocrylate used to attach the assembly to the plate the tube should pull out fairly easily If it resists use a 022 dia drill in a pin vise to clean out the tube remaining in the hole Be very careful not to twist the drill sideways in the hole and put excessive strain on the drive plate Do not apply any pressure to the drive screw or it may bend Do not attempt to use any debonder or other solvent to soften the adhesive they may produce stress
Download Pdf Manuals
Related Search