(PRO LIGHT) LED-FB8W USER MANUAL 04 09 2014(3)
Contents
1. 2j gun mz IU ODO 00 Q9 1 Fuse T 3 15A Protects the unit from the short circuit or over current 2 POWER IN Connection to supply power 3 POWER OUT Connects to supply power to the next unit 4 Only for remote control Used to connect to the CA 8 to control the unit for Stand by Function and Mode function 5 DMX IN OUT For DMX512 linking use 3 pin XLR cables to link the units together 6 Microphone Used to receive music for the sound activation 7 Function Display Shows the various menus and the selected functions 8 Button MENU To select the programming functions DOWN To go backward in the selected functions A UP To go forward in the selected functions ENTER To confirm the selected functions 9 LED DMX On DMX input present MASTER On Master Mode SLAVE On Slave Mode SOUND Flashing Sound activation To select any functions press the MENU button until the reguired function is showing on the display Select the function by pressing the ENTER button and the display will blink Use the DOWN and UP buttons to change the mode Once the reguired mode has been selected press the ENTER button to setup To go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode The main functions are s2. TILT1 TILT2 MOVEMENT Eg CHASE CHASE SPEED 255 255 255 100 248 255 E pues 255 Strobe by 233 247 Chase 16 Fast 248 255 Random Show 240 247 sound 218 232 Chase 15 218 247 Show 8 232 239 Open 203 217 Chase 14 188 217 Show7 188 202 Chase 13 a 190 231 Eastopen 173 187 Chase 12 128 1 sh Open 158 172 Chase 11 182 189 M 143 157 Chase10 098 127 Show 4 140 181 doso 128 142 Chase 9 192430 orem Chase pes picis TT 083 097 Chase 6 008 131 068 082 Chase 5 000 007 Blackout 053 067 Chase4 038 052 Chase 3 o L 60 000 007 023 037 Chase 2 Slow 008 022 Chase 1 0 000 007 Blackout 12 12 Channels Mode 12 Channels Mode MOVEMENT MOVEMENT DIMMER LED 1 LED2 255 450 255 450 255 248 255 Open 255 255 Strobe by 240 247 sound 232 239 Open Fast open 190 231 Slow 182 189 Slow open 140 181 Fast close 132 139 Open lt lt lt 008 131 o o x o L 60 o 60 0 000 007 Open 0 0 Ch10 Ch11 Ch12 LED3 LED 4 LED 5 LED 6 LED 7 LED 8 255 255 100 255 255 255 255 0 0 0 0 0 0 13 6 DMX Connection DMX OUT DMX CONTROLLE COMMON 1 DMX INPUT 2 DMX OUTPUT DMX Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of t
3. BUTTERFLY User Manual Please read the instruction carefully before use CONTENTS Safety NSU GETS a sul ET dn BEAR Sn Nd pal SRS A nehne kel 2 Technical LIONS s dod bird us 3 How To Set The asan or eyes to dia vecino peri x ded eu od 4 Control T ER 4 2 2 FUNCT OM eere 5 How to Control the Unit 10 4 1 Master Slave Built In Pre program Function sees 11 4 2 Easy GAB Controller seco er tete tee eet t vnb s 11 4 3 DMX CONROE Kea Tad Bike ones Und c RPM dS 12 DNX512 tot eb san Ra 12 COS GEO TB ka EY reped pat lep E edu o RD delen etum e DIEI dy du Kot A CR EUR ass 14 LEOSDIeSHOQUB8 y LL ena D TELLE 15 IE CUE Cen Eo een tato A al bv RR 15 1 Safety Instructions Please read the instructions carefully which includes important information about the installation operation and maintenance WARNING Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and freguency of power supply match the power reguirements of th
4. MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode Sirid SLAVE MODE To select the press the ENTER button to show SLAVE MODE on the display Use the DOWN UP buttons to select the MASTER EL 1 SLAVE 1 EC Ha SLAVE 2 modes ILI Once the mode has been selected press the ENTER button to setup to go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode SHOW MODE To select the Bh id press the ENTER button to show SHOW MODE on the display Use the DOWN UP buttons to select the En II Random show Show 1 or Show 8 mode Once the mode has been selected press the ENTER button to setup To go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode SOUND MODE To select the press the ENTER button to show SOUND MODE the display Use the DOWN UP buttons to select the sound on i sound off mode Once the mode has been selected press the ENTER button to setup To go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one min
5. NTER button and all channels of the unit will return to their standard position 4 How to Control the Unit You can operate the unit in three ways 1 By master slave built in pre program function 2 By easy CA 8 controller 3 By DMX controller You do not need to turn the unit off when you change the DMX address the new DMX address setting will take effect immediately Every time you power the unit on it will move all the motors 10 to their home position and you may hear some movement noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 4 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an and select show 8 Its DMX input jack will have nothing plugged into instant show You have to set the first unit in master mode 195 show 5h show 1 or or 55 it and its master LED will be constantly on and sound LED will flash to the music The other units will have to select normal or 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave LED lights will be constantly on 2 light show In slave mode means the unit works as the master unit and means 2 l
6. and press the MENU button for about one second or wait for about one minute to exit the menu mode TEMPERATURE To select the press the ENTER button to show the display and the display will show the temperature of the unit When the temperature is under 55 degrees C the fixture works normally when it s between 55 degrees C and 60 degrees C the fixture will reduce the power output and when it reach 65 degrees C or higher the LED will switch OFF To go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode FIXTURE HOURS To select the Er 2 press the ENTER button to show FIXTURE HOURS on the display and the display will show the number of working hours of the unit To go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode SOFTWARE VERSION To select the LE press the ENTER button to show SOFTWARE VERSION on the display and the display will show the version of software of the unit To go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode RESET To select the 2525 press the ENTER button to show the RESET on the display Press the E
7. d lenses must be replaced if they are visibly damaged Installation The fixture should be mounted via its Omega Ouick Release Clamp bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the fixtures weight Always use a safety cable that can hold 12 times of the weight of the fixture when installing The eguipment must be installed by professionals and it must be installed in a place where is out of the reach of people and no one can pass by or under it 2 Technical Specifications e 2 xrotating LED bars each with 4 pixel controlled 8W LEDs 3 Operation Modes DMX Master Slave and Sound Activation DMX Channel modes 1 6 12 channels Optional easy controller CA 8 for instant lighting show Great built in programs in master slave operation triggered by music Electronic dimming and various strobe effects Ideal for pubs clubs bars parties Mobile DJs and more Input Voltage AC 100 240V 50 60Hz Power Consumption 85 W Power Cable Daisy Chains 8 Fixtures 230V 50Hz 4 Fixtures Max 120V 60Hz LED 8 x 8W white LEDs e Weight 5 5kgs e Dimension 395 x 234 x 180mm E 395 180 138 KXXX Le 3 How To Set The Unit
8. e unit It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adeguate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Disconnect main power before replacement or servicing Make sure there are no flammable materials close to the unit while operating as it is fire hazard Use safety cable when installing this unit DO NOT handle the unit by taking its head only but always by taking its base Maximum ambient temperature is Ta 40 degrees C DO NOT operate it where the temperature is higher than this Unit surface temperature may reach up to 75 degrees C DO NOT touch the housing with bare hands during its operation Turn off the power and allow about 15 minutes for the unit to cool down before replacing or serving In the event of a serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts DO NOT touch any cables during operation as high voltage may cause electric shock Warning To prevent reduce the risk of electrical shock or fire do not expose the unit to rain or moisture The housing an
9. he last fixture 1 Connect the fixture together in a daisy chain by XLR plug cable from the output of the fixture to the input of the next fixture The cable cannot be branched or split to a cable 2 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected 3 The last units DMX cable has to be terminated with a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX of a 3 pin XLR plug and plug it in the DMX output of the last unit 4 Each fixture unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 5 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin 4 Pin 5 Not used 14 7 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The fixture does not work no light 1 Check the connection of power and main fuse B Not responding to DMX controller 1 DMX LED should be on If not check DMX cables to see if linked properly 2 If the DMX LED is on and no response to the controller check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the cables of the fixture or the previous one 4 Try another DMX controller C Some fixture
10. hown below DMX ADDRESS Li I CHANNEL MODE MOC MASTER MODE I SLAVE1 Cii SLAVE2 Lh Li RANDOM SHOW SHOW 178 SOUND MODE BLACKOUT MODE LED DISPLAY DISPLAY NORMAL DISPLAY INVERSION TILT 1 INVERSION TILT 2 INVERSION REV 1 AUTO TEST TEMPERATURE TEST 1 FIXTURE USE TIME FIRMWARE VERSION RESET DMX 512 ADDRESS To select the press the ENTER button to show DMX ADDRESS the display Use the DOWN UP buttons to adjust the address from 1 to 512 Once the address has been selected press the ENTER button to setup To go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode CHANNEL MODE To select the Litic press the ENTER button to show CHANNEL MODE on the display Use the DOWN UP buttons to select the 1 6 12 channel modes Once the mode has been selected press the ENTER button to setup To go back to the functions without any changes press the
11. ight show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only 4 2 Easy Controller The easy remote control is used only in master slave mode By connecting to the 1 4 jack socket of the first unit you will find that the remote controller on the first unit will control all the other units for Stand by Function and Mode selection Blackout Blackout the unit 1 Sound Strobe Full On Select Show 2 Auto Strobe Full On Show 1 8 bd Random Show Show LED OFF LED ON 11 4 3 DMX Controller By using a universal DMX controller to control the units you have to set DMX address from 1 to 512 so that the units can receive DMX signal Press the MENU button up to when 1997 is showing on the display Press the ENTER button and the display will blink Use the DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to setup To go back to the functions without any changes press the MENU button again Please refer to the following diagram to address your DMX512 channel for the first 4 units 1CHANNELMODE B ll H 6 CHANNEL MODE TM III 12 CHANNEL MODE LL dE I 5 DMX512 Configuration 1 6 Channels Mode 1 Channel Mode 6 Channel Mode Chi Ch2 ch3
12. r normal mode Once the mode has been selected press the ENTER button to setup To go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode TILT 2 INVERSE To select the lt ii press the ENTER button to show TILT 2 INVERSE on the display Use the NN I DOWN UP buttons to select the 525 tilt 2 inversion or normal mode Once the mode has been selected press the ENTER button to setup To go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode REV MODE To select the press the ENTER button to show REV the display Use the DOWN UP buttons to select the 525 the projector lenses will light up right to left or normal the projector lenses will light up right to left mode Once the mode has been selected press the ENTER button to setup To go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode AUTO TEST press the ENTER button to show TEST on the display and the unit will run a To select the self test To go back to the functions without any changes press the MENU button again Hold
13. s don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the unit Set the correct address D No response to the sound 1 Make sure the fixture is not receiving a DMX signal 2 Check microphone by tapping it 3 Make sure the fixture is not set into Blackout mode 8 Fixture Cleaning The cleaning must be carried out periodically to optimize light output Cleaning freguency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics 15 Clean with soft cloth using normal glass cleaning fluid Always dry the parts carefully Clean the external optics at least every 30 days 16 Declaration of Conformity We declare that our products lighting eguipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility Directive 89 336 EEC EN55103 1 2009 EN55103 2 2009 EN62471 2008 EN61000 3 2 2006 A1 2009 A2 2009 EN61000 3 3 2008 8 Harmonized Standard 60598 1 2008 All 2009 EN 60598 2 17 1989 A2 1991 EN 62471 2008 EN 62493 2010 Safety of household and similar electrical appliances Part 1 General reguirements 18 Innovation Ouality Performance
14. ute to exit the menu mode 1 BLACKOUT MODE L press the ENTER button to show BLACKOUT MODE on the display Use the To select the I DOWN UP buttons to select the blackout or normal mode Once the mode has been selected press the ENTER button to setup To go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for about one minute to exit the menu mode LED DISPLAY To select the Led press the ENTER button to show LED DISPLAY on the display Use the LED off mode Once the mode has DOWN UP buttons to select the LED on or been selected press the ENTER button to setup go back to the functions without any changes press the MENU button again Press and hold the MENU button for about one second or wait for one minute to exit the menu mode DISPLAY INVERSE 7 press the ENTER button to show DISPLAY on the display Use the DOWN UP To select the buttons to select the 8158 normal or HS 2 inversion press the ENTER button to setup To go back to the functions without any changes press MENU button TILT 1 INVERSE press the ENTER button to show TILT 1 INVERSE on the display Use the To select the NN DOWN UP buttons to select the tilt 1 inversion o
Download Pdf Manuals
Related Search