VQ-Series Real Time Splitter User Manual
Contents
1. Relay Normally Open 12 Relay Common 13 Relay Normally Closed 14 Remote Keyboard Input RS485 15 Remote Keyboard Input RS485 For RS232 remote control e Connect Pin 14 to Pin 5 e Connect RS232 data TXD to Pin15 e Connect RS232 ground to Pin 5 The cable required for control from a PC with a 9 way D type on its RS232 COM port is as follows PC VQ Series Splitter 3 15 14 ES 5 The VQ Series Splitter can be controlled using the PC VDM Remote available free of charge from www videoswitch co uk Videoswitch 7 Vq601c doc2. P position UP position DOWN position LEFT position RIGHT Left Vertical Select vertical Not used Select vertical CROP Select vertical Split SQUASH mode mode and move CROP mode and position LEFT move position RIGHT Right Select vertical Not used Select vertical CROP Select vertical Vertical SQUASH mode mode and move CROP mode and Split position LEFT move position RIGHT Upper Select horizontal Select horizontal Select horizontal Not used Horizontal CROP mode and CROP mode and SQUASH mode Split move position UP move position DOWN Lower Select horizontal Select horizontal Select horizontal Not used Horizontal CROP mode and CROP mode and SQUASH mode Split move position UP move position DOWN Videoswitch 6 Vq601c doc VQ Series Real Time Splitter User Manual 04 08 2004 17 25 3 3 1 Exit SETUP Mode When you have finished configuration press the ALT key and HH key again to quit All settings will be saved including the screen mode being displayed when this is done If no keys are pressed for 30 seconds SETUP mode will automatically be terminated 4 Keyboard amp Alarm Connector Pin Outs Y 5 Description Alarm 2 Alarm 4 Do not connect Do not connect Ground Alarm 1 Alarm 3 Do not connect Do not connect 0 0 N OD oy BR Ow P O Connect to Pin 15 to terminate the RS485 input unless the twisted pair is being daisy chained to another terminated device 11
3. Videoswitch VQ Series Real Time Splitter User Manual Products covered by this manual VQ 402M Monochrome Real Time Quad and PIP VQ 402C Colour Real Time Quad and PIP VQ 403C Colour Real Time Quad PIP Dual PIP Vertical Split Horizontal Split Document Ref Vq601c doc Date 04 08 2004 Videoswitch Telephone 01252 851510 Units 15 amp 16 Fax 01252 851296 Redfields Industrial Park Email sales videoswitch co uk Redfields Lane Web www videoswitch co uk Church Crookham Hants GU52 ORD VQ Series Real Time Splitter User Manual 04 08 2004 17 25 Videoswitch 2 Vq601c doc VQ Series Real Time Splitter User Manual 04 08 2004 17 25 Contents Y Installation ni iaa 1 1 Connecting picada la a A ios 4 1 2 A ON AT E TEAN 4 2 TODO ION la 2 1 NE A RON 4 2 2 AM SS A A CN 4 2 3 FollScrecn Selecione 5 2 4 Auto Sequencing 2 5 Remote Keyboard 3 Configuration cra 3 1 Restore Factory Defaults ici A tad ca sberbieddereadits 5 3 2 Set Remote Control Address cis E a 5 3 3 ea EN EANN Keo e EEEE ATA E A E A A A A sur desuesnusansdduchesdeatsuetadestdeeuestea deans 6 3 3 1 Exit SETUP Mod ii a 7 4 Keyboard amp Alarm Connector Pin OuktsS oooomoosoomsmmsss 7 Videoswitch 3 Vq601c doc VQ Series Real Time Splitter User Manual 04 08 2004 17 25 1 Installation 1 1 Connecting Up The diagram below shows the connector arrangement on the rear panel unit viewed from rear Note that l
4. eries Real Time Splitter User Manual 04 08 2004 17 25 Model Modes VQ 402M e Full Screen VQ 402C e Quad e PIP picture in picture VQ 403C e Full Screen e Quad e PIP e Dual PIP e Vertical Split e Horizontal Split 2 3 Full Screen Selection To display a full screen image press camera key 1 2 3 or 4 2 4 Auto Sequencing To switch auto sequencing ON press and hold a camera key then momentarily press the key To cancel auto sequencing press any camera key or select a multi screen mode 2 5 Remote Keyboard The unit may be remotely controlled by any Videoswitch VK series remote keyboard or by a computer running suitable software 3 Configuration A number of user preferences may be configured using the SETUP mode These settings are stored when power is removed The factory default settings can be easily restored to provide known starting conditions Note that all cameras should be connected when using SETUP mode so that you can see the effects of any changes made This unit does not generate on screen text 3 1 Restore Factory Defaults To restore the factory defaults hold the ALT key on while turning on the power Note that the default screen mode is QUAD 3 2 Set Remote Control Address The address that the unit uses for control via a remote keyboard is set as follows To set the unit address hold the ALT key and one of the camera select keys 1 2 3 or 4 while turning on the p
5. ettering for the camera numbers on the actual rear panel may be in error this diagram shows the correct numbering Videoswitch VQ REAL TIME SPLITTER O KBD amp ALARM 12V DC INPUT DIO e Connect cameras to BNC inputs 1 2 3 and 4 lower row If the unit is being used just as a two way horizontal or vertical splitter VQ 403C only connect cameras to inputs 1 and 2 only e f required loop through cameras to other equipment 1 2 3 and 4 upper row e Connect monitor s to BNC and or S Video outputs e Plug inthe 12V power supply to the 3 pin Mini DIN connector e If alarms are to be used connect normally open contacts KBD amp ALARM connector refer to section 4 e lf a remote keyboard is to be used connect twisted pair to KBD amp ALARM connector refer to section 4 1 2 Termination In normal use where the camera signals connect only to this quad the four DIL switches under the unit should all be ON If cameras are looped through to other equipment that terminates the video then the corresponding DIL switch sections should be turned OFF 2 Operation 2 1 Power Up Plug the flying lead of mains power adaptor into the 12V DC power input connector Plug the adaptor itself into the mains supply 2 2 Multi Screen Selection Press the key to step through the available multi screen modes The screen modes that are provided on the different models are Videoswitch 4 Vq601c doc VQ S
6. ower The unit address will be set to 1 2 3 or 4 respectively Videoswitch 5 Vq601c doc VQ Series Real Time Splitter 3 3 SETUP Mode Enter SETUP mode by pressing and holding on the ALT key then pressing the User Manual key 04 08 2004 17 25 SETUP mode may be entered from any of the screen modes and the screen mode may also be changed while in SETUP mode by pressing the key While in SETUP mode a small black square at the top left of the screen is displayed or a larger area of black Each of the screen modes allows you to set different things using camera keys 1 2 3 and 4 The function of the camera keys for each SETUP screen mode is shown here 1 2 3 4 Full Screen Press to toggle auto Press once to start Not used Not used sequencing ON or the auto sequence OFF DWELL timer Press again when the required time has elapsed Quad Press to ENABLE or Press to start alarm Press to start alarm Press to start alarm DISABLE the alarms HOLD time Press SEQUENCE time RELAY HOLD time factory default is again when the Press again when the Press again when ENABLE required time has required time has the required time elapsed elapsed has elapsed PIP Move main PIP Move main PIP Move main PIP Move main PIP position UP position DOWN position LEFT position RIGHT Dual PIP Move second PIP Move second PIP Move second PIP Move second PI
Download Pdf Manuals
Related Search