Verti-Comb Serial number:
Contents
1. Figure 6 To remove the pallet and to place the machine horizontally on the ground you take the following steps see Figure 6 NEVER CRAWL UNDER THE MACHINE 1 Attach a cable to lifting point 1 and to the frame of the machine 2 A Make sure that the cable crane lift can hoist minimum 1 000 kg 2205 Ibs A Careful Keep your distance the machine can slide 2 Remove the bottom 3 points pins 4 3 Lift the machine carefully a little bit off the pallet 4 Remove the pallet and lower the machine calmly until it stands completely on the ground 5 Connect the machine to the tractor please refer to Chapter 3 0 A Use the proper tractor please refer to the specific2. Figure 10 The machine can be disconnected in the following manner see Figure 10 I Make sure that the tractor is blocked well and cannot move on its own accord A Switch off the tractor before descending Fold the side panels up and mount the locking pins in the securing pins Drive the Verti Comb to a parking area with a firm flat surface Lower the adjustable legs and secure these with the locking pins Carefully lower the Verti Comb to the ground Release the top rod Take the securing pin out of the top rod pin and pull the pin out of the top rod connection Take the securing pins out of the bottom 3 point pins and disconnect the lower lifting arms from the tractor MORONS N A 1 Make sure that the Verti Comb stands stable and cannot roll away and or slide off 8 Start the tractor and drive off 9 0 TROUBLE SHOOTING PROBLEM ANALYSIS Problem Possible cause Solution Levelled too little material Ground is too hard Drive another few passes Use rakes Sloppy image of the field after Ground is too wet Wait for better conditions processing Increase the driving speed You have driven too slowly Optional Rakes go too deep Wrongly adjusted
3. 13 10 0 EU DECLARATION udin a ag ara equ Era ads 14 11 0 MAINTENANCE iani ssa caduta cuu dx nd aa Eus a dd nda bank d as bala oa xa dara cV ia ada 14 12 0 OPTIONAL SET OF WHEELS WITH TOWING HOOK 15 13 0 OPTIONAL RAKE nente enne 16 14 0 OPTIONAL MAGNET 17 15 0 OPTIONAL HYDRAULIC 18 1 0 TECHNICAL DATA Model Verti Comb Working width 1 8 m 70 9 only the middle section 4 0 m 157 5 Working depth Surface treatment Speed Maximum 12 km h 7 5 mph Weight of basic machine Weight of basic machine including options 250 kg 551 Ibs 545 kg 1202 lbs Recommended tractor 30 HP with minimum lifting capacity of 700 kg 1543 2 Ibs In case of the hydraulic version 1 double functioning hydraulic connection Maximum capacity Theoretical at maximum speed of 12 km h 7 5mph 48000 m h 516667 7 ft h Transport dimensions LxWxH 1175 x 2220 x 1 610 mm 46 3 x 87 4 x 63 4 Three point connection Cat 1 2 Standard components Integrated adjustable legs Optional Set of wheels Towing hook Rake section Magnet section Hydraulic kit 2 0 FIRST INSTALLATION TAKING THE MACHINE OFF THE PALLET
4. Swivel the top rod out Adjust the working depth 13 10 0 EU DECLARATION We Redexim BV Utrechtseweg 127 3702 AC Zeist Holland declare entirely under our own responsibility that the product VERTI COMB WITH MACHINE NUMBER AS INDICATED ON THE MACHINE AND IN THIS MANUAL to which this declaration relates is according to the stipulation of the 2006 42 EC directive for machines Zeist 01 10 09 wc A C Bos Manager Operations amp Logistics Ca Redexim Holland 22 11 0 MAINTENANCE Time schedule Check Grease point Method Before every use Check for loose bolts nuts Tighten loose bolts nuts with the correct torque If installed Replace or repair components Check the hydraulic system for damage Replace these if not present or Presence and readability of the damaged safety stickers Figure 5 14 12 0 OPTIONAL SET OF WHEELS WITH TOWING HOOK The Verti Comb is also available including a set of wheels optional Figure 11 This set can be mounted at the inside of the machine The set of wheels is used in combination with a towing hook when another pulling vehicle is used instead of a tractor Figure 11 15 13 0 OPTIONAL RAKE SECTION The Verti Comb is also available including a rake section optional Figure 12 This section can be mounted at the front side or the backside of the machine The rake section can be used to rake loosen any material that is
5. User Manual and Parts Book of the 3709 JA Zeist the Netherlands T 31 30 6933227 F 31 30 6933228 Ve rt i C O m b E verti drain redexim com www redexim com Serial number Translation of the original operating instructions ATTENTION IT IS OF THE UTMOST IMPORTANCE TO READ THIS USER MANUAL CAREFULLY PRIOR TO USING THE VERTI COMB IN ORDER TO USE THE MACHINE SAFELY AND TO OBTAIN THE BEST RESULTS 0948 English 942 120 200 FOREWORD Congratulations on your Verti Comb purchase For safe and long lasting operation of this Verti Comb it is necessary to read and to understand this user manual It is impossible to work safely with this machine without complete knowledge of its content The Verti Comb is not a machine that works independently It is the user s responsibility to use the correct tractor The user must also check the tractor Verti Comb combination on safety aspects such as noise level user instructions and risk analysis The following pages deal initially with the general safety instructions Every user should know these safety instructions and apply them At the end of this page a registration card is inserted This registration card should be returned to enable us to deal with pote
6. VERTI COMB Before using the Verti Comb in a location you should check the following items 1 Are there loose objects in the field First remove these objects 2 Are there slopes The maximum slope is 20 degrees for this machine 3 Is there danger of flying objects e g balls that distract the attention of the driver If so the Verti Comb CANNOT be used 4 Is there danger of sinking sliding away If so postpone the processing until conditions improve 5 A field can be worked several times in the same or different directions in order to obtain better processing 6 Do not make sharp bends and preferably drive in straight lines otherwise you might damage the machine and the ground 7 0 START STOP PROCEDURE Figure 9 The start procedure is VERY important If this procedure is not executed as described below it might result in serious damage to the subsoil The start procedure is as follows see Figure 9 1 A S gt S Check the Vert
7. ance and repairs Only authorised technical personnel may carry out repairs to the Verti Comb Keep a record of the repair activities The general applicable health amp safety Dutch ARBO regulations must also be followed in addition to the instructions in this user manual Relevant traffic regulations also apply in case of using public roads Transporting persons is not permitted Do not use the Verti Comb in the dark in heavy rain storm or on slopes with an angle larger than 20 degrees All persons that are going to operate the Verti Comb must be familiar with all the functions and control elements of the Verti Comb before starting any work activities Attach the Verti Comb to the towing vehicle according to the regulations Danger of injuries Check whether you have a clear field of vision both close by and far away before you depart Safety stickers Figure 2 3 and 4 With an identical meaning are attached to both sides Figure 5 of the Verti Comb These safety stickers must always be clearly visible and legible and must be replaced if they have become damaged During operation NO persons are allowed within the danger zone of the Verti Comb because there is danger of physical injuries caused by flying material Figure 3 933 280 402 Figure 3 Figure 4 Keep a distance of minimum 4 metres Figure 4 Pay attention to the permitted lifting capacity of the towing vehic
8. ations Turn off the tractor and secure the tractor Verti Comb combination against driving off and or sliding off 3 0 ATTACHING IT TO THE TRACTOR Checking procedure before starting to attach the Verti Comb Check the Verti Comb for visually discernable damage and repair this if safe operation of the machine is no longer guaranteed Check whether all the nuts and bolts are tight Check whether all safety stickers are present on the machine and are not damaged NEVER use the machine without these items Figure 7 The Verti Comb can be attached to the tractor by means of the 3 point attachment The procedure is as follows see Figure 7 1 Remove the 3 point pin 2 2 Drive the tractor carefully backwards so that the lower connecting arms can be attached to the frame Make sure that the pulling vehicle is blocked well and cannot move its own accord A 1 Switch off the pulling vehicle before descending 3 Connect the lower connecting arms to the 3 point pins 1 and secure these with the supplied locking pi
9. g its operations that have a negative impact on safety must be rectified immediately For safety reasons it is in principle not permitted to make changes or adjustments to the Verti Comb except those approved by the manufacturer If modifications to the Verti Comb have been made then current CE marking is cancelled The person that has made these modifications has to apply for a new CE marking himself Check the Verti Comb for loose bolts nuts and components before every operation If present check the hydraulic pipelines regularly and replace these when the hydraulic pipelines are damaged or appear old The pipelines that are replaced should comply with the technical requirements of the manufacturer If a hydraulic installation is present you should always make it pressure free before working on this installation NEVER use the Verti Comb in the absence of the safety stickers NEVER crawl under the Verti Comb If necessary tilt the Verti Comb NEVER step off the tractor while the motor is running In case of maintenance adjusting and repairs it is necessary to block the Verti Comb in order to prevent sinking away driving off and or sliding off Always switch off the tractor motor and take the tractor s key out of the ignition in carrying out maintenance adjustments and repairs Figure 2 Figure 2 With regards to the safety of the machine and the user use only original Verti Comb parts for mainten
10. i Comb for loose components and look whether all components function properly If loose components are observed or components do not function properly the problems must be solved before using the Verti Comb Drive to the location that needs to be treated and lower the machine until it is completely on the ground Make sure that the tractor is blocked well and cannot move on its own accord Switch off the tractor before descending Remove the locking pins and unfold the side panels Turn the top rod tight until the machine stands completely flat on the ground Move the tractor forwards Increase the driving speed to maximum 12 km h 7 5 mph 12 Stopping occurs as follows 1 Lower the speed and lift the machine from the ground 2 Lift the machine completely and drive to the next location 8 0 DISCONNECTING THE VERTI COMB
11. ies and or damage 1 The user must be an expert in using the machine The machine should be professionally adjusted for cultivating the subsoil The manufacturer will not accept any liability for unprofessional use and its resulting damage All risks occurring with this are entirely at the expense of the user Not following the use maintenance and repair instructions prescribed by the manufacturer is also considered unprofessional use of this machine Inspect the area to be treated before using the Verti Comb Remove loose obstacles and avoid irregularities The Verti Comb is manufactured according to the latest technical understanding and is safe to use When unskilled people use maintain or repair the machine this could result in injuries to the user and to third parties This must be avoided Always use the Verti Comb in combination with the correct tractor as described in the technical data All persons assigned to operate maintain and repair the Verti Comb by the owner must read and completely understand the operation manual and in particular the chapter of Safety Instructions The user is responsible for a safe Tractor Verti Comb combination This entire combination must be tested for noise safety risk and user friendliness User instructions should also be drafted The user is obliged to check the Verti Comb for visible damage and defects before using the Verti Comb Modifications to the Verti Comb includin
12. le Dress appropriately Wear sturdy shoes with steel toecaps long trousers and tie up long hair Do not wear loose clothing 900 280 402 Figure 5 7 Location of the safety stickers Figure 5 TABLE OF CONTENTS WARRANTY CONDITIONS anas vd ania ix ni pana iu Eau c ik aid ad 2 dura Exibia uma eurn Pa rigo Su E km drm Ras 2 SAFETY INSTRUCTIONS rr i ca ar i rd 3 1 0 TECHNICAL DATA 2 ie MAURUS EK NAMES 8 2 0 FIRST INSTALLATION TAKING THE MACHINE OFF THE PALLET 9 3 0 ATTACHING IT TO THE TRACTOR cernere 10 4 0 TRANSPORTING THE VERTI COMB eere 11 5 0 DRIVING SPEED cb 11 6 0 OPERATING THE VERTI CONMB eene nennen 12 7 0 START STOP PROCEDURE bora ed xa re EL lona rr ar aee 12 8 0 DISCONNECTING THE VERTI CONMB eene 13 9 0 TROUBLE SHOOTING PROBLEM ANALYSIS
13. ns 4 Set the stabilizer of the tractor to 100 mm lateral stroke 5 Mount the top rod of your tractor and turn it outward until it reaches the same height as the 3 point stop connection of the Verti Comb 10 Connect the top rod 3 to the frame with the pin 2 secure the pin 2 with the supplied securing pin Turn the top rod inwards so that it becomes pressurized A Make sure that all the securing pins are locked Start the tractor and lift the Verti Comb off the ground Detaching is done in reverse order 4 0 TRANSPORTING THE VERTI COMB Figure 8 The user is responsible for transporting the Verti Comb in back of the tractor on public roads Verify the national legislation regarding the regulations On open fields while the machine is raised the maximum permitted speed is 12 km h 7 5 mph due to the weight of the Verti Comb A higher speed can be dangerous for the driver and or the public and can even damage the machine A When the machine is raised off the ground the front axle of the tractor has to support minimum 20 of its weight A Always transport the Verti Comb with the side panels folded Secure the locking mechanism 1 with the locking pin see Figure 8 5 0 DRIVING SPEED The driving speed is limited to 12 km h 7 5mph It is NOT recommended to drive faster due to the fact that excessive wear amp tear damage can occur to the machine and to the subsoil 11 6 0 OPERATING THE
14. ntial future claims This user manual lists many instructions that are numbered in sequence You should follow this sequence ACS is an indication of a safety instruction A AN means a tip and or note All information and technical specifications provided at the moment that this document is published are the most recent ones Design specifications may be changed without prior notice This document is a translation of the original operating instructions Upon request the original operating instructions are available in Dutch WARRANTY CONDITIONS WITH DELIVERY THIS VERTI COMB IS GUARANTEED AGAINST MATERIAL DEFECTS THIS WARRANTY IS VALID FOR A PERIOD OF 12 MONTHS FROM THE PURCHASE DATE VERTI COMB WARRANTIES ARE SUBJECT TO THE GENERAL CONDITIONS FOR SUPPLY OF PLANT AND MACHINERY FOR EXPORT NUMBER 188 THAT ARE PUBLISHED UNDER THE AUSPICES OF THE UNITED NATIONS ECONOMIC COMMISSION FOR EUROPE REGISTRATION CARD For your own information fill in the table below Serial number of the machine Dealer name Date of purchase Remarks SAFETY INSTRUCTIONS Figure 1 to the Verti Comb The Verti Comb is designed for safe use This can only be achieved if you completely follow the safety instructions described in this manual Read and understand Figure 1 the manual before you start using the Verti Comb If the machine is not used as described in this manual this can result in injur
15. stuck iet sagr T m E PeF NT uu in tn nimis cen anni thy ran eap BELLY My i ty ie P tim 5 Sapun nu jill Ld oot nau Figure 12 16 14 0 OPTIONAL MAGNET SECTION The Verti Comb is also available including a magnet section optional Figure 13 This section can be mounted at the backside of the machine While treating the surface the magnet section can be used to remove steel particles from the surface T agr oy C E r f E RI I l aft qq qm qnm PS l 1 L Su TU unm a ntti sa A 4 1 ag al m etn A i idi P it P 2 Figure 13 17 15 0 OPTIONAL HYDRAULIC KIT The Verti Comb is also available including a hydraulic kit optional Figure 14 This kit can be mounted on the backside of the machine by means of brackets The hydraulic kit enables the automatic folding up or down of the side panels and the automatic raising or lowering of the set of wheels lt a gt qan 5 Vin iy 0 in TIT ITE Figure 14 18
Download Pdf Manuals
Related Search