"user manual"
Contents
1. Method 2 good Using AUDIO IN Jacks Connect the AUDIO IN jacks from the unit to the AUDIO OUT jacks on TV SAT Cable Box VCR or other component Press either SOURCE button on the main unit or AUX button on the remote control to select AUX mode SAT _VCR____ Cable Box AUDIO QUT Audio cable not included Connecting your player to a wired net work router optional Connect an Ethernet cable CAT5 or better with RJ45 connector to the ETHERNET jack on the back of your player and to an Ethernet jack on a network hub or broadband router Hub or broadband router LAN cable not included Donotconnect a modular phone cable to the ETHERNET jack e When plugging or unplugging the cable hold the connector on the end of the cable When unplugging do not pull on the cable Press down the lock tab and pull the connector out of the jack e Because there are various connection configurations follow the instructions from your Internet service provider Connecting AUDIO OUT to an auxilliary Audio System optional connection This system has AUDIO OUT jacks allowing you to connect to auxiliary audio systems such as a second audio amplifier or perhaps a wireless audio transmitter Audio System Audio cable not included Connections and Setup Connecting the Speakers Speaker wires are color coded to m2. A ake Courtesy Dolby Laboratories 1 Left Right Front Speakers Front speakers carry primarily music and sound ef fects 2 Center In surround mode the center speaker carries most of the dialog as well as music and effects It should be set between the left and right speak ers 3 Surround Rear Speakers The surround speakers overall sound balance should be as close as possible to the front speakers Proper placement is vital to establish an evenly dis tributed sound field 4 Subwoofer A subwoofer is designed to reproduce powerful low bass effects explosions the rumble of spaceships etc ase Note Center speaker provided with this unit is magnetically shielded to protect your TV set It is not recommended to place speak ers without magnetic shield near the TV set Front Speaker Placement For best results follow the speaker placement below Alignment Align the center speaker evenly with A or slightly behind B the left and right speakers but not ahead of them Angle Place the left and right speakers to form a 45 degree angle with your favorite viewing position to dupli cate the soundtrack mixer s perspective Height The three front speakers should be as close as pos sible to the same height This often requires placing the center speaker directly on top A or beneath B the TV set EN 9 Connections and Setup Better Surround Placem
3. Before moving the unit make sure the disc tray is empty Where the mains plug or an appliance coupler is used as a disconnect device the disconnect device shall remain readily operable Other important use and cleaning information at the end of the booklet EN 5 Connections and Setup Connecting the Antenna FM antenna A FM ANT The FM antenna connects to the FM terminal on the system s back panel It must be hooked up in order to receive clear reception Connecting to your TV Method 1 best HDMI Connect the HDMI OUT jack on the rear of the unit to the HDMI IN jack on your TV using a HDMI cable not included e You can select the resolution of the player s HDMI output signals HDMI Auto 1080p 1080i 720p 480p and 480i to match your TV s resolution capabilities please see instructions on page 21 for details Method 1 To HDMI input HDMI cable not supplied COMPONENT VIDEO OUT To HDMI output HDMI OUT AUDIO OUT Us OUT Notes e Refer to the owner s manual of the connected TV as well e HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC e If your television is a high definition television with an HDMI input we highly recommend you use the unit s HDMI output to get the highest possible video resolution Method 2 good Component video jacks Pr Pb Y The component video jacks are
4. on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet ona circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Ventilation You must adequately ventilate the product Make sure there is adequate space around the unit to provide proper air flow for ventilation See diagram This product complies with DHHS Rules 21 CFR Sub i 7 cm 10 cm 10 cm gt lt gt i 7 cm 10 cm E lt gt chapter J Applicable at the date of manufacture For your Safety The AC power plug is polarized one blade is wider than the other and only fits into AC power outlets one way If the plug won t go into KF the outlet completely turn the plug over and try to insert it the other way If it still won t fit contact a qualified electrician to change the outlet or use a different one Do not at tempt to bypass this safety feature Removing the power plug is the only way to com pletely remove power from your product Make sure the power
5. color coded green blue and red e Additional component video cables not supplied are required They are usually color coded green blue and red Connect the component video OUT jacks on the unit to the component video IN jacks on your TV Method 3 basic Composite video jack yellow This video jack is color coded yellow Use the video cable with yellow plugs supplied for good picture quality Connect the video OUT jack on the unit to the IN jack on your TV VIDEO IN Method 2 y Component Ps VIDEO IN Video Cable Pp not supplied F Method 3 Video Cable included AUDIO OUT Notes If one of the devices is not working check that all the cables have been inserted properly into the jacks If your component has only one input for audio mono connect it to the left white L Mono audio jack on the TV and don t connect the right audio part of the cable EN 6 Connections and Setup Connecting AUDIO IN from External Sources such as TV Method 1 best Using Digital Optical Input Connect components capable of outputting Dolby digital surround sound e g TV or SAT Cable Box or standard PCM stereo format digital signals Use a fiber optical cable for this digital audio con nection Cable not included Press OPTICAL button on remote control or SOURCE button on main unit to select OPTICAL input GAME SAT Cable Box CONSOLE OR OR
6. computer Specification AC power supply AC 120V 60Hz are trademarks Blu ray Disc Blu ray Disc and Netflix is a registered trademark of Netflix Inc Pandora is a registered trademark of Pandora Media Inc PA BDI IVE BD Live and BD Live logo are trademarks of Blu ray Disc Association Manufactured under license Q DOLBY from Dolby Laboratories Dolby TRUE and the double D symbol DIGITAL PLUS are trademarks of Dolby Laboratories Manufactured under license under U S Patent Nos 5 956 674 5 974 380 6 487 535 amp other U S and worldwide patents issued amp pending DTS HD the Symbol amp DTS HD Advanced Digital Out and the Symbol together are registered trademarks amp DTS HD Advanced Digital Out is a trademark of DTS Inc Product includes software DTS Inc All Rights Reserved HDMI the HDMI logo and eo High Definition Multimedia LD Mm J Interface are trademarks or RER registered trademarks of HDMI Licensing LLC Java and all Java based S trademarks and logos are a trademarks or registered ioe trademarks of Oracle America Java Inc in the U S and other POWERED countries EN 28 Additional Information Internet Content and Services Disclaimer All internet content and services accessible through this device belong to third parties and are protected by copyright patent trademark and or other intellectual property laws Such internet cont
7. enter the source selection screen and you can press 4 or W button to choose Optical Disc or USB If you choose Optical Disc option please follow the operation instructions in Playing files on a data disc SS Notes e It is recommended to plug the USB flash drive when the unit is off e It does not support USB hard disc mass storage device multi card reader and other USB computer peripheral e Donot disconnect the USB flash drive when you are playing it it may corrupt the data e If you cannot easily insert the USB device you may have inserted it incorrectly Try to turnover the device and then insert again Watching movies with Netflix Watching Movies with Netflix To use Netflix service connect this player to your network and configure the network settings if they are not finished yet See Network Setting section on page 24 Launching Netflix movie 1 In home menu press 4 or W button to select Connected 2 Press button and then press OK button to enter Creating Netflix account If you are not a Netflix Member Select no Read the instructions displayed on the TV screen and visit http www netflix com from your PC Sign up to create your account then select l m now a member Are you a member of Netflix ES If you are a Netflix Member Select Yes Activating Netflix player To play streaming video via Netflix service Netflix player needs to be activated R
8. in the United States you must first call our Customer Support Center at 1 877 252 6873 during the hours listed in the box below The deternination of service will be made by AVC customer support PLEASE DO NOT RETURN YOUR UNIT TO AVC WITHOUT PRIOR AUTHORIZATION New or remanufactured replacements for defective parts or products will be used for repairs by AVC at its designated Service Center for one year from the defective warranty date Such replacement parts or products are warranted for an additional one year from the date of repair or replacement The Customer will be required to ship the unit to the Service Center indicated at the time Customer Support is contacted to make the necessary repairs The customer is responsible for all transportation charges to the service facility Packaging and Shipping Instruction When you send the product to the AVC service facility you must use the original carton box and packing material or an equivalent as designated by AVC Your Responsibility 1 You must retain your bill of sale to provide proof of purchase 2 These warranties are effective only if the product is purchased and operated in the U S A or Canada 3 Warranties extend only to defects in material or workmanship and do not extend to any product or parts which have been lost or discarded or damage to product or parts caused by misuse accident improper operation or maintenance or use in violation of instructions provided with the produc
9. on your connection environment it may take time to connect to the Internet or the Internet may not be connected IMPORTANT Many BD Live compatible discs require content to be downloaded onto USB flash drive in order to access the available BD Live features A USB flash drive with at least 1GB of free space needs to be inserted prior to inserting the BD Live compatible disc AUX OPTICAL You can connect Audio or Audio Video devices such as a TV Game System VCR Satellite or Cable Box to this unit using the AUDIO IN jacks at the back of the unit The AUX input provides an analog audio connection especially suitable for older devices The OPTICAL input provides a digital audio connection which will allow you to experience true digital surround sound if the connected device is capable of providing Dolby digital surround signals This unit will take the audio from the connected device and play the audio through the speakers Connecting Auxiliary Components Refer to Connecting AUDIO IN from external sources such as TV for details on connecting the auxiliary components to the unit see page7 Selecting AUX OPTICAL Mode Press either the SOURCE button on the main unit or AUX OPTICAL button on the remote control to select AUX or OPTICAL input Sound Output in AUX or OPTICAL Mode You may change the Surround Sound setting to STEREO mode if you like see instructions under Overview of Controls However we recommend you leave t
10. or lower e TV Aspect 16 9 wide 16 9 Pillarbox 4 3 Pan and Scan and 4 3 Letterbox are available for your choice Deep Color This option allows you to turn off the Deep Color color depth setting for video signals output from the HDMI OUT jack Connecting the player to a TV that supports Deep Color allows more accurate color reproduction than when connecting it to a TV that does not support Deep Color It is recommended to set this option Off if the picture is unstable or colors appear unnatural EN 21 The Settings Menu Film Mode Movies are recorded on film at a rate of 24 pictures frames per second Many of the movies on Blu ray discs are recorded on the discs at this frame rate However not all TVs can display 24 progressive frames second of video If the TV cannot display this frame rate you need to turn off Film Mode Note Only your unit s HDMI output supports 1080p video output at any frame rate The component outputs are limited to 1080i regardless of the Film Mode setting ara Setting In the main menu of Settings press button then use amp or W button to select Audio 2 Press button and press A or button to select an option then press OK button 3 Press or W buttons to select the desired option and then press OK button to confirm your selection 4 Press or EXIT button to go to the previous menu PCM Downsampling If you chose to use an external Surround Sound Receiver to
11. play audio via your HDMI connection you can choose a downsampling rate to match the capabilities of your Receiver Notes e The PCM Downsampling and Digital Output settings are only necessary if you don t plan to use you Blu ray Home Theater for playback of audio and instead plan to use an external Audio Receiver for playback of HDMI audio Incorrectly setting the digital audio output s PCM sampling rate too high may result in unpredictable audio playback Digital Output PCM Stereo Sets the HDMI audio format to PCM Stereo this is useful if you have an audio receiver connected that is not a 5 1 channel receiver Bitstream HD Sends the original bitstream from the disc over the HDMI connections using highest quality possible Blu ray audio is limited to the soundtrack for the main movie No PiP audio and no effects audio Bitstream Legacy Sends a DTS or Dolby Digital bitstream from the disc over the HDMI connections Blu ray audio is limited to the soundtrack for the main movie no PIP audio Bitstream Mixed Sends a mixed PIP audio and movie audio DTS audio stream over the HDMI connections This mode is primarily intended for use when you want to hear both PIP audio and the movie audio over an external Audio Receiver PCM 5 1 Sends a PCM audio signal of up to 5 1 channels over the HDMI connection Dynamic Range Control Dynamic Range Control allows you to make the loud parts of
12. plug remains easily accessible Note This unit has been designed to play back BD video with region A and DVD video with region 1 You cannot play back BD video or DVD video that are labeled for other regions Look for the symbols on the right on your BD video or DVD video If these region symbols do not appear on your BD video or DVD video you cannot play back the disc in this unit The letter or number inside the globe refers to region of the world A BD video or DVD video labeled for a specific region can only be played back in the unit with the same region code EN 4 Features e Full high definition video playback at up to 1080p resolution for an amazing viewing experience Upconversion of standard definition DVDs for enhanced picture quality at up to 1080p over an HDMI connection Rich multi channel surround sound Easy and simple HDTV connection using a single HDMI cable cable not included e Multiple outputs for connecting your home theater system or amplifier e PIP functionality that lets you display primary and secondary video at the same time if available on the Blu ray Disc e Pop up menu display without interrupting playback if available on the Blu ray Disc e HDMI 1080p 60fps output Blu ray Disc only that provides smooth playback of video with a frame rate of 60 frames per second TV must be connected with an HDMI cable and be compatible with 1080p 60 frame Connections and Setup What s Inc
13. purpose constitutes or could constitute a violation of copyright law Cleaning Use a soft dry clean cloth Regularly dust the vents at the back or sides e Using solvents abrasive or alcohol based prod ucts risks damaging the unit e If an object or liquid enters inside the unit un plug it immediately and have it checked by an authorized servicer or service center Handling and Caring for Discs e Handle your discs with care Hold the disc with your fingers at the edges or through the hole e Insert the disc with the label facing up for a sin gle sided disc e Place the disc properly into the tray in the allot ted holder Use a soft cloth to clean discs if necessary always wiping from the centre to the edge e Always put discs back in their cases after use and store in a vertical position Do not close the tray with two discs in it or with a disc not sitting correctly in the holder Do not play cracked chipped or warped discs nor try to repair them with adhesive tape or glue Do not write ona disc e Do not move the unit when a disc is being played e Do not scratch discs or store them in places ex posed to direct sunlight high humidity or high temperatures Do not use aerosol cleaners benzene anti static liquids or any other solvent for cleaning discs When cleaning wipe gently with a soft damp water only cloth from the centre to the edge avoiding circular motions which could cause scratch
14. to open the disc tray 3 Place a CD on the disc tray with the label facing up then press amp OPEN CLOSE button to close the disc tray It may take a few seconds for the CD to load 4 After loading a disc playback starts automatically 5 To eject the CD press amp OPEN CLOSE button To control audio CD playback To start playback press button e To pause playback press II button The sound is muted when your unit is in pause mode To resume normal playback press button To stop playback completely press m button To start playback again press button Playback starts at the beginning of the CD e To fast forward press gt button To resume normal playback press button e To fast reverse press lt 4 button To resume normal playback press button e Press either the K or PPI button according to the desired direction Press the K button to skip to the start of the current track or skip to previous tracks Press the gt PI button to skip to the beginning of the next track To select a track press GOTO button once enter the track number with the number buttons then press OK button Playing files on a data disc You can play JPEG files that have been recorded on a CD R or CD RW on this unit Insert a data disc containing picture files A seletion menu appears on the screen F Settings A Connected gt N A FL K v A Pictures Playing files on a data disc To v
15. unit displays audio channel information such as 01 03 Eng Dolby Digital 01 indicates the currently selected audio channel 03 indicates the total number of audio channels Eng English indicates the audio language Dolby Digital describes the currently selected audio format 2 Press button and press or W button to select an audio mode then press OK button Selecting the camera angle Blu ray Disc and DVD disc Some discs offer different camera angles for specific scenes To change the camera angle 1 Press MEM ANGLE button on the remote control The selected angle will be displayed on the display bar at the top of the TV screen 2 Press button and press or W button to select the desired angle then press OK button If the disc was recorded using a single camera angle this function is not available Selecting subtitles You can display subtitles on the TV screen and select a subtitle language from those included on the DVDs 1 Press SUBTITLE button on the remote control The selected language will be displayed on the display bar at the top of the TV screen 2 Press button and press or W button to select your desired language then press OK button PiP Subtitle can be selected through cursor if secondary subtitle is available on the Blu ray Disc EN 15 Playing an audio CD 1 Press ON OFF button on the remote control or ON STANDBY button located on the unit s front panel 2 Press amp OPEN CLOSE button
16. ACE ONLY WITH THE SAME OR EQUIVALENT TYPE WARNING TO BE COMPLETELY DISCONNECT THE POWER INPUT THE MAINS PLUG OF APPARATUS SHALL BE DISCONNECTED FROM THE MAINS THE MAINS PLUG OF APPARATUS SHOULD NOT BE OBSTRUCTED OR SHOULD BE EASILY ACCESSED DURING INTENDED USE Service Information This product should be serviced only by those specially trained in appropriate servicing techniques Main plug is used as the disconnect device it shall remain operable and should not be obstructed during intended use To be completely disconnected the apparatus from supply mains the main plug of the apparatus shall be disconnected from the mains socket outlet completely Caution Invisible laser radiation when open and interlocks defeated Avoid exposure to beam Class 1 laser product This system must be opened only by qualified technicians to prevent accidents caused by the aser beam Copyrights This product incorporates copyright protection technology that is protected by methods claims in certain U S Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited EN 1 Important Information Important Battery Information Do not mix diffe
17. IP address Manual Lets you manually configure network settings such as IP address subnet mask and gateway settings Off Disables the network interface 6 Press or EXIT button to go to the previous menu Network Test Selecting the Network Test will cause the player to attempt to communicate with your home network and if successful with a known internet address If both attempts are successful your network connection should be good If the player can successfully connect to your home network but not to the known internet address your internet service may be down or your security firewall may be blocking access of the player to the internet EN 24 The Settings Menu Quick Setup 1 In the main menu of Settings press button then use A or W button to select Quick Setup and then press OK to confirm 2 Press OK to perform Quick Setup To exit the setup menu Use w button to highlight No thanks I ll go through the full setup menu later and then press OK Or press q button directly 3 Follow the on screen instructions to customize the following settings to your preference Player Menu Settings Resolution TV Aspect 4 After finishing all settings select Exit and press OK to exit the setup Please see page13 for details BD Live 1 In the main menu of Settings press button then use or W button to select BD Live 2 Press button and press A or W butt
18. To pause playing and open a list of scenes Fast reverse play starts OK Allows you to enter or exit trick play mode Trick Play mode allows you to skip to a specific scene in a movie quickly Note Resolution of video streamed from Netflix varies depending on communication speed or bitrate of each content etc Enjoying music with Pandora Pandora is personalized internet radio that is designed to help you discover new music you ll love mixed in with music you already know To use the Pandora service please ensure your unit is successfully connected to a network with internet access See Network Setting section on page 24 For users that already have a Pandora account skip to step 4 Step 1 Creating an activation code on the player a In home menu press or W button to select Connected and then press button to choose Pandora b Select Iam new to Pandora from option list and press OK button c You will be given an activation code then use this activation code to generate a new account on your PC See Step 2 Step 2 Creating a new Pandora account on your PC a Go to http www pandora com rca and enter the activation code b Follow the instructions to create an new account Step 3 Now that you ve successfully created a Pandora account on your PC log in using your player Step 4 Using an existing Pandora account a In home menu press 4 or W button to select Connected an
19. User Manual Manuel de l utilisateur Manual del usuario RTB1016 It s important to read this instruction prior to using your new product for the first time Il est important de lire ce manuel d instructions avant d utiliser votre nouveau produit pour la premi re foi Es importante que lea este libro de instrucciones antes de usar su nuevo producto por primera vez Important Information CAUTION WARNING SHOCK HAZARD no nor open AVIS RISQUE DE CHOC ELECTRIQUE ne pas ouvrr DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE NE PAS EXPOSER CET APPAREIL A DE LA PLUIE OU DE L HUMIDITE SEE MARKING ON BACK OF PRODUCT RISK OF ELECTRIC SHOCK DO NOT OPEN THE LIGHTNING FLASH AND ARROWHEAD WITHIN THE TRIANGLE IS A WARNING SIGN ALERTING YOU OF DANGEROUS VOLTAGE INSIDE THE PRODUCT THE EXCLAMATION POINT WITHIN THE TRI ANGLE IS A WARNING SIGN ALERTING YOU OF IMPORTANT INSTRUCTIONS ACCOMPANYING THE PRODUCT CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SER VICING TO QUALIFIED SERVICE PERSONNEL WARNING TO PREVENT FIRE OR ELECTRICAL SHOCK HAZARD DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE CAUTION USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPL
20. a movie s audio track quieter than they would be in the theatre without making the dialog of the actors any quieter This would be useful for instance when you want to watch a movie in the evening when others might be sleeping Note This setup menu item has no effect unless e You have selected Bitstream Mixed in the Blu ray disc player s audio setup menu When Dynamic Range Control is set to Off movie soundtracks are played with the standard dynamic range When movie soundtracks are played at low volume or from smaller speakers you can set Dynamic Range Control to On Your player applies appropriate compression to make low level content more intelligible and prevent dramatic passages from getting too loud Selecting the Auto option turns on the Dynamic EN 22 The Settings Menu Range Control for all BD movie soundtracks except Dolby TrueHD Stereo Downmix Allows you to downmix the multi channel audio into fewer channels Stereo LoRo Downmixes the multi channel audio into two channel stereo Choose when the Blu ray disc player is connected to the equipment that does not support virtual surround function such as Dolby Pro Logic Surround Encoded LtRt Downmixes the multichannel audio into surround compatible stereo Choose when the Blu ray disc player is connected to the equipment that supports virtual surround function such as Dolby Pro Logic Speaker Setting Once the speaker
21. ard or fast reverse press gt gt fast for ward or lt lt fast reverse e Each time you press one of these buttons the fast forward or fast reverse speed increases from Fast X2 Fast X4 Fast X8 Fast X16 Fast X32 Fast X64 to Fast X128 Press to resume normal play back Changing chapter track e Press either the SKIP K lt or PPI button according to the desired direction Press the SKIP Kd button to skip to the start of the current chapter or skip to previous chapters e Press the SKIP PPI button to skip to the beginning of the next chapter Displaying Blu ray Disc information e Press INFO button your unit displays information about the Disc such as type of disc elapsed time of the current title total time of the current title total number of chapters e Press INFO button again to exit Note The information displayed for discs other than Blu ray Discs will be different EN 14 Special Functions Searching for a title chapter or elapsed time 1 During playback press GOTO button one or more times to select a search mode Press once to select the Goto Title mode e Press twice to select the Goto Chapter mode e Press three times to select the Goto Time mode 2 Press the number buttons to enter the title number chapter number or time then press OK button Your unit goes to the title chapter or time you entered Repeating a title chapter or CD track e Press REPEAT button one or more times to se
22. atch the terminals Connect the speaker wire from the back of each speaker to the corresponding color terminal at the back of the unit Press down the tab to open the terminal and insert the wire Release the tab to lock wire in the terminal Front Speakers Center Speaker 2 Green and Black Purple and Black SR SL SUB 40 30 Subwoofer White and Black gt Insert Oy Press itt S Gray and Black Blue and Black Release Rear Speakers Surround Sound To adjust each speaker volume level for optimum listening experience 1 Press LEVEL button or P on the remote control to select FL front Left speaker 2 Press A or w buttons to adjust the value up or down between 10dB and 10dB 3 Repeat step 1 and 2 for the other speakers FR CT SW SL SR Speaker gains may be set to levels of up to 10dB actual max levels may also depend on your Volume Setting I Note When connecting the speakers make sure the polarities speaker wire to on the receiver of speaker wires and terminals match For example red wire to red terminal on the receiver If the cords are reversed the sound will be distorted Do not let the speaker wires touch each other it will damage the system s amplifier EN 8 Connections and Setup Positioning Speakers 3 6 aa
23. ced at the same time Any battery may leak electrolyte or explode if disposed ofin fire or an attempt is made to charge a battery not intended to be recharged Discard leaky batteries immediately Leaking batteries can cause skin burns or other personal injury When discarding batteries be sure to dispose of them in the proper manner according to your state provincial and local regulations Battery shall not be exposed to excessive heat such as sunshine fire or the like FCC Information This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and
24. d then press button to choose Pandora b Select I have a Pandora account from the option list and press OK button c Sign in with your Pandora account EN 18 Enjoying BD Live Some BD ROMs contains BD Live features that can be downloaded to the external memory local storage for enjoyment In order to access BD Live functions the Blu ray disc player must be properly configured for BD Live internet access and it must be equipped with additional memory USB Flash Drive 1 Insert a USB Flash Drive of at at least 1GB capacity not supplied into the USB jack on the front panel of the Blu ray disc player e The USB device is used as the local storage e Make sure that the USB device is properly inserted into the Blu ray disc player If there is not at least 100Mbyte of free space on the USB device you should choose Erase Blu ray Storage from the BD Live settings see page 25 2 Connect the Blu ray disc player to a network see page 7 3 Turn the Blu ray disc player on 4 Set BD Live Internet Acces to Limit Access or Always Allow Access in BD Live Settings see page 25 5 Insert a BD ROM with BD Live and select the BD Live selection following the instructions on the disc menu e The operation method differs depending on your BD ROM Please refer to the instructions coming with the disc Notes e Do not remove the USB device when using the BD Live function Depending
25. ead the instructions displayed on the TV screen and visit http www netflix com activate on your PC Sign in to your Netflix account if necessary Enter the activation code displayed on the TV screen THT Ga bs peer ee M a gia Ce EN 17 Watching movies with Netflix Preparing Instant Queue To play streaming video via Netflix service Netflix service you must have an appropriate Netflix subscription and the player needs to be registered for Netflix service See previous section for details on how to activate Now you can view Netflix streaming video After having activated Netflix player and prepared Instant Queue movies and TV episodes in your Instant Queue appear on the TV screen Select your desired one using the remote control of the player You can control Netflix streaming video with the following buttons of the remote control of this player gt Play To start playing movie To pause playback while in PLAY mode E Stop To stop playing and return to a list of movie titles II Pause To pause playing movie To start playing while in PAUSE mode D Right To pause playing and open a list of scenes Pressing further proceeds to the next scene q Left To pause playing and open a list of scenes Pressing further proceeds to the previous scene A Up To stop playing and return to a list of movie titles gt gt FWD To pause playing and open a list of scenes Fast forward play starts lt 4 lt REV
26. ent Location If possible place surround speakers to either side of the listening area not behind it Height If space permits install surround speakers 2 3 feet above viewers This helps to minimize localization effects Aiming Aim surround speakers straight across the room not down at viewers to help create a more open spacious surround sound field Alternative Surround Placement Rear wall If rear wall mounting is the only choice aim the speakers at each other A towards the front B or towards the sidewalls C D Experiment with placement until sounds seem to surround you rather than come from behind you No adjacent walls Surround speakers can go on stands facing each other to approximate sidewall mounting A or to the sides or rear of the viewing area aimed upwards they can go right on the floor or preferably a few feet off the floor such as on end tables B Test Tone Channel Balance Channel Balance Your receiver is equipped with a test signal generator to help balance the audio level for each channel see Page 8 for details Level Adjustment and Surround Channel Level Expectation Even though you adjust the surround channel to be as loud as the others on the test signal you may find that surround channels seems quieter for actual TV and Movie content This is because producers use surround for subtle atmospherics and ambience and only rarely for special effects Overview of Cont
27. ent and services are provided solely for your personal noncommercial use and you may not use such content or services in a manner that has not been authorized by the internet content owner or service provider Without limiting the foregoing unless expressly authorized by the applicable internet content owners or service providers you may not modify copy republish upload post transmit translate sell create derivative works exploit or distribute in any manner or medium any content or services displayed through this device THIRD PARTY CONTENT AND SERVICES ARE PROVIDED AS IS AVC MULTIMEDIA IS NOT RESPONSIBLE FOR YOUR USE OF THE INTERNET CONTENT AND SERVICES AND DOES NOT WARRANT SUCH CONTENT OR SERVICES SO PROVIDED EITHER EXPRESSLY OR IMPLIEDLY AVC MULTIMEDIA DOES NOT GUARANTEE THE ACCURACY VALIDITY TIMELINESS LEGALITY OR COMPLETENESS OF ANY INTERNET CONTENT OR SERVICE MADE AVAILABLE THROUGH THIS DEVICE AND UNDER NO CIRCUMSTANCES INCLUDING NEGLIGENCE SHALL AVC MULTIMEDIA BE LIABLE WHETHER IN CONTRACT OR TORT FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES ATTORNEY FEES EXPENSES OR ANY OTHER DAMAGES ARISING OUT OF OR IN CONNECTION WITH ANY INFORMATION CONTAINED IN OR AS A RESULT OF THE USE OF ANY CONTENT OR SERVICES BY YOU OR ANY THIRD PARTY EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Third party content and services may be terminated or interrupted at any time and AVC Multimedia makes no r
28. epresentation or warranty that any content or services will remain available for any period of time Internet content and services are transmitted by third parties by means of networks and transmission facilities over which AVC Multimedia has no control Without limiting the generality of this disclaimer AVC Multimedia expressly disclaims any responsibility or liability for any interruption or suspension of any content or services made available through this device AVC Multimedia is neither responsible nor liable for customer services related to the internet content and services Any question or request should be made directly to the respective internet content and services providers EN 29 Limited Warranty AVC MULTIMEDIA AVC makes the following limited warranty These limited warranties extend to the original consumer purchaser and is limited to non commercial user of the product One Year Parts amp Labor Warranty AVC products purchased in the United States are warranted to be free from defects in materials or workmanship for a period of one year from the date of their original retail purchase If the unit fails to conform to this warranty we will service the product using new or refurbished parts and products at AVC s sole discretion During a period of one year from the effective warranty date AVC will provide when needed service labor to repair a manufacturing defect at its designated Service Center To obtain warranty service
29. es and interference during playback Compatible Formats In order to ensure playback discs must conform with BD DVD or CD standards This unit may not play some recordings or files due to differences in recording formats software used and disc types BD ROM BD ROMs Blu ray Disc Read Only Memory are commercially produced discs and are available in the same capacities as BD below Other than conventional movie and video contents these discs have enhanced features such as interactive content menu operations using pop up menus see below selection of subtitle display and slideshow Although a BD ROM may contain any form of data most BD ROM discs will contain movies in High Definition format for playback on Blu ray Disc players Blu ray Disc BD A disc format developed for recording playing high definition HD video for HDTV etc and for storing large amounts of data A single layer Blu ray Disc holds up to 25 GB and a dual layer Blu ray Disc holds up to 50 GB of data EN 27 Additional Information DVD Video Digital video discs 12 cm single or double sided single or dual layer DVDs are high density optical discs on which high quality picture and audio are recorded by means of digital signals DVD R DVD RW DVD R DVD RW Most DVD R and DVD R one recording only DVD RW and DVD RW discs ze rewritable depending on the DVD writer and discs used Recordings using DVD R and DVD RW discs must be made i
30. es or any state thereof is hereby limited to one year from the date of purchase This limitation does not apply to implied warranties arising under state law This warranty gives you specific legal rights and you may also have other rights which may vary from state to state Some states do not allow limitation on how long an implied warranty lasts when an action may be brought or the exclusion or limitation of incidental or consequential damages so the above provisions may not apply to you For more information on other products and services please contact our web site at www RCAav com Important Also keep your Bill of Sale as proof of purchase Model NO sn ent Product NaMe tennis OR cache aes asec teas secu dacc ces eecee ches caved paee espace eden cate abet calc cancuea tan ccsc dca cedcessacdeceh poses eaccesteaecseenseccereceat Serial NO 2e red anus INVO CE NO Es a hneste Date purchased eee ten Dealer names iseanise FOR SERVICE AND REPAIR PLEASE VISIT WWW RCAav com 2011AVC MULTIMEDIA Need more help Please visit online help at http www RCAav com Specifications and external appearance are subject to change without notice EN 31
31. he system in full surround CH 5 1 mode e If the auxiliary audio signal is mono there will be no output from some speakers in full surround mode Note Optical input cannot decode DTS signals EN 19 Radio This unit has a built in digital tuning FM radio Manual tuning 1 Connect the FM antenna at the back of the unit 2 Press TUNER button 3 Tune a station by pressing TUNE buttons repeatedly until the desired station is found Alternatively you can press and hold the same button down for about two seconds to activate the automatic search function In this mode the unit will automatically tune frequencies until it finds a station 4 Repeat step 3 to tune to another radio station Automatic preset programming 1 Press TUNER button to enter Tuner mode 2 Press and hold TUNER button for two seconds to start automatic preset programming 3 Radio frequencies will be scanned and stored automatically When all the available radio stations are stored or all 30 FM memory locations are full the auto preset programming function will stop Manual preset 1 Tune to a radio station see Manual tuning for details 2 Press MEM ANGLE button While the Program Preset number is still flashing input your desired preset number using the numeric buttons then press MEM ANGLE button to store it Retrieving preset stations 1 Press TUNER button to enter the Tuner mode 2 Press Ked Bi buttons to search up or dow
32. iew JPEG files 1 2 Press 4 or W button to select Pictures then press OK button Press wW or P button to select a file or a folder and press OK or button to start playback If you selected a folder the files in this folder are displayed Press or W button to select a file and press OK or B button to start playback Press W button to return to the Pictures menu Press 4 or W button to select an option then press OK button Settings This option enables you to define Slide Show Effects None Horizontal Scroll Fade and Shutter and Slide Show Delay 5 Seconds 2 Seconds 1 Seconds No Delay 10 Seconds 15 Seconds and 30 Seconds After setting press W to highlight OK and then press OK button to confirm Main Menu Returns to the main menu e Previous folder Returns to the previous folder Start Slide Show This option enables you to view picture files one after another automatically EN 16 Using a USB device Playing USB flash thumb drive Insert a USB thumb drive containing picture into your unit A selection menu appears on the screen 0 0 Settings A i 3 Connected gt N ET F af w e Pictures Press 4 or W button to select Pictures then press OK button To play pictures please see Playing files on a data disc for details If an optical disc containing picture files is inserted at the same time the system will
33. indicated on the disc is selected rare Setting In the main menu of Settings press button then use A or W button to select Display 2 Press button and press A or W button to select an option then press OK button 3 Press or W button to select the desired option and then press OK button to confirm your selection 4 Press or EXIT button to go to the previous menu Resolution You can define the video output resolution in this option HDMI Auto If your TV is a high definition TV HDTV is connected to the HDMI jack on your player and you want your player to set the output resolution based on_ information exchanged between the TV and your player over the HDMI cable 1080p If the TV is a high definition TV HDTV capable of 1080p any frame rate connected to the HDMI jack on your player 1080i If your TV is a high definition TV HDTV capable of 1080i only 720p If your TV is a high definition TV HDTV capable of 720p only 480p If your TV is an enhanced definition TV EDTV 480i If your TV is a standard definition NTSC analog TV Notes Selecting a resolution your TV does not support could result in an unstable picture or loss of the picture See the documentation that came with the TV to find the resolutions the TV supports Only the HDMI output on your unit supports 1080p video output at any frame rate If the TV is connected to the component output the video output is limited to 1080i
34. lect a repeat mode Using PiP picture in picture mode Some Blu ray Discs are compatible with picture in picture PiP mode In PiP mode the primary video is displayed on the full screen and the secondary video is displayed in a small window Primary video Secondary video F e Press PiP button to turn PiP mode on or off e Press AUDIO or SUBTITLE button to turn the audio subtitle for the video in the PiP window on or off Then use cursor buttons and OK button to select your preferred options Notes e The available options of Audio vary from different disc format e PiP Subtitle is not available for all discs It only applies to Blu ray discs that supports picture in picture features Some discs allow you to turn PiP on off only via the disc menu Using a disc popup menu 1 During Blu ray or DVD playback press POP UP button The Blu ray popup menu or the title menu of DVD disc opens 2 Press A W or buttons to select an option then press OK button Selecting a play source e Press SOURCE button on the front panel of the unit repeatedly to select BD USB OPTICAL AUX TUNER e Press BD USB button on the remote control to select BD USB mode e Press OPTICAL button on the remote control to select OPTICAL mode e Press AUX button on the remote control to select AUX mode e Press TUNER button on the remote control to select TUNER mode Selecting the audio mode 1 Press AUDIO button Your
35. luded O O O CO 0000 oo 000 O0000 0 0 000000 00000 0000 0000 CES Remote control and 2 Left and right front Subwoofer Left and right Sur Center speaker AAA batteries speakers round speakers a One Pig Tail Composite Main unit receiver antenna wire video cable Things to Consider before You Connect e Ensure that the mains AC power supply in your house complies with that indicated on the identification sticker located on the back of your unit Install your unit horizontally away from any source of heat fireplace or appliances creating strong magnetic or electric fields The components of this unit are sensitive to heat The maximum ambient temperature should not exceed 35 C 95 F e Leave enough space around the unit to allow adequate ventilation 10 cm 4 inches on either side and above the top and 5 cm 2 inches at the rear The humidity of the room should not exceed 75 If you have to use the unit outdoors do not expose it to rain or splashing water The apparatus should not be exposed to dripping or splashing and no objects filled with liquids such as vases should be placed on the apparatus Moving the unit from a cold place to a warm one can cause condensation on some components inside the unit Let the condensation disappear on its own before turning the unit on again
36. m gt Zz Q m 0 0 O D D D AUX OPTICAL TUNER D 0 0 D vo Blu ray Disc wk Note Insert the two AAA includ ed with this unit batteries into the remote control prior to use SETUP PiP AUDIO SURROUND SUBWOOFER MENU SUBTITLE AUX OPTICAL TUNER BD USB Press to access the Dimmer DIM Sleep SLP and test tone setting the settings will be shown of the unit s front panel display Dimmer Setup To adjust the brightness of display on front of Blu ray disc player Press SETUP button and the DIM 0 appears then use amp W buttons to select DIM 0 DIM 1 or DIM 2 Sleep Setup Press SETUP button and the DIM 0 appears Use 4 gt buttons to select SLP OFF then press the amp w buttons select 30M 60M 90M or 120M The unit will automatically turn off once it counts down the sleep time Test Tone Press SETUP button and the DIM 0 appears Use q gt buttons to select TEST OFF then press amp w buttons to select FL front left speaker FR front right speaker CT center speaker SW subwoofer SL surround left speaker or SR surround right speaker then press OK button You ll hear a test tone coming from the speaker you select Press EXIT button to exit this function To adjust the speaker volume levels press LEVEL button and use buttons to select the speaker you are testing then use 4 or W buttons to adjust
37. n Video DVD mode Recordings using DVD RW discs must be made in accordance with the specifications for DVD RW discs with a 4 7 GB capacity Audio CDs Audio CDs 12 cm CD R CD RW Most CD R one recording only and CD RW discs rewritable CD Rs written during a multisession recording can be played provided that the session has ended before the disc is played depending on the write software However depending on the condition of the CD writer computer and the disc used you may find that not all discs will play When playing a CD R disc it is normal for the unit to take up to 60 seconds to recognize the disc before starting to play If the disc is not recognized after a period of 120 seconds remove the disc and insert it again Do not use its full capacity e CD Rs should be preferably used instead of CD RWs rewritable CDs as in certain cases CD RW playback may be faulty Use reliable good quality CD write software e Close all other ahpplications on the computer to ensure reliable CD R disc recording JPEG Files CD R and CD RW with JPEG files Certain JPEG files including progressive JPEG files cannot be read by this unit The total number of files and folders on the disc should be less than 650 Make sure that files have the jpg extension Files without the jpg exten sion will not be able to be read by the unit even thought the files are shown as JPEG images on your
38. n for the preset stations or directly press the numeric buttons EN 20 Tips When a strong FM signal is tuned ST is displayed If there is any interference change the an tenna s position until ideal sound recep tion is obtained TV and other electronic devices could be the cause of interfer ence so try to position the antenna away from them A weak signal can affect the Automatic preset programming function s efficien cy Adjust the antenna for better reception and amore efficient search The Settings Menu The Settings menu appears automatically when the unit is in BD USB stop mode Use amp or W button to select Settings Info 00 Quick Setup W BD Live A 00 Settings gt v L A Dispaly Audio x Connected Speaker Language Language Setting 1 In the main menu of Settings press button then use amp or W button to select Language 2 Press button and press A or W button to select an option then press OK button 3 Press A or W button to select the language you want then press OK button to confirm your selection 4 Press or EXIT button to go to the previous menu Notes If the selected language is not available on a disc the disc s language will be used instead e If the language chosen is available it is automatically selected when you display the subtitles or press SUBTITLE button on the remote control Otherwise the subtitle language
39. nit on the TV Replace the HDMI cable with a better one A bad HDMI cable can cause loss of video The picture is of poor quality with snow or lines e Check the connections There is no sound or the sound is of poor quality e Check the connections e Make sure the speakers are connected e Make sure the MUTE function is not on No surround sound Check to see if system is actually in full Surround mode see Audio setting amp Speaker setting on page 22 23 For AUX TUNER OPTICAL mode press the SURROUND button on the remote control the front panel display should indicate the current setting STEREO or CH 5 1 If current setting is STEREO the surround speakers and center speaker will be inactive Press amp W button to change surround mode from STEREO Note Not all discs media files or audio sources provide surround audio thus lack of audio to surround speakers may be due to the actual source being played I can t find my file in the JPEG listing e Make sure the file name is valid The remote control does not work or works only intermittently e Check that batteries are inserted or change them e Aim the remote control at the unit The infrared beam must not be blocked or interrupted e Check that the remote control is configured to control the device you are trying to operate with it The subtitles do not appear e Check that the BD DVD disc provides subtitles e Refer to the section on how
40. on to select an option then press OK button 3 Press 4 or W buttons to select the desired option and then press OK button to confirm your selection 4 Press or EXIT button to go to the previous menu BD Live Internet Access e Limit Access Allows Internet access with valid BDLive network access approval Always Allow Access Always allows BD Live Internet access Prohibit Access Never allows BD Live Internet access BD Live Storage The available storage space is displayed next to BD Live Storage Erase Blu ray Storage If you choose OK to erase Blu ray storage all bookmarks and BD Live content saved in memory will be deleted Troubleshooting The unit does not switch on e Make sure it is plugged in e Press ON OFF button on the remote control or ON STANDBY button on the front of the unit The device switches off spontaneously To save power the device switches off automati cally when it is not being used for more than 30 minutes Switch it on again e Ifthe SLEEP SETUP see page 12 for details is set to 30 60 90 120 minutes the device will turn off automatically once it counts down the sleep time If Auto Power Down in System settings is set to 30 45 60 minutes the device will switch off automatically if it remains idle and no activi ties are made Switch it on again Blu ray Disc or DVD does not play Make sure that the disc has the correct region code Some Blu
41. ontains a low power laser device EN 2 Important Safety Instructions Please Read and Save for Future Reference Additional Safety Information Some of the following information may not apply to your particular product however as with any electronic product precautions should be observed during handling and use e Read these instructions e Keep these instructions e Heed all warnings e Follow all instructions e Do not use this apparatus near water e Clean only with a dry cloth e Do not block any ventilation openings Install in accordance with the manufacturer s instructions e Do not install near any heat sources such as radiators heat registers stoves or other apparatus Including amplifiers that produce heat The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus Always leave sufficient space around the product for ventilation Do not place productin oronabed rug in a bookcase or cabinet that may prevent air flow through vent openings Donotplace lighted candles cigarettes cigars etc on the product Connect power cord only to AC power source as marked on the product Care should be taken so that objects do not fall into the product Do not attempt to disassemble the cabinet This product does not contain customer serviceable components e Only use attachments accessories specified by f yo
42. ray discs will only play over an HDMI connection It might be impossible to read the disc e Insert the disc with the printed side facing up e Check that the disc can actually be played by this device e Clean the disc Picture in Picture PiP does not work on a Blu ray Disc e Make sure that the disc supports PiP mode When playing a BD Live disc the screen is black e Erase BD Storage Make sure that the internet connection is work ing Make sure that the internet cable is connected securely and correctly to the unit and the internet jack Some discs require an Internet connection to play Cannot connect to the internet e Make sure that the Internet connection is set up correctly e Test the Internet connection to make sure that it is working e Make sure that the BD Live Internet Access op tion is not set to Prohibit Access Make sure that the disc your are playing is a legal copy EN 25 Troubleshooting After connecting to the Internet cannot down load a file e Erase BD Storage e Make sure that the internet connection is work ing e Try a different USB flash drive File was downloaded but playback from file pauses e Make sure that the USB flash drive is a USB 2 0 de vice Using a USB1 1 device may cause pausing e Try a different USB flash drive There is no picture e Check that the TV is operating correctly e Check the connections e Select the AV input assigned to the u
43. rent types of batteries or new and old batteries Do not use rechargeable batteries In order to avoid any risk of explosion observe the polarities indicated inside the battery compartment Replace only with the type of batteries specified Do not dispose of them in a fire or recharge them If you are not using the remote control for a long period of time remove the batteries Please respect the environment and prevailing regulations Before you dis pose of batteries or accumulators ask your dealer whether they are subject to special recycling and if they will ac cept them for disposal Illustrations contained in this document are for rep resentation only CLASS 1 LASER PRODUCT APPAREIL A LASER DE CLASSE 1 PRODUCTO LASER DE CLASE 1 CAUTION This product utilizes a laser Use of controls or adjustments or performance of procedures other than those specified may result in hazardous radiation exposure Do not open covers and do not repair yourself Refer servicing to qualified personnel This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme du NMB 003 du Cana da WARNING To reduce the risk of fire or electric shock do not expose this product to rain or mois ture No objects filled with liquids such as vases should be placed on the apparatus Double insulation when servicing use only identical replacement parts This product c
44. ress OK The display for Player Menu Settings selection appears Next Return 2 Press amp or W button to select English French or Spanish and press OK 3 Press W button to select Next and press OK then the display for Resolution selection appears Next Return 4 Press amp or W button to select HDMI Auto 1080p 1080i 720p 480p or 480i and press OK For details about the Resolution please see page 21 5 Press W button to select Next and press OK then the display for TV Aspect selection appears Next Return 6 Press amp or W button to select 16 9 Wide 16 9 Pillarbox 4 3 Pan and Scan or 4 3 Letterbox and press OK For details about the TV Aspect please see page 21 7 Press W button to select Next and press OK The display for Quick Setup complete appears and press OK to exit the setup Notes e You can restore the settings to the factory settings see page 24 e You can run Quick Setup again from Quick Setup in Settings see page 25 EN 13 Playing a Blu ray Disc or DVD Regional Coding This unit has been designed to play back BD video encoded for region A and DVD video encoded for region 1 You cannot play back BD video or DVD video that are labeled for other regions Look for the symbols on the right on your BD video or DVD video If these region symbols do not appear on your BD video or DVD video you cannot play back the disc in thi
45. rols Front Panel Controls Press to open or close the disc tray Switch the unit Adjust the on and off volume Start pause playback Connect a USB flash drive to this port Select the input sources Press repeatedly to select BD USB OPTICAL AUX TUNER EN 10 Overview of Controls mn OPEN CLOSE SELLE VE Cc m X 6 Be m gt Zz Q m 0 0 O D D D AUX OPTICAL TUNER D 0 0 D vo Blu ray Disc ON OFF OPEN CLOSE R red G green B blue Y yellow Numbers CLEAR GOTO VOL MUTE POP UP SKIP p gt i lt lt A UTUNE gt TUNE v OK EXIT REV FWD STOP PLAY STEP II LEVEL INFO MEM ANGLE ZOOM REPEAT A B Press to turn on your unit or put your unit in standby mode When your unit is in standby mode power is still entering your unit To disconnect power unplug the power cord Press to open or close the disc tray When playing a Blu ray Disc that has a Java application press to control playback For more information see the documentation that came with the Blu ray Disc In playback mode press GOTO button then press the number buttons to enter a title chapter track or time Press to clear an input Press to search for a title chapter track or time Press to increase or decrease the volume Press to turn off sound Press again
46. ry Defaults If you choose Ok in the prompt message box and press OK button all settings will be restored to the factory defaults Deactivate Netflix If you choose Ok in the prompt message box and press OK button Netflix will be deactivated Deactivate Pandora If you choose Ok in the prompt message box and press OK button the unit will then cease to automatically log in to Pandora using your Pandora password Update Via Network This option allows to update your product software via the internet Info Setting 1 In the main menu of Settings press button then use or W button to select Info 2 Press button to display the related information Network Setting 1 In the main menu of Settings press P button then use amp or W button to select Network 2 Press button 3 Press 4 or W button to select Wired then press OK button The IP Settings screen appears If the network connection is active Link Up appears next to Link Status If the network connection is not active Link Down displays next to Link Status 4 Press A or W button to select IP Mode then press OK button IP Settings Link Status gt Link Down MAC Address IP Mode gt Dynamic IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Gateway 0 0 0 0 Primary DNS 0 0 0 0 Secondary DNS 0 0 0 0 XX XX XX XX XX XX Apply Cancel 5 Press 4 or W button to select an IP Mode You can select Dynamic Uses DHCP to automatically obtain an
47. s are connected to the system you can set the speakers to obtain the best possible surround sound 1 In the main menu of Settings press button then use amp or W button to select Speaker then press OK 2 Use A W or to highlight the desired speaker then press OK 3 Press A or W to select the desired audio signal and then press OK to confirm 4 Press or EXIT to go to the previous menu Note Setting a speaker to Off will result in no sound being delivered to this speaker We highly recommend you leave all speakers set to On EN 23 The Settings Menu System Setting 1 In the main menu of Settings press P button then use or W button to select System 2 Press button and press A or W button to select an option then press OK button 3 Press 4 or W buttons to select the desired option and then press OK button to confirm your selection 4 Press or EXIT button to go to the previous menu Optical Disc AutoPlay If On is selected the player will play a disc automatically when the unit is turned on or if you press the BD USB button Screen Saver Duration This Blu ray disc player has a screen saver feature when your player is inactive You can set the interval time you want your player to wait before activating the screen saver Auto Power Down This power saving option defines the time duration upon which the unit shuts down automatically as a result of inactivity Restore Facto
48. s unit The letter or number inside the globe refers to region of the world A BD video or DVD video labeled for a specific region can only be played back in the unit with the same region code Basic playback Blu ray Disc or DVD 1 Turn on your television set 2 Press ON OFF button on the remote control or ON STANDBY button located on the unit s front panel Press BD USB button on the remote control 3 Press amp OPEN CLOSE button to open the disc tray 4 Place a disc onto the disc tray with the label side up 5 Press amp OPEN CLOSE button again to close the disc tray 6 After loading a disc playback starts automatically orthe disc menu appears If the disc menu appears select the Play option and press OK button to begin playback if Optical Disc AutoPlay is set on see page24 Playback To start playback press button Pause To pause playback press II button To resume normal playback press button Frame advance e Press PAUSE II twice Step Fwd is displayed e Each time you press PAUSE button the picture advances one frame Press B to resume normal playback Stop e To stop playback press m button The Settings menu is displayed To resume playback press on the remote con trol or press amp or W button to select DVD BD ROM then press OK button Depending on the disc playback starts where it stopped or at the beginning of the disc Accelerated play e To fast forw
49. t or to product which has been altered or modified without authorization of AVC or to products or parts thereof which have had the serial number removed or changed Out of Warranty In the event your product requires repair after the limited warranty period has expired please contact our Customer Support Center at 877 252 6873 or www RCAav com Hours Monday Thursday 9am 7pm Friday 9am 5pm Saturday 9am NOON Eastern time Important You are responsible for any transportation shipping or insurance relative to the return of the product to our Product Returns Center EN 30 Limited Warranty All warranties implied by state law including the implied warranties of merchantability and fitness for a particular purpose are expressly limited to the duration of the limited warranties set forth above With the exception of any warranties implied by state law as hereby limited the foregoing warranty is exclusive and in lieu of all other warranties guarantees agreements and similar obligations of manufacturer or seller with respect to the repair or replacement of any parts In no event shall AVC be liable for consequential or incidental damages No person agent distributor dealer or company is authorized to change modify or extend the terms of these warranties in any manner whatsoever The time within action must be commenced to enforce any obligation of AVC arising under the warranty or under any statute or law of the United Stat
50. the value up or down between 10dB and 10dB Press to turn PiP picture in picture mode on or off This function is only available by Blu ray discs if available on disc Accesses the audio function PiP Audio can be selected through cursor if secondary Audio is available on the Blu ray Disc In AUX OPTICAL TUNER mode press to show current sound mode CH 5 10r STEREO on the front of Blu ray disc player display To change the current setting first press the SURROUND button then use 4 buttons on the remote control to select STEREO or CH5 1 Press to display current Subwoofer setting SOFT PWRFUL STRONG BALANCE To change settings first press to access the current Subwoofer setting then use 44 W buttons on theremote control to change the current setting Accesses the disc menu during playback on DVD Accesses the subtitle function PiP Subtitle can be selected through cursor if secondary subtitle is available on the Blu ray Disc Press to select AUX input source Press to select OPTICAL input source Press to select TUNER mode FM radio Press to select the BD USB mode EN 12 Quick Setup When turned on for the first time or after resetting it to the factory default the Quick Setup menu will pop up as following Yes No Follow the below steps to make the basic settings for using the Blu ray player 1 Press OK to perform Quick Setup To exit Quick Setup press button to select No and then p
51. to display subtitles The disc menu language is not the correct one The disc menu language has not been set up e The language of your choice is not available on the disc EN 26 Additional Information Precautions Use e If your unit has been stored in a cool place for any length of time during a journey for example wait for about 2 hours before using it The openings located on the top and bottom are for ventilation and must not be obstructed During thunderstorms we recommend that you isolate the unit from the electrical supply so that itis not damaged by electrical or electromagnetic surges e This unit is designed for continuous use Switching off the unit to standby mode does not disconnect it from the mains supply To completely isolate the equipment remove the plug from the mains jack as some components remain connected to the electrical supply e If you notice any burning or smoke disconnect the unit immediately to avoid any risk of electrocution Donot attempt to look inside the unit through the disk tray opening or any other opening You may be electrocuted or exposed to laser radiation e This unit is for domestic use only and must not be used for industrial purposes e Total or partial copying of recordings protected by copyrightlegislation withoutthe explicit permission of the holder of the rights contravenes current legislation Copying or downloading music files for sale or any other business
52. to turn the sound back on During Blu ray Disc playback press to open a menu that lets you control Blu ray Disc playback During DVD playback press to open the DVD title menu if available Press to go to the next or previous chapter Blu ray Disc DVD or track CD In tuner mode press to go to the next higher lower preset station Navigate through the menus The left and right arrows also tune the radio frequency in the tuner mode Confirms your selection Press to return to the previous menu When in a Menu or file browser window you can press this button to move you back to a previous menu level or folder level Press to fast reverse Press to fast forward Press to stop playback Press to start or resume playback Press once to pause playback Press twice then each time you press this button the picture advances one frame Toggle channels for different level settings Adjusts the value using A or w Accesses the Info menu Stores a station in tuner mode Accesses the camera angle function for Blu ray or DVD discs if available Press to zoom in on the video Each time you press this button the magnification level changes This button is only used for DVD discs Press to repeat the current title chapter track or repeat all Performs point to point repeat playback on DVD EN 11 Overview of Controls mn OPEN CLOSE SELLE UE m OF X p iF
53. ur product operates on batteries adhere to the the manufacturer following precautions e Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has A two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third B prong is provided for your safety If the provided plug does not fit into your wall outlet consult an electrician for replacement of the obsolete outlet C e Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus e Unplug this apparatus during lightning storms or when unused for long periods of time e Use only with a cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart ANa apparatus combination to avoid Portable Cart injury from tip over Warning e Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as the power cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped EN 3 Any battery may leak electrolyte if mixed with a different battery type if inserted incorrectly or if all batteries are not repla
Download Pdf Manuals
Related Search