Manual - Ross Video
Contents
1. Ross Video Limited SEA 8008 Serial Equalizing Amplifier User Manual E 5 o e que a ZA o o Seo dudo o o ET A mea ve L El o gt elo ISE OR PRO DME SUE EEG as 111111111111111 ILYJANI NON dNY 03 RES 221 B008A 001MISS SH o ROSS Ross Part Number 8008DR 004 Issue OSA Cool Practical Technology SEA 8008 e Serial Equalizing Amplifier User Manual e Ross Part Number 8008DR 004 e Document Issue 05A e Release Date November 22 2005 Printed in Canada The information contained in this User Manual is subject to change without notice or obligation Copyright O 2005 Ross Video Limited All rights reserved Contents of this publication may not be reproduced in any form without the written permission of Ross Video Limited Reproduction or reverse engineering of copyrighted software is prohibited Notice The material in this manual is furnished for informational use only It is subject to change without notice and should not be construed as a commitment by Ross Video Limited Ross Video Limited assumes no responsibility or liability for errors or inaccuracies that may appear in this manual Trademarks ROSS is a registered trademark of Ross Video Limited e Ross ROSS ROSS and MLE are registered trademarks of Ross Video Limited e All other product names and any registered and unregistered trademarks mentioned in this manual are used for identification purposes only and remai2. SEA 8008 User Manual Iss 05A Installation and Setup e 2 1 Board Installation Use the following steps to install the SEA 8008 in a RossGear 8000 series digital distribution frame 1 Refer to the User Manual of the RossGear 8000 series frame to ensure that the frame is properly installed according to instructions If this module is to be installed in any compatible frame other than a Ross Video product refer to the frame manufacturer s manual for specific instructions 2 Please note that heat and power distribution requirements within a frame may dictate specific slot placement of cards Cards with many heat producing components should be arranged to avoid areas of excess heat build up particularly in frames using convectional cooling 3 After selecting the desired frame installation slot hold the SEA 8008 card by the edges and carefully align the card edges with the slots in the frame Then fully insert the card into the frame until the rear connection plug is properly seated BNC Labels Affix the supplied BNC label as per the included instructions to the BNC area on the rear of the rack frame Cable Connections This section provides instructions for connecting cables to the SEA 8008 when mounted in RossGear 8000 series Digital Products Frames The cable connectors on the rear of the frame are marked for distribution amplifiers having one input and eight outputs The SEA 8008 cable connections match the frame designatio
3. 143Mb s up to and including 360Mb s All eight outputs are non inverting and so they can be used for the distribution of DVB ASI signals as well as SMPTE 259M signals The SEA 8008 is designed to operate within the RossGear 8000 series digital products frame Ten amplifiers can be installed in a Ross 2 rack unit frame and four amplifiers in a Ross 1 rack unit frame This amplifier also fits Leitch 6800 series frames Functional Block Diagram SERIAL IN SERIAL OUT EQUALIZER Figure 1 Simplified Block Diagram of SEA 8008 Functions Leitch is a trademark of Leitch Technology Corporation 1 2 e Introduction SEA 8008 User Manual Iss 05A Features The following features make the SEA 8008 the best solution for general SDI equalizing and distribution Accommodates SMPTE 259M and DVB ASI signals from 143 Mb s to 360Mb s Automatic cable equalization to 305m 1000 ft Input signal present indicator Output waveform reshaping 8 Non inverted Serial Digital Outputs Low cost Fault Reporting SMPTE 269M 5 year transferable warranty Documentation Terms The following terms are used throughout this guide SEA 8008 User Manual Iss 05A Frame refers to the DFR 8104A and DFR 8110A frames that house the SEA 8008 card All references to the DFR 8104A and DFR 8110A also include the DFR 8104A C and DFR 8110A C versions with the cooling fan option See the respective User Manuals for details Operator
4. Frame and Power Supply PS 8102 2RU holds 10 modules includes 1 power supply e DFR 8110A C Digital Products Frame with Cooling Fan Module and Power Supply PS 8102 2RU holds 10 modules includes 1 power supply Your SEA 8008 Serial Equalizing Amplifier is a part of the RossGear family of products Ross Video offers a full line of RossGEAR terminal equipment including distribution conversion monitoring synchronizers encoders decoders keyers switches as well as analog audio and video products SEA 8008 User Manual Iss 05A Ordering Information e 6 1 Contact Us Contact our friendly and professional support representatives for the following e Name and address of your local dealer e Product information and pricing e Technical support e Upcoming trade show information General Business Office and Technical Support PHONE After hours Emergency Fax E MAIL General Information Technical Support Ross Video Limited POSTAL SERVICE Ross Video Incorporated Visit Us Please visit us at our website for e Company information 613 e 652 e 4886 613 e 652 e 4886 ext 333 613 e 652 e 4425 solutions rossvideo com techsupport rossvideo com 8 John Street Iroquois Ontario Canada KOE 1K0 P O Box 880 Ogdensburg New York USA 13669 0880 e Related products and full product lines e On line catalog e Trade show information e News e Testimonials WI Age sisvideo com
5. C Notices US FCC Part 15 This equipment has been tested and found to comply with the limits for a class A Digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to correct the interference at their own expense Changes or modifications to this equipment not expressly approved by Ross Video Ltd could void the user s authority to operate this equipment Notice CANADA This Class A digital apparatus complies with Canadian ICES 003 Cet appareil numerique de classe A est conforme a la norme NMB 003 du Canada EUROPE This equipment is in compliance with the essential requirements and other relevant provisions of CE Directive 93 68 EEC INTERNATIONAL This equipment has been tested to CISPR 22 1997 along with amendments A1 2000 and A2 2002 and found to comply with the limits for a Class A Digital device This is a Class A product In domestic environments this product may cause radio interference in which case the user may have to take adequate measures Noti
6. Th This Chapter cia da ace A Word of ThankKS ooooccoonnnocncnonnnonnnononoconnncnnnoconanos O VI Wii ei ns Functional Block Diagram oooonconnnncnionnocnconncnnnonnos A A Pla Sloan tots ORE DE ETE Documentation Terms ocoooocconononnncconnnonnncconnconnnccnnoss Installation and Setup In This Chapter dd a Static DISChar Pei Unpacking and adds Fault Reporting Setup Board Installation eee SMPTE 269M Fault Reporting In This Chapter e canon T Overview cocccoonnoconcnonnncnnononnnccnnnnnnn ccoo nnnnnn cnc nnnnnnnccn oros Jumper SETUP ri aunts Frame Connections ocooocoooncconnnoonncconnnonnncconnnonnnccnnoos Dita a od Specifications In This Chapter ad ohne anion ns Technical Specifications cccesceeseesecsteesseeseeenes Service Information In This Chapter A E T T T Troubleshooting Checklist Warranty and Repair Policy sesser Ordering Information H This Chapter iia SEA 8008 and Related Products SEA 8008 User Manual Iss 05A Contents e i ii e Contents SEA 8008 User Manual Iss 05A Introduction In This Chapter This chapter contains the following information sections e A Word of Thanks e Overview e Functional Block Diagram e Features e Documentation Terms A Word of Thanks Congratulations on choosing the Ross Video SEA 8008 Serial Equalizing Amplifier The SEA 8008 is part of a full line of Digital Products within the RossGear Termin
7. al Equipment family of products backed by Ross Video s experience in engineering and design expertise since 1974 You will be pleased at how easily your new SEA 8008 fits into your overall working environment Equally pleasing is the product quality reliability and functionality Thank you for joining the group of worldwide satisfied Ross Video customers Should you have a question pertaining to the installation or operation of your SEA 8008 please contact us at the numbers listed on the back cover of this manual Our technical support staff is always available for consultation training or service SEA 8008 User Manual Iss 05A Introduction e 1 1 Overview The SEA 8008 Serial Equalizing Amplifier is designed for general SDI equalizing and distribution use where the outputs must all be non inverted It suits applications where multiple outputs are required but where reclocking is not required Although the amplifier automatically equalizes up to 305m 1000 ft of Belden 8281 input cable at 270Mb s 200m 656 ft is the recommended limit due to jitter considerations Special measures have been taken to ensure excellent return loss on both input and outputs This design guarantees error free performance even with short cable runs A very useful feature of the SEA 8008 is the card edge LED status indicators which confirm the presence of an input signal capable of equalization The SEA 8008 operates on all serial digital standards from
8. and User both refer to the person who uses the SEA 8008 Board Card and Module all refer to the SEA 8008 module itself including all components and switches System and Video system refers to the mix of interconnected production and terminal equipment in which the SEA 8008 operates Introduction e 1 3 1 4 e Introduction SEA 8008 User Manual Iss 05A Installation and Setup In This Chapter This chapter contains the following information sections Static Discharge Unpacking Fault Reporting Setup Board Installation BNC Labels Cable Connections LEDs Static Discharge Whenever handling the SEA 8008 and other related equipment please observe all static discharge precautions as described in the following note Static discharge can cause serious damage to sensitive semiconductor devices Avoid handling circuit boards in high ad AA static environments such as carpeted areas and when wearing ESD synthetic fiber clothing Always exercise proper grounding Susceptibility precautions when working on circuit boards and related equipment Unpacking Unpack each SEA 8008 you received from the shipping container and check the contents against the packing list to ensure that all items are included Ifany items are missing or damaged contact your sales representative or Ross Video directly Fault Reporting Setup See Chapter 3 SMPTE 269M Fault Reporting for complete details
9. ce Maintenance User Serviceable Parts Routine maintenance to this RossGear product is not required This product contains no user serviceable parts If the module does not appear to be working properly please contact Technical Support using the numbers listed under the Contact Us section on the last page of this manual All RossGear products are covered by a generous 5 year warranty and will be repaired without charge for materials or labor within this period See the Warranty and Repair Policy section in this manual for details Environmental Information The equipment that you purchased required the extraction and use of natural resources for its production It may contain hazardous substances that could impact health and the environment To avoid the potential release of those substances into the environment and to diminish the need for the extraction of natural resources Ross Video encourages you to use the appropriate take back systems These systems will reuse or recycle most of the materials from your end of life equipment in an environmentally friendly and health conscious manner The crossed out wheeled bin symbol invites you to use these systems If you need more information on the collection reuse and recycling systems please contact your local or regional waste administration Y ou can also contact Ross Video for more information on the environmental performances of our products eS Contents Introduction
10. erforming a quick visual check may reveal many problems such as connectors not properly seated or loose cables Check the module the frame and any associated peripheral equipment for signs of trouble Power Check Check the power indicator LED on the distribution frame front panel for the presence of power If the power LED is not illuminated verify that the power cable is connected to a power source and that power is available at the power main Confirm that the power supplies are fully seated in their slots If the power LED is still not illuminated replace the power supply with one that is verified to work Reseat the Card in the Frame Eject the card and reinsert it in the frame Check Control Settings Refer to the Installation and Operation sections of the manual and verify all user adjustable component settings Input Signal Status Verify that source equipment is operating correctly and that a valid signal is being supplied Output Signal Path Verify that destination equipment is operating correctly and receiving a valid signal Module Exchange Exchanging a suspect module with a module that is known to be working correctly is an efficient method for localizing problems to individual modules Service Information e 5 1 Warranty and Repair Policy The RossGear SEA 8008 is warranted to be free of any defect with respect to performance quality reliability and workmanship for a period of FIVE 5 years from
11. n the exclusive property of their respective owners Important Regulatory and Safety Notices Before using this product and any associated equipment refer to the Important Safety Instructions gt listed below so as to avoid personnel injury and to prevent product damage Products may require specific equipment and or installation procedures be carried out to satisfy certain regulatory compliance requirements Notices have been included in this publication to call attention to these Specific requirements Symbol Meanings e Warning gt O D O 5 gt Z O a O O gt Susceptibility This symbol on the equipment refers you to important operating and maintenance servicing instructions within the Product Manual Documentation Failure to heed this information may present a major risk of damage or injury to persons or equipment The symbol with the word Warning within the equipment manual indicates a potentially hazardous situation which if not avoided could result in death or serious Injury The symbol with the word Caution within the equipment manual indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury It may also be used to alert against unsafe practices The symbol with the word Notice within the equipment manual indicates a situation which if not avoided may result in major or minor equipment damage or a situati
12. ns Connect the input and output cables according to the frame rear panel connections diagram in the following figures The inputs are internally terminated in 75 ohms It is not necessary to terminate unused outputs SDI In SDI Out 2 SDI Out 1 SDI Out 4 SDI Out 3 SDI Out 6 SDI Out 5 SDI Out 8 SDI Out 7 Figure 2 BNC designations for RossGear DFR 8110A 2RU frame 2 2 e Installation and Setup SEA 8008 User Manual Iss 05A LEDs The front edge of the module has two LED indicators which show the status of the amplifier They are described in the following figure and table INPUT OK LED lt ERROR LED Figure 3 LEDs Table 1 LED Status Indicator Descriptions When lit the module is operating correctly This indicates that the INPUT OK Green input signal is suitable for achieving error free performance and is within the capability of the cable equalizer to restore the signal When lit the input signal is too low or absent In some circumstances the signal may still be restored correctly but the ERROR Bee circuits will be working close to the limit of their capability and reliability cannot be assured SEA 8008 User Manual Iss 05A Installation and Setup e 2 3 2 4 e Installation and Setup SEA 8008 User Manual Iss 05A SMPTE 269M Fault Reporting In This Chapter This chapter contains the following sections e Overview e Jumper Setup e Frame Connections e Detail
13. on which could place the equipment in a non compliant operating state This symbol is used to alert the user that an electrical or electronic device or assembly is susceptible to damage from an ESD event Important Safety Instructions gt O aution Wa 5 gt Warning This product is intended to be a component product of the RossGear 8000 series frame Refer to the RossGear 8000 series frame User Manual for important safety instructions regarding the proper installation and safe operation of the frame as well as it s component products Certain parts of this equipment namely the power supply area still present a safety hazard with the power switch in the OFF position To avoid electrical shock disconnect all A C power cords from the chassis rear appliance connectors before servicing this area Service barriers within this product are intended to protect the operator and service personnel from hazardous voltages For continued safety replace all barriers after any servicing This product contains safety critical parts which if incorrectly replaced may present a risk of fire or electrical shock Components contained within the product s power supplies and power supply area are not intended to be customer serviced and should be returned to the factory for repair To reduce the risk of fire replacement fuses must be the same type and rating Only use attachments accessories specified by the manufacturer EM
14. s Overview The SMPTE 269M Fault Reporting system also known as a SMPTE alarm provides indication if one or more frame modules encounter a fault or an abnormal condition The SEA 8008 module provides a jumper to enable SMPTE 269M fault reporting The card connects by means of an internal interface circuit to an auxiliary telco connector on RossGear 8000 series frames When the frame connection is interfaced with a customer designed system of LEDs or audible alarms faults can be traced to a specific frame when a card fault occurs within that frame The following diagram illustrates a general arrangement for SMPTE 269M alarm reporting Frame Mating AUX A Telco Jack Plug ALARM J15 i CIRCUIT POWER 1 2 2 From All 5 5 3 20 mA max SUPPLY Modules 4 MOC8101 TV o 24 Volt n olts max ae a 6 7V Internal Interface Circuit l Customer Supplied Alarm Figure 4 SMPTE 269M Alarm Reporting Internal interface and typical connections SEA 8008 User Manual Iss 05A SMPTE 269M Fault Reporting e 3 1 Jumper Setup Tf fault reporting for the SEA 8008 is desired use jumper JP2 FAULT REPORT 269M to set up the card 1 To access the jumper remove the card from the frame by pressing down the white card ejector tab and pulling the card from the frame slot 2 Observing all static discharge and handling precautions place the card with
15. ssGear SEA 8008 please contact the Ross Video Technical Support Department Contact information is supplied at the end of this publication A Return Material Authorization number RMA will be issued to you as well as specific shipping instructions should you wish our factory to repair your RossGear SEA 8008 If required a temporary replacement module will be made available at a nominal charge Any shipping costs incurred will be the responsibility of you the customer All products shipped to you from Ross Video Limited will be shipped collect The Ross Video Technical Support Department will continue to provide advice on any product manufactured by Ross Video Limited beyond the warranty period without charge for the life of the equipment 5 2 e Service Information SEA 8008 User Manual Iss 05A Ordering Information In This Chapter This chapter contains ordering information for the SEA 8008 and related products SEA 8008 and Related Products Standard Equipment e SEA 8008 Serial Equalizing Amplifier e 8008DR 004 Serial Equalizing Amplifier User Manual Optional Equipment e 8008DR 004 Serial Equalizing Amplifier User Manual additional User Manual e DFR 8104A Digital Products Frame and Power Supply PS 8102 IRU holds 4 modules includes 1 power supply e DFR 8104A C Digital Products Frame with Cooling Fan Module and Power Supply PS 8102 1RU holds 4 modules includes 1 power supply e DFR 8110A Digital Products
16. the component side facing up on a clean flat surface 3 To enable SMPTE fault reporting set jumper JP2 to ENABLE position To disable SMPTE fault reporting set jumper JP2 to DISABLE position uw m 2 gt A 7 m O gt D z oO z 18 lt m BNC_DESIGNATIONS INwSDI_IN BNCI 8 SDI OUT O E A Figure 5 SMPTE 269M Alarm Reporting Jumper Location Frame Connections The SMPTE 269M Fault Reporting connection on RossGear 8000 series frames is provided by the auxiliary telco connector AUX A for interfacing with a customer designed alarm system DFR 8104A Ross Graa YAA tA 7S AUX A Connector for SMPTE 269M A LO Fault Reporting Figure 6 SMPTE 269M Alarm Reporting Frame Connections Details The fault report contacts are closed when the card detects an internal failure or a power loss condition The fault report will pulse off for 1 to 2 ms about every 16ms if the input signal is low or missing Some internal failures are e Failure of the card to initialize e Failure in the fault reporting circuitry e Failure to detect a valid input signal to the card For additional information on alarm system design refer to the SMPTE document ANSI SMPTE 269M 1999 3 2 e SMPTE 269M Fault Reporting SEA 8008 User Manual Iss 05A Specifications In This Chapter This chapter contains the Technical Specifications table Technical Specifications Table 2 Technical Specifications Number Of Inp
17. the date of shipment from our factory In the event that your RossGear SEA 8008 proves to be defective in any way during this warranty period Ross Video Limited reserves the right to repair or replace this piece of equipment with a unit of equal or superior performance characteristics Should you find that this RossGear SEA 8008 has failed after your warranty period has expired we will repair your defective product should suitable replacement components be available You the owner will bear any labor and or part costs incurred in the repair or refurbishment of said equipment beyond the FIVE 5 year warranty period In no event shall Ross Video Limited be liable for direct indirect special incidental or consequential damages including loss of profits incurred by the use of this product Implied warranties are expressly limited to the duration of this warranty This RossGear SEA 8008 User Manual provides all pertinent information for the safe installation and operation of your RossGear Product Ross Video policy dictates that all repairs to the RossGear SEA 8008 are to be conducted only by an authorized Ross Video Limited factory representative Therefore any unauthorized attempt to repair this product by anyone other than an authorized Ross Video Limited factory representative will automatically void the warranty Please contact Ross Video Technical Support for more information In Case of Problems Should any problem arise with your Ro
18. uts 1 Standards SMPTE 259M DVB ASI formats NRZ or NRZI Input Impedance 750 Terminating Return Loss gt 30dB 19MHz gt 20dB 143 360MHz Automatic up to 31dB 305m of Belden 8281 270Mb s Common Mode Rejection gt 10Vp p 50 60Hz Equalization Number Of Outputs Output Impedance 750 Return Loss gt 30dB Y 19MHz gt 19dB 143 360MHz Signal Level 800mV 10 DC Offset 0 Volts 50 mV Rise and Fall Time 20 80 800ps Typical Overshoot gt 8 We recommend 200m or less of input cable due to jitter considerations Specifications are subject to change without notification SEA 8008 User Manual Iss 05A Specifications e 4 1 4 2 e Specifications SEA 8008 User Manual Iss 05A Service Information In This Chapter This chapter contains the following sections Troubleshooting Checklist Warranty and Repair Policy Troubleshooting Checklist Routine maintenance to this RossGear product is not required In the event of problems with your SEA 8008 the following basic troubleshooting checklist may help identify the source of the problem If the module still does not appear to be working properly after checking all possible causes please contact your Ross Video products distributor or the Ross Video Technical Support department at the numbers listed under the Contact Us section at the end of this manual 1 SEA 8008 User Manual Iss 05A Visual Review P
Download Pdf Manuals
Related Search