VDS Series PC Oscilloscopes Quick Guide
Contents
1. 2 Double click the created desktop shortcuts VDS 3 Connection Use the supplied USB cable to connect the USB port of the Oscilloscope in Figure 3 1 to the USB port of a PC Note If you use a USB cable which is not supplied by us some problems such as connection error and signal disturbing might occur 4 Install the USB driver In the window of VDS software press F1 to open the help document of the software Follow the steps of title I PC Software USB Driver Install Guide in the document to install the driver 6 How to Implement the Function Inspection z 4 Make a fast function check to verify the normal operation of the instrument First connect the oscilloscope with PC successfully and then do the following steps Click in the software interface to restore to factory settings The default attenuation coefficient set value of the probe in the software is 10X Set the Switch in the Oscilloscope Probe as 10X and Connect the Oscilloscope with CH1 Channel Align the slot in the probe with the plug in the CH1 connector BNC and then tighten the probe with rotating it to the right side Connect the probe tip and the ground clamp to the connector of the probe compensator Click on the right top of the software interface to auto set The square wave of 1 KHz frequency and 3 3V peak peak value will be displayed Check CH2 by repeating Step 2 and Step 3 7 How to Implement the Probe Compensation When connect t2. Passive probe 1 2 m 1 1 10 1 1x CD Supplied Software 1x USB cable 1x Silicon case 1x Quick Guide 1x AC DC adapter only for the model with LAN port Options 1x Soft case Appendix B General Care and Cleaning General Care To avoid any damage to the instrument or probe do not exposed it to any sprays liquids or solvents Cleaning Inspect the instrument and probes as often as operating conditions require To clean the instrument exterior perform the following steps l 2 Wipe the dust from the instrument and probe surface with a soft cloth Disconnect the USB cable before cleaning your Oscilloscope Clean the instrument with a wet soft cloth not dripping water It is recommended to scrub with soft detergent or fresh water To avoid damage to the instrument or probe do not use any corrosive chemical cleaning agent Warning Before power on again for operation it 1s required to confirm that the instrument has already been dried completely avoiding any electrical short circuit or bodily injury resulting form the moisture 10
3. IoSUr e aicaicsscecccacaictceccewascesuesedeateshecscssusccestececasnassedesssveedoadoussdeccs EN 10 Appendix B General Care and Cleaning sscssssseccccccsssescceccccosssesccecoosssssececsocssssssceeessssssssee 10 1 General Safety Requirements Before any operations please read the following safety precautions to avoid any possible bodily injury and prevent this product or any other products connected from damage In order to avoid any contingent danger this product is only used within the range specified Only the qualified technicians can implement the maintenance Pay attention to the nominal values of all terminals To avoid fire or electric shock please keep a watchful eye on all nominal values and marks specified for this product Before any connection performed on this product carefully read the user s manual of the product for further information of nominal values No touch is allowed on bare conductors When the product is powered on do not touch any bare joints or parts of the scope meter Operation is prohibited in case of any undetermined failure When in doubt any damage on this product consult the qualified personnel for checking on it Keep ventilation in good condition Refer to the user manual for detail installation instructions in order to fix this product correctly and provide it with good ventilation conditions No operation is allowed under a humid environment No operation is allowed under an expl
4. OWON VDS Series PC Oscilloscopes Quick Guide E VDS2062 E VDS3102 WWW OWON COM HK May 2013 edition V1 03 Copy Right in this Manual Lilliput Company All rights Reserved The Lilliput s products are under the protection of the patent rights in America and other countries including ones which have already obtained the patent rights and those which are applying for The information in this manual will replace all that in the materials published originally The information in this manual was correct at the time of printing However OWON will continue to improve products and reserves the rights to changes specification at any time without notice OWON is the registered trademark of the Lilliput Company Headquarter Fujian Lilliput Optoelectronics Technology Co Ltd The mansion of optoelectronics 19 Heming Road Lantian industrial zone Zhangzhou Fujian China Tel 86 596 2 130430 Fax 86 596 2109272 Web www owon com hk Mail Business Consulting info owon com hk Sale service service owon com hk Branch Xiamen Lilliput Technology Co Ltd the 5th floor B Area Chuangxin Mansion Software Park ZhenZhuWan Huandao RD Xiamen Fujian China Tel 86 592 2575666 Fax 86 592 2575669 General Warranty Lilliput warrants that the product will be free from defects in materials and workmanship for a period of 3 years from the date of purchase of the product by the original purchaser from the Lilliput Company And the
5. he probe with any input channel for the first time make this adjustment to match the probe with the input channel The probe which is not compensated or presents a compensation deviation will result in the measuring error or mistake For adjusting the probe compensation please carry out the following Steps 1 Click in the software interface to show the Home menu Choose Channel set the Probe Rate in the menu as 10 Set the switch in the probe as 10X and connect the probe with the CH1 channel If a probe hook tip is used ensure that it keeps in close touch with the probe Connect the probe tip with the signal connector of the probe compensator and connect the reference wire clamp with the ground wire connector of the probe connector and then click A on the right top of the software interface to auto set The set values of the probe switch are 1X and 10X Figure 7 1 Attenuation Switch 2 Check the displayed waveforms and regulate the probe till a correct compensation is achieved see Figure 7 2 and Figure 7 3 Overcompensated Compensated correctly Under compensated Figure 7 2 Displayed Waveforms of the Probe Compensation 3 Repeat the steps mentioned if needed ie ae Figure 7 3 Adjust Probe 8 How to Use the Probe Safely The safety guard ring around the probe body protects your finger against any electric shock shown as Figure 8 1 Figure 8 1 Finger Guard A N Warning To avoid electric shock always kee
6. ng The two channels of the oscilloscope are non isolated electrically The channels should adopt common basis during measuring To prevent short circuits the 2 probe ground must not be connected to 2 different non isolated DC level LN Warning The channels should adopt common basis during measuring To prevent short circuits the 2 probe ground must not be connected to 2 different non isolated DC level The diagram of the oscilloscope ground wire connection Probe Oscilloscope AC Adapter Electrical Outlet Signal Input Ground Clip The diagram of the ground wire connection when the oscilloscope powered by PC USB is connected to the AC powered PC through the USB ports Oscilloscope Probe PC USB power PC Electrical Outlet USB Cable Ground Clip It is not allowed to measure AC power when the oscilloscope is AC powered through the adapter or when the oscilloscope powered by PC USB is connected to the AC powered PC through the ports LN Warning To avoid fire or electrical shock if a test tool input is connected to more 42V peak 30Vrms or on circuits of more than 4800VA Use only insulated probes and adapter supplied with the test tool or indicated by OWON as suitable for the Oscilloscope Before use inspect probes and accessories for mechanical damage and replace when damaged Remove all probes and accessories that are not in use Do not apply voltages that differ more than 400 V from earth gr
7. ommended that you should make a check on the instrument according to the following steps 1 Check whether there is any damage caused by transportation If it is found that the packaging carton or the foamed plastic protection cushion has suffered serious damage do not throw it away first till the complete device and its accessories succeed in the electrical and mechanical property tests 2 Check the Accessories The supplied accessories have been already described in the Appendix A Enclosure of this Manual You can check whether there is any loss of accessories with reference to this description If it is found that there is any accessory lost or damaged please get in touch with the distributor of Lilliput responsible for this service or the Lilliput s local offices 3 Check the Complete Instrument If it is found that there is damage to the appearance of the instrument or the instrument can not work normally or fails in the performance test please get in touch with the Lilliput s distributor responsible for this business or the Lilliput s local offices If there is damage to the instrument caused by the transportation please keep the package With the transportation department or the Lilliput s distributor responsible for this business informed about it a repairing or replacement of the instrument will be arranged by the Lilliput 5 How to Connect with PC 1 Install the Software Install the software on the supplied CD exe
8. osive environment Keep clean and dry on the product surface The method which stipulated according to the factory does not use the equipment possibly can damage the protection which the equipment provides 2 Safety Terms and Symbols Safety Terms Terms in this manual The following terms may appear in this manual LN Warning Warning indicates the conditions or practices that could result in injury or loss of life A Caution Caution indicates the conditions or practices that could result in damage to this product or other property Terms on the product The following terms may appear on this product Danger It indicates an injury or hazard may immediately happen Warning It indicates an injury or hazard may be accessible potentially Caution It indicates a potential damage to the instrument or other property might occur Safety Symbols Symbols on the product The following symbol may appear on the product AA Hazardous Voltage Refer to Manual Protective Earth Terminal b Chassis Ground E Test Ground To avoid body damage and prevent product and connected equipment damage carefully read the following safety information before using the test tool This product can only be used in the specified applications LN Warning To avoid fire or electrical shock please use proper power adapter Use only the power adapter appointed by the manufacturer and subject to approval of being used in the user s country LN Warni
9. ound to any input when measuring ina CAT environment Do not apply voltages that differ more than 400 V from each other to the isolated inputs when measuring ina CAT I environment Do not apply input voltages above the rating of the instrument Use caution when using 1 1 test leads because the probe tip voltage will be directly transmitted to the Oscilloscope Do not touch the exposed part of metal BNC Do not insert metal objects into connectors Always use the Oscilloscope only in the manner specified Voltage ratings that are mentioned in the warning are giver as limits for working voltage The represent V ac rms 50 60Hz for AC sine wave applications and as V dc for DC applications Overvoltage Category II refers to local level which is applicable for appliances and portable equipment 3 Ports Introduction Figure 3 1 Ports of the Oscilloscope take VDS3102 for instance RS 232C Port optional USB port Supply power by PC USB or the adapter communicate with PC LAN port optional Network port which can be used to connect with PC Probe Compensation Measurement signal 3 3V 1 KHz output EXT trigger input trigger output or Pass Fail output Signal input of Channel 2 ee ee YY SS Signal input of Channel 1 Note If you use LAN port to communicate with PC the oscilloscope should be powered by the adapter 4 How to Implement the General Inspection After you get a new VDS series oscilloscope it 1s rec
10. p your finger behind the safety guard ring of the probe during the operation To protect you from suffering from the electric shock do not touch any metal part of the probe tip when it is connected to the power supply Before making any measurements always connect the probe to the instrument and connect the ground terminal to the earth 9 Performance parameters Model Bandwidth Sample rate Rise time Horizontal Scale S div VDS2062 60MHz 500MS s 5ns div 100s div step by1 2 5 VDS3102 100MHz 1GS s 2ns div 100s div step by1 2 5 Sampling mode Sample Peak detect Average Channel 2 1 External Record length Max 10M Input coupling DC AC Ground Input impedance 1IMQ 2 in parallel with 100F 5pF Max input voltage 40V PK PK DC AC PK Pk DC gain accuracy 3 Vertical sensitivity 2mV div 5V div Trigger type Edge Video Slope Pulse Alternate Trigger mode Auto Normal Single Line field Support standard NTSC PAL and SECAM broadcast systems frequency Video Amali Vpp Vmax Vmin Vtop Vbase Vamp Vavg Vrms Overshoot Preshoot Freq Period Rise Time Fall Time Delay A B Delay A B Width measurement Width Duty Duty Waveform Math x FFT Communication l USB2 0 LAN optional RS 232 optional Waveform Math 5 0V 1A Power consumption lt 4W Dimension 190mmx 120mmx18mm L H W About 0 26 kg 10 Appendix Appendix A Enclosure Standard Accessories A pair of
11. products when the effect of such modification or integration increases the time or difficulty of servicing the product Please contact the nearest Lilliput s Sales and Service Offices for services or a complete copy of the warranty statement For better after sales service please visit www owon com hk and register the purchased product online Excepting the after sales services provided in this summary or the applicable warranty statements Lilliput will not offer any guarantee for maintenance definitely declared or hinted including but not limited to the implied guarantee for marketability and special purpose acceptability Lilliput should not take any responsibilities for any indirect special or consequent damages Table of Contents 1 General Safety KegtiremMe NiS sucscwiverersisansesoteseaustuessunsewiguvarsieapsaredsswewatuessunsemiaeversbenmaresies 1 2 Sajety Terms Gnd SVMPOUS viinien A E E A EE 2 SFornsIniroduchom eeen E E 5 4 How to Implement the General INspection sssssscccccccccccccccccccssssssssssssssssssesececeeeecees 6 5 How to Connect wih PC siirron e a iae 6 6 How to Implement the Function INSPection 00000sssessssecccccccccccccccccccccssssssssssesssees 7 7 How to Implement the Probe Compensation sssssseeeeeoooossssssssssssseeeeeeeeeecoossssssssssses 7 S Howto Use the Frobe Safely osn n en E R us 8 DP CrfOVINGNCE PATAINCLCTS serieren ae EEE TOERE 9 TO APPENA veisia A E 10 Append At ENC
12. warranty period of accessories such as probe battery is 12 month This warranty only applies to the original purchaser and is not transferable to the third party If the product proves defective during the warranty period Lilliput either will repair the defective product without charge for parts and labor or will provide a replacement in exchange for the defective product Parts modules and replacement products used by Lilliput for warranty work may be new or reconditioned to like new performance All replaced parts modules and products become the property of Lilliput In order to obtain service under this warranty Customer must notify Lilliput of the defect before the expiration of the warranty period Customer shall be responsible for packaging and shipping the defective product to the service center designated by Lilliput and with a copy of customer proof of purchase This warranty shall not apply to any defect failure or damage caused by improper use or improper or inadequate maintenance and care Lilliput shall not be obligated to furnish service under this warranty a to repair damage resulting from attempts by personnel other than Lilliput representatives to install repair or service the product b to repair damage resulting from improper use or connection to incompatible equipment c to repair any damage or malfunction caused by the use of non Lilliput supplies or d to service a product that has been modified or integrated with other
Download Pdf Manuals
Related Search