Home
Manual ENG - Jasopels.dk
Contents
1. and the air compressor system must be min 12 e The skinning machine is now ready for use Note To prevent possible damage to the machine s micro controller and other electrical systems in connection with thunderstorms it is recommended to disconnect the electricity connection when the machine is not in use 7 Operation Provided that the electricity and compressed air is correctly installed as described earlier e 1 Start by releasing the skin from the back part of the mink Place the back part of the body in the upper holder back body holder with the belly downwards e 2 By activating the left foot pedal the top holder closes down on the back part of the mink s body at low pressure Step back on left foot pedal to activate the high pressure Warning Since there is a RISK of pinching hazard when the control panel activates the free hand has to be placed outside the abdomen and shoulder holding operation area e 3 Step now on the right foot pedal and the lever will move up e 4 Now pull the loose skin by hand so far that the mink s back skin can be placed between the retaining rubber on the lower holder skin holder Note Only the back skin may be placed in the skin holder e 5 By stepping on both pedals the skin holder is being locked e 6 Now press the foot pedals separately Right foot pedal drives the lever down and the skin is pulled off The left pedal activat
2. on proper use and handling of the machine View this user manual for more information 4 Symbol Explanation Please read this manual and follow the instructions provided To emphasize certain information the following terms are being used e Note A triangle containing an exclamation point is a warning symbol to warn about any important instructions or information concerning this machine e Danger A triangle containing lightning is a warning symbol that warns of High Voltage e Warning A triangle containing entrapment hazard 5 Machine introduction Skinning machine T11 is designed to relieve the skinning staff and thereby take the hard work of pulling the skin off mink carcasses The machine is a newly developed machine where occupational safety and ergonomics in particular have been improved The machine is built so that there is plenty of room to cut free by the ears and the eyes The high mobility also makes it easy to move the mink and the fur The newly developed body remover automatically removes the skinned body of the machine once Empty button is pressed This way the operator is exempt from a great deal of repetitive and exhausting lifting The machine s pulling function is mechanically constructed with increased traction which makes it possible to stop very precisely by ears and eyes The seat is adjustable in both height and forward back which facilitates alignment with the perfect postur
3. User Manual 1 Declaration of Conformity EU Declaration of Conformity Producer Jasopels A S Address Fabriksvej 19 DK 7441 Bording Denmark TIf 45 98 43 99 66 Machine Skinning machine T11 Type 19 0000 Jasopels A S declares that this product complies with the following EU Directives 89 336 EEC 98 37 EEC Furthermore we declare that the following harmonized standards have been applied EN 60204 1 EN 983 Time and place Bording 1 August 2008 Name Adm Manager Poul Bach BAGA 2 Contents Declaration of Conformity ssseeeeeeeeeeeneeeeees 2 s Contents pa ANA AA iaaa iiaiai 3 sc AG Sea ASEE E AE T PAGPA 4 Symbol Explanation 5 Machine introduction c sccccssssesseseseseeenseeseeseeeneees 6 s FUnCtONiINg cece se ttcecescnsiincessneddceonsccceteecccasenieevieeeicecestes 7 age AA AP 8 Maintenance cccecsescseecneecneeeeeeeeeeeneeeneseuseeneseneseneees 9 Technical daa AA 11 OONOARAOND e This User Manual is an important part of your new machine Read the manual carefully and use it as a reference book e This manual contains important information about safety and use of machinery The manual should be kept with the machine e Itis important that the user manual is kept with the machine in case of resale or lending e The user of the machine has to ensure that the operator service personnel and others who have access to the machine are instructed
4. e The machine is simple and easy to operate however the User manual shall be read before using the machine The user of the machine must ensure that the operator service personnel and others who have access to the machine are instructed on proper use and handling of the machine View this user manual for further information The machine must only be used for the purpose it was designed for Whatever problems may arise with the machine or its operation the errors may not be corrected before the machine is properly stopped Minor corrections can be done via the machine controls The User Manual should always be kept accessible to the operator Note 6 Functioning Before the skinning machine is put into service check that it stands on a firm and stable surface The adjustable machine feet have to be set so that the machine is leveled and is not rickety The skinning machine is originally fitted with a 5 pole 16 A CEE plug on the supply cable and has to be connected to an outlet with 3 400V PE On the machine s left side under the foot pedal an air filter is fitted with a quick coupling where the hose from the compressor is mounted Note During the connection of compressed air one should stay in a safe distance of the machine as there may cause incidental cylinder movements e hir pressure should be eight bars e The hose connecting the skinning machine
5. es the chains So one can find the best position for cutting the head loose e 7 By performing weak pumping movements on the foot pedal you can now release the skin in precise tugs Cut the skin free by the ears and the eyes e 8 Once the skin has slipped throughout the body press the EMPTY button on the control panel whereby abdomen and skin holders are opened the body remover runs the peeled mink body out of the end of the machine The shoulder holder opens and runs back into the starting position Warning There is a RISK of entrapment hazard between the skin holder and the support roller when the skin holder returns to the starting position 9 When the skin and the body is removed the skinning machine is ready for the next repetition STOP By pressing the red STOP button on the Emergency Stop panel the machine immediately cuts off pressure and the current process is stopped The machine is reset by pressing the red button under the emergency stop 7A Setting the machine s height To achieve the best ergonomic working position for the operator the skinning machine is designed with height adjustable legs The height can be adjusted on the four bolts DANGER Disconnect the compressed air and electricity on the machine before maintenance cleaning and other service is executed on the machine e Empty the air filter water separator daily Press the button under the glass until
6. the glass is empty The water separator can also empty itself by disconnecting the air hose on the coupling If there are oil residues and other impurities in the filter the glass should be removed and cleaned in hot soapy water e The skinning machine should be cleaned daily after use with compressed air and possibly hot water in the places where there is a lot of blood In particular the moving parts of the skin holder should be kept free of sawdust and dirt It is also important to avoid unintended stoppages to clean below the moving back holder It can be made with hot water and a brush e After the skinning is finished the machine should be cleaned the compressed air and electricity should be disconnected 9 Technical data e Electrical connection 16A 5 pole CEE sockets 3X400 V N PE Electricity consumption Air connection Air consumption Measurement Max 5 1 A Quick coupling Coupling 8 bar 2 l min Height 130 cm Length 170 cm Width 80 cm
Download Pdf Manuals
Related Search
Related Contents
Operating Manual Manuel d`utilisation di legge - Senato della Repubblica StarTech.com DisplayPort 1.2 cable with latches – certified, 6 ft HQ W7-60351 このドキュメントについて このドキュメントは、アジレント MSDSへ - Meiji Seikaファルマ 一般産業・造船・建築設備用 Guía del usuario Copyright © All rights reserved.
Failed to retrieve file