Home

CE EMC TEST REPORT

1. dBuV m 70 0 60 0 50 0 400 tu HE wop y OS CTT TTT ni 50 100 200 300 400 ip 600 700800 1000 Frequency MHz No Frequency Reading Correction Result Limit Margin Degree Height Remark MHz dBuV Factor dB m dBuV m dBuV m dB cm 1 176 94 10 09 12 66 22 75 30 00 7 25 360 00 400 00 QP 2 223 23 13 87 12 93 26 80 30 00 3 20 0 00 400 00 QP 3 334 43 12 28 19 32 31 60 37 00 5 40 0 00 320 80 QP 4 398 49 10 84 21 76 32 60 37 00 4 40 114 60 311 20 QP 5 506 77 8 89 23 71 32 60 37 00 4 40 360 00 251 20 QP 6 550 94 4 33 25 07 29 40 37 00 7 60 360 00 145 60 QP 7 835 66 3 60 29 25 32 85 37 00 4 15 359 20 100 00 QP REMARKS The other emission levels were very low against the limit Page 23 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Report No 81004101 E 7 4 HARMONICS CURRENT MEASUREMENT 7 4 1 LIMITS OF HARMONICS CURRENT MEASUREMENT Limits for Class A equipment Limits for Class D equipment Harmonics Max permissible Harmonics Max permissible harmonics Max permissible SH current SH current per watt mA W EE current Odd harmonics Odd Harmonics only 3 2 30 3 3 4 2 30 5 1 14 5 1 9 1 14 7 0 77 7 1 0 0 77 9 0 40 9 0 5 0 40 11 0 33 11 0 35 0 33 13 0 21 13
2. Dips Interruption and HAEFELY Verations simulator TRENCH PLINE 1610 080 344 05 04 16 2009 Test S W Winpats 3 25 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration required 8 9 3 TEST PROCEDURE please refer to measurement standard or CCS SOP PA 028 The EUT and support units were located on a wooden table 0 8 m away from ground floor Setting the parameter of tests and then perform the test software of test simulator Conditions changes to occur at 0 degree crossover point of the voltage waveform Recording the test result in test record form Removes the Battery Pack to test if any a ZS ra ba Page 55 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 9 4 TEST SETUP To AC Source Dips Interruption EUT and Variations amp Simulator Support Units Controller Computer For the actual test configuration please refer to the related item Photographs of the Test Configuration 8 9 5 TEST RESULTS Temperature 28c Humility 53 RH Required Passing Criterion B gt 95 reduction 0 5 period Performance Criterion C 30 reduction 25 period amp gt 95 reduction 250 period Test Power 230Vac 50Hz Voltage Duration Performance 04 Reduction Period Test Result a Ee e noer
3. A IEC 61000 4 5 Surge Immunity Test Basic Standard 1 2 50 us Open Circuit Voltage Specification 8 20 us Short Circuit Current and AC Power Port line to line 1kV line to earth ground 2kV Performance DC Power Port line to earth 0 5kV Criterion Signal Ports and Telecommunication Ports line to ground 1kV required Performance Criterion B IEC 61000 4 6 Conducted Radio Frequency Disturbances Test CS 0 15 80 MHz 3Vrms 80 AM 1kHz Performance Criterion A IEC 61000 4 8 Power frequency magnetic field immunity test 50 Hz 1A m Performance Criterion A i gt 95 reduction for 0 5 period Performance Criterion B ii 30 reduction for 25 period Performance Criterion C Voltage Interruptions gt 95 reduction for 250 period Performance Criterion C Page 31 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 2 GENERAL PERFORMANCE CRITERIA DESCRIPTION Criteria A Criteria B Criteria C The apparatus shell continues to operate as intended without operator intervention No degradation of performance or loss of function is allowed below a performance level specified by the manufacturer when the apparatus is used as intended The performance level may be replaced by a permissible loss of performance If the manufacturer does not specify the minimum performance level or the permissible perform
4. 2000 IEC 61000 4 11 2004 Deviation from Applicable Standard None The above equipment has been tested by Compliance Certification Services Inc and found compliance with the requirements set forth in the Electromagnetic Compatibility Directive 2004 108 EC and technical standards mentioned above The results of testing in this report apply only to the product system which was tested Other similar equipment will not necessarily produce the same results due to production tolerance and measurement uncertainties Approved by Reviewed by Qriewt Hu els ule Robert Huang Julia Wei Section Manager Senior Specialist Page 4 This report shall not be reproduced except in full without the written approval of Compliance Certification Services A CCS Compliance Certification Services Inc dll Report No 81004101 E 2 TEST RESULT SUMMARY Standard em Result Remarks Conducted PASS Meet Class B limit Main Port N A Not applicable because EN 55022 2006 Randi the EUT doesn t have LAN Telecommunication port port or Modem port Radiated PASS Meet Class B limit EN 61000 3 2 2006 PASS Meet Class D limit SE GE ZER Voltage fluctuations amp flicker PASS Meets the requirements IMMUNITY EN 55024 1998 A1 2001 A2 2003 Standard Result Remarks ree GE TEE PASS Meets the requirements of Performance Criterion B IEC 61000 4 3 2002 A1 2002 PASS Meets the req
5. 3 de 3 3 dc means relative steady state voltage change 7 5 2 TEST INSTRUMENTS IMMUNITY SHIELDED ROOM Name of Equipment Manufacturer Model Serial Number Calibration Due HARMONICS SYSTEM EMC PARTNER HARMONICS 1000 12 06 2008 Test S W HARCS Immunity 4 10 NOTE The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA Page 26 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc HEET 7 5 3 TEST PROCEDURE please refer to measurement standard or CCS SOP PA 030 The EUT was placed on the top of a wooden table 0 8 meters above the ground and operated to produce the most unfavorable sequence of voltage changes under normal operating conditions During the flick measurement the measure time shall include that part of whole operation cycle in which the EUT produce the most unfavorable sequence of voltage changes The observation period for short term flicker indicator is 10 minutes and the observation period for long term flicker indicator is 2 hours 7 5 4 TEST SETUP Harmonics amp Flicker Analyzer Power Source For the actual test configuration please refer to the related item Photographs of the Test Configuration Page 27 This report shall not be reproduced except in full without the written approval
6. 74 53 43 40 30 NOTE The limits decrease linearly with the logarithm of the frequency in the range 0 15 MHz to 0 5 MHz For Class B Equipment Voltage Limit dBuV Current Limit dBuA FREQUENCY MHz 0 15 0 5 84 74 74 64 40 30 30 20 NOTE The limits decrease linearly with the logarithm of the frequency in the range 0 15 MHz to 0 5 MHz Page 16 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ee ee 7 2 2 TEST INSTRUMENTS Conducted Emission Room Name of Equipment Manufacturer Medel Serial Number Caltbration Due PNA NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration Request 7 2 3 TEST PROCEDURE please refer to measurement standard or CCS SOP PA 031 Selecting ISN for unscreened cable or a current probe for screened cable to take measurement The port of the EUT was connected to the remote side support equipment through the ISN Current Probe and communication in normal condition Making a overall range scan by using the test receiver controlled by controller and record at least six highest emissions for showing in the test report Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level an
7. Class A dBuV Class B dBuV FREQUENCY MHz osos o e es e Cows m o ww 0 NOTE 1 The lower limit shall apply at the transition frequencies 2 The limit decreases in line with the logarithm of the frequency in the range 0 15 to 0 50 MHz 3 All emanations from a class A B digital device or system including any network of conductors and apparatus connected thereto shall not exceed the level of field strengths specified above 7 1 2 TEST INSTRUMENTS Conducted Emission Room 3 Name of Equipment Manufacturer Model Serial Number Calibration Due EMI Test Receiver R amp S ESCS30 845552 030 04 08 2009 LISN R amp S ENV216 ENV216 O 100074 12 03 2008 FCC LISN 50 LISN Fcc SE 06013 10 16 2008 Test S W LabVIEW 6 1 CCS Conduction Test SW Version_01 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration Request Page 11 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc HEET 7 1 3 TEST PROCEDURES please refer to measurement standard or CCS SOP PA 031 Procedure of Preliminary Test The EUT and support equipment if needed were set up as per the test configuration to simulate typical usage per the user s manual When the EUT is a tabletop syste
8. NIST USA 2 N C R No Calibration required 8 8 3 TEST PROCEDURE please refer to measurement standard or CCS SOP PA 027 a The equipment was configured and connected to satisfy its functional requirements It shall be placed on the GRP with the interposition of a 0 1m thick insulating support b The equipment cabinets shall be connected to the safety earth directly on the GRP via the earth terminal of the EUT c The power supply input and output circuits shall be connected to the sources of power supply control and signal d The cables supplied or recommended by the equipment manufacturer shall be used 1 meter of all cables used shall be exposed to the magnetic field Page 52 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 8 4 TEST SETUP Induction Coil 1 2 Dimension of EUT Signal Generator To Earth Ground For the actual test configuration please refer to the related item Photographs of the Test Configuration NOTE TABLETOP EQUIPMENT The equipment shall be subjected to the test magnetic field by using the induction coil of standard dimension 1m x 1m The induction coil shall then be rotated by 90 degrees in order to expose the EUT to the test field with different orientations FLOOR STANDING EQUIPMENT The equipment shall be subjected to the test magnetic field by using in
9. NOTE TABLE TOP AND FLOOR STANDING EQUIPMENT The equipment to be tested was placed on an insulating support of 0 1 meters height above a ground reference plane All relevant cables shall be provided with the appropriate coupling and decoupling devices at a distance between 0 1 meters and 0 3 meters from the projected geometry of the EUT on the ground reference plane 8 7 5 TEST RESULTS Humidity 52 RH Pressure 991mbar Tested By Required Passing Performance Criterion A Frequency peld Injection Performance Band MHz SE Method Criterion Observation NOTE 1 There was no change compared with initial operation during the test Page 51 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 8 POWER FREQUENCY MAGNETIC FIELD 8 8 1 TEST SPECIFICATION Basic Standard IEC 61000 4 8 Frequency Range 50Hz Field Strength 1 A m Observation Time 1 minute Inductance Coil Rectangular type 1mx1m 8 8 2 TEST INSTRUMENT Immunity Shield Room Name of Equipment Manufacturer Model Serial Number Calibration Due TRIAX ELF Magnetic Field Meter F W BELL 4090 9711 11 28 2008 Clamp Meter 300K 11 5980 K 11 26 2008 a HAEFELY Magnetic Field Tester TRENCH MAG 100 1 080 938 01 06 04 2009 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and
10. Ports and Telecommunication Ports 0 5kV Polarity Positive amp Negative Impulse Frequency 5 kHz Impulse Wave shape 5 50 ns Burst Duration 15 ms Burst Period 3 Hz Test Duration Not less than 1 min 8 5 2 TEST INSTRUMENT Immunity Shield Room Name of Equipment Manufacturer Model Serial Number Calibration Due EMC TEST SYSTEM EMC PARTNER TRANSIENT 2000 754 08 31 2009 Test S W Genecs 2 54 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration required 8 5 3 TEST PROCEDURE please refer to measurement standard or CCS SOP PA 024 a Both positive and negative polarity discharges were applied b The length of the hot wire from the coaxial output of the EFT generator to the terminals on the EUT should not exceed 1 meter c The duration time of each test sequential was 1 minute d The transient burst waveform was in accordance with IEC 61000 4 4 5 50ns Page 44 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Report No 81004101 E 8 5 4 TEST SETUP 10cm AC Line EFT Burst Surge Generator Controller Computer For the actual test configuration please refer to the related item Photographs of the Test Configuration NOTE TABLETOP EQUIPMENT The confi
11. Power Cord Type Unshielded 1 8m Detachable to Power Adapter Power Adapter Power Rating Unshielded 1 8m Non detachable with a Core at Power DC Power Cable Type Adapter CPU Manufacturer intel Model Celeron M 1 0GHz Memory Manufacturer Transcend Installed 1GB 8 4 LCD Panel Manufacturer TOSHIBA Modei LTA084C191F Inverter Board MFR WM1001 10 HDD Manufacturer ST940813AM 40GB Main Board Manufacturer 1680 100 RS 232 Cable Type Unshielded 1 8m Detachable UO PORT UO PORT TYPES Q TY TESTED WITH 1 Serial Port 1 2 Earphone Port 1 3 Microphone Port 1 4 USB Port 3 Note 1 The mean of X X A Z a z 0 9 Blank or Slash on model number they are identical just for marketing purpose only 2 Client consigns only one sample to test model number RO8I68M RTXXXxX Therefore the testing Lab just guarantees the unit which has been tested Page 6 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ee ee 4 TEST METHODOLOGY 4 1 DECISION OF FINAL TEST MODE 1 The following test mode s were scanned during the preliminary test Pre Test Mode Mode 1 800 x 600 Resolution 2 After the preliminary scan the following test mode was found to produce the highest emission level Final Test Mode Conducted eet Mode 1 EE Emiss
12. are terminated by a 50 ohm load resistor The frequency range was swept from 150 kHz to 80 MHz using the signal level established during the setting process and with a disturbance signal of 80 amplitude The signal was modulated with a 1 kHz sine wave pausing to adjust the RF signal level or the switch coupling devices as necessary The sweep rate was 1 5 x 10 decades s Where the frequency range is swept incrementally the step size was 1 of preceding frequency value from 150 kHz to 80 MHz The dwell time at each frequency was less than the time necessary for the EUT to be exercised and able to respond Sensitive frequencies such as clock frequency ies and harmonics or frequencies of dominant interest was analyzed separately Attempts was made to fully exercise the EUT during testing and to fully interrogate all exercise modes selected for susceptibility Page 50 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 7 4 TEST SETUP 10 cm isolation supporter AUX Support units Power RF Signal Amplifier Generator Note 1 The EUT is setup 0 1m above Ground Reference Plane 2 The CDNs and or EM clamp used for real test depends on ports and cables configuration of EUT Ground Reference Plane For the actual test configuration please refer to the related item Photographs of the Test Configuration
13. 0 30 0 21 15 lt n lt 39 0 15x15 n 15 lt n lt 39 3 85 n 0 15x15 n Even harmonics 2 1 08 4 0 43 6 0 30 8 lt n lt 40 0 23x8 n NOTE 1 Class A and Class D are classified according to item 7 4 3 2 According to section 7 of EN 61000 3 2 the above limits for all equipment except for lighting equipment having an active input power gt 75 W and no limits apply for equipment with an active input power up to and including 75 W 7 4 2 TEST INSTRUMENTS Immunity Shielded Room Name of Equipment Name of Equipment Manufacturer Manufacturer Model Serial Number Calibration Due HARMONICS SYSTEM EMC PARTNER HARMONICS 1000 om 12 06 2008 Test ISW HARCS Immunity 4 10 NOTE The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA Page 24 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc HEET 7 4 3 TEST PROCEDURE please refer to measurement standard or CCS SOP PA 029 The EUT was placed on the top of a wooden table 0 8 meters above the ground and operated to produce the maximum harmonic components under normal operating conditions for each successive harmonic component in turn The classification of EUT is according to section 5 of EN 61000 3 2 The EUT is classified as follows Class A Bal
14. 20 us Short Circuit Current Test Voltage AC Power Port line to line 1kV line to earth ground 2kV DC Power Port line to earth 0 5kV Signal Ports and Telecommunication Ports line to ground 1kV Surge Input Output AC Power Port L1 L2 L1 PE L2 PE DC Power Port L1 PE Signal Ports and Telecommunication Ports T to Ground R to Ground Generator Source Impedance 2 ohm between networks 12 ohm between network and ground Polarity Positive Negative Phase Angle 0 90 180 270 Pulse Repetition Rate 1 time min maximum Number of Tests 5 positive and 5 negative at selected points 8 6 2 TEST INSTRUMENT EE Shield Room Name Name of Equipment Name of Equipment Manufacturer Manufacturer Serial Number Number Calibration Due Due HAEFELY Surge Tester TRENCH PSUGER 4010 583 334 71 08 31 2009 Test TetSwW Winpats 3 25 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration required Page 46 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ee 8 6 3 TEST PROCEDURE please refer to measurement standard or CCS SOP PA 025 a For EUT power supply The surge is applied to the EUT power supply terminals via the capacitive coupling network Decoupling networks are required in order to av
15. CC DoC Unshielded 1 8m Headset USB 2 0 5 F12 U A0100214 39t0003 FCC DoC TeraSys Unshielded 1 8m External HDD Note Grounding was established in accordance with the manufacturer s requirements and conditions for the intended use 5 2 CONFIGURATION OF SYSTEM UNDER TEST 8 4 Rugged Tablet PC Test table Page 8 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc HEET 6 FACILITIES AND ACCREDITATIONS 6 1 FACILITIES All measurement facilities used to collect the measurement data are located at No 81 1 Lane 210 Pa De 2nd Rd Luchu Hsiang Taoyuan Shien Taiwan The sites are constructed in conformance with the requirements of ANSI C63 4 and CISPR Publication 22 All receiving equipment conforms to CISPR 16 1 1 CISPR 16 1 2 CISPR 16 1 3 CISPR 16 1 4 CISPR 16 1 5 6 2 ACCREDITATIONS Our laboratories are accredited and approved by the following approval agencies according to ISO IEC 17025 Taiwan TAF USA A2LA The measuring facility of laboratories has been authorized or registered by the following approval agencies Canada Industry Canada Germany TUV Rheinland Japan VCCI Taiwan BSMI USA FCC Copies of granted accreditation certificates are available for downloading from our web site http www ccsemc com Page 9 This report shall not be reproduced except in full without the written appr
16. Compliance Certification Services Inc eee CE EMC TEST REPORT for 8 4 Rugged Tablet PC MODEL RO8I68M RTXXXX X A Z a z 0 9 Blank or Slash Test Report Number 81004101 E Issued for Winmate Communication Inc 9F No 111 6 Shing De Rd San Chung City Taipei 241 Taiwan R O C Issued By Compliance Certification Services Inc Linkuo Laboratory No 81 1 Lane 210 Pa De 2nd Rd Luchu Hsiang Taoyuan Shien 338 Taiwan R O C TEL 886 3 324 0332 FAX 886 3 324 5235 E Mail service tw ccsemc com Issued Date October 13 2008 viji UY DN gr E Ss ACCREDITED Ka Ze Testing Laboratory Unf AW TESTING CERT 0824 01 0363 Note This report shall not be reproduced except in full without the written approval of Compliance Certification Services Inc This document may be altered or revised by Compliance Certification Services Inc personnel only and shall be noted in the revision section of the document The client should not use it to claim product endorsement by TAF A2LA NIST or any government agencies The test results in the report only apply to the tested sample Page 1 63 Compliance Certification Services Inc Report No 81004101 E Revision History Issue Effect Rev Date Revisions Page Revised By oo October 13 2008 Initial issue o Initial Issue Issue ALL Jill Jill Shiau Page 2 This report shall not be reproduced except in full without the written approva
17. IELD TEST FAST TRANSIENTS BURST TEST a GIE Page 61 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ee re SURGE IMMUNITY TEST Page 62 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Se POWER FREQUENCY MAGENTIC FIELD IMMUNITY TEST VOLTAGE DIPS INTERRUPTION TEST Page 63 This report shall not be reproduced except in full without the written approval of Compliance Certification Services
18. LECTROSTATIC DISCHARGE ESD 8 3 1 TEST SPECIFICATION Basic Standard IEC 61000 4 2 Discharge Impedance 330 ohm 150 pF Discharge Voltage Air Discharge 2 4 8 kV Direct Contact Discharge 2 4 kV Direct Indirect Polarity Positive amp Negative Air Discharge min 10 times at single test point for each Number of Discharge negative and positive polarity Contact Discharge min 200 times in total Discharge Mode Single Discharge 1 second minimum 8 3 2 TEST INSTRUMENT IMMUNITY SHIELDED ROOM Name of Equipment Manufacturer Model Serial Number Calibration Due ESD Generator SCHAFFNER NSG438 08 21 2009 NOTE The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA Page 33 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 3 3 TEST PROCEDURE please refer to measurement standard or CCS SOP PA 022 The discharges shall be applied in two ways a o Contact discharges to the conductive surfaces and coupling planes The EUT shall be exposed to at least 200 discharges 100 each at negative and positive polarity at a minimum of four test points One of the test points shall be subjected to at least 50 indirect discharges to the center of the front edge of the Horizontal Coupling Plane HCP The remaining three test
19. Margin dB Result dBuV m Limit dBuV m Q P Quasi Peak Page 21 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc 7 3 6 TEST RESULTS 28 C 57 RH Report No 81004101 E 6dB Bandwidth 120 kHz dBu m 70 0 60 0 50 0 400 7 a Sar ee Ce S 30 0 Eo o dx T T a e es er SS ee Ea RSA E KZ ER WE E e ST IL ES RS SE DU i i i i I I i i i i 30 50 100 200 300 400 500 600 700800 1000 Frequency MHz2 No Frequency Reading Correction Result Limit Margin Degree Height Remark MHz dBuV Factor dB m dBuV m dBuV m dB cm 1 173 40 12 50 12 77 25 27 30 00 4 73 215 60 100 00 QP 2 224 04 13 87 12 93 26 80 30 00 3 20 0 00 100 00 QP 3 332 01 8 19 19 21 27 40 37 00 9 60 0 00 387 90 QP 4 397 89 11 52 21 73 33 25 37 00 3 75 360 00 327 00 QP 5 501 46 4 57 23 55 28 12 37 00 8 88 0 00 199 30 QP 6 548 56 7 59 25 01 32 60 37 00 4 40 360 00 100 00 QP 7 876 01 4 06 29 74 33 80 37 00 3 20 8 90 100 00 QP REMARKS The other emission levels were very low against the limit Page 22 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Report No 81004101 E Environmental o S GER C 57 RH 6dB Bandwidth 120 kHz
20. TE TABLETOP EQUIPMENT The EUT installed in a representative system as described in section 7 of IEC 61000 4 3 was placed ona non conductive table 0 8 meters in height The system under test was connected to the power and signal wire according to relevant installation instructions FLOOR STANDING EQUIPMENT The EUT installed in a representative system as described in section 7 of IEC 61000 4 3 was placed on a non conductive wood support 0 1 meters in height The system under test was connected to the power and signal wire according to relevant installation instructions Page 42 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Report No 81004101 E 8 4 5 TEST RESULTS Humidity 53 RH Pressure 988mbar Dwell Time 3 sec Required Passing wees Tested By Eason Chen Peromnance CriterionA Field Frequency Performance MHz Polarity Azimuth 29 Criterion Observation Rest CEO eieiei sl bia DI vows Pass NOTE 1 There was no change compared with the initial operation during the test Page 43 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 5 ELECTRICAL FAST TRANSIENT EFT 8 5 1 TEST SPECIFICATION Basic Standard IEC 61000 4 4 Test Voltage AC Power Port 1kV DC Power Port 0 5kV Signal
21. ance loss then either of these may be derived from the product description and documentation and by what the user may reasonably expect from the equipment if used as intended After test the apparatus shell continues to operate as intended without operator intervention No degradation of performance or loss of function is allowed after the application of the phenomenon below a performance level specified by the manufacturer when the apparatus is used as intended The performance level may be replaced by a permissible loss of performance During the test degradation of performance is however allowed However no change of operating state if stored data is allowed to persist after the test If the manufacturer does not specify the minimum performance level or the permissible performance loss then either of these may be derived from the product description and documentation and by what the user may reasonably expect from the equipment if used as intended Temporary loss of function is allowed provided the functions is self recoverable or can be restored by the operation of controls by the user in accordance with the manufacturer instructions Functions and or information stored in non volatile memory or protected by a battery backup shall not be lost Page 32 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 3 E
22. anced three phase equipment Household appliances excluding equipment as Class D Tools excluding portable tools Dimmers for incandescent lamps audio equipment equipment not specified in one of the three other classes Class B Portable tools Arc welding equipment which is not professional equipment Class C Lighting equipment Class D Equipment having a specified power less than or equal to 600 W of the following types Personal computers and personal computer monitors and television receivers e The correspondent test program of test instrument to measure the current harmonics emanated from EUT is chosen The measure time shall be not less than the time necessary for the EUT to be exercised 7 4 4 TEST SETUP Harmonics amp Flicker Analyzer Power Source For the actual test configuration please refer to the related item Photographs of the Test Configuration 7 4 5 TEST RESULTS EUT max Power 64 18W Note According to clause 7 of EN 61000 3 2 equipment with a rated power of 75W or less no limits apply Page 25 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc HEET 7 5 VOLTAGE FLUCTUATION AND FLICKS MEASUREMENT 7 5 1 LIMITS OF VOLTAGE FLUCTUATION AND FLICKS MEASUREMENT P means short term flicker indicator Pi means long term flicker indicator st It Tameans maximum time that dt exceeds 3
23. cesatscnteaachententedaeisstadaadssinteedasteiardeaenanes 8 4 RADIATED RADIO FREQUENCY ELECTROMAGNETIC FIELD R I 8 5 ELECTRICAL FAST RT CH RE 8 6 SURGE IMMUNITY TES E 8 7 CONDUCTED RADIO FREQUENCY DISTURBANCES CES 8 8 POWER FREQUENCY MAGNETIC FIELD os cctcevassscndensincadtvaneesorcaseesddvenzeanieceedtvuanktencaasien 8 9 VOLTAGE DIP amp VOLTAGE INTERRUPTIONS vissccciitsccitnciieciias aid aaa PHOTOGRAPHS OF THE TEST CONFIGURATION 0ccccccsssseeeeessseeeeeeesneeeeeeeeeeenenees Page 3 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Report No 81004101 E Compliance Certification Services Inc ee ee 1 TEST CERTIFICATION Product 8 4 Rugged Tablet PC Model RO8I68M RTXXXX X A Z a z 0 9 Blank or Slash Brand Winmate Applicant Winmate Communication Inc 9F No 111 6 Shing De Rd San Chung City Taipei 241 Taiwan R O C Manufacturer Winmate Communication Inc 9F No 111 6 Shing De Rd San Chung City Taipei 241 Taiwan R O C Tested October 3 11 2008 Test Voltage 230VAC 50Hz Applicable EN 55022 2006 Class B EN 55024 1998 A1 2001 A2 2003 Standards EN 61000 3 2 2006 Class D IEC 61000 4 2 1995 A1 1998 A2 2000 EN 61000 3 3 1995 A1 2001 A2 2005 IEC 61000 4 3 2002 A1 2002 IEC 61000 4 4 2004 IEC 61000 4 5 1995 A1 2000 IEC 61000 4 6 1996 A1 2000 IEC 61000 4 8 1993 A1
24. d compare reading to the applicable limit Incase of measuring on the screened cable the current limit shall be applied otherwise the voltage limit should be applied The following test mode was scanned during the preliminary test No applicable because the EUT doesn t have LAN port or Modem port Page 17 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 7 2 4 TEST SETUP Be Test Receiver E d 30 cm to 80 cm gt 1 Distance to the ground reference plane vertical or horizontal 2 Distance to the ground reference plane is not critical For the actual test configuration please refer to the related item Photographs of the Test Configuration 7 2 5 DATA SAMPLE Ereduene QuasiPeak Average Correctrion QuasiPeak Average QuasiPeak Average QuasiPeak Average MHz y reading reading factor result result limit limit margin margin dBuV dBuV dB dBuV dBuV dBuV dBuV dB dB X XX 43 95 33 00 10 00 53 95 43 00 74 00 64 00 20 05 21 00 Pass Frequency MHz Emission frequency in MHz Reading dBuV Uncorrected Analyzer Receiver reading Insertion loss of LISN if it gt 0 5 dB Correction Factor dB ISN Factor Cable loss Result dBuV Raw reading converted to dBuV and CF added Limit dBuV Limit stated in standard Margin dB Result dBuV Li
25. ding on the Ground Reference Plane The GRP consisted of a sheet of aluminum at least 0 25mm thick and 2 5 meters square connected to the protective grounding system A Horizontal Coupling Plane 1 6m x 0 8m was placed on the table and attached to the GRP by means of a cable with 940k total impedance The equipment under test was installed in a representative system as described in section 7 of IEC 61000 4 2 and its cables were placed on the HCP and isolated by an insulating support of 0 5mm thickness A distance of 1 meter minimum was provided between the EUT and the walls of the laboratory and any other metallic structure FLOOR STANDING EQUIPMENT The equipment under test was installed in a representative system as described in section 7 of IEC 61000 4 2 and its cables were isolated from the Ground Reference Plane by an insulating support of 0 1 meter thickness The GRP consisted of a sheet of aluminum that is at least 0 25mm thick and 2 5 meters square connected to the protective grounding system and extended at least 0 5 meters from the EUT on all sides Page 35 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc See 8 3 5 TEST RESULTS Humidity 53 RH Pressure 998mbar Tested By Eason Chen Required Passing Performance Air Discharge Test Test Levels Results Points Performance Criterion 4 Performance Per
26. duction coils of suitable dimensions The test shall be repeated by moving and shifting the induction coils in order to test the whole volume of the EUT for each orthogonal direction The test shall be repeated with the coil shifted to different positions along the side of the EUT in steps corresponding to 50 of the shortest side of the coil The induction coil shall then be rotated by 90 degrees in order to expose the EUT to the test field with different orientations Page 53 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ee ee 8 8 5 TEST RESULTS Humidity 53 RH Pressure 998mbar Tested By Eason Chen Required Passing Performance DIRECTION SEENEN EE OBSERVATION RESULTS gem Criterion EN Ee KE NOTE 1 There was no change compared with the initial operation during the test Page 54 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc 8 9 VOLTAGE DIP amp VOLTAGE INTERRUPTIONS Report No 81004101 E 8 9 1 TEST SPECIFICATION Basic Standard IEC 61000 4 11 Test duration time Minimum three test events in sequence Interval between event Minimum 10 seconds Angle 0 360 degree Step 45 degree 8 9 2 TEST INSTRUMENT Immunity shielded room Name of Equipment Serial Number Calibration Due
27. formance Criterion Criterion LIB LIB Ca Ce LIA B LA CR LA CR bs e H lt n x lt e H lt a i i c gt c D e ogox Pi gt gt c Ww Oooo ogox gt gt gt c D CI O Contact Discharge Test Test Levels a Performance 4 Performance Performance Points Se Sene S Criterion Criterion Criterion Dia Ce LIB Ca CS LA B For the tested points to EUT please refer to attached page Blue arrow mark for Contact Discharge and red arrow mark for Air Discharge Discharge To Horizontal Coupling Plane Test Levels Reeuips Z O Side of EUT Performance K e JO XQ O Ka IB Notet K JO XQ O Ka LIB Notet K JO KQ O Ba B o Jo IS UI Ka B xH lt n xH lt SH NEES NEES Oog KK e ooo Sie KOR o Ww RW RW KA IB Notet Discharge To Vertical Coupling Plane Test Levels Resuits Z O Side of EUT Performance S 2kv Jam Lean Pass Fail EZ Observation K O ia LIB Meter K UU ia LIB Meter K O ia LIB Meter K O A _ I B_ Note4 _ _ NOTE 1 There was no change compared with initial operation during the test 2 The screen of EUT were slight flicker during the Air discharge but can auto recovered as the events disappear Page 36 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services I
28. guration consisted of a wooden table 0 8m high standing on the Ground Reference Plane The GRP consisted of a sheet of aluminum at least 0 25mm thick and 2 5m square connected to the protective grounding system A minimum distance of 0 5m was provided between the EUT and the walls of the laboratory or any other metallic structure FLOOR STANDING EQUIPMENT The EUT installed in a representative system as described in section 7 of IEC 61000 4 4 and its cables were isolated from the Ground Reference Plane by an insulating support that is 0 1 meter thick The GRP consisted of a sheet of aluminum at least 0 25mm thick and 2 5m square connected to the protective grounding system 8 5 5 TEST RESULTS Humidity 53 RH Pressure pmter Tested By Required Passing Performance Criterion B Test Point Polarity Wess i E Observation wm riterion se E a Ia o a e es Oce Ia D e e Ins vn Lal a e ams s Owe a e a e e ass NOTE 1 There was no change compared with initial operation during the test 2 The screen of EUT was slight flicker during the test but can auto recovered as the events disappear Page 45 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Report No 81004101 E 8 6 SURGE IMMUNITY TEST 8 6 1 TEST SPECIFICATION Basic Standard IEC 61000 4 5 Wave Shape Combination Wave 1 2 50 us Open Circuit Voltage 8
29. in full without the written approval of Compliance Certification Services Compliance Certification Services Inc HEET 8 4 3 TEST PROCEDURE please refer to measurement standard or CCS SOP PA 023 The test procedure was in accordance with IEC 61000 4 3 a The testing was performed in a fully anechoic chamber The transmit antenna was located at a distance of 3 meters from the EUT b The frequency range is swept from 80 MHz to 1000 MHz with the signal 80 amplitude modulated with a 1kHz sine wave The rate of sweep did not exceed 1 5 x 10 decade s where the frequency range is swept incrementally the step size was 1 of preceding frequency value CH The dwell time at each frequency shall be not less than the time necessary for the EUT to be able to respond e The test was performed with the EUT exposed to both vertically and horizontally polarized fields on each of the four sides Page 41 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 4 4 TEST SETUP 3 meter 7X3x3 EUT amp Support Units 1 5 meter 0 8m Power Amp EUT Monitoring by using a camera PC Controller to control S G amp PAas Signal Generator well as forward power Control Room For the actual test configuration please refer to the related item Photographs of the Test Configuration NO
30. ion Emission Radiated SE Mode 1 Emission Immunity Mode 1 Then the above highest emission mode of the configuration of the EUT and cable was chosen for all final test items 4 2 EUT SYSTEM OPERATION Setup the EUT and simulators as shown on 5 2 Turn on the power of all equipment EMI test program was loaded and executed in Windows XP mode Data was sent to the Panel of EUT and monitor and filling the screens with upper case of H patterns 5 Test program sequentially exercised all related I O s of EUT and sent H patterns to all applicable output ports of EUT 6 Repeat 3 to 5 SI OIN gt Note Test program is self repeating throughout the test Page 7 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc 5 SETUP OF EQUIPMENT UNDER TEST 5 1 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units The following support units or accessories were used to form a representative test configuration during the tests Report No 81004101 E Modem DM 1414 304012261 IFAXDM1414 ACEEX Unshielded 1 8m Unshielded 1 8m USB 6512 UV maa deii FCC DoC ACER Unshielded 1 8m Keyboard USB Mouse MO19UCA 020440953 FCC DoC Unshielded 1 8m Multimedia jc 5258MV 0507106337 F
31. l of Compliance Certification Services Compliance Certification Services Inc A O N TABLE OF CONTENTS TEST CE TE IC ATION DE TEST RESULT SUMMARY eetenetteeEueregien tte reueg BUT DESCRIPTION DE TEST METHODOLOGY EE 4 1 DECISION OF FINAL TES EH 4 2 EUT SYSTEM OPERA ION EG SETUP OF EQUIPMENT UNDER TEST wicsiescciccccsssssicensriciveccsnneneunsicavennseniseneniserenessvenunecene 5 1 DESCRIPTION OF SUPPORT UNITS ccittiscccsctrtsaisceteiars centienscarctetacanecebecadaietecavaionerniadcees 5 2 CONFIGURATION OF SYSTEM UNDER TES sscsccivssctcceresoueni even vadesainaeadeccaveu beeen FACILITIES AND ACCREDITATION S trsvisisicacranntraninssamatracensieniansemintianewnisamectnianebemibaouaene 6 1 TE RT 6 2 ACCREDITATIONS eegene snein anra K aane aa ESENE EEKE EAE ENES GEREENT AE HA EE EMISSION TES I iccssvcinednnaptancnicahinanaueuntanmieientnieesmunea sonata EEEeerg 7 1 CONDUCTED EMISSION MEAGUREMENT AA 7 2 CONDUCTED EMISSION MEASUREMENT AT TELECOMMUNICATION PORTG 7 3 RADIATED EMISSION MEASUREMENT vrcuascectenasats ncateienteadits scadecessataditapastccentueaditeenenents 7 4 HARMONICS CURRENT MEASUREMENT vspciveaslicryccthsal deat Qietvccsndoadiorteuteernde uetleetiteshes 7 5 VOLTAGE FLUCTUATION AND FLICKS MEASUREMENT 0 0 02 eeeeeeeeeeeeeeeeeeesneeeeeeenaes IMMUNITY TEST RE 8 1 GENERAL DESCRIPTION EE 8 2 GENERAL PERFORMANCE CRITERIA DESCHIDTION 8 3 ELECTROSTATIC DISCHARGE ESD cicctscccncsesccet
32. lyzer Receiver scanned from 30MHz to 1000MHz Emissions were scanned and measured rotating the EUT to 360 degrees varying cable placement and positioning the antenna 1 to 4 meters above the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level Recording at least the six highest emissions Emission frequency amplitude antenna position polarization and turntable position were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit and only Q P reading is presented The test data of the worst case condition s was recorded Page 20 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 7 3 4 TEST SETUP Test table amp Turntable Coaxial Cable Ground Plane Receiver For the actual test configuration please refer to the related item Photographs of the Test Configuration 7 3 5 DATA SAMPLE Frequency Reading BE Result Limit Margin Degree MHz dBuV dB m dBuV m dBuV m dB Frequency MHz Emission frequency in MHz Reading dBuV Uncorrected Analyzer Receiver reading Correction Factor dB m Antenna factor Cable loss Amplifier gain Result dBuV m Reading dBuV Corr Factor dB m Limit dBuV m Limit stated in standard
33. m a wooden table with a height of 0 8 meters is used and is placed on the ground plane as per EN 55022 see Test Facility for the dimensions of the ground plane used When the EUT is a floor standing equipment it is placed on the ground plane which has a 3 12 mm non conductive covering to insulate the EUT from the ground plane All UO cables were positioned to simulate typical actual usage as per EN 55022 The EUT installed by AC main power through a Line Impedance Stabilization Network LISN which was supplied power source and was grounded to the ground plane All support equipment power by a second LISN The test program of the EUT was started Emissions were measured on each current carrying line of the EUT using an EMI Test Receiver connected to the LISN powering the EUT The Receiver scanned from 150kHz to 30MHz for emissions in each of the test modes During the above scans the emissions were maximized by cable manipulation The test mode s described in Item 3 1 were scanned during the preliminary test After the preliminary scan we found the test mode described in Item 3 1 producing the highest emission level The worst configuration of EUT and cable of the above highest emission level were recorded for reference of the final test Procedure of Final Test EUT and support equipment were set up on the test bench as per the configuration with highest emission level in the preliminary test A scan was taken on both po
34. mit dBuV 7 2 6 TEST RESULTS No applicable because the EUT doesn t have LAN port or Modem port Page 18 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 7 3 RADIATED EMISSION MEASUREMENT 7 3 1 LIMITS FREQUENCY MHz dBuV m At 10m Class A Class B 30 230 40 30 230 1000 47 37 NOTE 1 The lower limit shall apply at the transition frequencies 2 Emission level dBuV m 20 log Emission level uV m 7 3 2 TEST INSTRUMENTS Name of Equipment Manufacturer Model Serial Number Calibration Due EMI Test Receiver 03 03 2009 Pre Amplifier 04 02 2009 Bilog Antenna 06 20 2009 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration Request Page 19 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ee 7 3 3 TEST PROCEDURE please refer to measurement standard or CCS SOP PA 031 Procedure of Preliminary Test The equipment was set up as per the test configuration to simulate typical usage per the user s manual When the EUT is a tabletop system a wooden turntable with a height of 0 8 meters is used which is placed on the ground plane When the EUT is a fl
35. mit stated in standard Margin dB Result dBuV Limit dBuV Page 13 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Report No 81004101 E 7 1 6 TEST RESULTS CCS Conduction Test 3 Model No No Model No RO8I68M RTXOX RTXXXX RO8I68M RTXXXX ep Bandwidth Bandwidth 6dB Bandwidth our kHz Environmental R 80 0 dBu QP AVG 5 8 g 40 0 0 0 150 0 5 MHz 5 30 000 QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average NO Frequency Remark reading reading factor result result limit limit margin margin MHz dBuV dBuV dB dBuV dBuV dBuV dBuV dB dB Pass Fail 1 0 1969 44 70 34 90 9 70 54 40 44 60 63 74 53 74 9 34 9 14 Pass 2 0 2672 38 50 32 10 9 70 48 20 41 80 61 20 51 20 13 00 9 40 Pass 3 0 4000 35 09 32 39 9 71 44 80 42 10 57 85 47 85 13 05 5 75 Pass 4 0 4664 34 86 33 76 9 64 44 50 43 40 56 58 46 58 12 08 3 18 Pass 5 0 7984 31 29 30 59 9 61 40 90 40 20 56 00 46 00 15 10 5 80 Pass 6 0 9977 33 49 32 29 9 61 43 10 41 90 56 00 46 00 12 90 4 10 Pass 7 1 3297 33 16 32 46 9 64 42 80 42 10 56 00 46 00 13 20 3 90 Pass 8 1 5953 30 82 29 72 9 68 40 50 39 40 56 00 46 00 15 50 6 60 Pass 9 1 9352 26 89 25 69 9 71 36 60 35 40 56 00 46 00 19 40 10 60 Pass REMARKS L1 Line One Live Line Page 14 This report shall not be reproduced exce
36. n Chen Required Passing Performance Test Point Polarity Mest Tove Ge SE Observation kV riterion NOTE 1 There was no change compared with initial operation during the test Page 48 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 7 CONDUCTED RADIO FREQUENCY DISTURBANCES CS 8 7 1 TEST SPECIFICATION Basic Standard IEC 61000 4 6 Frequency Range 0 15 MHz 80 MHz Field Strength 3 Vrms Modulation 1kHz Sine Wave 80 AM Modulation Frequency Step 1 of preceding frequency value Coupled cable Power Mains Unshielded Coupling device CDN M3 3 wires 8 7 2 TEST INSTRUMENT Immunity Shield Room Test S W EMS K1 V1 20 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration required Page 49 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 7 3 TEST PROCEDURE please refer to measurement standard or CCS SOP PA 026 The EUT shall be tested within its intended operating and climatic conditions The test shell performed with the test generator connected to each of the coupling and decoupling devices in turn while the other non excited RF input ports of the coupling devices
37. nc See The Tested Points of EUT Photo 1 of 5 Photo 2 of 5 Page 37 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg Photo 3 of 5 Photo 4 of 5 Page 38 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc see tae Photo 5 of 5 Page 39 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ee ee 8 4 RADIATED RADIO FREQUENCY ELECTROMAGNETIC FIELD RS 8 4 1 TEST SPECIFICATION Basic Standard IEC 61000 4 3 Frequency Range 80 MHz 1000 MHz Field Strength 3 V m Modulation 1kHz Sine Wave 80 AM Modulation Frequency Step 1 of preceding frequency value Polarity of Antenna Horizontal and Vertical Test Distance 3m Antenna Height 1 5m 8 4 2 TEST INSTRUMENT 733 RS Chamber Name of Equipment Manufacturer Model Serial Number Calibration Due Agilent 8648C 4108A05772 10 28 2008 NRVD 837794 029 08 04 2009 NOTE 1 The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML ROC and NIST USA 2 N C R No Calibration required URV5 Z2 835640 015 08 04 2009 Page 40 This report shall not be reproduced except
38. of Compliance Certification Services Compliance Certification Services Inc SE 7 5 5 TEST RESULTS Observation Environmental 23 C 45 RH Tested By Eason Chen Conditions Power Continuity MEASUREMENT TEST PARAMETER VALUE LMT REMARK Li In 1 me IL me Power Switched Manually MEASUREMENT 0 072 PASS de 0 17 PASS Note dmax limit classified 1 6 for equipment which is switched manually or switched automatically more frequently than twice per day 2 7 for equipment which is attended whilst use or switched on automatically no more than twice per day Page 28 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg Winmate Date 2008 10 11 PM 02 0 V4 16 Operator Eason Chen Unit 8 4 Rugged Tablet PC Serial number RO8I68M RTXXXXX Remarks Temp 23 Hemid 45 Power Continuity Urms 229 9V Freq 49 987 Range 5A Irms 0 598A Ipk 2 432A cf 4 065 P 64 18W S 137 5VA pf 0 467 Test Time 1 x 10min 10min 100 Si LIN Line Impedance Network L 0 24ohm j30 150hm N 0 16o0hm 30 100hm Limits BIR 3 065 Pst 7 12 00 dmax 4 00 dc 13 30 dtLim 3 30 dt gt Lim 500ms Test completed Result PASSED Plt 0 072 Pst dmax dc dt gt Lim Fail 5 5 ms 1 0 072 0 000 0 010 0 000 Page 29 This report shall not be reproduced except in full withou
39. oid possible adverse effects on equipment not under test that may be powered by the same lines and to provide sufficient decoupling impedance to the surge wave The power cord between the EUT and the coupling decoupling networks was shorter than 2 meters in length For test applied to unshielded un symmetrically operated interconnection lines of EUT The surge was applied to the lines via the capacitive coupling The coupling decoupling networks didn t influence the specified functional conditions of the EUT The interconnection line between the EUT and the coupling decoupling networks was shorter than 2 meters in length For test applied to unshielded symmetrically operated interconnection telecommunication lines of EUT The surge was applied to the lines via gas arrestors coupling Test levels below the ignition point of the coupling arrestor were not specified The interconnection line between the EUT and the coupling decoupling networks was shorter than 2 meters in length 8 6 4 TEST SETUP To AC Source Surge Immunity EUT amp Support Units Controller Computer For the actual test configuration please refer to the related item Photographs of the Test Configuration Page 47 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ee ee 8 6 5 TEST RESULTS Humidity 53 RH Pressure 988mbar Tested By Easo
40. oor standing equipment it is placed on the ground plane which has a 3 12 mm non conductive covering to insulate the EUT from the ground plane Support equipment if needed was placed as per EN 55022 All UO cables were positioned to simulate typical usage as per EN 55022 The EUT received AC power source from the outlet socket under the turntable All support equipment power received from another socket under the turntable The antenna was placed at 10 meter away from the EUT as stated in EN 55022 The antenna connected to the Spectrum Analyzer via a cable and at times a pre amplifier would be used The Analyzer Receiver quickly scanned from 30MHz to 1000MHz The EUT test program was started Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4 meters above the ground plane in both the vertical and the horizontal polarization to maximize the emission reading level The test mode s described in Item 3 1 were scanned during the preliminary test After the preliminary scan we found the test mode described in Item 3 1 producing the highest emission level The worst configuration of EUT and cable antenna position polarization and turntable position of the above highest emission levels were recorded for the final test Procedure of Final Test EUT and support equipment were set up on the turntable as per the configuration with highest emission level in the preliminary test The Ana
41. oval of Compliance Certification Services Compliance Certification Services Inc 6 3 MEASUREMENT UNCERTAINTY Report No 81004101 E Where relevant the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16 4 2 Conducted emissions 9kHz 30MHz 1 7806 N 30 200MHz 3 8856 Radiated emissions 200 1000MHz 3 8721 This uncertainty represents an expanded uncertainty expressed at approximately the 95 confidence level using a coverage factor of k 2 Consistent with industry standard e g CISPR 22 2006 clause 11 Measurement Uncertainty determining compliance with the limits shall be base on the results of the compliance measurement Consequently the measure emissions being less than the maximum allowed emission result in this be a compliant test or passing test The acceptable measurement uncertainty value without requiring revision of the compliance statement is base on conducted and radiated emissions being less than Ucispr which is 3 6dB and 5 2dB respectively CCS values called Ura in CISPR 16 4 2 is less than Ucispr as shown in the table above Therefore MU need not be considered for compliance Page 10 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc 7 EMISSION TEST 7 1 CONDUCTED EMISSION MEASUREMENT Report No 81004101 E 7 1 1 LIMITS
42. points shall each receive at least 50 direct contact discharges If no direct contact test points are available then at least 200 indirect discharges shall be applied in the indirect mode Test shall be performed at a maximum repetition rate of one discharge per second Air discharges at slots and apertures and insulating surfaces On those parts of the EUT where it is not possible to perform contact discharge testing the equipment should be investigated to identify user accessible points where breakdown may occur Such points are tested using the air discharge method This investigation should be restricted to those area normally handled by the user A minimum of 10 single air discharges shall be applied to the selected test point for each such area The basic test procedure was in accordance with IEC 61000 4 2 a b ao xw 2 Q The EUT was located 0 1 m minimum from all side of the HCP dimensions 1 6m x 0 8m The support units were located another table 30 cm away from the EUT but direct support unit was were located at same location as EUT on the HCP and keep at a distance of 10 cm with EUT The time interval between two successive single discharges was at least 1 second Contact discharges were applied to the non insulating coating with the pointed tip of the generator penetrating the coating and contacting the conducting substrate Air discharges were applied with the round discharge tip of the discharge elect
43. pt in full without the written approval of Compliance Certification Services Compliance Certification Services Inc See CCS Conduction Test 3 Model No RO8I68M RT XXXX 6dB Bandwidth 9 kHz Environmental a ge Tested By Eason Chen Line L2 80 0 dBu QP AVG 3 gt 7 40 0 0 0 150 0 5 MHz 5 30 000 QuasiPeak Average Correction QuasiPeak Average QuasiPeak Average QuasiPeak Average NO Frequency Remark reading reading factor result result limit limit margin margin MHz dBuV dBuV dB dBuV dBuV dBuV dBuV dB dB Pass Fail 1 0 2008 43 30 35 20 9 10 52 40 44 30 63 58 53 58 11 18 9 28 Pass 2 0 2672 36 60 31 40 9 30 45 90 40 70 61 20 51 20 15 30 10 50 Pass 3 0 3961 32 22 29 12 9 68 41 90 38 80 57 93 47 93 16 03 9 13 Pass 4 0 4664 34 78 33 38 9 62 44 40 43 00 56 58 46 58 12 18 3 58 Pass 5 0 9977 32 30 31 30 9 60 41 90 40 90 56 00 46 00 14 10 5 10 Pass 6 1 3375 27 67 26 27 9 63 37 30 35 90 56 00 46 00 18 70 10 10 Pass 7 1 5992 31 73 30 83 9 67 41 40 40 50 56 00 46 00 14 60 5 50 Pass REMARKS L2 Line Two Neutral Line Page 15 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 7 2 CONDUCTED EMISSION MEASUREMENT AT TELECOMMUNICATION PORTS 7 2 1 LIMITS For Class A Equipment FREQUENCY ome Voltage Limit dBuV Current Limit dBuA FREQUENCY MHz 0 15 0 5 97 87 84
44. rode approaching the EUT as fast as possible without causing mechanical damage to touch the EUT After each discharge the ESD generator was removed from the EUT and re triggered for a new single discharge The test was repeated until all discharges were complete At least ten single discharges in the most sensitive polarity were applied at the front edge of each HCP opposite the center point of each unit of the EUT and 0 1 meters from the front of the EUT The long axis of the discharge electrode was in the plane of the HCP and perpendicular to its front edge during the discharge At least ten single discharges in the most sensitive polarity were applied to the center of one vertical edge of the Vertical Coupling Plane VCP in sufficiently different positions that the four faces of the EUT were completely illuminated The VCP dimensions 0 5m x 0 5m was placed vertically to and 0 1 meters from the EUT Page 34 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 8 3 4 TEST SETUP 10cm VCP 0 5 mm Thick Support Insulator EUT units pe ENE oe S O Vi Wooden Table 470 KQ B For the actual test configuration please refer to the related item Photographs of the Test Configuration Ground Reference Plane NOTE TABLE TOP EQUIPMENT The configuration consisted of a wooden table 0 8 meters high stan
45. t the written approval of Compliance Certification Services Compliance Certification Services Inc EE Winmate Date 2008 10 11 PM 03 2 V4 16 Operator Eason Chen Unit 8 4 Rugged Tablet PC Serial number RO8I68M RTXXXXX Remarks Temp 23 Hemid 45 Power Switched Manually Urms 230 1V Freq 49 987 Range 5A Irms 0 269A Ipk 1 189A cf 4 427 P 26 87W S 61 80VA pf 0 435 Test Time 1 x 10min 10min 100 Si LIN Line Impedance Network L 0 24ohm j30 150hm N 0 16o0hm 30 100hm Limits BIR 3 065 Pst 7 12 00 dmax 4 00 dc 13 30 dtLim 3 30 dt gt Lim 500ms Test completed Result PASSED Plt 0 072 Pst dmax dc dt gt Lim Fail 5 5 ms 1 0 072 0 060 0 170 0 000 Page 30 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc eee nine 8 IMMUNITY TEST 8 1 GENERAL DESCRIPTION Product EN 55024 1998 A1 2001 A2 2003 Standard Test Type Minimum Requirement IEC 61000 4 2 Electrostatic Discharge ESD 8kV air discharge 4kV Contact discharge Performance Criterion B IEC 61000 4 3 Radio Frequency Electromagnetic Field Susceptibility Test RS 80 1000 MHz 3V m 80 AM 1kHz Performance Criterion A IEC 61000 4 4 Electrical Fast Transient Burst EFT AC Power Port 1kV DC Power Port 0 5kV Signal Ports and Telecommunication Ports 0 5kV Performance Criterion B
46. uirements of Performance Criterion A RS IEC 61000 4 4 2004 PASS Meets the requirements of Performance Criterion B IEC 61000 4 5 1995 A1 2000 PASS Meets the requirements of Performance Criterion B IEC 61000 4 6 1996 A1 2000 PASS Meets the requirements of Performance Criterion A IEC 61000 4 8 1993 A1 2000 PFMF PASS Meets the requirements of Performance Criterion A variations Voltage Interruptions 1 gt 95 reduction Performance Criterion C Meets the requirements of Voltage Voltage Dips dips amp 1 gt 95 reduction Performance Criterion B ES IO aT aoe voltage PASS 2 30 reduction Performance Criterion C Note 1 The statements of test result on the above are decided by the request of test standard only the measurement uncertainties are not factored into this compliance determination 2 The information of measurement uncertainty is available upon the customer s request Page 5 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ee re A EUT DESCRIPTION Product 8 4 Rugged Tablet PC Brand Name Winmate Model RO8I6G8M RTXXXX X A Z a z 0 9 Blank or Slash Applicant Winmate Communication Inc Serial Number 81004101 Received Date October 3 2008 EUT Power Rating 19VDC 3 42A Power Adapter Manufacturer FSP Model FSP065 AAB I P 100 240VAC 50 60Hz 1 5A O P 19VDC 3 42A AC
47. wer lines Line 1 and Line 2 recording at least the six highest emissions Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit The test data of the worst case condition s was recorded Page 12 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Sg 7 1 4 TEST SETUP Vert reference plane A EMI receiver O O EUT n Aa O d 80cm V LISN Sa Reference ground plane 40cm For the actual test configuration please refer to the related item Photographs of the Test Configuration 7 1 5 DATA SAMPLE F QuasiPeak Average Correctrion QuasiPeak Average QuasiPeak Average QuasiPeak Average requency S S Ste SE b S MHz reading reading factor result result limit limit margin margin dBuV dBuV dB dBuV dBuV dBuV dBuV dB dB X XX 43 95 33 00 10 00 53 95 43 00 56 00 46 00 Pass Frequency MHz Emission frequency in MHz Reading dBuV Uncorrected Analyzer Receiver reading Insertion loss of LISN if it gt 0 5 dB Correction Factor dB LISN Factor Cable loss Result dBuV Raw reading converted to dBuV and CF added Limit dBuV Li
48. wes Ga CB Jc NOTE 1 The screen of EUT was slight flicker but can auto recovered as the events disappear D OB ER 2 There was no change compared with initial operation during and after the test No unintentional response was found during the test 3 The function stopped during the test but can be recoverable manually after the test Page 56 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc SE 9 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Page 57 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Se RADIATED EMISSION TEST Page 58 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc EEN POWER HARMONIC amp VOLTAGE FLUCTUATION FLICKER TEST Page 59 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc ete ELECTROSTATIC DISCHARGE TEST Page 60 This report shall not be reproduced except in full without the written approval of Compliance Certification Services Compliance Certification Services Inc Report No 81004101 E RADIATED ELECTROMAGNETIC F

CE EMC TEST REPORT

Contents

Download Pdf Manuals

Related Search

Related Contents