CHOCOLATE FOUNTAIN USER GUIDE
Contents
1. S TU VVVVV VN VV VV VW Sa 2d 2c 2b 2a 9 13 FOUNTAIN ASSEMBLY 51 501 will be launched in August 2010 FOUNTAIN ASSEMBLY 502 Step 1 Remove fountain components from their cases and place fountain drum on a sturdy level surface Make sure the drum is level so that the chocolate will flow properly Step 2 Place the basin on top of the drum at an angle and push down and turn clockwise 45 degrees to lock the basin with drum To check the fountain is level place a spirit level on the basin rim at various locations Fig 1 If leveling is needed raise or lower a particular side of the fountain by adjusting the feet Step 3 Place metal screw on top of the square center shaft in the middle of basin Fig 2 Step 4 Place the center column on the four pins in the center of the fountain base Fig 3 Step 5 Place the Tiers on the center column Large one first then the medium dish and the small dish last Fig 4 Step 6 Place the top hat on top of the center column making sure that the metal screw pin sits in the middle of the top hat ring Fig 2 Fig 3 FOUNTAIN ASSEMBLY 503 Step 1 Remove fountain components from their cases and place fountain drum on a sturdy level surface Make sure the drum is level so that the chocolate will flow properly Step 2 Place the basin on top of the drum at an angle and push down and turn clockwise 45 degrees to lock2. B JMPosner N For Professional Caterers CHOCOLATE FOUNTAIN USER GUIDE This manual covers the use of the following commercial fountain models SQ1 502 503 THIS PAGE IS INTENTIONALLY BLANK Fountain Specifications Total Fountain Height Chocolate Capacity Total Fountain Weight Tier Set Weight Base Weight WARNING Please refer to important information regarding bearing servicing of this Chocolate Fountain contained in your user manual and warranty In essence this requires that the Chocolate Fountain has it s bearings serviced every 800 hours or one year whichever comes first Failure to do this may result in the invalidation of your warranty GENERAL INFORMATION The main problem of insufficient servicing is The seals located in the removal bowl may fail which will allow chocolate to leak into the motor compartment and cause the motor and other components to fail To reduce the risk of problems and to test whether the machine requires a service Please take note of the following points Never wash the removable bowl in the dishwasher The steam and hot water can cause premature failure of the seals and rusting of the bearings Always wash in the sink and do not fully submerge Every time you clean the fountain and remove the bowl try turning the spindle by hand This should move freely if it does not then machine needs to be serviced Once
3. The attendant should serve each guest by dipping the requested food item into the flowing chocolate and then serving the item to the guest on a plate A separate skewer is to be used with each food item Food items should never be doubled dipped in the chocolate after coming into contact with a guest s hand or mouth Guests should never touch the chocolate with their hands etc Guests should never introduce anything into the chocolate other than that which has been provided by the caterer Leftover chocolate remaining in the fountain at the end of each event should be disposed of and not reused Cleanliness All JM Posner Chocolate Fountain components are made of high quality 304 food grade stainless steel Any components that come into contact with chocolate must be cleaned thoroughly after every use The tier set components Center columns tiers top hat and screws are all dishwasher safe and should first be washed with warm soapy water after each use with care to avoid getting water on or inside the fountain housing It is also recommended that a sanitizing agent be used after the fountain components have been washed 23 24
4. Food item should only be dipped in the fondue once Cut all dipping items into bite size pieces so they can easily be placed on the skewers Never allow water to come into contact with chocolate as it can thicken and ruin the chocolate This includes water based flavorings and food colorings Use oil based products instead Keep chocolate in a cool dry place Do not freeze or refrigerate it as moisture may adversely affect the chocolate Always reduce the temperature setting from the melting temperature to the operating temperature once the chocolate is completely melted in the basin Failure to do so may cause the chocolate to scorch Do no add more than the maximum amount of fondue chocolate to the fountain basin If too much is added it will overflow the basin when the fountain is turned off Air is often trapped in the cylinder and at the bottom of the Top Hat when the fountain is initially turned on This can cause uneven chocolate flow To correct this simply turn the fountain off wait 15 30 seconds to allow the air to escape and turn it again Repeat until flow improves If air pockets are present at the base of the crown take a rubber spatula and scrape around the area to release the air If you are not using JM Posner Fountain Chocolate you will likely need to thin your chocolate according to the directions under CHOCOLATE PREPARATION Cocoa butter may also be used When cleaning up after an off site event place fount
5. Not enough chocolate Refer to the RECOMMENDED CHOCOLATE AMOUNTS table to ensure that you are meeting the minimum capacity requirement d Chocolate is too thick Chocolate will not flow correctly if it is at the wrong temperature Generally for Dark chocolate the temperature should be increased For White and Milk chocolate the temperature should be decreased Please see CHOCOLATE OPERATING TEMPERATURES for appropriate temperatures 6 Food blocking fondue flow Turn the motor off and use a spatula to check for food items that may have become lodged between the bottom of the cylinder and the basin f Small food particles in the fondue Small pieces of food flowing in the fondue may cause gaps as the pieces flow over the tiers Turn the motor off and try to remove the food with a spatula or strainer 2 Chocolate is thick and lumpy White and Milk chocolate are especially susceptible to overheating When over heated chocolate thickens and becomes lumpy To correct this stir small amounts of vegetable oil or cocoa butter into the chocolate until it reaches the appropriate consistency Chocolate may also be placed in a blender and mixed with the thinning agents Consult CHOCOLATE OPERATING TEMPERATURES to ensure you are using the appropriate temperature To avoid scorching stir the chocolate occasionally with a spatula scraping it from the bottom of the basin as you stir Chocolate will also become lumpy if it has come into contact w
6. least 10 minutes Step 2 JM Posner Fondue chocolate can either be pre melted or melted directly in the fountain To pre melt follow the instructions on the microwave below To melt in the fountain add 1kg of chocolate at a time stirring occasionally until completely melted To add chocolate to the fountain during use either pre melt the chocolate or pour 1 cup of chips at a time directly in to the basin Allow chips to melt before adding more Important Note Do not overfill the fountain see fountain capacities below Fountain Capacities 501 2kg 4kg Step 3 Once the chocolate is completely melted lower the heat by pressing the L 2 key to the operating temperature and turn the motor switch G5 to Temperature Settings Chocolate Type Melting C Operating C Milk 70 65 White 65 65 Important information about the Control Panel The control system switches the chocolate heater on and off such as to maintain the temperature at a pre set level and switches the motor on and off as required There is a two digit LED display to indicate the temperature in degrees Centigrade and also two individual LED indicators which light when the heater and motor respectively are on A membrane switch panel has a pair of push button switches for UP and DOWN L control of the temperature and a third push button commands the ON OFF state of the motor 1 SETTING THE TEMPERATURE When either
7. washed with warm soapy water and a large sponge Use a degreasing agent when washing components in the sink Make sure the chocolate is broken up by warm soapy water before it goes down the drain Chocolate poured directly down the drain may harden in the pipes and damage the drain system Twist off the removable basin and pour the leftover chocolate into a bag lined container for easy disposal Scrape the remaining chocolate out with a spatula Never pour chocolate directly down the drain Clean the basin of the fountain by hand with warm soapy water and a large sponge Carefully clean around the collar and center pin in basin If necessary use a soft toothbrush to remove all chocolate Spray the outside of the fountain base with stain less steal cleaner and polish with a soft cloth TROUBLESHOOTING 1 Chocolate does not curtain properly a Fountain is not level The base of the fountain must be level in order for chocolate to curtain properly If the fountain is flowing heavily on one side raise that side of the fountain using the adjustable feet until it flows evenly b Air bubbles Air is often trapped inside the cylinder when the fountain is initially turned on or if the chocolate level in the basin becomes too low This causes gaps in the chocolate curtain To resolve this simply turn the fountain off allow it to sit for 15 30 seconds and turn it back on Repeat this procedure until the fountain is flowing at full capacity c
8. 00 people Buy adding one extra bag of 2 5Kg chocolate you can serve and extra 200 people Based on single dippings see Fountain Capacities above Q Dol need to melt the chocolate before adding it to the fountain A Depending on how much chocolate you are adding it may need to be pre melted Please see ADDING ADDITIONAL CHOCOLATE TO THE FOUNTAIN Q Does the fountain need to be serviced regularly A Yes Please see MAINTENANCE Servicing is required every 800 hours use or 1 year Q Where do I go for replacement parts A Please call JM Posner on 44 0 208 421 9482 22 HEALTH AND SANITATION GUIDELINES JM Posner is committed to helping its customers provide the public with a healthy and sanitary environment in which to enjoy the JM Posner Chocolate Fountain at their special events JM Posner encourages its customers to comply with the following recommended Health and Sanitation Guidelines 1 Sanitary Use of the Chocolate Fountain A healthy and sanitary environment must be ensured with each use of the chocolate fountain A trained attendant must accompany the chocolate fountain at every event The attendant s responsibility is to operate the fountain and ensure that each guest at the event follows the proper Health amp Safety procedures below Everyone involved in the handling and preparation of food items should be Food Handler Certified by the local health agency The attendant must also be Food Handler Certified
9. able specifically for use with this fountain is not recommended by the manufacturer and may cause injury and will void your warranty Extreme caution must be used when moving a fountain or fountain components containing hot liquid Always move the fountain by lifting the drum If you lift the basin it might come off from the drum Use of the fountain outdoors is not recommended unless used with a Wind Guard Do not use this fountain for other than its intended use The Fountain must be on a level surface to operate properly Observe and follow customary sanitation guidelines when using this machine FOUNTAIN ASSEMBLY INSTRUCTIONS FOUNTAIN COMPONENTS 1 2 9 o N DH 5 w 10 11 12 13 Top Hat Fits on top of the center column and holds the metal screw in the middle Tiers 3 different sizes slides down the center column to rest into place a Small Tier Top b Medium Tier Middle c Large Tier Bottom d Extension Tier Smallest supplied with 5 extension purchased separately 5 Extension Piece You have to purchase this separately Center Column extension Rests on top of the centre column Where the middle top tiers sits Center Column Rests on top of the 4 pins in the middle of the basin Auger Extension Sits on top of the metal screw inside the center column extension Auger Sits on the square metal shaft in the middle of the basin inside the center column Steady Pins Su
10. ain parts in plastic bags and return them to the storage cases until they can be properly cleaned CLEANING THE FOUNTAIN Recommended Cleaning Supplies e Food handler gloves e Paper towels and soft cloth e Spatula s e Large container or sturdy plastic bag s for leftover chocolate e Ladle 9 Washing up liquid 9 Large sponge e Small brush or toothbrush e Stainless steel polish Before cleaning Always unplug the power cord form the electrical outlet before cleaning the fountain Never permit the electrical cord to come into contact with water Do not use abrasive scouring pads or powders to clean the stainless steel basin or other components Doing so will mar the finish To clean 1 Wearing food handler gloves scrape excess chocolate from the top hat and top amp middle tiers with a spatula Remove remove top hat and top amp middle tiers and place them directly in the sink Pull out the extension center column out of the center column scrapping the excess chocolate off with a spatula or gloved hand as you go so that it falls back into the Basin Move the extension center column to the sink Remove the Auger extension and scrapping the excess chocolate off Place them directly in the sink Use a spatula to scrape excess chocolate from the bottom tier auger and center column Remove the tier center column and metal screw and place them in the sink All removable fountain parts are dishwasher safe They may also be hand
11. ase This service schedule should be followed every 800 hours the fountain has been in use This scheduled maintenance service IS NOT covered by the warranty and there is a charge associated with this service The service will include the replacement of those parts subject to normal wear and tear that are described above Failure to adhere to the scheduled maintenance plan may void the warranty on the motor should it be damaged due to failure of the other components that have been worn through use WARRANTY LIMITATIONS AND EXCLUSIONS This limited warranty replaces all other warranties express or implied including but not limited to the implied warranties of merchant ability non infringrent and fitness for a particular purpose JM Posner makes no express warranties beyond those stated here JM Posner disclaims all other warranties expressed or implied including without limitation implied warranties of merchantability non infringement and fitness for a particular purpose The JM Posner limited warranty and any implied warranties that may apply extend only to the original purchase of the specific JM Posner products as identified by serial number and remain in force only as long as such purchaser owns the fountain Some countries do not allow the exclusion of implied warranties so this limitation may not apply to you If these laws apply then all express and implied warranties are limited in duration to the limited warranty period no warranti
12. es apply after that period Some countries do not allow limitations on the duration of an implied warranty so this limitation may not apply to you LIMITATION OF LIABILITY JM Posner s responsibility under this or other warranty implied or express is limited to the providing of replacement components for repair of the product purchased as set forth above These remedies are the sole and exclusive remedies for any breach of warranty You the purchaser agree and acknowledge that JM Posner has no liability and shall not be responsible for any damage you may incur from non receipt of the fountain or its construction or any other cause whether liability is asserted in contract tort or otherwise JM Posner is not responsible for indirect special incidental or consequential damages of any kind resulting from any breach of warranty or under any other legal theory including but not limited to lost profits downtime goodwill or damage to or replacement of equipment and property HOW TO OBTAIN WARRANTY SERVICE If any component of the Fountain proves to be defective during the warranty period applicable to such component contact our Customer Service Department to make arrangements for warranty service and for the location of the nearest certified JM Posner repair service provider Please be prepared to provide 1 your name address and telephone number 2 Proof of Purchase 3 a description of the defect believed by you to be covered by this Li
13. ith water 3 The fountain will not heat properly a Electrical problem Make sure that the fountain is plugged into a working electrical outlet and that the switch is in the ON or PREHEAT position If you have another appliance plugged into the same outlet the fountain may not be receiving enough electricity b Sensor Fault Check the fountain display if it says SF Please call our JM Posner Customer Service Department for further assistance c Loose wiring Unplug the fountain turn it over and remove the protective base net Check to see that all of the wires and contacts are firmly in place TROUBLESHOOTING cont 4 The fountain will not turn on a Bad electrical connection Power may have been interrupted by an electrical breaker being tripped Check power is being received by the fountain b Fuse has blown Replace the fuse The machine has 3 fuses 1st fuse is in the power cord 2nd fuse is in the power socket on the drum and the 3rd fuse is on the PCB board inside the drum You will need a qualified electrician to replace the fuse in the PCB board c Low Temperature Check the fountain display if it says LT this means the temperature of the fountain is not enough to start the motor Wait till the fountain temperature to raise to the set limit and then turn on the fountain 5 The fountain makes a knocking noise a Upon starting the fountain the metal screw may knock for about 30 seconds before the chocolate has co
14. mited Warranty 4 JM Posner Fountain model and serial number To reach a Customer Service Center please call 020 8421 9482 UK or E mail admin jmposner co uk After you have contacted our offices and discussed the nature of the claimed warranty defect JM Posner may require you to return the Fountain to a specified authorized service center for inspection and Warranty Service or may authorize you in writing to obtain service from an authorized technician in your area JM Posner or its designated service center in its sole discretion will determine after inspection if the defect developed under normal and proper use and the availability of coverage under this warranty Provided the defective component s are catered we reserve the right to use reconditioned or refurbished serviceable used parts which meet JM Posner s quality standards for warranty repair replacement or adjustment of the defective components shall be JM Posner s sole obligation and the customer s sole remedy hereunder The Warranty Service provided will restore the Fountain to normal operating condition and JM Posner has no liability to update any Fountain presented for Warranty Service with any internal or external design or modification which JM Posner had made to its Fountains after the date you purchased the Fountain covered by this warranty You are responsible and shall pay for all shipping costs required to obtain Warranty Service You are responsible for ensuring that the Fo
15. mperature then falls to T lt TSET 1 the heater and indicator are switched ON again Thus the hysteresis band is 2 C If the temperature sensor fails or is un plugged from the control board the heater and the motor are both switched OFF and the display shows SF Sensor Fault 3 MOTOR CONTROL When the fountain is switched on the motor is always in the OFF state initially and the Motor LED is off The motor subsequently runs ON when the push button is pressed and the Motor LED is illuminated Subsequent operation of the push button toggles the motor and indicator between the ON and states However if when the motor is commanded to be ON the chocolate bowl temperature T is less than 10 C the motor is inhibited and does not start In this event the display shows LT Low temperature for two seconds before it reverts to the normal temperature indication This is to minimize possible overheating of the motor winding as there is a risk of the Auger being locked due to solid chocolate The motor also has a built in thermal switch which opens if its temperature exceeds a safe limit This switch connects back to the controller to override normal motor operation Whenever the thermal switch is open the motor drive is set to OFF and the display shows OL Over Load until the motor has cooled sufficiently to reset the thermal switch The motor can then be re started manually by using the push b
16. mpletely coated the inside of the Center column b If knocking is coming from the cylinder When the fountain starts up the auger may knock against the cylinder momentarily until the chocolate has coated the inside cylinder walls and auger If knocking continues make sure the stabilizer is correctly positioned at the top of the cylinder around the auger knob so the auger is held in the center of the cylinder Also check to see that the cylinder is resting firmly in the basin collar c Chocolate is too thick If you are using JM Posner Fondue Chocolate make sure you are running it at the correct temperature If you are not using JM Posner chocolate you will need to thin it out with oil For any further troubleshooting questions or concerns please contact JM Posner s Customer Service Department at Tel 0044 0 20 8421 9482 20 FREQUENTLY ASKED QUESTIONS Q Are the fountain components dishwasher safe A Yes all removable fountain tier set parts and components may be washed in a dishwasher However please note DO NOT wash the bowl in the Dishwasher as this will cause damage Q What temperatures should the fountain be set to suite the different types of chocolate A Please see the CHOCOLATE OPERATING TEMPERATURE table Q Can leftover chocolate be re used A Yes but for sanitation reasons it is not recommended Q Can JM Posner Fondue Chocolate be ordered online A Yes Please visit us online at www jmposner co uk for
17. of the or push buttons is pressed the system enters the temperature setting mode and the display shows the existing unchanged set point temperature The two display decimal points flash on alternately to confirm that the temperature setting mode is enabled Further presses of the or push buttons cause the temperature to be increased or decreased respectively by 1 C at a time but if either push button is held for longer than two seconds the temperature is raised or lowered continuously at a rate of 3 C per second for as long as the push button is held If the temperature reaches 99 C further use of the push button cannot alter the temperature further nor if the temperature reaches 0 C the push button will note have any effect note that setting a temperature below the ambient temperature is irrelevant as the system only has a heater If neither push button is operated for longer than three seconds the system automatically comes out of the temperature setting mode and the flashing decimal points turn off At the same time the final set temperature value TSET is stored in non volatile memory this value will be retrieved and subsequently used when the fountain is next switched on 2 TEMPERATURE CONTROL When the fountain is switched on the heater is always in the ON state initially and the Heater LED is illuminated When the temperature has risen to T gt TSET the heater and its indicator LED are switched OFF When the te
18. pecifically for the providing of replacement components which have been determined to have been defective in materials or workmanship during the five year warranty period and does not cover the costs of labour that may be associated with the repair of the Fountain Notwithstanding the foregoing labour charges are covered for a period of five years only if the Fountain is serviced within the United Kingdom Should a replacement component be needed before end of the initial five year period The Purchaser will be responsible for all shipping costs required to obtain Warranty Service This Warranty is void and of no force or effect if the Fountain purchased has been tampered with repaired disassembled changed altered or modified by you or any other persons who have not been authorized in writing by JM Posner to make such repairs This warranty is also void if a voltage converter device is unused Excluded from this warranty are damages or defects which resulted from Other than normal and proper use normal wear and tear abuse damage accident impact misuse negligence improper maintenance non performance of schedule operator maintenance items or storage contamination and deterioration due to water or other liquids sand insect infestation or acts of God In order to ensure optimum performance of your JM Posner Fountain it must be serviced by an authorized service center after approximately 800 hours of operation or one year from the date of purch
19. pports center column Fixed to fountain basin Removable Basin Which sits on top of the drum and holds the center column and screw Do not place it in the dish washer Drum This is the bottom of the fountain Has all the electrical components including the motor unit Only to be opened by a qualified person a The vent holes allow hot air produced by the motor and heating elements to escape cooling the electrical components Vent holes should not be covered during use Membrane Switch The control system switches the chocolate heater on and off to maintain the temperature at a pre set level and switches the motor on and off as required There is a two digit LED display to indicate the temperature in degrees Centigrade and also two individual LED indicators which light when the heater and motor respectively are ON The membrane switch panel has a pair of push button switches for UP and DOWN control of the temperature and a third push button commands the ON OFF state of the motor Fuse The machine has 3 fuses 1st fuse is in the power cord 2nd fuse is in the power socket on the drum and the 3rd fuse is on the PCB board inside the drum Only a qualified electrician should replace the fuse in the PCB board Adjustable Feet Screw into the bottom of the base These may be tightened or loosened to raise or lower a particular side of the fountain for leveling ho
20. proximately 60 minutes Add chocolate 1kg at a time to expedite the melting process Stir chocolate occasionally scraping it from the basin with a spatula as you go this will prevent scorching Milk and White chocolate are more susceptible to burning so be sure to stir more frequently every 2 3 minutes and use appropriate temperature settings MELTING CHOCOLATE IN FOUNTAIN BASIN Temperature Settings Approx Melting Time Chocolate Type Heat Setting 45 mins 60 mins 75 mins 45 mins 60 mins 75 mins 45 mins 60 mins 75 mins CAUTION The heat setting should never be higher than 70 degrees when melting White chocolate Overheating White or Milk chocolate causes it to thicken or become clumpy and it will not flow properly To help correct this problem see TROUBLESHOOTING item 2 STARTING THE FOUNTAIN Before Starting The Fountain 1 Ensure that the fountain is on a sturdy LEVEL surface 2 The fountain it self must be level in order to operate and curtain properly Please see FOUNTAIN ASSEMBLY for instructions on leveling the fountain 3 Check to see that fountain basin is securely tightened 4 Ensure that the fountain vent holes and the bottom of the base housing are not covered These areas allow heat to escape from the motor and heating element during use Obstruction of the air flow will cause damage to the motor and internal electrical components 5 Fill the basin with chocolate according
21. simple online ordering of chocolate and accessories Q Can I use Chocolate other than JM Posner Fondue Chocolate in the fountain A Yes other chocolate may be used but it will most likely need to be thinned to the correct consistency to flow through the fountain See instructions under CHOCOLATE PREPARATION Q What are the power requirements for the fountain A JM Posner fountains require a single phase 450W for 501 500W for 502 230V 5Amps power outlet Q Does the JM Posner fountain temper chocolate A No but the chocolate itself can be tempered using standard tempering procedures Q Can fondues other than chocolate run through the fountain A Absolutely Any fondue that is the appropriate consistency can through the fountain This includes caramel cheese and barbecue sauce Use a thinning agent consistent with the fondue s flavor Q What do do if the chocolate is not curtaining completely over the fountain tiers A Please see TROUBLESHOOTING item 1 Q How do store my JM Posner chocolate A Chocolate should be stored in a cool dry place Do not freeze or refrigerate chocolate as condensation may alter the chocolate s consistency 21 FREQUENTLY ASKED QUESTIONS cont Q How much chocolate does the fountain hold A Please see the RECOMMENDED CHOCOLATE AMOUNTS Q The chocolate is purchase in a 2 5Kg bags How may people will that feed A 10 Kg of chocolate will serve around 2
22. the basin with drum To check the fountain is level place a spirit level on the basin rim at various locations Fig 1 If leveling is needed raise or lower a particular side of the fountain by adjusting the feet Step 3 Place metal screw on top of the square center shaft in the middle of basin Fig 2 Step 4 Place the center column on the four pins in the center of the fountain base Fig 3 Step 5 Place the large tier on the center column Fig 5 Step 6 Place the Metal screw extension on top of the metal screw by inserting the male part in to the female part and turning it till the pin drops in the slot Fig 6 Step 7 Place the center column extension on top of the center column and turn it until it sits properly Fig 7 Step 8 Place the 2nd and the 3rd tiers on top of the extension piece Fig 7 Step 9 Place the top hat on top of the extension making sure that the Metal screw pin sits in the middle of the top hat ring To increase the height of the fountain just remove the top hat and insert the extra extension piece and the 4th Tier Replace the top hat on the top of the extension The metal screw should remain the same as before This will not affect the flow of the chocolate Fig 8 Fig 5 Fig 6 FOUNTAIN OPERATING INSTRUCTIONS Step 1 Preheat the fountain by turning on switch on the power socket set the heat level to 70 degrees by pressing the C key Allow fountain to preheat for at
23. the bowl has been removed check the underside and also in the motor compartment for any signs of leaking chocolate this can resemble thick black grease If there is any evidence of this stop using the machine immediately and book a service For the avoidance of doubt any machine that is returned to us where the bearings have seized will be deemed to be out of warranty INTERNATIONAL FIVE YEAR LIMITED WARRANTY Subject to the limitations below JM Posner warrants that the JM Posner Chocolate Fountain you have purchased will be free from defects in materials and workmanship under normal and proper use and service and if properly maintained will perform its intended function for at least a period of five years from the date of purchase If you are not completely satisfied with the quality of the materials or the workmanship of the Fountain you receive you may return it UNUSED within 21 days from the date you received the Fountain and we will provide a replacement Fountain This limited warranty DOES NOT extend to those parts of the Fountain that are subject to wear and tear Components which are generally subject to wear and tear and which are not covered by this warranty may include but are not limited to bearings and seals The motor has a two year warranty This limited warranty applies only to the original purchaser and is not transferable Use other than normal usage is not covered under this warranty The limited warranty provided herein is s
24. to the CHOCOLATE PREPARATION instructions Once The Chocolate Is Melted 1 Place the auger into the cylinder and turn it clockwise to check that it is locked in place over the center spindle Place the crown on the top of the cylinder 2 Press the On switch to START The auger will turn and carry the chocolate up through the cylinder causing it to flow over the Top Hat and Tiers and back into the basin As the cylinder fills with chocolate there may be a brief knocking noise from the auger spinning against the cylinder Adding Additional Chocolate to the Fountain 10 Kg of chocolate will serve approximately 200 people Additional chocolate can be added using the following methods Adding Melted Chocolate add a large amount of chocolate melt it prior to adding it to the basin You can melt it in microwave or in a double boiler Chocolate temperature may be affected by the addition of chocolate or by environmental factors such as operating the fountain in a cold area In such conditions the fountain temperature may need to be adjusted accordingly HELPFUL TIPS 10 Always provide each guest with a plate and skewers Guests should use a separate skewer for each food item Wooden and plastic forked skewers may be ordered online at www jmposner co uk It is also a good idea to have a generous supply of napkins available Guests should never double dip placing a food item that has been bitten back into the fondue flow
25. untain is packaged and shipped in such a way that it arrives to JM Posner or the service center undamaged You are responsible for any damage incurred in shipping We strongly recommend packing your Fountain in your JM Posner Carry Case with inner packing shipping material This warranty is complete and exclusive statement of warranty which JM Posner Ltd agrees to provide with respect to the Fountain and it shall supersede all prior and contemporaneous oral or written agreements understandings proposals and communications pertaining to the subject matter hereof Representations and warranties made by any person including dealers or distributors which are inconsistent or in conflict with the terms of this warranty shall not be binding upon JM Posner unless in writing and approved by an expressly authorized officer of JM Posner IMPORTANT SAFEGUARDS When using our Chocolate Fountain safety precautions should always be followed including the following 1 2 10 11 12 13 14 15 16 17 READ ALL INSTRUCTIONS BEFORE USING THIS FOUNTAIN When the fountain basin is removed the top of the fountain base can be extremely hot AVOID ANY CONTACT WITH THE TOP OF THE FOUNTAIN BASE IF IT IS EXPOSED as the heating element is located directly beneath Avoid all other surfaces that have become hot during use To protect against electrical shock and damage to the fountain do not put the fountain base in water or other liquids Ne
26. utton SAFETY PRECAUTIONS e DO NOT TOUCH HOT SURFACES SOME FOUNTAIN COMPONENTS BECOME HOT DURING USE e WHEN MOVING THE FOUNTAIN MAKE SURE THAT YOU LIFT THE DRUM IF YOU LIFT THE BASIN IT MIGHT COME OFF FROM DRUM NEVER ALLOW LIQUID TO ENTER THE FOUNTAIN BASE THROUGH THE BOTTOM GRATE OR VENT HOLES e ADULT SUPERVISION IS NECESSARY WHEN APPLIANCE IS USED IN PRESENCE OF CHILDREN e AVOID CONTACT WITH ALL MOVING PARTS e ALWAYS UNPLUG THE FOUNTAIN FROM THE ELECTRICAL OUTLET WHEN IT IS NOT IN USE BEFORE PUTTING ON OR TAKING OFF PARTS AND BEFORE CLEANING NEVER COVER VENT HOLES ON THE FOUNTAIN BASIN DOING SO MAY CAUSE THE FOUNTAIN OVERHEAT 14 CHOCOLATE PREPARATION We strongly encourage you to use JM Posner Fondue Chocolate available in Dark Milk and White varieties JM Posner chocolate is specially formulated to melt down to the correct viscosity to flow perfectly through the fountain every time Our unique fondue chocolate is exquisite in taste and aroma and your guests and clients are sure to be delighted Before using the chocolate store it in a cool dry place Do not freeze or refrigerate as moisture could affect the chocolate s consistency You may melt the chocolate directly in the fountain basin in a double boiler or in microwave according to the instructions on the bags WHEN MICROWAVING CHOCOLATE ALWAYS USE HALF POWER TO PREVENT SCORCHING Melting the chocolate directly in the fountain basin takes ap
27. ver allow liquid to enter the fountain base through the bottom grate vent holes or other Openings When basin is removed take extra caution to keep liquid or other objects from entering into the exposed opening at the top of the fountain base Avoid contact with moving parts such as the auger in the cylinder or the spindle in the center of the basin Close supervision is necessary when the fountain is used near children Do not operate the fountain if you observe damage to the electrical cord or plug or if the base of the fountain has been dropped or damaged in any manner The fountain must be returned to JM Posner or a designated repair facility for examination and repair as specified in the Warranty section of this manual Always unplug the fountain from the electrical outlet when it is not in use especially before putting on or taking off parts and before cleaning Do not allow the electrical cord to come into contact with hot surfaces An extension cord may be used if necessary Care should be taken to position the electrical cord so that it does not create a hazard by hanging over a table or counter edge in such a way where it might be tripped on or pulled by those around the fountain Never place any object especially your fingers inside the central cylinder while the fountain is in use Doing so may cause severe injury to persons or damage to the fountain it self The use of accessory attachments other than those made avail
Download Pdf Manuals
Related Search