User manual - Bellman & Symfon
Contents
1. Not reusable Safety and regulations For information on safety and regulations see the Installer s Guide Service and support For information on service and support see the Installer s Guide 24 Installer s Guide 77 79 81 83 84 85 89 91 Introduction Installation Testing Settings Default indication and signals Customizing the signal Trouble shooting Technical information Introduction Function The baby monitor is part of the Visit alerting system that helps people with hearing loss to notice signals in their home When your child cries the baby monitor signals the Visit receiver that notifies you with sound lights or vibra tions depending on the receiver This way you are always close to your baby Activation The baby monitor can be activated by either The test buttons press simultaneously The built in microphone The BE9024 Contact mat accessory connected to the Ext trig input Settings The baby monitor allows you to adjust the sensitivity and delay and you can set a unique signal for each child so you know who needs your attention 77 Overview On Off and settings LED lights Ext trig input Microphone Bellman amp Symfon Turn off Press and hold both buttons for 3 s Switch on Press and hold both buttons for 1 s Contact mat 78 Installing a contact mat By using a cont2. 6 Bellman amp Symfon DESIGN FOR EARS Overview Installation O On Off and settings LEDlights Exttriginput Microphone 1 Remove the battery pull tab to start the baby monitor 2 Place the baby monitor on the nightstand or hang it on the wall with the screw and plug The recommended distance is 0 5 2 m out of reach from the child 6 Bellman amp Symfon Turn off Press and hold both buttons for 3 s Switch on Press and hold both buttons for 1 s Contact mat 19 20 Testing 1 Stand by the child s bed and make a noise 2 The Visit receiver lights up a pacifier symbol and indicates with sound lights or vibrations depending on the receiver If it doesn t react read the section Settings Delay Red LED 30s Settings O The buttons for sensitivity and delay are located on the baby monitor s left side When you press the button the LED shows the current setting Then press repeatedly to adjust the setting fthebaby monitor isn t activated when the baby cries increase the sensitivity If the baby monitor is activated too easily reduce the sensitivity Ifthe baby monitor is activated too fast or too slow adjust the delay G Sensitivity Red LED High Orange LE
3. D Medium Green LED Low Orange LED 10s Green LED 1s 22 Installing a contact mat By using a contact mat you can also be notified if your child gets out of bed Just place the mat in front of the crib connect it to the baby monitor and it will tell you when your child steps on it BE9024 Contact mat sold separately Technical information O Power supply Battery power 2 x 1 5 V AA LR6 lithium or alkaline batteries Power consumption Active lt 70 mA Idle position lt 400 HA Operating time Alkaline 6 months Lithium 1 year Activation Via the test buttons microphone or a contact mat via the ext trig Radio freguency 315 MHz 433 92 MHz or 868 3 MHz depending on region Coverage 50 250 m depending on radio freguency Coverage is reduced by walls large objects and other radio transmitters Number of radio keys 64 as standard Up to 256 with optional software Additional information Please note Always make sure the baby monitor is out of the child s reach Never place the baby monitor in the child s crib or playpen Usage and storage For indoor use only Temperature 15 35 C Rel humidity 5 95 Maintenance and cleaning Maintenance free Clean with a dry cloth Don t use household cleaners aerosol sprays solvents alcohol ammonia or abrasives
4. act mat you can also be notified if your child gets out of bed Just place the mat in front of the crib connect it to the baby monitor and it will tell you when your child steps on it Installation 1 Remove the battery pull tab to start the baby monitor 2 Place the baby monitor on the nightstand or hang it on the wall with the screw and plug The recommended distance is 0 5 2 m out of reach from the child BE9024 Contact mat sold separately 80 79 Testing 1 Stand by the child s bed and make a noise 2 The Visit receiver lights up a pacifier symbol and indicates with sound lights or vibrations depending on the receiver If it doesn t react read the section Advanced testing 18 aa N w 81 Advanced testing Testing the baby monitor is easy First make sure that the baby monitor is installed properly For instructions read the section Installation Using the test button Press both test buttons simultaneously 1 The baby monitor s LED lights up to show that a radio signal is transmitted 2 The receiver s pacifier symbol lights up to show that the signal was received Using the microph
5. and can radiate radio fre quency energy and if not installed and used in accordance with the in structions may cause harmful inter ference to radio communications However there is no guarantee that interference will not occur in a par ticular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is con nected e Consult the dealer or an expe rienced radio TV technician for help For a complete Declaration of Con formity please contact the Bellman amp Symfon European office Industry Canada statement This device complies with Industry Canada Licence exempt RSS 210 Operation is subject to the follow ing two conditions 1 this device may not cause inter ference and 2 this device must European office Bellman amp Symfon Europe AB S dra Langebergsgatan 30 421 32 Vastra Frolunda Sweden Phone 46 31 68 28 20 E mail info bellman com accept any interference including interference that may cause unde sired operation of the device Le fonctionnement de cet quipe ment est soumis aux conditi
6. ay activated too fast For more information read the section Settings The baby monitor is Reduce the delay activated too slow For more information read the section Settings The receiver is activated for no reason e There is probably another Visit system nearby that triggers your system Change the radio key on all units see Changing the radio key Technical information Power supply Power consumption Operating time Activation Radio frequency Coverage Number of radio keys Battery power 2 x 1 5 V AA LR6 lithium or alkaline batteries Active lt 70 mA Idle position lt 400 pA Alkaline 6 months Lithium 1 year Via the test buttons microphone or a contact mat via the ext trig 315 MHz 433 92 MHz or 868 3 MHz depending on region 50 250 m depending on radio frequency Coverage is reduced by walls large objects and other radio transmitters 64 as standard Up to 256 with optional software Additional information Security Usage and storage Maintenance and cleaning Warranty and service 91 Always make sure the baby monitor is out of the child s reach Never place the baby monitor in the child s crib or playpen For indoor use only Temperature 15 35 C Rel humidity 5 95 Maintenance free Clean with a dry cloth Don t use household cleaners aerosol sprays solvents alcohol ammonia or abrasives Not reusable If your baby transmitter appears to be damaged or doesn t functio
7. n properly follow the advice in this booklet and the online resources If it still doesn t function properly contact your retailer for information about obtaining warranty service Hereby Bellman amp Symfon de clares that this Baby monitor is in compliance with the essential requirements and other relevant Use and disposal of batteries Replace only with the same or equi valent type recommended by the manufacturer Please dispose of old defective batteries in an environ provisions of directives R amp TTE 1999 5 EC LVD 1973 23 EC EMC 1989 336 EC MDD 1993 42 EEC FCC compliance statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference re ceived including interference that may cause undesired operation Warning Changes or modifications to this unit not expressly approved by the party responsible for compli ance could void the user s authority to operate the equipment Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to pro vide reasonable protection against harmful interference in a residential installation This equipment gener mentally friendly manner in accordance with the relevant legislation in your country ates uses
8. one Activate the baby monitor by whistling or speaking into the microphone 1 The baby monitor s LED lights up to show that a radio signal is transmitted Ifyou have adjusted the delay it will be postponed as shown on page 83 2 The receiver s pacifier symbol lights up to show that the signal was received Ifyou have customized the signal pattern it will blink as shown on page 85 If it doesn t work as described read the section Troubleshooting 82 Settings The buttons for sensitivity and delay are located on the baby monitor s left side When you press the button the LED shows the current setting Then press repeatedly to adjust the setting Ifthe baby monitor isn t activated when the baby cries increase the sensitivity If the baby monitor is activated too easily reduce the sensitivity Ifthe baby monitor is activated too fast or too slow adjust the delay Sensitivity Red LED High Orange LED Medium GreenLED Low amp Delay Red LED 30 s Orange LED 10s Green LED 1s 83 Default indication and signal Transmitter indication When the baby monitor is activated the LED indicator lights up in green This means that the batteries are in good condition Change batteries if the LEDs blink in orange Only use 1 5 VAA LR6 lithium or alkaline batteries Receiver signal When a receiver is activated it signals with sound flashes or vibrations The default signal pattern is as follows Signal pat
9. ons suivantes 1 l quipement concern ne doit pas causer d interferences et 2 il doit accepter toute interf rence recue y compris les interf rences risquant d engendrer un fonction nement ind sirable Cet appareil num rique de la classe B est con forme a la norme NMB 003 du Canada This Class B digital a paratus com plies with the Canadian ICES 003 Zus tzliche Information Nur Innen verwenden Wartungs frei Reinigung mit einem nur leicht feuchten Tuch HMV 16 99 09 0045 Asia Pacific office Bellman amp Symfon Asia Ltd 1115 16 Main Tower Int l Hotel 339 Huanshi Dong Rd Guangzhou China 510095 Phone 86 20 8318 2950 E mail info cn bellman com 92 DESIGN FOR EARS a 3 3 BE1491 049MAN005
10. r Baby melody 1 x ding dong Lo Baby melody 1 x ding dong 2 x orange blinks 2 x green blinks Orange light Green light iil n o A Baby melody Baby melody 2 x ding dong Lo 2 x ding dong Blinking in orange Blinking in orange Orange light Orange light 1 Baby melody Baby melody Baby melody Baby melody 87 88 Orange light Green light Orange light Green light i Lo ing Hi i Lo 3 x orange blinks 3 x orange blinks Orange light Orange light Trouble shooting Two orange lights appear every 10s A green light appears on the baby monitor but the receiver is not activated The baby monitor is not activated even though the baby is crying 89 Try this e Change the batteries Only use 1 5 V AA LR6 lithium or alkaline batteries e Check the baby monitor s and the receiver s batteries and plugs e Move the receiver closer to the baby monitor e Check that the baby monitor and the receiver are set to the same radio key For more information read the section Changing the radio key e Move the baby monitor closer to the baby or increase the microphones sensitivity see Settings Please note Always make sure the baby monitor is out of the child s reach Never place the baby moni tor in the child s crib or playpen Try this The baby monitor is Reduce the sensitivity or move the baby monitor activated too easily further away from the crib see Settings The baby monitor is Increase the del
11. tern 868 315 MHz O 433 MHz Transmitter Receiver Source uD ED Sound Vibration Flash 1xding dong Lo Baby melody 1 x ding dong Lo Customizing the signal The baby monitor controls the signal pattern on the On receiver By moving a signal switch Y up on you l l can set a unique signal for each baby Note that you Off 1234 need to move the other switches down SIGNAL Signal pattern J 868 315 MHz O 433 MHz Source Switch LED Sound Vibration Flash Baby 1 la Orange light Baby melody Rapid pattern Baby 2 2 x orange blink Baby melody Rapid pattern Baby 3 3 x orange blink Baby melody Rapid pattern Baby 4 k Blinking in orange Baby melody Rapid pattern 85 Changing the radio key o If you install multiple systems you can set a unigue radio key for each system to avoid I E On l l interference Move any radio key switch J Off to the up on position to change radio key 123456 RADIO gt Please note All Visit products within the same system must be set to the same radio key in order to operate as a group All Visit products are set to the same radio key from factory and all radio key switches are positioned down off per default 86 Signal output for 868 MHz and 315 MHz Signal output for 433 MHz Test button 1or 2 Internal Mic Test button 1or 2 Dip switch Output Internal Mic External trigger Dip switch Output External trigger UT rapid panie
Download Pdf Manuals
Related Search