IST IDRIVE 1000 Datasheet
Contents
1. ISS Dimensions 205 x 155 x 70 mm p Weight 1250 grams a a o moe colourcool Patented USA 6 963 175 B2 GB 2369730 Page 2 Drive 1000 the intelligent 210W LED Driver DMX AND PRE SET PROGRAMME SETTINGS e Static Colour 37 preset colours LED Fault Static Colout LED Temp O Cross Fade DMX Error Cyclic Wash e Cyclic Wash 4 preset with 8 speed setting O DMX e DMX address 001 510 with 3 string length setting e Cross Fade 56 preset colours with 8 speed setting C e LED Fault this indicates faulty wiring or connection to the LED fixture Store C P Mode C e LED Temp this will flash when the thermal protection is activated e DMX Error this will flash when the system is set to DMX but no signal is being received WIRING SPECIFICATION INFORMATION DRIVE CONFORMS TO THE FOLLOWING CONNECTION OUTPUT PSU SPECIFICATIONS 8 Pin Terminal Block EMC 1 Channel1 5 Channel 3 EN 55022 55015 2 Channel1 6 Channel 3 EN 61000 6 3 3 Channel 2 7 Thermistor Ground EN 61000 6 4 4 Channel 2 8 Thermistor Temp EN 61547 i f2tstals tells Harmonie amp Flicker aan l EN 61000 3 2 EN 61000 4 2 to EN61000 4 11 IST Ltd recommend that a 10K ohm SMT thermistor Safety type EPCOS B57621C103J62 is located in the centre of the EN 60595 1 amp EN 61558 1 LED board for effective thermal management control Factory Default Setting Stato Colour Cycle Wash Seting No LED fixture2. Yellow The Cross Fade colours for settings 029 056 replicate the above but in pastel colours this means that all colours are on at 50 intensity with the moving colours cross fading between 50 and 100 intensity Plk Black Black Black Black Black Pd p Ped Green Green Green Green Green Fellow Yelow Yellow Fellow Phe Blue Cym colourcool Patented USA 6 963 175 B2 GB 2369730 Page 9 I Drive 1000 the intelligent 210W LED Driver Once the selected cross fade setting has been selected then the speed of the function can be set between 001 008 by using the up down buttons Cross Fade Speeds Time sec s 163 Cyclic Wash 001 004 Number e UEnce e Red Blue Red Green Green Blue clockwise Blue f Red Blue Green Green J Red anti clockwise Setting 003 is as setting 001 but in pastel colour all colours are on at 50 intensity with the moving colours intensity changing between 50 amp 100 Setting 004 is the same as 002 but in pastel setting Once the selected cyclic wash has been selected then the speed of the function can be set between 001 008 by using the up down buttons colourcool Patented USA 6 963 175 B2 GB 2369730 Page 10 Drive 1000 the intelligent 210W LED Driver iDrive 1000 wiring configurations Since the iDrive 1000 power supply is specifically designed for LED applications each channel has its own
3. thermal feedback setting T1 off DMX setting address 001 string length 3 Z AS FLST E The iDrive 1000 has been designed to work with all ER s high powered LED s Future Electronics Patented USA 6 963 175 B2 LUXEON Solution Partner GB 2369730 Page 3 I Drive 1000 the intelligent 210W LED Driver USER MANUAL Set up 1 To re set factory setting switch off at the main s power hold down buttons store and mode then switch on power when the store and mode buttons are released the iDrive 1000 will power up with the pre set function Fig 1 Variable current dimmable LED Driver with thermal protection LED Fault Static Colour LED Temp Cross Fade DMX Error Cyclic Wash Hold To Set Factory Settings Fig 1 2 To change the forward current on each channel the following procedure is used Note please ensure that any changes in the factory set forward current is suitable for the LED type being driven The iDrive 1000 has a changeable forward current range between 350mA and 1000mA in 50mA increments Switch off power supply hold down store and switch power back on as the store and buttons are released the iDrive 1000 will default to the forward current setting for channel 1 and the LED indicator at static colour will be on Fig 2 The current can be changed up amp or down in increments of 50mA and shown on the LED display Once the required forward current has
4. to enable increased longevity for all lighting installations An internal sensor measures the PSU temperature itself to ensure that the system is optimised whatever the environmental conditions whilst a patented closed loop feedback monitoring facility for the LED fixtures can be activated during set up enabling four different temperature profile setting an industry first Both thermal feedback systems will protect LED s and drivers from failure whatever climate they are operating in Patented USA 6 963 175 B2 GB 2369730 colourcool Features e Variable forward current settings on each output channel between 350mA and 1000mA in 50mA increments e Simple LED display interface to control DMX addresses and internal preset functions e Master Slave Option e Universal voltage input with standard IEC converter 100 240V AC 50 60hz e Compact size and rugged aluminium construction e Standard 5 Pin XLR DMX in out connections e Output 8 pin terminal block e Patented Colour Cool thermal management system to optimise and prolong the life of fixtures amp LED s e 4 Thermal control settings to allow for a range of environmental installations e The iDrive technology is licensed and patented in the UK and USA with Worldwide applications pending e Patented colour mixing 3 channel system e Smooth dimming control 0 100 e High Efficiency up to 85 max e Long life and high reliabilty 50 000 hours e Shor
5. 7 I Drive 1000 the intelligent 210W LED Driver iDrive 1000 Static Colour Settings Matrix Mumb 00 10 0 002 100 33 00 ee ee 10 o i0 o 0 n om FP l a PP _ a a e a a a Ed o A A A Lala LA E Lat _ Co _ QQ Coy Coy co E l O cal m ls 114 015 LO LO Oo Oo E AE O E o 00 6 E E 6 JE 02 3 U o o ETE A oi f 100 f 0 U a _ 6 O 5 022 100 100 a4 100 a4 100 SO Ab SA SU 100 AL a IE e o o E o o o y o 30 SA o e E ICI E SO SO s9 AL 031 032 a4 aja SU sp so 50 100 0 83 0 66 30 100 a a m a m 034 100 30 im m5 io 30 100 o 037 100 oy Coy al a al eaa aj al aj Coy Coy co A A lA aay aa Lu Le Le boy boy boy Boy Boy Bo E bo Pm A i Coy coy lO Tr Ll O a 63 La E Le a wo n LA boy Co Go 31 5 La E lo ch Hj A IST Patented USA 6 963 175 B2 GB 2369730 Page 8 colourcool I Drive 1000 the intelligent 210W LED Driver Cross Fade Settings 001 028 are saturated colour 029 056 are pastel colours Cross fade will fade from the start colour in column 1 to the finish colour in column 2 Note Magenta Red amp Blue Cyan Blue amp Green Yellow Red amp Green White Red amp Green White Black Off Number Start Finsh Colour Black Black Black Black Black Black 5 E Yellow Yellow
6. I Drive 1000 the intelligent 210W LED Driver USER MANUAL Product Overview The unique iDrive 1000 LED driver is the latest intelligent innovative driver and control system from IST Ltd designed to optimise the performance of second generation high power LED lighting systems The patented iDrive 1000 includes a wealth of innovative technology to allow the user total choice and flexibility in LED type fixture and installation Each channel can be individually tuned to optimise specific LED forward current settings with a variable constant current output between 350mA and 1000mA precisely in 50mA increments The output connection utilises a simple 8 way terminal block for ease of installation the number of LED s fitted to each channel can be varied The patented power supply automatically adjusts the forward voltage between 14 55 VDC to allow for the number and type of LED s being used since most LED s have different forward voltages The iDrive 1000 will cater for them all it also compensates for voltage drop over long cable runs The iDrive 1000 DMX 512A system has been designed to the latest accreditation and is fully isolated and protected with the ability to use a master slave setup the iDrive 1000 is a truly flexible system designed for the user and lighting designer who requires much more from their lighting systems The iDrive 1000 ensures ultimate reliability with multiple protection systems
7. al safety facility should the temperature inside the casing exceed 65 C the internal thermistor will reduce all output channels by 90 LED fixture thermal feedback derating curves 100 30 au FO 60 Average LED Power 50 TI 40 20 10 0 10 20 30 40 50 60 70 80 90 100 110 120 130 T C Fig 3 LED Fixture Thermal Feedback Derating Curves moe colourcool Patented USA 6 963 175 B2 V 1 4 GB 2369730 Page 6 I Drive 1000 the intelligent 210W LED Driver Master slave Configuration The iDrive 1000 can be used in a master slave arrangement as shown in Fig 4 The first unit in the chain is set to a pre set function such as colour cycle wash or cross fade each subsequent driver is then set to a DMX address 001 Connection is via XLR in and out sockets using appropriate DMX leads This will allow all the units in the chain to replicate the settings and function of the first driver Up to 32 drivers may be connected in the chain The last driver in the chain should be terminated with a 120 ohm metal film resistor as per DMX practice Set colour or function Master Driver cn mm Drive 1000 7 m m i E oe TAL Drive 1000 ey Ew ioe EF Ad mi o Driee 1000 i Drive 1000 G a L et T z a E a E i E a Pa i Slave drivers DMX address set to 001 dr colourcoo 15 A Patented USA 6 963 175 B2 GB 2369730 Page
8. been selected press mode button to select channel 2 the LED indicator at cross fade will be illuminated Again the current setting for channel 2 can be changed up amp or down to the require setting which are shown on the LED display Once the required current settings are obtained press the mode button to go to channel 3 the LED indicator at cyclic wash will be illuminated Repeat the procedure by selecting the required current settings using up amp or down buttons Once all three channels have been set the user can either press store to exit the function and save all settings OR press mode button to gain access to the thermal feedback settings The thermal feedback settings have 4 pre set selections accessed by using up amp or down buttons Lo LST colourcoo Patented USA 6 963 175 B2 V 1 4 GB 2369730 Page 4 I Drive 1000 the intelligent 210W LED Driver OFF no thermal feedback Please note T1 the thermal control will activate between 60 C and 100 C Additional thermal modes T2 the thermal control will activate between 70 C and 110 C have been reserved for T3 the thermal control will activate between 80 C and 120 C future releases T4 the thermal control will activate between 90 C and 130 C Once the required feedback settings have been selected press Store to save and exit the program Please note Any program changes made will be remembered by the iDrive 1000 e
9. ed press store button to save and access the speed control See Cyclic Wash Setting Matrix Page10 colourcoo 15 i Patented USA 6 963 175 B2 GB 2369730 Page 9 I Drive 1000 the intelligent 210W LED Driver Please note when selecting mode settings if the store button is NOT pressed within 20 seconds the iDrive1000 will revert back to its previous stored setting 4 DMX By selecting the DMX button the iDrive 1000 can be controlled by a DMX system full DMX address selection is made using the up or down Y buttons Once the required address has been chosen press the store button This will save the DMX address setting AND allow the user to set the string length between 1 and 3 The string length setting facility is useful in many situations Example If the iDrive1000 is being used to drive all white LED s 12 per channel then by setting the string length to 1 only one fader is required to dim all channels If the string length is set to 3 there is individual control over Red Green amp Blue LED fixture connection 8xpin terminal block connection configuration reading left to right as you look at the header on the PCB is Pin 1 channel 1 Red Pin 2 channel 1 Red Pin 4 channel 2 Green y Pin 5 channel 3 Blue 1 2 3 4 5 8 Pin 6 channel 3 Blue Pin 7 thermister ground Pin 8 thermister LED temperature Internal Thermal Protection The iDrive 1000 contains a built in therm
10. power supply and can be considered separate for the purpose of connecting LED s Consideration as to the mix of LED numbers per channel must be made when using the iDrive 1000 internal stand alone functions Fig 1 shows the iDrive 1000 powering 4 x LED s on the first channel 8 x LED s on the second channel and 12 x LED s on the third channel 8 pin terminal block typical connection using all 8 x wiring options with the thermistor pair included Fig 4 Fig 4 colourcool Patented USA 6 963 175 B2 GB 2369730 Page 11 Drive 1000 the intelligent 210W LED Driver iDrive 1000 wiring configurations As the forward current can be set independently on each output channel the following shows typical but not all possible setup configurations Thermistor if fitted Thermistor if fitted Thermistor if fitted colourcoo Aa LST Patented USA 6 963 175 B2 GB 2369730 If 1000mA If 1000mA If 500mA If 700mA If 500mA If 400mA If 500mA If 350mA If 400mA Page 12
11. t and open circuit protection e Output voltage 14V 55V DC variable e Self test functions e No forward voltage binning resulting in cost savings e Internal thermal protection e Safety approvals include CE Page 1 Drive 1000 the intelligent 210W LED Driver SPECIFICATIONS ELECTRICAL CHARACTERISTICS Input Input Voltage Range 100 240V AC Input Frequency 50 60 Hz Consumption 14 210 Watts Power Factor 70 98 MAX Efficiency 85 MAX Connection Standard IEC Standby Power 14 Watts Total Insulation Class 1 Output Power Output Range 5 55 Watts per channel Output Current 350mA 1000mA per channel Output Current control 50mA increments Voltage 14 55V DC per channel 55V DC Voltage Increment 256 steps Connection 8 Pin terminal Control Input Dimming control DMX 512A Connection Standard 5 Pin XLR Dimming Range 0 100 DMX Start Address Range 1 510 via Display Panel DMX String Length 1 3 via Display Panel Programmes See user manual for all pre sets Master Slave Arrangement See user manual for set up Mechanical Mounting Four 3mm holes for fixing Construction Aluminium casing for improved thermal dissipation Environmental Operating Ambient Temperature 20 C to 40 C Storage Ambient Temperature 20 C to 70 C Case Temperature 65 C Relative Humidity 80 Lifetime failure after 50 000 hours 5 Lifetime failures after 50 000 hours 5 Tr
12. ven if the unit is powered off Variable current dimmable LED Driver with thermal protection LED Fault Static Colour LED Temp DMX Error Hold To Set Forward Current Settings Fig 2 Functions 9 3 Internal functions The iDrive has three internal mode selections for stand alone installations or slave master setup Static colour By pressing the up or down buttons many different colour pre sets can be selected Once the required colour has been selected press store to save and exit See Static Colour Settings Matrix Page 8 Cross fade This effect allows the user to select a cross fade between one colour setting and another example is a fade from Yellow to Purple Many different colour s have been programmed in to the iDrive 1000 to allow a full selection of fades from one colour to another See Cross Fade setting matrix Page 9 The colours are selected by using up amp or down buttons once the required colour s have been selected press the store button to save This action will take the user into a speed selection and the speed between the fade colour s selected can be changed from a fast colour change sp1 to a slow fade sp8 Once the required speed has been selected press store to exit and save Cyclic wash This is a function that will cycle the colours clockwise Red to Green to Blue or anti clockwise Blue to Green to Red Again as with the cross fade once the cycle has been select
Download Pdf Manuals
Related Search