User Manual 802.11AC Dual Band Wireless Router
Contents
1. Enable Disable Auto Loopcomm_2 4GHz Guest Networks 40MHz Upper Y 1 v Enabled Show Active Clients Channel Width Wi Fi operates in two separate channel widths 20Hz and 40Hz 20Hz allows operation on channels 1 11 while 40Hz is 5 11 40Hz allows for faster speeds Select the channel width you wish to use for your network This setting must match that of your Home Network for a successful connection Channel Number Wi Fi networks operate on specific wireless channels Some network channels may have more interference than others If your performance is unstable try a different channel number If you are using a repeater with this network it is recommended you set a static channel instead of using Auto WMM Prioritizes multimedia data over the wireless network Associated Clients Shows the active users connected wirelessly to your network Copyright 2014 Loopcomm Technology Inc All rights reserved Guest Networks 2 4GHz Guest Networks Configure the settings for additional Guest Networks Each Guest Network may have its own specific settings Click Enable to create a Guest Network Guest Networks provide a separate wireless network with unique settings for users to AS Guest Network 2 connect to Guest Network 3 Guest Network 4 Band Restrict the Wi Fi protocol and speed used for the specific Guest Network SSID Th2. Enable IGMP Proxy Internet Group Management Protocol is a communication protocol used by hosts and routers on the network to establish multicast group memberships IGMP Proxy is typically used to implement multicast routing and commonly used when advanced protocols such as PIM is not suitable Enable Ping Access on WAN Allows users to ping the WAN interface IP address from the internet Enable Web Server Access on WAN Remote Management Allows access to the Web Menu over the Internet Enable IPsec pass through on VPN connection Allows the IP security protocol suite to pass through on a VPN connection Enable IPv6 pass through on VPN connection Allows the IPv6 protocol suite to pass through on a VPN connection Copyright 2014 Loopcomm Technology Inc All rights reserved Smart Features The Dual Band Wireless Router provides your network with Smart Features that help to provide convenience and protection for your wired and wireless network The Smart Features allow you to control access of your wireless network through on off schedules specific user authorizations and wireless coverage control These settings apply to your local wireless and wired network Copyright O 2014 Loopcomm Technology Inc All rights reserved Block Websites To block a website you must first enable URL filtering After 1t has been enabled you can begin adding as many websites as you wish into the URL Address field Note If you wish
3. 00 v min 00 v hour 00 min Sunday M 00 v hour 00 v min 00 v hour 00 v min b Select which days you wish for your Wi Fi to be available c Select the time frame during that day that you wish for Wi Fi to be available d Apply Changes Enabling Access Schedule will also disable internet access for wired connections on specified days Note Make sure you have already configured your System Clock in order for your schedule to work correctly Time Zone Settings can be adjusted from the web menu under Management gt Time Zone Settings Copyright O 2014 Loopcomm Technology Inc All rights reserved 2 4GHz WiFi Settings Basic Settings 2 4GHz Disable All Wireless Connections Disabling Wireless will turn off all Wi Fi activity Users will no longer be able to connect wirelessly to your network Band Select the compatible Wi Fi standard and speed for your wireless network Broadcast SSID Selecting Disable Broadcast SSID will hide the visibility of the Dual Band Wireless Router s SSID Users must manually enter the SSID to connect Data Rate Sets the maximum wireless data rate that your network will operate on Wireless Network ID SSID The name of your wireless network Basic Settings 2 4GHz Disable 2 4GHz Wi Fi Connections Band Broadcast SSID Data Rate Wi Fi Network ID SSID Channel Width Control Sideband Channel Number WMM Associated Clients 2 4 GHz B G N v
4. Dynamic Routing If it enabled the Dual Band Wireless Router will automatically build up the routing table according to present link quality connectivity and bandwidth Enable Static Route Subnet Mask Gateway Static Routing If 1t enabled user can set up the fixed routing including IP Metric Interface LAN Show Route Table APPLY ITA LS ROUE Table Netmask Gateway Metric Interface Select address Subnet Mask Gateway for certain use of private network Static Route Table Destination IP Address Delete Selected Delete All Reset Copyright 2014 Loopcomm Technology Inc All rights reserved Management The Management Features on the Dual Band Wireless Router allow you to view the status of the system your Internet connection wireless network and local area network The Network Statistics page provides detailed traffic data for each connection type System Status The System Status provides you with a snapshot of Dual Band Wireless Router current connections and settings System Information This section provides you with information on the version and build time of your firmware This is used to help our support department determine what firmware version your device is running The Current Date Time will display the current clock settings of Dual Band Wireless Router If this time is off go to the System Clock section and configure your system time Internet Connection Status This show
5. Inc All rights reserved Features Complies with IEEE 802 11a b g n and ac Draft 2 0 O Maximum PHY data rate up to 173 3Mbps using 20MHz bandwidth 400Mbps using 40MHz bandwidth 866 7Mbps using 80MHz bandwidth 2x2 MIMO technology for extended reception robustness and exceptional throughput 5MHz 10MHz 20MHz 40MHz 80MHz bandwidth transmission OFDM with BPSK QPSK 16QAM 64QAM and 256QAM modulation Convolutional Coding Rate 1 2 2 3 3 4 and 5 6 Support Network Attached Storage All Giga RJ45 Ports Support USB2 0 Copyright 2014 Loopcomm Technology Inc All rights reserved Technical Specification Wireless Standard 802 11a b g n and ac Draft 2 0 Frequency Band 2 4GHz 5 0GHz Wireless Speed 2 4G Hz 300Mbps Tx Rx 5 0GHz 300Mbps Tx Rx Amplifier Dual 2 4GHz Amplifiers Dual 5 0GHz Amplifiers Dual Low Noise Amplifier Wireless Sensitivity 93dBm Max Wireless Output Power 18dBm Max Wireless Security e WEP WPA WPA2 WPA Mixed WPS User Access Control e MAC address filtering Wireless Access Scheduling e Specific day and time 2 4GHz or 5 0GHz Separately Wireless Coverage Control e 15 100 Output Power 2 4GHz or 5 0GHz Separately Antennas e 2 x Detachable Dual Band 5dBi Omnidirectional Antenna e 2 x Reverse SMA Connector Ports e 1 x RJ 45 10 100 1000M WAN ports Local Ports e 4x RJ 45 10 100 1000M LAN ports Local Ports e USB 2 0 Port for Storage Devices Mounting e Wall Stan
6. Modem Do NOT power on the Modem until prompted at a later step Copyright 2014 Loopcomm Technology Inc All rights reserved Modem f Existing Router Remove Backup battery E qu Modem Connect the Dual Band Wireless Router to your Modem Do NOT connect the power adapter to the Dual Band Wireless Router at this time a Use the included Ethernet cable and connect one end of the cable to your Modem b Connect the other end of the cable to the WAN port on the Dual Band Wireless Router Copyright O 2014 Loopcomm Technology Inc All rights reserved Power on your Modem Plug in your Modem s power adapter and backup battery if available Reinsert Backup battery gt Y Modem Copyright O 2014 Loopcomm Technology Inc All rights reserved Power ON the Dual Band Wireless Router and connect it to your Computer a Attach the antennas of the Dual Band Wireless Router to the antenna ports labeled 1 and 2 b Connect the included grey network cable to an available port on your computer c Attach the power adapter to the Dual Band Wireless Router s PWR port and a power outlet Copyright O 2014 Loopcomm Technology Inc All rights reserved Software Configuration Open your Web Browser to Access the Setup Wizard 1 Open your web browser 2 Type in http setup loopcomm com into the web address bar SN hiteys216 O BEX http setup loopcomm com 3 If
7. Rate Broadcast SSID WMM Access Tx Restrict Mbps Rx Restrict Mbps Active Client List Guest Network 1 Y 5 GHz A N AC Y Loopcomm_5 0_Guest_1 Auto T Enabled Y Enabled Internet and Local 0 0 Show Guest Network 2 5 GHz A N AC v Loopcomm_5 0 Guest_2 Auto v Enabled Enabled Internet and Local v 0 0 Show Guest Network 3 5 GHz A N AC v Loopcomm_5 0_Guest_3 Auto M Enabled Y Enabled Internet and Local v 0 0 Show Guest Network 4 5 GHz A N AC v Loopcomm_5 0 Guest 4 Auto f Enabled v Enabled Internet and Local v 0 0 Show Copyright O 2014 Loopcomm Technology Inc All rights reserved Security 5 0GHz Wireless security allows you to change the type of wireless security settings for your 5 0GHz Network Home Network or Guest Networks Note If you adjust the security of your Home Network and it is Select a Wi Fi Network incorrect the Dual Band Wireless Router will no longer have a Main Loopcomm 5 0GHz Y RESET successful connection to your Home Network Encryption WPA Mixed Y Authentication Mode Enterprise RADIUS Personal Pre Shared Key Using the drop down menu you can select which network you wish to WPA Cipher Selec pes configure and may adjust the security settings below WPA2 Cipher Saite TKIP MW AES Pre Shared Key Format Passphrase M Pre Shared Key ses m If you are using the Guest Network feature you will be able to adjust the security settings for those additional network SS
8. the beacon A beacon is a packet broadcast by the Dual Band Wireless Router to sync the wireless network Preamble Type Defines the length of the Cyclic Redundancy Check for communication between the Dual Band Wireless Router and roaming wireless users TAPP Inter Access Point Protocol Aggregation If it enabled it will combine of several small data frames to enhance the transmission efficiency Short GI If it enabled in 802 11n mode it will bring the advantage of packet anti interference That means the performance will be also greater WLAN Partition If it enabled it will prohibit the communication between clients of LAN STBC Space Time Block Coding improves reception by coding the data stream in blocks 20 40MHz coexist If it enabled it means 20MHz and 40MHz bandwidth will coexist in use Copyright 2014 Loopcomm Technology Inc All rights reserved Wi Fi Protected Setup WPS 2 4GHz WPS is a Wi Fi feature created to make Wi Fi setup simple and hens We Pos Samah ES easy Some wireless routers and adapters support this feature with Enable Wi Fi Protected Setup varying names i e one touch setup or WPS OU re MESIBRO Push Butoncomgurcion bubon her You may enable WPS setup here by selecting the type of WPS Option B Ifyourwireless user asks for the High Power Range Extender setup you wish to use The Dual Band Wireless Router supports all use his number on the user s device 10015315 types of WPS setup Option C If y
9. vew ne ere Senge gt Wireless Senngs gt Scary men wireless Network Security Key wireless 8 Character Minimum Leave blank for no security Click Next to confirm your settings and continue The Router will reboot and apply your settings To change it enter a new key in the Security Key field The key must be 8 characters minimum Click Next to apply your settings The Dual Band Wireless Router will reboot This process may take up to 1 minute The page will automatically reload after the countdown If it does not you may need to refresh the page manually or check your connection to the Dual Band Wireless Router Copyright 2014 Loopcomm Technology Inc All rights reserved Setup Summary Once the Dual Band Wireless Router has rebooted 1t will load the Setup Summary page and provide you with the details of your setup Congratulations your setup is now complete At this time you may disconnect from the High Power Router and start a wireless connection If you have any wired devices that you would like to attach to the High Power Router you may do so now Hi Setup Summary Enjoy your Loopcomm Network Open a new web browser window and check that you have access to the Internet At this time you may disconnect from the Dual Band Wireless Router and start a wireless connection If you have any wired devices that you would like to attach to t A the Dual Band Wireless Router you may do so now as well
10. 100 O 70 O 50 O35 O 15 Copyright O 2014 Loopcomm Technology Inc All rights reserved Access Schedule 2 4GHz Access Schedules will enable or disable your 2 4GHz wireless eee access at a set time based on your predefined schedule Define a schedule for when Wi Fi is enabled or disabled on the High Power Dual Band Range Extender Repeater Please be sure that your time zone settings have been configured before using this feature This feature is often used for restricting access to all users Note When Wi Fi is disabled wired users will no longer have access to the Internet such as children employees guests during specific times of ClEnable Access Schedule 2 4GHz the day for parental control or security reasons E Sunday Vv hour min hour min Sunday Y hour min hour min CEF aa ee lean al fen a Enable Access Schedule Sunday I 00 v houn 00 min 00 y hour 00 min Sunday Y hour min hour min b Select which days you wish for your Wi Fi to Sunday Bs hour M min 2 hour Da mir Sunday Y hour min hour min be available Sunday vo hour min hour min i Sunday Y hour rin hour min c Select the time frame during that day that Sunday M 00 houn 00 rin E our 20 emir Sunday Y hour min hour min you wish for Wi Fi to be available d Apply Changes IS Enabling Access Schedule will also di
11. IDs here as well Copyright O 2014 Loopcomm Technology Inc All rights reserved Advanced Settings 5 0GHz M Advanced Settings 5 0GHz b Advanced wireless settings are for technically advanced users lt is recommended that these settings Advanced Wireless Settings should only be adjusted by technically not be changed unless it is understood what the effects will be on your local wireless network advanced users It is not recommended that novice users adjust these nenat N RTS Threshold 002347 settings to avoid degrading wireless performance Here are a few Beacon interval 100 20 1024 ms sh IAPP O Enabled O Disabled definitions on some settings Protection Enabled Disabled Aggregation Enabled Disabled Short Gl Enabled Disabled WLAN Partition Enabled Disabled Fragment Threshold The Default and Recommended setting 1s at 2346 STEC O Enabled D sabled TX Beamforming Enabled Disabled meaning the Dual Band Wireless Router will never fragment any frames that it sends to wireless users RTS Threshold Adjusts the size of RTS data packets Lower values reduce throughput but allow the system to recover quicker from interference collisions Higher values provide the fastest APPLY throughput Beacon Interval Indicates the frequency interval of the beacon A beacon is a packet broadcast by the Dual Band Wireless Router to sync the wireless network Preamble Type Defines th
12. P Server FTP port Set up the port FTP server will use The default port setting 1s 21 Anonymous FTP Allows any user to login FTP as anonymous Port Range Select a range of ports for the designated IP address that you wish to be forwarded Comment Create a name that you can use to easily identify this Port Forwarding entry E USE storage FTP Server Create a FTP server to access files remotely using a FTP client Insert your USB storage device into the USB port on the back panel of the Router and configure your FTP settings below Use the Internet Address to access the FTP server over the web FTP Connection Internet Address 0 0 0 0 If your Internet connection uses a dynamic IP assignment you may also add a DDNS service to access the FTP via a web address instead FTP Server Setup 7 FP Sener Enabled Disabled FTP Port 21 Anonymous FTP Enabled Disabled Anonymous Write Enabled Disabled System Account List System Account Password Access Type admin admin Read amp Write guest Guest Read Only Note Login and password are case sensitive Copyright 2014 Loopcomm Technology Inc All rights reserved Firewall Settings The Dual Band Wireless Router s Firewall is designed to prevent unauthorized users from accessing your network This section will go over the different features of the Firewall and how to configure them Port Filtering Port Filtering is a security measure that prevents users fr
13. Q Loopcomm User Manual 802 11AC Dual Band Wireless Router Model LP 8096 Copyright 2014 Loopcomm Technology Inc All rights reserved Table of Contents NO De ES A A dic 1 a A EN SE EN 2 A NN 3 TECHHICALS peca a a a a ia da aid 4 Getting SEAT iiO astres RAI AAA AA ATRAE ATA AAA ATREA AAA 5 Packag COS IT AS SR A AA ALTA 5 LED ad as 6 Back Panel Doser ip ei mses sxe da E A AA AS A AS dadas 7 Set p GUIAS si A Ao 8 TAO AM IN 12 SOGHZ IFRS SES att A NOS 20 Bas Sete DO ii tod 20 e A NS 22 Advanced a a a te 23 Wi Er Protected Setup WPS IS 0GHZ nara RI AA 24 Wireless Coverage Cont e e lee all Gao 25 PROCESS O O 26 Copyright O 2014 Loopcomm Technology Inc All rights reserved DAC WAS E A A AAA A N 27 B sic Settings 2 E A O tala A AN Sn Sea er ts 27 D C CAC A ds Add en une idee 29 Advanced Settings 2 ACA a AAA el nue ee ec ped Ps ca id ands Len ee A 30 Wi Et Protected Setup WPS 2 AGH Z ES Aaa 31 Wireless Coverage Controls 2 AGH Z ba 32 Access Schedule 2 A tune ET NO PE 33 IN SE WOT SS CEERI EE Sa secant ud xc A ae icp ace STOLE acess A ae 34 Local N tWork LANJ O ida 34 Internet Network WAN Deorarits nasa NO att 36 ANACO S CLUES A OS 38 Smart Feature Seni ien n a an den ASS IA AAA AAA A IA 39 Ss Es 40 User Access MAC Address Filtering a E A ida 41 User Access iP Address Pit ice 42 MA 5 O 43 Local OS A oia osas 43 A A ss i nr we en nn nr a i NN ae 44 Firewall SUIS A AI A A iS 45 Pott PME SA
14. S sk Sesh an gach NT 45 Copyright 2014 Loopcomm Technology Inc All rights reserved P rt AOS AAA AAA A 46 DMZ Demilitarized LA a tai 47 VIS LAN A A A A ida 48 Ona O ES MIS AA AAA NS a tena 50 ROUTINE SUD oie ae aan rin URETA nd ana N E de NOE a RS ETS RE An EN Ru din dt tatin 51 MA A seras io aca 52 a AA o O N 52 NetWork SUSO A A A A A AS 54 Dynamic DN Simat n a ea a na a tod 55 System COCK arrasar ENET E ENTE TENTA E TENT E EENET ET E NS 56 System LOCS a Ss E E E EE 57 U perade Firmware dr AA A AI AN AA E a A IA 58 Save Relodd Seting S a de nes a re Te SESS 59 PASSWOTA A a dt An ed OR CO TO T CO RO E E TE OE OE 60 Appendix berne O sente sr vesn scan aai ee Dante n etat O 61 D S CARS SDS A e A dt A Pt nt 62 Copyright 2014 Loopcomm Technology Inc All rights reserved Notice e This document is issued to guide users how to install and operate LP 8096 802 11AC Dual Band Wireless Router Please read the document carefully to avoid any damage which is caused by inappropriate use excluding from the warranty e Loopcomm Technology Inc reserves the right to revise update the content of LP 8096 user manual without advance notice Copyright O 2014 Loopcomm Technology Inc All rights reserved Scenario 4 Wireless PC Wireless Printer C ord Internet Wireless Gaming Device eE Smart Phone AA AP Router ADSL MODEM Y C za Tablet PC PC Copyright O 2014 Loopcomm Technology
15. WAN 1 0 VLAN are often used to segment network devices based on appv ES their department user types or common applications Bandwidth can then be more easily managed by adjusting the bandwidth to specific VLANs based on their priorities Copyright 2014 Loopcomm Technology Inc All rights reserved Denial of Service A Denial of Service attack is an attempt by a user or users to make a server s or network s services unavailable The user sends a server multiple requests with false return addresses The server will attempt to respond by sending a request back to the user however since the address is false the server will wait for a response before closing the connection When multiple requests like this occur servers may often get overloaded with too many requests and stop functioning all together This is a typical DoS attack although DoS attacks may not be limited to this type of attack The Dual Band Wireless Router can assist in preventing these types of attacks by scanning the network for patterns of activity that represent DoS attacks Ifa pattern comes in frequently the Dual Band Wireless Router can attempt to block messages containing that pattern and thus protect the server from becoming overloaded and unresponsive Copyright 2014 Loopcomm Technology Inc All rights reserved i Denial of Service The High Power Router can prevent specific DoS attacks from entering your network A Denial of Servic
16. ally redirect common network services to a specific network specific type device or computer on your local network These settings are useful for hosting web servers mail servers network cameras and other specific network server devices behind your network firewall of request comes in on a specific port then that request should be forwarded to a specific device on the private network Enable Port Forwarding IP Address Protocol Both Port Range Comment Port Forwarding is often used for setting up servers cameras and other devices that require remote access RESET Enable Port Forwarding Enables designated ports to begin forwarding IP Address The IP address of the device behind the Firewall that is being designated for Port Forwarding Protocol Select UDP TCP or Both for the protocols to be forwarded Port Range Select a range of ports for the designated IP address that you wish to be forwarded Comment Create a name that you can use to easily identify this Port Forwarding entry Copyright 2014 Loopcomm Technology Inc All rights reserved DMZ Demilitarized Zone A DMZ is a network location or IP Address that is not protected by the firewall When enabling DMZ it is important to note that the device on the IP Address designated as part of the DMZ does not have any protection from the Dual Band Wireless Router s firewall The device s only security would be those built into the operating system As a gen
17. attached to their corresponding antenna connectors D Click Next to continue NEXT Copyright 2014 Loopcomm Technology Inc All rights reserved Configure your Internet Connection Configure your Internet settings using the automatic configuration settings The wizard will check the connection to your modem and attempt to automatically configure your Internet connection settings If there is a problem with the connection the wizard will provide you with information regarding the problem Internet Connection Setup The Smart Setup Wizard will attempt to detect your Internet connection and configure the settings of your Internet connection automatically Automatic Configuration If you wish to configure your Internet connection manually select Manual Configuration Manual Configuration More advanced users may choose to configure their connections manually by selecting Manual Configuration DSL users may require additional login information Select the appropriate connection type and enter the required information Internet Connection gt Automatic Configuration Failed The Smart Setup Wizard cannot find the cable connection to your modem Please check that High Power Router 1 An Ethernet cable is attached to the blue Modem port on the back of the High Power Router and the network port on your modem 2 Your modem is powered on Once you have done so click Automatic Configuration to try again
18. ce will update your new IP address The DDNS web domain that you have chosen to use will then be updated to redirect to your new Internet IP address The DDNS service makes 1t so you never have to check or remember your J Dynamic DNS Settings Enable DDNS Service Provider DynDNS Domain Name host dyndns org User Name Email Password Key DDNS Services TZO Click here to sign up for a TZO DDNS account DynDNS Click here to sign up for a DynDNS account APPLY RESET Internet IP address This feature is typically used for users running servers network cameras and other devices that require remote access Copyright O 2014 Loopcomm Technology Inc All rights reserved System Clock Maintain the internal clock for LP 8096 by syncing with BP system Clock FF SR r computer s time Your system clock settings need t TT COP UIE ti CHE ane EO SE 8s eed to Maintain the system clock settings by syncing the system time with the time on your computer The be accurate in order for logs and wireless access schedules High Power Range Extender Repeater s clock is used to make sure your Access Schedules and logs function correctly and on time to work correctly Current Time Month Day Year Hour Minute Sec Syne with your computer RerResh Copyright 2014 Loopcomm Technology Inc All rights reserved System Logs System Logs are useful for viewing
19. computers on the local network of the Dual Band Wireless Router Insert a USB storage device such as a flash drive or external hard drive to the USB port on the back of the Dual Band Wireless Router and follow the directions below for your operating system The computer must be connected to your Home Network or Network to access the storage device You may also want to Map the Network Drive so 1t shows up as a standard drive on your computer for easier access Hi USB Storage Local Sharing Share a USB storage device such as a USB flash drive or external hard drive locally among networked computers Insert your USB storage device into the USB port on the back panel of the Router Check the Elite Support Center for new USB Storage features Local Network Sharing USB Drive Not Connected REFRESH Partition File System Capacity Free Space How to Access or Map your Network Drive Note You may need to Map your Network Drive for itto appear in your computer s networked device list USB Device Name LOOPCOMM_USB Work Group WORKGROUP Shared Disk IP Address 192 168 3 1 For Mapping the Network Drive Copyright O 2014 Loopcomm Technology Inc All rights reserved FTP Server Create a FTP server to access files remotely using a FTP client Insert your USB storage device into the USB port on the back panel of the Dual Band Wireless Router and configure your FTP settings below FTP Server Enable or Disable FT
20. d or Desktop Setup Requirements e Wired or wireless PC Mac and an available 802 11a b g n or ac Draft2 0 wireless network e Google Chrome Internet Explorer 8 0 and up or Safari Web browser Copyright O 2014 Loopcomm Technology Inc All rights reserved Getting Started Package Contents Check to make sure you have all the contents within your package 802 11ac Dual Band Wireless Router Two Detachable 5dBi Omnidirectional Antennas Power Adapter AC 100 240V DC 5V 2A Two RJ 45 Ethernet Cable Quick Installation Guide Product CD Stand for Vertical Mounting Copyright 2014 Loopcomm Technology Inc All rights reserved LED Indicators Power Indicates when the Dual Band Wireless Router is powered on The LED will remain on 5 0GHz Wireless Activity Blinks rapidly when wireless data traffic is transmitted or received over the 5 0GHz wireless network 2 4GHz Wireless Activity Blinks rapidly when wireless data traffic is transmitted or received over the2 4GHz wireless network WPS Wi Fi Protected Setup activity When the WPS mode is activated the WPS LED blinks as 1t awaits a connection USB Connection Indicates when a USB storage device is connected to the USB port for local sharing Gigabit Wired Ports 1 4 Indicates when a networking device is connected to a wired port on the back of the Dual Band Wireless Router The LED blinks rapidly when wired data traffic is transmitted or received Int
21. e DoS attack is characterized by an explicit attempt by malicious users to prevent legitimate users from use of a specific internet service To activate your protection enable the DoS Prevention below and configure the specific settings Enable Denial of Service DoS Prevention Whole System Flood SYN Packet Second Whole System Flood FIN 0 Packet Second Whole System Flood UDP 0 Packet Second Whole System Flood ICMP 0 Packet Second Per Source IP Flood SYN 0 Packet Second Per Source IP Flood FIN 0 Packet Second Per Source IP Flood UDP 0 Packet Second Per Source IP Flood ICMP 0 Packet Second TCP UDP PortScan Low Sensitivity ICMP Smurf IP Land IP Spoof IP TearDrop PingofDeath TCP Scan TCP SynWithData UDP Bomb UDP EchoChargen SelectAll ClearAl Enable Source IP Blocking 0 Block Time sec Quality of Service QoS prioritizes and guarantees network performance for a specific IP Address range or MAC Address QoS is often used for applications that require steady bandwidth Common applications include VoIP phones video streaming applications 1 e DVRs network cameras video on demand online gaming and servers It is important to note that while QoS helps to prioritize and guarantee bandwidth for a specific device it does not provide you with more bandwidth than you currently have For example if your Internet Provider rates your internet connection speed at 5Mbps QoS will not im
22. e length of the Cyclic Redundancy Check for communication between the Dual Band Wireless Router and roaming wireless users TAPP Inter Access Point Protocol Aggregation If it enabled it will combine of several small data frames to enhance the transmission efficiency Short GI If it enabled in 802 11n mode it will bring the advantage of packet anti interference That means the performance will be also greater WLAN Partition If it enabled it will prohibit the communication between clients of LAN Copyright 2014 Loopcomm Technology Inc All rights reserved STBC Space Time Block Coding improves reception by coding the data stream in blocks TX Beamforming It s a technique implemented in digital signal processing DSP logic to improve range and data rate Wi Fi Protected Setup WPS 5 0GHz M Wi Fi Protected Setup 5 0GHz WPS provides hassle free setup for wireless users connecting to the High Power Dual Band Range Extender Repeater Use one of the following WPS processes to configure WPS WPS is a Wi Fi feature created to make W1 Fi setup simple and easy Some wireless routers and adapters support this feature with AA ee varying names 1 e one touch setup or WPS ay st 3 i DEC g You may enable WPS setup here by selecting the type of WPS setup l Internet Router you wish to use The Dual Band Wireless Router supports all types of O Disable Wi Fi Protected Setup WPS WPS setup Enable Wi Fi Protec
23. ecided by the DHCP lease time After the Lease Time expires the DHCP server will assign another IP address to the device Set Static DHCP This allows specific devices to be given a specific IP address each time the device connects to the network The DHCP server will always assign the same IP address to the same device This feature is often used for shared devices such as network printers or servers Copyright 2014 Loopcomm Technology Inc All rights reserved 802 1d Spanning Type STP A network protocol that ensures a loop free topology for networks that have Ethernet bridges The STP prevents bridge loops and allows a network design to include redundant links to provide automatic backup paths if active links fails Clone MAC Address The Dual Band Wireless Router can use a MAC address that you define as its own This is often used when an Internet Provider only authorizes one MAC address to access the Internet Cloning the MAC address will make it so that the cloned MAC address is the only MAC address seen by the Internet Provider Copyright 2014 Loopcomm Technology Inc All rights reserved Internet Network WAN Internet Protocol Version Pv4 Internet Connection Type Automatic Dynamic IP DHCP The Smart Setup Wizard will assist you in setting up your Internet connection Host Name Loopeomm MTU Size 1492 1400 1492 bytes However in the case that you wish to adjust settings manually the options on
24. ed wirelessly to your network Basic Settings 5GHz Disable 5 0GHz Wi Fi Connections Band Broadcast SSID Data Rate Wi Fi Network ID SSID Channel Width Control Sideband Auto Channel Number WMM Associated Clients 5 GHz A N AC Enable Disable Auto v Loopcomm_5 0GHz Guest Networks 80MHz v 44 v Enabled Show Active Clients Copyright 2014 Loopcomm Technology Inc All rights reserved Guest Networks 5 0GHz Click Enable to create a Guest Network Guest Networks provide a separate wireless network with unique settings for users to connect to Band Restrict the Wi Fi protocol and speed used for the specific Guest Network SSID This is the name of your Guest Network Data Rate Restrict access to the Guest Network by setting a lower bandwidth by changing the data rate Broadcast SSID Disable to hide your SSID from public view Users will need to manually enter the SSID into their wireless software interface to connect Access Restrict access for Guest networks to allow Internet only connections and protect your local network Associated Clients View all computers and network devices that are connected to your Guest Network wirelessly To set security settings for the Guest Network go to 5 0GHz Wi Fi Settings gt Security Guest Networks Configure the settings for additional Guest Networks Each Guest Network may have its own specific settings No Enable Band SSID Data
25. eral safety rule devices placed on the DMZ should not have any other network connections to any other devices Enable DMZ Enables the Demilitarized Zone Bf Demilitarized Zone DMZ A Demilitarized Zone is used to provide unrestricted access for a single IP address on your network The DMZ enabled IP address will have an unrestricted path directly through the firewall of the High Power Router C Enable DMZ DMZ Host IP Address APPLY _ RESET DMZ Host IP Address The designated IP Address of the network device to have unrestricted access through the Dual Band Wireless Router s Firewall Copyright 2014 Loopcomm Technology Inc All rights reserved Virtual LAN A VLAN has the same attributes as a physical local area network LAN M Virtual Local Area Network VLAN but it allows for devices to be grouped together even if they are not located pr Poma ri rt tre a network by department user type or primary application on the same physical network switch The benefit of a VLAN is that it allows Ste network traffic to flow more efficiently for computers or network devices cg re a on ace A a Wired Port1 LAN 3022 0 that are within sections of mutual interest In addition changes to the VLAN nue er ae z Wired Port4 LAN 1 3 can be made virtually via a user interface rather than manually changing oe lo b Guest SSID1 LAN 1 0 Guest SSID2 LAN 1 0 cables and network switches Guest SSIDA LAN 0 Guest SSID4 LAN 1 0 Modem Port
26. ernet Connection Indicates when the Dual Band Wireless Router is connected to a broadband modem The LED will blink when Internet traffic 1s transmitted or received Copyright O 2014 Loopcomm Technology Inc All rights reserved Back Panel Description Antenna Connectors 1 2 SMA antenna connectors Attach the included high gain dual band antennas to these connectors WPS Hold down for 3 seconds to enable WPS push button configuration Reset Push down once to reboot the Dual Band Wireless Router Hold down for 5 10 seconds to reset the Dual Band Wireless Router back to factory settings Power Power adapter port AC Input 100 240V DC Output 5V 2A USB Port Attach USB storage devices such as USB flash drives and external hard drives for file sharing Wired Devices Gigabit RJ 45 ports for connecting to wired computers or network devices Modem RJ 45 port for connecting to your Broadband Modem Copyright 2014 Loopcomm Technology Inc All rights reserved Setup Guide Setup Preparations 1 Disconnect and Power Off your Existing Wireless Router 2 Disconnect your existing Wireless Router from your computer your broadband modem and its power outlet If you do not have an existing Wireless Router please continue to the next step Power off your Modem Please Power off the Modem by disconnecting the Modem s power adapter from the power outlet If your Modem has a backup battery remove the backup battery from your
27. he output power and range of your Extended Wireless Network For a smaller coverage area choose a lower output power percentage For a larger coverage area select a higher output power percentage po Wireless Output Power 100 O7o O50 O35 O 15 Copyright O 2014 Loopcomm Technology Inc All rights reserved Access Schedule 5 0GHz Bi Access Schedule 5 0GHz Access Schedules will enable or disable your 5 0GHz Define a schedule for when the 5 0GHz Wi Fi network is enabled or disabled on the Router Please be wireless access at a Set time based on your predefined sure that your time zone settings have been configured before using this feature schedule This feature is often used for restricting Enable Access Schedule 5 0GHz A Enable Day From To access to all users such as children employees e 00 aia 00 v a 00 v MEE oo y MERA Sunday v 00 hour 00 v min 00 v hour 00 min guests during specific times of the day for parental Sunday v 00 hour 00 v min 00 hour 00 min Sunday M 00 hour 00 v min 00 v hour 00 v min control or security reasons Sunday Y 00 v hour 00 min 00 v hour 00 v min Sunday M 00 hour 00 min 00 v hour 00 min Sunday M 00 hour 00 v min 00 v hour 00 v min Sunday v 00 hour 00 v min 00 hour 00 min a Enable Access Schedule Sunday v 00 hour
28. hnology Inc All rights reserved Appendix Copyright O 2014 Loopcomm Technology Inc All rights reserved Default Settings The default settings for your Dual Band Wireless Router are listed here If for some reason you need to return LP 8096 back to default settings hold down the Reset button on the back panel for 10 seconds LP 8096 will reset back to factory settings as listed below IP Address 192 168 3 1 Web Menu Access http setup loopcomm com WLAN 2 4GHz SSID Loopcomm_2 4G Hz Wireless Security Key WPA WPA2 Mixed Mode loopcommwifi WLAN 5 0GHz SSID Loopcomm_5 0GHz Wireless Security Key WPA WPA2 Mixed Mode loopcommwifi Copyright 2014 Loopcomm Technology Inc All rights reserved
29. ia A DNS 1 0 0 0 0 this page provide you with the tools to do this easily DNS 2 DNS 3 Optional If required by your Internet provider Clone MAC Address 000000000000 Clone MAC Address Select your Internet Connection type from the drop down menu Manual IP Static For Internet connections where the Internet provider does not provide you with an IP address automatically If you know the IP address and DNS settings that your Internet provider uses select this option Automatic Dynamic DHCP This is the configuration type most often used by Internet providers Automatic configurations are used by both DSL and Cable as well as other providers Under the Automatic Configuration method the Internet provider will assign your Dual Band Wireless Router an Internet IP address automatically Note If for some reason you do not get an IP address and you know that your Internet provider uses DHCP try resetting your Modem Remove the power adapter from the Modem as well as the backup battery if available Wait about 30 seconds and then power the Modem back on You can run through the Smart Setup Wizard again to see if that fixes your Internet connection issues Copyright 2014 Loopcomm Technology Inc All rights reserved PPPoE connections normally require login information If you do not know the settings for your PPPoE connection please contact your Internet provider PPTP and L2TP connections require login info
30. is is the name of your Guest Network Data Rate Restrict access to the Guest Network by setting a lower bandwidth by changing the data rate Broadcast SSID Disable to hide your SSID from public view Users will need to manually enter the SSID into their wireless software interface to connect Access Restrict access for Guest networks to allow Internet only connections and protect your local network Associated Clients View all computers and network devices that are connected to your Guest Network wirelessly To set security settings for the Guest Network go to 2 4GHz Wi Fi Settings gt Security Copyright 2014 Loopcomm Technology Inc All rights reserved Security 2 4GHz Wireless security allows you to change the type of wireless security settings for your 2 4GHz Network Home Network or Guest Networks Note If you adjust the security of your Home Network and it is incorrect the Dual Band Wireless Router will no longer have a successful connection to your Home Network Using the drop down menu you can select which network you wish to configure and may adjust the security settings below If you are using the Guest Network feature you will be able to adjust the security settings for those additional network SSIDs here as well Configure the Security Settings for your 2 4GHz Wi Fi network 2 4GHz Wi Fi Network WS a Ws JL We Internet Modem Select a Wi Fi Network Main Loopcomm_2 4GHz Encry
31. n blocking access enable MAC Filtering and enter the MAC address below without spaces or symbols i e A1B2C3D4E5F6 Enable MAC Filtering Current Mode Deny Listed Select from Client List Change Mode Deny Listed MAC Address Comment For Windows computers with internal networking adapters the MAC Address can be found by viewing the Network Connection Details of the network adapter The MAC Address will be listed as the Physical Address Be sure to enter the MAC Address without any symbols For example a MAC Address of 78 DD 78 AA 78 BB would be entered as 78DD78AA78BB Copyright 2014 Loopcomm Technology Inc All rights reserved User Access IP Address Filtering User Access IP Filtering is similar to User Access MAC filtering except that the Dual Band Wireless Router uses the local IP address to filter the specific data from the specified network protocol For example if you chose to block TCP data packets from a specific computer you would need to figure out what that device s IP address is and select TCP from the Protocol drop down menu If you are not sure which Protocol to filter select Both as your Protocol selection Enable IP Filtering Select IP Type IPv4 Address IPv6 Address Select from Client List Comment Protocol Bott Pv4 standard IPv6 Copyright 2014 Loopcomm Technology Inc All rights reserved USB Storage Local Sharing Share a USB storage device with
32. o Internet Modem High Power Router Enjoy your Loopcomm Wireless network Copyright O 2014 Loopcomm Technology Inc All rights reserved 5 0GHz WiFi Settings Basic Settings 5 0GHz Disable All Wireless Connections Disabling Wireless will turn off all Wi Fi activity Users will no longer be able to connect wirelessly to your network Band Select the compatible Wi Fi standard and speed for your wireless network Broadcast SSID Selecting Disable Broadcast SSID will hide the visibility of the Dual Band Wireless Router s SSID Users must manually enter the SSID to connect Data Rate Sets the maximum wireless data rate that your network will operate on Wireless Network ID SSID The name of your wireless network Channel Width Wi Fi operates in two separate channel widths 20Hz and 40Hz 20Hz allows operation on channels 1 11 while 40Hz is 5 11 40Hz allows for faster speeds Select the channel width you wish to use for your network This setting must match that of your Home Network for a successful connection Channel Number Wi Fi networks operate on specific wireless channels Some network channels may have more interference than others If your performance is unstable try a different channel number If you are using a repeater with this network it is recommended you set a static channel instead of using Auto WMM Prioritizes multimedia data over the wireless network Associated Clients Shows the active users connect
33. om using specific ports ie eugene o titering for reasons other than what those ports were originally intended for For example Port Filtering allows you to enable or disable TCP ports and UDP ports on computers or network devices Port Filtering insulates your local computers from many TCP IP security attacks including internal TCP port 21 is traditionally used for FTP However there is nothing stopping a attacks by malicious users user from using port 21 for purposes other than FTP access By enabling Port Enable Port Filtering Select IP Type IPw4 Standard IPv6 Filtering on TCP port 21 only FTP communications would be allowed No other Port Range Protocol Both v types of communication would be allowed on this port Comment Hackers may sometimes scan for all open ports on your network as a method of hacking into your network Port Filtering and other firewall features help to prevent this from happening To set up Port Filtering select a range of ports you wish to filter If you are trying to filter a single port enter the port number twice For example Port 21 21 21 Select the Protocol of the port you are filtering If you do not know what protocol you wish to filter select Both Copyright O 2014 Loopcomm Technology Inc All rights reserved Port Forwarding Port Forwarding is a rule that tells the Dual Band Wireless Router that if a IM Port Forwarding z Port Forwarding allows you to automatic
34. or select Manual Configuration to manually set your Internet connection settings Automatic Configuration Manual Configuration Copyright 2014 Loopcomm Technology Inc All rights reserved Ifthe Automatic configuration was successful you will be directed to a E internet Connection gt Automatic Configuration Successful Configuration Successful page The Smart Setup Wizard has successfully configured your Internet connection Click Next to continue Internet Modem High Power Router Please press Next to continue Copyright O 2014 Loopcomm Technology Inc All rights reserved Set the System Clock i System Clock The System Clock is used for system logs and setting schedules for Internet access Update the System Clock for the High Power Router by clicking the Sync button below Click Sync to synchronize the System Clock with the time on your computer Current Time 4 Month 2 Day 2013 Year 14 Hour 54 Minute 25 Sec Click Next to continue Sync with your computer Sync Click Next to confirm your settings and continue BACK NEXT Copyright 2014 Loopcomm Technology Inc All rights reserved Configure your Wireless Settings The default SSID of the Dual Band Wireless Router is Loopcomm_5 0G Hz D Wireless Settings 5 0GHz Network To change it enter a new name in the SSID field Users connecting wirelessly to the Dual Band Wireless Router will use this ID to identify your wirele
35. our wireless user has a Wi Fi Protected Setup PIN number enter that number here sand then click Option A Push button You may push the WPS button on the web menu or use the physical button on the back of the Dual Band Wireless Router Option B PIN Some wireless devices use a PIN number to access wireless network If your wireless device requests for a PIN number then use the PIN code located here Option C Enter PIN Some wireless devices require that you use a PIN number to add them to the wireless network If your wireless device has a PIN number then locate the number and enter in the field then press Start Pin Copyright 2014 Loopcomm Technology Inc All rights reserved Wireless Coverage Controls 2 4GHz Adjust the output power of the Dual Band Wireless Router to control the coverage distance of your 2 4GHz Wireless Network For a smaller coverage area you can select a lower output power For the maximum wireless coverage select the 100 selection Note that if you select a lower output power your connection to your 2 4GHz Home Network will also decrease in range It is recommended that you test your signal strength after each adjustment BM Wireless Coverage Controls 2 4GHz Adjust the output power and range of your Extended Wireless Network For a smaller coverage area choose a lower output power percentage For a larger coverage area select a higher output power percentage Wireless Output Power
36. prove that connection QoS helps you better manage the 5Mbps that you have so that the bandwidth is prioritized for devices on your network that may need the provided 5Mbps more than other devices However if you have an application that requires more than 5Mbps of steady bandwidth the application will continue to experience lag with or without QoS since your available bandwidth is less than the required bandwidth of your application i Quality of Service Bandwidth Management Quality of Service QoS enables the prioritizing of specific data traffic through your network With Quality of Service you can guarantee that a specific computer or network device has sufficient user defined bandwidth and is prioritized over all other network traffic Enable Quality of Service Automatic Uplink Speed Manual Uplink Speed Kbps 512 Automatic Downlink Speed Manual Downlink Speed Kbps 512 Quality of Service Rules Address Type IP Address MAC Address Local IP Address MAC Address Mode Guaranteed minimum bandwidth Uplink Bandwidth Kbps Downlink Bandwidth Kbps Comment APPLY RESET Copyright 2014 Loopcomm Technology Inc All rights reserved Routing Setup E Routing Setup Setup Dynamic or Static Routing protocols for advanced users only Users can set up dynamic or static routing protocols on this page Enable Dynamic Route NAT Enable Disable Transmit Disabled RIP 1 RIP 2 Receive Disabled RIP 1 RIP 2
37. ption WPA Mixed Authentication Mode Enterprise RADIUS Personal Pre Shared Key WPA Cipher Suite TKIP Y AES WPA2 Cipher Suite TKIP Y AES Pre Shared Key Format Passphrase v Pre Shared Key Copyright O 2014 Loopcomm Technology Inc All rights reserved IM Advanced Settings 2 4GHz A d d S tti 2 A 1 I These settings apply to your 2 4GHz Wi Fi network Advanced Wi Fi settings are for technically Vance etungs Z advanced users It is recommended that these settings not be changed unless it is understood what the effects will be on your local Wi Fi network Advanced Wireless Settings should only be adjusted by technically Fragment Threshold 2346 256 2346 advanced users It is not recommended that novice users adjust these o ee settings to avoid degrading wireless performance Here are a few Preamble Type Long Preamble Short Preamble definitions on some settings e ss ke Aggregation Enabled Disabled Fragment Threshold The Default and Recommended setting is at 2346 vm Sa ee 2 meaning the Dual Band Wireless Router will never fragment any frames STEC Enabled Disabled that it sends to wireless users 20 40MHz at ia ie RTS Threshold Adjusts the size of RTS data packets Lower values reduce throughput but allow the system to recover quicker from interference collisions Higher values provide the fastest throughput Beacon Interval Indicates the frequency interval of
38. rmation as well as IP address settings If you do not know the settings for your PPTP L2TP connection please contact your Internet provider Copyright O 2014 Loopcomm Technology Inc All rights reserved Advanced Settings These settings apply to the Local Network and your Internet Connection E Advanced Settings Network If you are not familiar with these settings please refer to a These settings apply to the Local Network and your Internet Connection Network If you are not familiar with these settings please refer to a network administrator to avoid putting your network at risk network administrator to avoid putting your network at risk Enable uPNP Universal Plug and Play Enable uPnP Universal Plug and Play is a network feature that allows Enable IGMP Proxy gt i Enable Ping Access on WAN uPnP enabled devices to just work with each other when connected to Eadie Web Saa Net an WAN Giroko Shi 5 Y Enable sec pass throu on connection the same network UPnP can work across different network media such A A Enable PPTP pass through on VPN connection as an Ethernet connection or wireless connection With UPnP enabled 2 Enable L2TP pass through on VPN connection network devices may change security settings within the Dual Band IPv6 Advanced Settings z Enable IPv6 Tunnel 6to4 Wireless Router s firewall to allow access over the Internet By default AA UPnP is disabled to avoid exposing your network to security issues
39. s Network These statistics shows all data activity for all users connected wirelessly to Dual Band Wireless Router Wired Connection The Wired Connection statistics shows all data activity for all users physically connected to the wired ports on the Dual Band Wireless Router Internet Connection The Wired Connection statistics shows all data activity for all users connected to Internet Bi Network Statistics 5 0GHz Wireless Connection 2 4GHz Wireless Connection Wired Connection Internet Connection Sent Packets Received Packets Sent Packets Received Packets Sent Packets Received Packets Sent Packets Received Packets 152 9719 9473 215902 22398 21599 Copyright 2014 Loopcomm Technology Inc All rights reserved Dynamic DNS Settings The Dynamic Domain Name System DDNS is a method to keep a Web domain name or Web address linked to a changing IP address as most Internet Providers do not provide static IP addresses To use DDNS you must first set up an account with a DDNS provider The Dual Band Wireless Router supports two of these providers TZO and DynDNS Once the DDNS service has been set up and configured correctly on the Dual Band Wireless Router the DDNS service will constantly track the IP address of your Internet connection Each time your Internet Provider changes your IP address the Dual Band Wireless Router will inform the DDNS service and the DDNS servi
40. s the Internet connection type and related settings Copyright O 2014 Loopcomm Technology Inc All rights reserved i System Status System Information Uptime Firmware Version Build Time Current Date Time Internet Connection Status Internet Connection Type IP Address Subnet Mask Default Gateway DNS Server MAC Address Oday 1h 8m 37s v3 4 6_L01 Wed Feb 19 14 12 39 CST 2014 2 19 2014 15 20 55 Not Connected 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 00 e0 4c 81 96 c9 I 5 0GHz Wi Fi Network Settings Channel Number Encryption BSSID Associated Clients 5 GHz A N AC Loopcomm_5 0GHz 44 WPA2 Mixed 00 e0 4c 81 96 c1 0 5 0GHz 2 4GHz Wi Fi Network Settings It includes present band mode SSID operating channel number IE 2 4GHz Wi Fi Network Settings security and linked clients Band 2 4 GHz B G N SSID Loopcomm_2 4GHz Ch Number 11 Local Area Network Settings o Encryption WPA2 Mixed It indicates LP 8096 s IP address Subnet Mask Default Gateway DHCP server AA enabled disable and MAC address Associated Clients 0 Local Area Network Settings O Router IP Address 19216831 Subnet Mask 255 255 255 0 Default Gateway 192 168 3 1 DHCP Server Enabled MAC Address 00 e0 4c 81 96 c1 Copyright O 2014 Loopcomm Technology Inc All rights reserved Network Statistics These statistics show the data activity for each network connection 5 0GHz 2 4GHz Wireles
41. sable internet access for wired connections on specified days Note Make sure you have already configured your System Clock in order for your schedule to work correctly Time Zone Settings can be adjusted from the web menu under Management gt Time Zone Settings Copyright O 2014 Loopcomm Technology Inc All rights reserved Network Settings Local Network LAN These settings are for your local network only and do not apply to your Internet ISP connection IP Address The IP address of the Dual Band Wireless Router Subnet Mask The subnet of the Dual Band Wireless Router Default Gateway The access point to another network IP Address Subnet Mask Default Gateway DHCP DHCP Client Range DHCP Lease Time Static DHCP Domain Name 802 1d Spanning Type 192 168 3 1 256 255 255 0 0000 Sever Y 1921683100 192 168 3 200 480 1 10080 minutes loopcomm Disabled DHCP Each network device on your local network will have its own IP Address The DHCP server automatically assigns the IP addresses to each device connected to your network Disabling DHCP will require that each device on your network be assigned a manual or static IP address DHCP Client Range The range of IP addresses provided by the DHCP server is defined by this field You can limit how many IP addresses are used in your network by setting a smaller or larger range DHCP Lease Time The amount of time each device is given a specific IP is d
42. ss network The default Security Key WPA WPA2 for your wireless network is wireless To change it enter a new key in the Security Key field The key must be Wi Fi Network ID SSID Loopcomm_5 0GHz 8 characters minimum Security Settings Your 5 0GHz Wi Fi network is secured with the following WPA WPA2 security password key You must enter this key when connecting wirelessly for the first time to the Router You may change the key below Click Next to continue Note To specify ti ther type of encryption please view the More Settings gt Wireless Settings gt Security menu for more security optio our setup is complete Network Security Key wireless 8 Character Minimum Leave blank for no security Click Next to confirm your settings and continue Copyright O 2014 Loopcomm Technology Inc All rights reserved The default SSID of the Dual Band Wireless Router is Loopcomm_2 4GHz To change it enter a new name in the SSID field Users connecting wirelessly to Wi Fi Network ID SSID Loopcomm_2 4GHz the Dual Band Wireless Router will use this ID to identify your wireless network Security Settings Your 2 4GHz Wi Fi network is secured with the following WPA WPA2 security password key You must enter this key when connecting wirelessly for the first time to the Router You may change the key below The default Security Key WPA WPA2 for your wireless network is he To pee use taner ype tenon lease
43. ted Setup Option 4 If your wireless user has a Wi Fi Protected Setup button click or press the WPS PBC Push Button Configuration button here Option A Push button You may push the WPS button on the web menu or use the physical button on the back of the Dual Band A heii a use this number on the user s device 10015315 Wireless Router Option C If your wireless user has a Wi Fi Protected Setup PIN number enter that number here Py A md then click Lem Option B PIN Some wireless devices use a PIN number to access wireless network If your wireless device requests for a PIN number then use the PIN code located here Option C Enter PIN Some wireless devices require that you use a PIN number to add them to the wireless network Copyright 2014 Loopcomm Technology Inc All rights reserved If your wireless device has a PIN number then locate the number and enter in the field then press Start Pin Wireless Coverage Controls 5 0GHz Adjust the output power of the Dual Band Wireless Router to control the coverage distance of your 5 0GHz Wireless Network For a smaller coverage area you can select a lower output power For the maximum wireless coverage select the 100 selection Note that if you select a lower output power your connection to your 5 0GHz Home Network will also decrease in range It is recommended that you test your signal strength after each adjustment M Wireless Coverage Controls 5 0GHz Adjust t
44. the activity and history of the Dual Band Wireless Router The System Logs are also used to help M System Logs troubleshoot when needed View network and system activity for your Router Enable Log A Current Time System ALL Wireless DoS It is recommended that you enable all logs in the event that Enable Remote Log Log Server IP Address troubleshooting is required All log entries are deleted each time the Dual Band Wireless Router reboots or is powered off Copyright 2014 Loopcomm Technology Inc All rights reserved Upgrade Firmware Loopcomm continuously updates the firmware for all products in an effort to constantly improve our products and their user eras experiences The Router uses software firmware to operate In the event that a new firmware file is available you may update it here During the upgrade process DO NOT power off the device to avoid damage to the Router Check the Loopcomm Website for your product frequently to Current Firmware Version v3 4 6_L02 see if there are any updates Build Time Thu Mar 13 09 53 32 CST 2014 Select File Browse The firmware update is downloaded as a zip file from the Support Web page You will need to have an unzipping program to open the file Upload Reset To manually upgrade your firmware a Download the file from Loopcomm Website and remember the location where you saved it b Click Choose File and locate the file c Click Upload to begin
45. the web menu fails to open type in the following IP address into your web address bar http 192 168 3 1_ 4 When prompted enter the login and password Authentication Required Ea The server 192 168 3 1 requires a username and password The server says the High Power Router User Name Password LOGIN admin Login PASSWORD admin Copyright 2014 Loopcomm Technology Inc All rights reserved Welcome to the Smart Setup Wizard When the web menu appears click BASIC SETUP and NEXT to proceed with the Smart Setup Wizard I Welcome to the Dashboard The Smart Setup Wizard will guide you through the following settings 1 Internet Connection eo Internet Modem Your Broadband Modem is not connected to the Modem Port on the Router Attach your Modem and click below to configure the Router s Basic Settings 3 Wireless Connection A Welcome to the Basic Setup Wizard 2 System Clock If you are setting up the Router for the first time or if you currently do not have Internet access follow the intructions below If your Router is already conifgured with Internet access skip these steps and click Next or go to More Settings for access to advanced features A Check that your modem has already been rebooted by unplugging the power and backup battery if available for 30 seconds B Check that the modem is connected to the Router s Modem Port blue C Check that Antenna 1 Antenna 2 and Antenna 3 are
46. to block www google com simply type in google and the Dual Band Wireless Router will block all websites with the text google in the URL E Block Websites URL Filtering URL Filtering blocks users on your from accessing specific websites that you deem unsafe or inappropriate Enter a keyword or the actual web address below to begin blocking Note If you wish to block www google com simply type in google and the Router will block all websites with the text google in the URL Enable URL Filtering URL Address APPLY RESET Current Filter Table Delete Selected Delete All Reset Copyright O 2014 Loopcomm Technology Inc All rights reserved User Access MAC Address Filtering User Access allows you to deny access or allow access to specific users connecting to the network Each networking device has a unique address called a MAC address a 12 digit hex number By inputting the MAC address into the field you can define whether that device is allowed into your network or not allowed A MAC Address may sometimes be referred to as a Physical Address Most networking devices have their MAC Address located on a label on the actual device A User Access Control MAC Address Filtering Each networking device has a physical address known as a MAC address MAC Address Filtering blocks access to your network from computers or network devices based on their unique MAC address physical address To begi
47. upgrading Copyright 2014 Loopcomm Technology Inc All rights reserved Save Reload Settings Saving your current settings allows you to back up your current settings which may be reloaded at a later time This feature may be useful for testing new features and settings without having to worry about returning to a stable platform To save current settings a Click Save b Select a file name and location To load previously saved settings a Click Browse b Locate the previously saved settings file c Click Upload to restore the settings to the saved file Bi Save Reload Settings Save your current Router configurations to a file or reload previously saved configurations If needed you may also reset your Router to factory default settings Save Settings to File Load Settings from File Reset Settings to Default Copyright 2014 Loopcomm Technology Inc All rights reserved Password By default LP 8096 to require a password to log on to the Web page If you wish to enable a password to protect unauthorized Prevent unauthorized access to your Router s web based configuration menu by providing a user name access to the Web menu you may enter one here and password If no protection is necessary leave these fields blank and you will not be prompted for a login and password when accessing this web menu i Password New Login New Password Confirmed Password Copyright 2014 Loopcomm Tec
Download Pdf Manuals
Related Search