USER MANUAL V.1
Contents
1. DMX CHART DMX channels functions and their values 44 DMX channels DMX channel s functions and their values 44 DMX channels Mode Channel Value Function Mode Channel Value Function St Ba Ex St Ba Ex Shutter strobe PAN Movement 8bit 0 31 Led turn off i 0 255 Pan Movement 32 63 Led turn on Pan Fine 16bit 64 95 Strobe effect slow to fast f 0 255 Fine control of Pan movement 12 10 8 96 127 Led turn on TILT Movement 8bit 128 159 Pulse effect in sequences u a a 0 255 Tilt Movement 160 191 Led turn on Tilt Fine 16bit 192 223 Random strobe effect slow to fast i 0 255 Fine control of Tilt movement 224 255 Led turn on Speed Pan Tilt movement Dimmer intensity 0 225 max to min speed ir j 0 255 Intensity 0 to 100 2 3 g 226 235 blackout by movement Color Macro 226 235 no function 0 7 No function Pan Motor continuous rotation 8 39 rom RED to YELLOW 0 127 no function 40 71 rom YELLOW to GREEN 6 4 128 189 Forwards Pan rotation from fast to slow 72 103 rom GREEN to CYAN 190 193 No rotation a a X 104 135 rom CYAN to BLUE 194 255 Backwards Pan rotation from slow to fast 136 167 rom BLUE to MAGENTA Tilt Motor continuous rotation 168 199 rom MAGENTA to RED 0 127 no function 200 231 rom RED to WHITE 7 5 128 189 Forwards Tilt rotation from fast to slow 232 255 Crossfading colours from slow2. Address Set Dmx Addr A001 AXXX DMX address setting User Mode Stand Mode User s mode to change Basic Mode channel numbers 5 Extend Mode User Mode A g User Mode B 2 User Mode C Edit User Max channel Preset User modes PAN Status Addr via DMX ON OFF Add via DMX No DMX Mode Close Hold Auto Music Auto run if no DMX Pan Reverse ON OFF Pan Reverse movement Tilt Reverse ON OFF Tilt Reverse movement Pan Degree 630 540 Pan Degree Select Feedback ON OFF Movement Feedback Pan Tilt Spd Speed 1 4 Reset Pan Tilt Mic Sens 0 99 Sensitivity of Mic Hibernation OFF 01M 99M 15M Stand by Mode Service PIN Service PIN Password XXX Service Password 050 RDM PID KOK RDM PID Code Set IP XXX XXX XXX XXX lingNet Device ID Set LED BIN LED BINA LED BIN LED BINB LED BIN Set Device ID XX P Addr Fans Control Head Control Auto Head Fans Speed Mode High Selec Low Disp Setting Shutoff Time 02 lt 60m gt lt 05m gt Display shutoff time 2 Flip Display ON OFF Reverse 180 degree 2 Key Lock ON OFF ey Lock amp DispFlash ON OFF lo Signal Flash Signal Select DMX DMX WDMX Wireless DMX Art Net Art Ne LED Control Kling Net OFF lingNet confer Kling Net RGB ling Net confer RGB Kling Net RGBW ling Net confer RGBW Set Universe XX Art Net Universe NO Temp C F Celsius Temperature switch Fahrenheit between C F nitial Pos PAN XXX Initial effect position Wireless DMX Act amp Da
3. AYRTON Digital Lighting magicblade SUMMARY 4 oo NO OO NO LK A A Introduction Safety instructions Conditions of use Presentation and features Dimensions Description Installation instructions Installation method using truss hooks DMX512 connection Instructions for using the wireless internal DMX system Control Panel MagicBlade R control panel menu Option details Master Slave Mode settings Led mapping DMX Chart Error Messages Care and maintenance Technical Specifications Warranty USER MANUAL _ 3 magicblade INTRODUCTION Thank you for selecting the AYRTON MAGICBLADE R luminaire WARNING This product is not suitable for household use You now own a professional lighting unit that offers endless possibilities Before installing make sure that no damage was done to your luminaire during transport If this is the case do not use the product and immediately contact your authorized AYRTON dealer For your own safety and that of others please read this instruction manual carefully before installing the unit Anyone involved in installing operating or servicing the MAGICBLADE R must e Be a qualified authorized professional e Strictly follow the instructions in this user manual Please take the time to read this manual carefully and thoroughly before installing and operating the luminaire You should have a good knowledge of its operating conditions and all pertinent prod
4. Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Status Finally use the left right arrow keys to select Pan Tilt Spd Scroll through the different options using the left right arrows and press Enter to confirm Hibernation Standby mode The LEDs and the pan tilt motors will be powered down if the luminaire receives no DMX signal for 15 minutes default setting IF the DMX signal is restored after this time limit the luminaire will perform a RESET before resuming normal operation Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Status Finally use the left right arrow keys to select Hibernation Scroll through the different options using the left right arrows and press Enter to confirm USER MANUAL _ 10 magicblade SERVICE PIN WARNING For normal operation the Service pin menu information should not be changed Contact your dealer for more information Service PIN Allows you to enter a password to access the advanced options such as RDM PID Set IP Set Device IP Set LED BIN and Change to bin pwd 50 Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION
5. the SLAVE fixture would receive the program Auto Program Part 2 from the MASTER fixture To launch a program follow this procedure 1 Slave Settings SLAVE fixture adjustment Use the buttons to select Function Mode Press ENTER to confirm Use the buttons to select Set slave to Press ENTER to confirm Use the buttons to select Slave 1 Slave 2 or Slave 3 Press ENTER to confirm Press MODE ESC to return to the main menu 2 Automatic Program Run Use the buttons to select Function Mode Press ENTER to confirm Use the buttons to select Auto Program Press ENTER to confirm Use the buttons to select Master or Alone Master sets the fixture as the master Press ENTER to confirm Press MODE ESC to return to the main menu 3 Program selection for Auto Pro Part Use the buttons to select Edit program Press ENTER to confirm Use the buttons to select Select programs Press ENTER to confirm Select Auto Program Part 1 Auto Program Part 2 or Auto Program Part 3 for the Slave program to be sent Selecting Part 1 will cause the SLAVE to run the same program as the MASTER fixture Press ENTER to confirm Press MODE ESC to return to the main menu 4 Program selection for Edit Program Use the buttons to select Edit program Press ENTER to confirm Use the buttons to select Edit program Press EN
6. Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Disp Setting Finally use the left right arrow keys to select Key Lock Use the left right arrow keys to select ON or OFF Press Enter to confirm DispFlash Causes the display to flash as a warning that there is no DMX signal Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to access the Disp Setting submenu Finally use the left right arrow keys to select DispFlash Use the left right arrow keys to select ON or OFF Press Enter to confirm SIGNAL SELECT This menu allows you to choose what type of signal is used to control the fixture DMX Art Net or WDMX Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to access the Signal Select submenu Use the left right arrow keys to select the signal type used Press Enter to confirm USER MANUAL _ 11 magicblade LED CONTROL Defines whether the Kling Net Protocol is used to control the LEDs Kling Net is a protocol designed by Arkaos that simplifies use of their media server with LED panels if so equipped Access the menu b
7. menu and press Enter Finally use the left right arrow keys to select Service Pin Scroll up to 50 using the left right arrows and press Enter to confirm RDM PID Allows you to set the fixture s RDM PID code Access the menu by pressing the Mode Esc key Use the up down arrow keys to access the OPTION menu and press Enter Then use the left right arrow keys to select Service Pin Finally use the left right arrow keys to select RDM PID Use the up down arrow keys to change the value and left right to move from one number to the next Press Enter to confirm Set IP Allows you to change the fixture s IP address The fixture s default IP address is associated with the serial number Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Service Pin Finally use the left right arrow keys to select Set IP Use the up down arrow keys to change the value and left right to move from one number to the next Press Enter to confirm Set Device ID Allows you to change the fixture s identifier Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Service Pin Finally use the left right
8. You can select these functions by adjusting the channel Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the TEST menu and press Enter Then use the left right arrow keys to access the Home submenu Press Enter once again to select All or Pan amp Tilt TEST CHANNEL Tests each of the fixture s settings e g PAN TILT Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the TEST menu and press Enter Then use the left right arrow keys to access the Test Channel submenu The fixture then runs in test position Use the left right arrow keys to scroll through and test each setting MANUAL CTRL Allows you to access all the fixture s settings manually The shutter and the electronic dimmer are by default 100 open Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the TEST menu and press Enter Then use the left right arrow keys to access the Manual Ctrl submenu Use the left right arrow keys to scroll through and check each setting CALIBRATION Calibrates certain settings such as Pan Tilt and Zoom The password required to access the calibration function is 050 Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the TEST menu and press Enter Then use the left righ
9. spot can support at least 10 times the weight of the unit Connect the luminaire to the power source by the power cord INSTALLATION METHOD USING TRUSS HOOKS Refer to the following diagram when installing the MAGICBLADE R with truss hooks using omega brackets e Attach the clamp to the omega bracket using an M12 screw e Insert the quick lock fasteners of the first omega bracket into the respective holes on the base of the unit Turn the quick fasteners fully clockwise e Install the second omega bracket e Insert the safety cable through the holes at the bottom of the base and the truss or a stable attachment point Insert the end into the hole and tighten the safety screw Note The last step is very important to ensure that the luminaire does not fall DMX512 CONNECTION Connect the DMX input XLR connector cable of the luminaire to the DMX output female XLR connector of your controller You can connect multiple luminaires to this same DMX line in a daisy chain The DMX cable must be a shielded twisted pair that is equipped with male and female XLR connectors Refer to the following diagram when connecting the MAGICBLADE R luminaires in a daisy chain Address 41 Address 21 Address 1 WARNING To ensure maximum stability at a 100 120 VAC no more than six luminaires should be connected together A seventh luminaire should be connected to another power source Whe
10. Handle these cables with extreme caution while they are connected to a power source Your MAGICBLADE R conforms to Class 1 safety standards The unit must be grounded electrically Make sure that the power source connected to your MAGICBLADE R is switched off before attempting any work on it Installation and connection to an electrical source must be performed by an authorized installer AYRTON declines all responsibility should this luminaire be installed by an unqualified person Never disconnect your MAGICBLADE R by pulling on the power cable First unlock the connector lock ring on the power cable until it is fully disengaged and then gently pull on the connector to disconnect the cable Do not connect or disconnect the power cable of your MAGICBLADE R with wet hands At first use your MAGICBLADE R may give off an odor This is a normal occurrence that should dissipate after a few minutes of operation WARNING Donot connector disconnect the power cable at your MAGICBLADE R if the cable is energized This could cause arcing and damage your MAGICBLADE R requiring repair Be careful to power off your MAGICBLADE R by removing the power plug from the source before connecting or disconnecting the luminaire WARNING This unit contains Class 2 LED emitters EN60625 1 1994 This luminaire uses multiple high power Class 2 LED type Light Emitting Diode lamps Never look directly into the lamps if lit or stand directly in
11. address is the channel from which the luminaire listens to the digital control information sent by the DMX controller The start address must conform to the one recorded on the DMX controller to run the luminaire This address is the DMX value that appears on the luminaire s display You can set the same address for all the luminaires or some of them but you can also set a different address for each luminaire as needed If you do set the same address for all the luminaires they will all listen from the DMX channel you have set The instructions sent by the DMX controller will affect all luminaires at the same time If you set a different address per luminaire the DMX controller can control each independently If for instance the fixtures are preset in 20 channel DMX mode required for full control you will need to adjust the DMX address for the luminaires as follows The first unit with DMX address 001 the second with DMX address 021 20 1 the third with DMX address 041 20 21 etc INSTRUCTIONS FOR USING THE WIRELESS INTERNAL DMX SYSTEM 1 REQUIRED HARDWARE DMX512 controller LumenRadio wireless MAGICBLADE R luminaires with wireless receivers transmitter and 2 WIRELESS INDICATOR FIXTURE SCREEN e Solid green Connected to transmitter and receiving DMX data e Solid red No connection to transmitter 3 W DMX IN THE FIXTURE MENU This part of the menu allows you to select if the unit will b
12. by its handles Choosing the appropriate place to install the MAGICBLADE R is essential The following points should be observed e Do not expose it to a heat source e Do not install it near flammable materials e Be sure that dust or miscellaneous debris cannot clump around the body of the luminaire as this may interfere with its optimal cooling and proper operation e The MAGICBLADE R must be installed out of reach of the public and all persons not authorized to operate the luminaire We recommend a minimum distance of 20 cm between the outside surface of the light and the illuminated object The color mixture of the MAGICBLADE R can be improved if the illuminated surface is very close to the luminaire up to about 50 cm Due to the nature of its cooling principle you should never prevent air from circulating around the body of the luminaire You must provide a minimum clearance of 20 cm around your MAGICBLADE R to allow for cooling The MAGICBLADE R can be installed in a ground pit or any other confined enclosure only under certain conditions With this kind of installation a system of forced ventilation should be used up to allow air to circulate freely around the luminaire s The air must be constantly renewed because the luminaire cannot be operated in closed system Failure to comply with these requirements may destroy or prematurely wear the MAGICBLADE R and AYRTON cannot be held responsible Please consult your AYRTON deal
13. dust and residue on the air vents body and glass of the fixture may reduce efficiency and impair proper operation Before cleaning disconnect the power cable from source Use compressed air to blow away dust particles accumulated on and between the cooling fins at the rear of the luminaire s optical system Clean the glass of the fixture with a slightly damp soft cloth When necessary use a non alcohol based glass cleaner Never use harsh solvents WARNING Never use alcohol or any chemical agent to clean the optical system of an Ayrton product COMPLIANCE CHECK Your installation should be checked regularly by certified service center In addition the following should be checked once a year by a qualified technician e The fixture s attachment system must be correctly installed and show no sign of corrosion e The fixture s mounting bracket should not be distorted in any way or show any trace of corrosion e The safety cable should be attached at the appropriate spot e Mechanical parts should show no sign of wear e The electrical cables should show no sign of wear cuts or splices TECHNICAL SPECIFICATIONS OPTICAL e Optical efficiency 85 maximum e Opening angle of the beam 4 5 SOURCE e 7 high power multicolor 15 Watt LED emitters e Brightness up to 3200 lumen e Estimated lifespan of LED emitters 50 000 hours e Guaranteed no flicker effect perfectly suited for television applications and all
14. protective foam inserts f your 602 MAGICPANEL is not being used for a long period you should disconnect the luminaire from the power source Never dispose of the MAGICBLADE R in a rubbish bin Ensure that it is recycled Please consult the current legislation in your country on recycling electronic equipment WARNING The number of daisy chain or tandem connections to the MAGICBLADE R power input and output sockets on the luminaires is limited for safety reasons The maximum authorized number of connections is as follows with the power line protected by a 10A circuit breaker 16 MAGICBLADE R units on the same source at 230 VAC or 6 MAGICBLADE R units on the same source at 110 VAC PRESENTATION AND FEATURES MAGICBLADE R is a non waterproof moving head wash light IP20 protection rating using the latest generation of high performance of LED type lamps This luminaire can be controlled remotely by an external DMX512 signal The MAGICBLADE R incorporates multi chip LEDs using 4 colors Red green blue and white This color light luminaire operates on the CMY additive color principle and along with white light can potentially render a palette of 4 2 billion colors The MAGICBLADE R has a total of 7 LEDs that can be controlled independently The luminaire requires from 18 to 44 DMX channels to be controlled via an external command system that sends a DMX512 signal see below for details To adjust the settings on the
15. MAGICBLADE R i e DMX address DMX operating mode and other options a Remote Device Management RDM type DMX controller may be required The DMX RDM protocol is a universal widely used standard There are a multitude of RDM DMX controllers on the market from different manufacturers excluding AYRTON It is worth noting that an RDM DMX controller is not required to change the settings on the MAGICBLADE R A light console or any standard DMX type controller is sufficient USER MANUAL _ 5 magicblade The MAGICBLADE R consists of a metal frame and plastic covers The DESCRIPTION power connectors and DMX512 signal connectors are on the back of the fixture s base DIMENSIONS Bottom view 1 Collimator 2 LCD Display 3 Left button 4 MODE ESC button 5 Down button 6 Enter button 7 Right button 8 Up button 9 Antenna Wireless DMX 10 DMX512 output connector 5 pin Side view 11 DMX512 input connector 5 pin 12 RJ45 output connector 13 RJ45 input connector 14 Power source input connector 15 Power source output connector 16 Fuse holder INSTALLATION INSTRUCTIONS During installation please observe the instructions according to GB7000 15 EN60598 2 17 standards and other national standards applicable This luminaire should be installed by a qualified technician The fixture should be used in an environment with a temperature between 5 C and 45 C Do not operate the lumina
16. TER to confirm Use the buttons to select the desired program You can edit specific scenes in a given program Press ENTER to confirm Press MODE ESC to return to the main menu 5 Automatic Scene Recording Use the buttons to select Edit program Press ENTER to confirm Use the buttons to select Edit scenes Use the buttons to select the number of desired scenes maximum amount 250 scenes Press ENTER to confirm Press MODE ESC to return to the main menu Example Program 2 includes scenes 10 11 12 13 Program 4 includes scenes 8 9 10 Program 6 includes scenes 12 13 14 15 Auto Program Part 1 is Program 2 Auto Program Part 2 is Program 3 Auto Program Part 3 is Program 6 The 3 groups of SLAVE fixtures run the Auto Program function in the following sequence Part 1 Scene 10 Scene 11 Scene 12 Scene 13 Part 2 Scene 8S cene 9S cene 10 Scene 8 Part 3 Scene 12 Scene 13 Scene 14 Scene 15 LED MAPPING The diagram shows the order of the LED addresses from a front view of the luminaire and control panel from left to right Seen y nn USER MANUAL _ 14 magicblade
17. alue Ttl Life Hrs Shows the fixture s total number of hours of operation Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the INFO menu and press enter Then use the left right arrow keys to access the access the Time Info submenu Use the left right arrow keys to select Tit Life Hrs and press Enter to display the value Last Run Hrs Shows the fixture s length of operation since the last time this counter was reset Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the INFO menu and press Enter Then use the left right arrow keys to access the access the Time Info submenu Use the left right arrow keys to select Tit Life Hrs and press Enter to display the value USER MANUAL _ 12 magicblade Timer PIN The Timer PIN is the password required to reset the counter for Last Run Hrs The PWD is 038 Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the INFO menu and press Enter Then use the left right arrow keys to select Time Info Finally use the left right arrow keys to select Timer PIN Scroll through using the left right arrows until 038 appears and press Enter to confirm CLR LAST RUN After entering the Timer PIN you can reset the value for Last Run Hrs through th
18. arrow keys to select Set Device ID Use the left right arrow keys to change the value displayed Press Enter to confirm Set LED BIN Allows you to change the model of LED card used in the fixture The last part of the serial number indicates the LED card binning 6 binnings BINA BINB BIN B21 B23 BIN B25 B27 BIN B28 and BIN B22 Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Service Pin Finally use the left right arrow keys to select LED BIN Use the left right arrow keys to change the value displayed Press Enter to confirm Change to BIN This option makes it possible for several fixtures that do not have the same model of LED card to operate compatibly Simply select a reference BIN that will be used for each fixture Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Service Pin Finally use the left right arrow keys to select Change to bin Use the left right arrow keys to change the value displayed Press Enter to confirm FAN CONTROL Head Control Allows you to choose the fan speed on the fixture head The options are AUTO HIGH or LOW Access the menu by pressing the Mode Esc key Use t
19. e controlled by wireless DMX see WDMX in OPTION DETAILS Choose the WDMX option in the Signal Select submenu under the OPTION menu The fixture will always return the DMX signal through the XLR 5 output REST WDMX Antenna in the Wireless DMX submenu This function allows you to remove a luminaire from a wireless network e g to pair it with another transmitter 4 CONFIGURING THE WIRELESS SYSTEM e Connect the transmitter to the DMX controller e The fixture s indicator should default to red e Press the configuration button on the transmitter for 3 seconds Wait 5 10 seconds for the pairing to occur The wireless indicator on the receiver fixture should be green e Once pairing is achieved the receiver fixture retains the connection in memory When the installation is powered on pairing will be done automatically 5 REMOVE RECEIVER FROM TRANSMITTER T1 AND PAIR WITH ANOTHER TRANSMITTER T2 Case 1 Removing a receiver e Activate the REST WDMX function in the fixture menu see OPTION DETAILS e The wireless indicator on the fixture screen should be red The receiver fixture is now disconnected from transmitter T1 e Press the configuration button on transmitter T2 for at least 3 seconds and the unit will start to pair with the receiver fixture Case 2 Removing all receivers from transmitter T1 to pair all to transmitter T2 e Press the configuration button on transmitter T1 for at leas
20. er for more information on this type of installation No load should be placed on the MAGICBLADE R The fixture must not be installed in such a way as to allow a person vehicle or any object to run over or park on it Never lay or drop any hard heavy or blunt objects on the MAGICBLADE R This includes items made of glass or porcelain e g bottles dishware or glass beads The luminaire is made of materials such as plastic and extruded aluminum making it resistant but not unbreakable Objects made of hard materials such as steel or glass that fall on the unit may cause breakage of the plastic parts or the body AYRTON cannot be held responsible for the luminaire s broken plastic parts or body which are not covered under warranty The temperature of the room where the MAGICBLADE R is installed must never exceed 45 C Ta 45 C The MAGICBLADE R luminaire requires a 110 240 VAC supply voltage Check that your luminaires have been installed for an application that is compatible with this information Check that the bracket on which you hang or attach your MAGICBLADE R can sustain the weight of the luminaire 12 kg taking into consideration all necessary safety factors Do not use your MAGICBLADE R before being familiar with these recommendations and do not allow unqualified personnel to handle the product To transport your MAGICBLADE R we strongly recommend that you use the complete original packaging including the dense
21. g defects for the duration of one 1 year from the date of purchase This warranty does not cover the unit for evidence of physical shock or damage caused by abuse or any use not in accordance with the operating conditions set forth in the present user manual In addition cosmetic defects caused by the normal wear and tear of the unit are not covered under the warranty Any modification to the fixture will void the warranty AYRTON cannot under any circumstances be held liable for quality and conformity regarding the installation of this product which is the responsibility of the installer Broken glass lenses on the MAGICBLADE R and any damage that could arise thereof are excluded from the warranty Any possible cosmetic defects provided you report them to your AYRTON dealer upon unpacking the device and before use may be covered by the warranty Note The manufacturer is not responsible for any errors or omissions that may occur in this document All information contained in this manual is subject to change without notice USER MANUAL _ 18 magicblade USER MANUAL _ 19 AYRTON Digital Lighting www ayrton eu
22. he up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Fan Control Use the left right arrow keys to select the fan option Press Enter to confirm DISP SETTING Shut off Time Allows the fixture s LCD display to be turned off after a period of 2 to 59 minutes Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Disp Setting Finally use the left right arrow keys to select Shut off Time Use the left right arrow keys to change the value displayed Press Enter to confirm Flip Display Allows you to rotate the display by 180 This can be highly useful when the fixture is installed with the head facing down Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Disp Setting Finally use the left right arrow keys to select Flip Display Use the left right arrow keys to select ON or OFF Press Enter to confirm Key Lock Activates the automatic keypad lock If this function is enabled the keys will be automatically locked 15 seconds after exiting edit mode Hold the MENU key down for 3 seconds to deactivate this function Access the menu by pressing the
23. hutter or even remain in the state when the last DMX values Hold were received The default setting is Hold Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Status Finally use the left right arrow keys to select No DMX Mode Scroll through the different options using the left right arrows and press Enter to confirm Pan Reverse Reverses the PAN movement Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Status Finally use the left right arrow keys to select Pan Reverse Scroll through the different options using the left right arrows and press Enter to confirm Tilt Reverse Reverses the direction of the TILT movement Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Status Finally use the left right arrow keys to select Tilt Reverse Scroll through the different options using the left right arrows and press Enter to confirm Pan Degree Adjusts the amplitude of the PAN movement at 630 or 540 Access the menu by pressing the Mode Esc key Use the up dow
24. ire outside this temperature range The luminaire must be hung so that the weight of this unit multiplied by 10 can be sustained for 1 hour without causing the suspension system or the supporting structure to be deformed USER MANUAL _ 6 magicblade The installation must always be secured at a second attach point e g by a safety cable of the appropriate size Do not stand under the luminaire while it is being installed dismantled or serviced The operator must ensure that a qualified technician has approved the installation of the luminaire for safety before it is first operated Installation should be inspected once a year by a qualified technician WARNING The installation of this luminaire must be validated by a qualified technician before it is used for the first time The luminaire should be installed in a location where the public cannot touch walk or sit on the luminaire Suspending the luminaire and or installing it high up requires considerable experience e g calculating load selecting and adapting quality fastening materials and periodically inspecting the entire installation Without this skill and knowledge do not attempt to install this unit by yourself Improper installation may cause an accident resulting in personal injury or death WARNING The luminaire should be connected to an electrical source by a qualified electrician Before installing the luminaire make sure that the selected installation
25. is menu Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the INFO menu and press Enter Then use the left right arrow keys to access Clr Last Run submenu Use the left right arrow keys to select ON to validate the reset TEMP INFO Head Temp Shows the current temperature of the fixture head Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the INFO menu and press Enter Then use the left right arrow keys to access the Temp Info submenu Press Enter once again to display the temperature of the head SOFTWARE VER Displays the software version of the fixture Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the INFO menu and press Enter Then use the left right arrow keys to access the Software ver submenu Press Enter once again to display the software version NETWORK This menu directly displays the following network information for the fixture IP address subnet mask and MAC address Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the INFO menu and press Enter Then use the left right arrow keys to access the Network submenu Press Enter once again to display the information TEST HOME Allows you to reset the functions from a DMX controller
26. lf adjusting fan for reduced noise level in AUTO mode e User selectable air cooling modes CONSTRUCTION e Covers molded PC ABS thermoplastic class VO fire retardant e Chassis steel plates and aluminum e 2 handles for transport e Protection rating IP20 indoor use only e Finish Carbon black INSTALLATION e 2 OMEGA brackets with quarter turn locks included e Safety cable attachment OPERATING PARAMETERS e Operating positions all on floor or attached to a support e Maximum authorized ambient temperature Ta Max 45 C 113 F e Minimum authorized ambient temperature Ta Min 10 C 14 F e Minimum projection distance 0 2 m 8 inches DIMENSIONS e Product 571 mm x 266 mm x 184 mm L x H x D e Protective foam 625 mm x 295 mm x 250 mm L x H x D WEIGHT e Product 11 2 kg e Product in packaging with accessories 25 kg PRODUCT CODE e 015250 MAGICBLADE R AUTOMATED LUMINAIRE USER MANUAL _ 17 magicblade FOAM FOR FLIGHT CASE MAGICBLADE R is delivered in a carton packed with a dense protective foam surrounding the fixture This reusable protective shell is intended for a flight case that can be custom built for the luminaire AYRTON does not offer custom flight cases for the MAGICBLADE R This accessory is to be provided by the user The main dimensions of the protective shell appear in the following diagram 625 WARRANTY The AYRTON MAGICBLADE R fixture is guaranteed against manufacturin
27. line with the luminaire if close by Installation removal or replacement of the unit must be performed with power off to prevent any risk of glare and eye injury WARNING The fixture quickly becomes very hot during operation To avoid risk of burn never handle or adjust the luminaire while it is energized and after it has been lit for more than 10 consecutive minutes Some parts of the luminaire can reach a high temperature particularly the body radiator Turn off the luminaire and wait for it to cool before handling CONDITIONS OF USE Your MAGICBLADE R is a moving head luminaire equipped with multiple LEDs intended for professional use e g architectural stage television theater or museum lighting The MAGICBLADE R luminaire has an IP20 protection rating It is intended strictly for indoor use It must never be partially or fully submerged even USER MANUAL _ 4 magicblade temporarily Condensation may form on your MAGICBLADE R in the following cases e Immediately after turning on the heating e In places with fog or a high level of humidity e When the luminaire is suddenly moved from a cold to a warm environment or vice versa In such cases you must wait until the luminaire readjusts to the ambient temperature of the room where it will be installed for operation Do not shake the MAGICBLADE R while installing or handling Do not by pull the MAGICBLADE R by one of its cables to move it Lift the luminaire
28. n arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Status Finally use the left right arrow keys to select Pan Degree Scroll through the different options using the left right arrows and press Enter to confirm Tilt Degree Adjusts the amplitude of the TILT movement at 540 or 270 The 540 function allows you for instance to add an accessory to the rear part of the fixture head Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Status Finally use the left right arrow keys to select Tilt Degree Scroll through the different options using the left right arrows and press Enter to confirm Feedback Readjusts the PAN and TILT positions automatically in the event of accidental shifting due to a physical shock Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to select Status Finally use the left right arrow keys to select Feedback Scroll through the different options using the left right arrows and press Enter to confirm Pan Tilt Spd You can choose between four movement speeds from Speed 1 to Speed 4 The Speed 1 setting is the fastest
29. n the power voltage is 220 240 VAC a maximum of sixteen luminaires can be connected together in this way A sixteenth luminaire should be connected to another power source USER MANUAL _ 7 magicblade DMX512 CONNECTION WITH TERMINATION PLUG For installations where the DMX cable must extend over long distances or if it is located near areas with major electrical disturbance it is recommended to use a DMX termination plug This helps prevent luminaires from malfunctioning due to interference The DMX termination plug composed simply of a male XLR input connector with a 120 Ohm resistor is soldered between pins 2 and 3 This plug must be connected to the DMX output of the last luminaire in the chain Refer to the following diagram PIN 3 PIN 2 USING DMX VIA ART NET To control the MAGICBLADE R DMX via ART NET the fixtures must be interconnected with CAT5 RJ45 cable Be careful to enter all necessary information into the ART NET universe being used and specify in the menu that the MAGICBLADE R is being controlled through ART NET see OPTION DETAILS in the OPTION menu WARNING The MAGICBLADE R can only read the first twenty universes of an ART NET packet If you have more than 20 universes in your network you must use a configurable switch to filter each RJ45 output THE LUMINAIRE S DMX ADDRESS SETTING All luminaires have a DMX start address correctly set when using a DMX signal to control them The DMX start
30. nufacturer for service and do 1 14 Led trun off not attempt to repair the luminaire yourself 15 30 Chase 1 3146 Chase2 PAN movement Er A Je PAN yoke movement error This message will appear after the reset 6378 _ Chase4 if the yoke s magnetic indexing circuit malfunctions failed sensor or 19 94 Ds magnet missing or the stepping motor is defective also caused by its 95 110 Chase 6 16 14 12 111 126 Chase 7 127 142 Chase 8 143 158 Chase 9 159 174 Chase 10 175 190 Chase 11 191 206 Chase 12 207 222 Chase 13 223 238 Chase 14 239 255 Chase 15 driving IC on the main PCB The PAN movement does not return to the default position after the reset TILT movement Er TILT head movement error This message will appear after the reset if the head s magnetic indexing circuit malfunctions sensor failed or magnet missing or the stepping motor is defective also caused by its driving IC on the main PCB The TILT movement does not return to the default position after the reset Chase Speed 0 125 Fast to Slow Backward 17 15 13 126 130 Stop Speed 0 131 255 Slow to Fast Forward ee chase Fade CARE AND MAINTENANCE 0 255 Fade Chase Reset internal programs The care and maintenance of your MAGICBLADE R should be ensured 0773 Normal by a qualified technician Your MAGICBLADE R requires regular servicing ae Al motorreset The frequency depends essentially on i
31. r to the table above Note You can exit this menu at any time by pressing Mode Esc repeatedly until you return to the home screen ADDRESS Allows you to change a DMX address from the fixture s control panel Access the menu by pressing the Mode Esc key Go to the ADDRESS menu and press Enter then find Set DMX Address Use the up down arrows to scroll through until you locate the desired address and press Enter to confirm MODE USERS MODE Allows you to select the DMX mode from the following Basic Mode 18 DMX channels Standard Mode 20 DMX channels Extended Mode 160 DMX channels User Mode A User Mode B User Mode C Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the MODE menu and press Enter Then from User Mode choose one of the 6 modes above Consult the CHART DMX table for more information on Basic Standard and Extended Mode User Modes A B or C are user definable EDIT USER A B C To customize the mode go to MODE and select Edit UserMode A B or C and press Enter Scroll through each setting and press Enter to set the desired address OPTIONS STATUS No DMX Mode Defines the fixture s state when there is no command signal from the DMX controller The fixture can either launch a program automatically close the s
32. t 5 seconds to reset pairing with receiver fixtures e All green indicators on the receiving fixtures will turn red indicating that the receiver fixtures are no longer paired with transmitter 11 e Press the configuration button on transmitter T2 for at least 3 seconds to pair it with the receiver fixtures Note e Unpair receiver fixtures from transmitter after use USER MANUAL _ 8 magicblade e Do not connect the DMX console to the fixture when it is controlled via wireless This could cause interference between the two modes of operation CONTROL PANEL MENU OPTIONS A large number of settings are accessible from the fixture s control panel A good working knowledge of it will enhance the fixture s possibilities You can access the Main Menu by pressing the mese key until the display flashes Cycling through the menus is performed by pressing the A Q or keys as required Press the key to select the desired menu Change the selection by pressing the A V or keys Confirm your selection by pressing the rie key Exit a menu at any time by pressing the key Notes You can return to the display by pressing the or keys from the basic display If the screen fails to respond hold the Mode Esc key down for at least 3 seconds to free up the display The fixture s menu functions are described in the following table USER MANUAL _ 9
33. t arrow keys to access the Calibration submenu Press Enter once again to access the password 050 and press Enter to confirm Use the left right arrow keys to move from one setting to another and press Enter to access the calibration function of the setting Finally press Enter to confirm the change PRESET SELECT PROG Allows to choose the program for Program Run EDIT PROG Allows you to edit internal programs DIT SCENES lows you to edit scenes within the internal programs gt m SCENES INPUT The luminaire features a DMX recorder which can receive the scenes programmed on your DMX controller Set the desired number of scenes from the control panel Then run the scenes from your controller They will be automatically transmitted to the MAGICBLADE R MASTER SLAVE MODE SETTINGS A MASTER fixture can send up to 3 different sets of data to a SLAVE fixture e g a MASTER fixture can control 3 different SLAVE fixtures which will each perform 3 different programs The MASTER fixture sends the 3 programs in a continuous loop The SLAVE fixture receives data from the MASTER fixture according to the group to which the SLAVE fixture is assigned For example if the SLAVE fixture has been assigned to Slave 1 in the menu Set to Slave the MASTER fixture sends Auto Program Part 1 to this SLAVE fixture If it USER MANUAL _ 13 magicblade was assigned to Slave 2
34. t right arrow keys to change the value Press Enter to confirm WIRELESS DMX This menu allows you to reset wireless pairing Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to access the Wireless DMX submenu Use the left right arrow keys to activate the setting Press Enter to confirm TRIGGER DMX Value Disp Allows you to view the DMX value received for each setting The ALL option will display only the setting being edited Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to access the Trigger submenu Use the right left arrow keys to select DMX value Disp Use the left right arrow keys to select which setting to display Press Enter to confirm Set To Slave Sets the fixture to SLAVE Mode for receiving instructions from a master luminaire see Master Save mode settings below Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to access the Trigger submenu Use the right left arrow keys to select Set To Slave Use the right left arrow keys to define whether the fixture is Slave 1 Slave 2 or Sla
35. ta Out Act amp Data Out Rest WDMX Reset Wireless DMX Mem rigger DMX Value Disp PAN DMX value display Set To Slave Slave1 Slave2 Slave3 Slave setting Auto Program Master Alone Auto program Music Ctrl Master Alone Music control Reset Default ON OFF Restore factory sett ime Info Current Time XXXX Hours Ti Life Hrs XXXX Hours Last Run Hrs XXXX Hours Timer PIN Password XXX Clr Last Run ON OFF Temp Info Head Temp XXX C F Software Ver V1 0 Software version Network IP Mask Mac Network setting Home All Reset all motors Pan amp Tilt Reset Pan amp Tilt Test Channel PAN Test function Manual Ctrl PAN XXX Fine adjustment of 2 parameters Calibration Password Password 050 PAN Calbrate and adjust the i effects to standard right position Select Prog Prog Part 1 Program 1 10 Program 1 Select programs to be run Prog Part 2 Program 1 10 Program 2 Prog Part 3 Program 1 10 Program 3 Edit Prog Program 1 Program Test Testing program z Step 01 SCxxx Program in loop 8 Program 10 Step 64 SCxxx Save and exit Edit Scenes Edit Scene 001 Pan Tilt Save and automatically Edit Scene 250 Fade Time return Secne Time manual scenes edit Input By Outside Scenes Input XX XX Automat scenes rec magicblade MAGICBLADE R CONTROL PANEL MENU OPTION DETAILS The following section provides details on the options that can be selected through the control panel menu Refe
36. to 0 255 Blue 0 Black 255 100 Blue 155 159 Rainbow 44 ld 160 164 Rainbow12 0 255 White 0 Black 255 100 White USER MANUAL _ 15 magicblade DMX channels functions and their values 44 DMX channels ERROR M ESSAG ES Mode Channel Value Function st Ba Ex When you turn on the MAGICBLADE R it will first perform an automatic Color Presets reset The display may show Err channel is XX indicating there is 165 169 Rainbow13 a problem with one or more of the channels XX represents channel 170 174 Rainbow14 1 2 3 4 5 or 6 which contain the testing sensor for positioning For 175 179 Rainbow15 example the message Err channel is Red LED all arrays indicates an 15 13 11 180 184 Rainbow16 error in channel 1 If there is an error on channel 1 and channel 3 at the T 8 9 185 189 Rainbow same time the following error message may appear Err channel is Pan 190 194 Rainbow movement Err channel is Tilt movement The system will flash twice 195 199 Rainbow and the fixture will generate a second reset If the error message persists 200 255 Reserved after more than two resets the channels showing errors will not work Eee Color Presets Dimmer properly but the other channels will function normally 0 255 Dimmer 100 to 0 Chase Patterns Please contact your authorized dealer or ma
37. to fast 190 193 No rotation Color Presets 194 255 Backwards Tilt rotation from slow to fast 0 4 No function Red LED all arrays 5 9 White2700k 8 S 0 255 Red 0 Black 255 100 Red 10 14 White3200k Green LED all arrays 15 19 White4200k a 0 255 Green 0 Black 255 100 Green 20 24 White5600k Blue LED all arrays 25 29 White6500k id i 0 255 Blue 0 Black 255 100 Blue 30 34 White8000k White LED all arrays 35 39 Yellow u j 0 255 White 0 Black 255 100 White 40 44 Magenta Red LED array 1 45 49 Cyan 0 255 Red 0 Black 255 100 Red 50 54 Salmon Green LED array 1 55 59 Turquoise 0 255 Green 0 Black 255 100 Green 60 64 Light Green Blue LED array 1 65 69 Steel Blue 0 255 Blue 0 Black 255 100 Blue 70 74 Orange White LED array 1 75 79 Straw 0 255 White 0 Black 255 100 White gt ae n 80 84 Pale Lavander Red LED array 2 85 89 Pink 0 255 Red 0 Black 255 100 Red 90 94 Red Green LED array 2 95 99 Green 0 255 Green 0 Black 255 100 Green 100 104 Blue Blue LED array 2 105 109 Rainbow1 0 255 Blue O Black 255 100 Blue 110 114 Rainbow2 White LED array 2 115 119 Rainbow3 0 255 White 0 Black 255 100 White 120 124 Rainbow4 125 129 Rainbow5 j Red LED array 7 130 134 Rainbow6 0 255 Red 0 Black 255 100 Red 135 139 Rainbow7 D Green LED array 7 140 144 Rainbow8 0 255 Green 0 Black 255 100 Green 145 149 Rainbow9 3a Blue LED array 7 150 154 Rainbow
38. ts operating conditions and 8587 __ Scan motor reset environment Intensive use in a dusty environment or a lack of ventilation 88 90 _ no function around the fixture may disrupt operation result in overheating and cause 91 93 no function damage that is not covered by the warranty 94 96 no function 20 48 16 97 99 no function W ARNIN G 100 119 Internal program 1 secne1 8 of EEPRO 120 139 Internal program 2 secne9 16 of EEPROM 140 159 Internal program 3 secne17 24 of EEPROM 160 179 Internal program 4 secne25 32 of EEPROM 180 199 Internal program 5 secne33 40 of EEPROM UPDATING THE LUMINAIRE Disconnect from mains before servicing 200 219 Internal program 6 secne41 48 of EEPROM 220 239 Internal program 7 secne49 56 of EEPROM Ayrton is continually upgrading this product line It is therefore possible 240 255 Music Control secne of Program 1 that a new software version is available that will increase the unit s capabilities Updates are performed using Ayrton s update box Contact your dealer for more information To display the version of your go into the Info menu and select Software version see options details under the INFO menu It is advisable to use the same software version for multiple fixtures USER MANUAL _ 16 magicblade CLEANING Your MAGICBLADE R requires cleaning at regular intervals Be aware that accumulated
39. uct information After you have become familiar with this manual we recommend that you keep a copy for future use All the information found in this manual is subject to change without notice AYRTON reserves the right to modify and upgrade its range of products with no obligation to integrate these changes into products already sold SAFETY INSTRUCTIONS Please read the safety instructions and warnings in this manual carefully before installing and operating the MAGICBLADE R WARNING Risk of electric shock Use caution when handling This luminaire requires high voltage which can result in electric shock The MAGICBLADE R left our factory in perfect working condition However if you notice a defect immediately contact your authorized AYRTON dealer before use The manufacturer cannot be held responsible for damages caused by a failure to follow the safety installation or assembly instructions contained herein or by any modification made to the luminaire Failure to observe the safety installation or assembly instructions contained herein or any modification made to the MAGICBLADE R luminaire will render the warranty null and void Check that the supply voltage does not exceed the maximum authorized limit Check that your electrical installation complies with current standards In all cases make sure that the power cables attached to your MAGICBLADE R have not been damaged due to cuts and splices or crushed in any way
40. ve 3 accordingly Press Enter to confirm Auto Program Allows you to run an internal program a sequence of scenes by selecting whether the fixture is operating alone or as a master Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to access the Trigger submenu Use the right left arrow keys to select Auto Program Use the right left arrow keys to select whether the fixture is Alone or Master Press Enter to confirm Note See AUTO menu to create internal programs RESETDEFAULT Restores the factory default settings on the fixture Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to access the ResetDefault submenu Use the right left arrow keys to select ON to perform a reset to defaults Press Enter to confirm INFO TIME INFO Current Time Shows the number of hours the fixture has been operating since it was powered on Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the INFO menu and press Enter Then use the left right arrow keys to access the Time Info submenu Use the left right arrow keys to select Current Time and press Enter to display the v
41. video recorded events COLORS e System of 4 color mixing red green blue and white ensuring a high color rendering index CRI e Uniformly produced light without shadows and offering rich saturated shades and pastel hues in 4 29 billion colors 8 bit resolution e Virtual color wheel including white light presets e Fixed colors and reprogrammable dynamic color change DIMMER STROBE e Electronic dimmer for light adjustment from 0 to 100 without color change 16 bit e High speed strobe effect in white or color at 1 to 25 flashes second e Pre programmed variable strobe effects SOFTWARE FEATURES e Full menus for setting DMX address and advanced functions e Compatible with the DMX RDM Remote Device Management protocol e Pre programmed macro modes e Information menu including timer temperature software version etc CONTROL e USITT DMX512 e Automatic features for managing your luminaire without a DMX console e DMX RDM compatible e Integrated control panel with LCD display and 6 buttons e DMX512 input output e DMX adapter cables with XLR5 connectors included e Choice of 3 DMX modes from 18 to 44 channels e Wireless System LumenRadio wireless CRMX RDM receiver POWER e Electronic power distribution with Power Factor Correction PFC from 110 240 VAC 50 60 Hz e 200 Watt maximum power e Power supply via powerCON TRUE1 connector e Supplied AC power cable COOLING e Advanced forced air cooling system e Se
42. y pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to access the LED Control submenu Use the left right arrow keys to activate the Kling Net option if desired Press Enter to confirm SET UNIVERSE Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to access the Set Universe submenu Use the up down arrow to scroll through until you locate the desired address and press Enter to confirm TEMP C F Allows you to select the unit of measurement for the temperature values in either Celsius or Fahrenheit Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to access the Temp C F submenu Use the left right arrow keys to select the unit of measurement Press Enter to confirm INITIAL POS Controls the initial position of the fixture s effects Access the menu by pressing the Mode Esc key Use the up down arrow keys to reach the OPTION menu and press Enter Then use the left right arrow keys to access the Initial Pos submenu Use the left right arrow keys to select the desired setting press Enter and use the lef
Download Pdf Manuals
Related Search