USERS GUIDE
Contents
1. the 2 indicates a STANDARD level and the 3 indicates a HIGH detection level After selecting the desired level press the START key to save the setting and exit from the setting mode 4 MAGNETIC COUNTERFEIT DETECTION SETTING Only available for the model with 2MG NOTES Magnetic is a device that is useful in detecting forgeries only when the currency being counted is printed with magnetic ink as a security feature Most commonly found on USA s and Italian Lira This feature will examine specific areas of the bank note surface for the presence of a magnetic field and where this is low or absent the machine will STOP the Batch Display will show and an audible Buzzer Alarm to indicate that a possible forgery is present As the machine has stopped only because of the possibility of a counterfeit being present you should then remove the last top note to have arrived in the Stacker area for detailed examination Press the CFA key two times to select the Magnetic Counterfeit Detection on or off the display will show NC 350A UV 2MG 3D L5 3 3 8 G9 08 C9 G3 09 C93 C9 When the Display shows CF 1 the Magnetic Counterfeit Detection is on Press the MAG key again the display will show CF 0 the Magnetic Counterfeit Detection is off and the red LED indicator on the MAG key will be off After selecting the desired level press the START key to save the setting and exit from the setting mode2. the prevailing conditions and can advise you of the optimum settings for your area in conjunction with your own experimentation By pressing the ADD key for five seconds the machine will enter into the Double Detection Setting The display will show NC 350 UVi2MG 3D GJ 93 C8 9 09 Ce Press the LEVEL key to sequentially change the Double Detection DD level The default d 2 setting will change through d 1 LOW d 2 STANDARD and d 3 HIGH After selecting the desired level press the START key to save the setting and exit from the setting mode 6 SPEED SETTING NOTE It is most important to appreciate that the counting speed you select is crucial when processing bank notes and that the speed should be varied according to condition The simple rule is that the better the quality the faster you can count currency without nuisance stops When the bank notes being counted are in a distressed condition and lacking in dimensional stability the low speed of 600 notes per minute should be selected Counting at the highest speed of 1 500 notes per minute should only be used for bank notes in new to very good condition By pressing the SPEED key the machine will enter into the SPEED system feature The display will show NC 350A UV 2MG 3D nn C8 C8 C2 C9 9 C9 Users Guide for NC 350A Currency Counter 9 Press the SPEED key to change the d
3. 5 DOUBLE DETECTION SETTING NOTES Detecting that two bank notes have passed through the machine one on top of the other and therefore suggesting a possible miscount is the function of the Double Detection DD system This feature operates by measuring the amount of light that penetrates each bill as it is being counted and compares this measurement with the known signal from a single note If the signal is significantly reduced the machine will STOP an Audible Alarm will sound and the Batch Display will show db All bills must be removed and recounted The machine will force a recount because by definition the count displayed cannot be assumed as accurate This also applies in the case of a suspected Chained note Chaining is where only part of a following bank note overlaps the one being counted Users Guide for NC 350A Currency Counter 8 2 Correctly setting the Thickness Control Knob will eliminate unnecessary cases of these incidents 3 The DD system defaults to d 3 at switch on This is the standard setting recommended for use when the quality of the bank notes is consistent Very dirty currency and or where the bills being counted vary widely in their condition are provided for by the following pre set DD levels to enable the machine to run smoothly without frequent false or nuisance stops These positions are d 1 LOW d 3 STANDARD and d 5 HIGH Your local distributor will be aware of
4. feed Remove the jammed note by pressing the START key H A partial or folded note has been Remove the partial or folded note and press the START key to HF2 detected continue the count Notes in the Hopper are misaligned Realign the notes in the Hopper H Abnormal width note s have been Remove the abnormal note s Hd2 detected Press the START key to continue the count Ld U A F1 91 CH1 A chained or abnormal note has Remove the chained abnormal note s CH2 been detected Adjust the Feed Gap for the correct setting 1 d1 F1 b Abnormal length note s have been Remove the abnormal note s Suspect counterfeit note has been Remove the suspected counterfeit note and press the RS key to Ud2 detected by the Ultraviolet detection continue the count Incorrect UV light sensitivity setting Adjust the UV detection level according to the note characteristics C Suspect Counterfeit note has been Remove the suspected counterfeit note and press the RS key to detected by the magnetic sensor continue the count Adjust the MG level according to the characteristics d Double or overlapped notes have Take out all the notes from the Stacker remove the double or db2 been detected overlapped note from the bundle put the bundle back into the Hopper to recount Incorrect Feed Gap setting Adjust Feed Gap to proper setting Incorrect Double Detection level Adjust the Double Detection level according to the note setting characteristics of
5. OLYMPIA MODEL NC 350A Series CURRENCY COUNTER USERS GUIDE CONTENTS eContents Page This Page eGeneral Information eMachine Overview eTechnical Specification slInitial Operation Steps eFunction Setting e Length Detection Setting e Width Detection Setting UV Counterfeit Detection Setting e Magnetic Counterfeit Detection Setting Double Detection Setting e Speed Setting e Counting Mode Setting e Dustproof Cover setting Maintenance Routines e Troubleshooting Users Guide for NC 350A Currency Counter 1 10 12 GENERAL INFORMATION Before you operate the machine please read this manual carefully Do not operate the machine until you understand the contents of this document Should you have any doubts please contact your local distributor or sales agent for further advice In the NC 350A series there are three models with various functional options e NC 350A The Basic Model e NC 350A UV With Ultraviolet Counterfeit Detection e NC 350A 2MG With Magnetic Counterfeit Detection e NC 350A UV 2MG With Ultraviolet amp Magnetic Counterfeit Detection e NC 350A UV 3D With Ultraviolet amp 3D Counterfeit Detection e NC 350A 2MG 3D With Magnetic amp 3D Counterfeit Detection e NC 350A UV 2MG 3D With Ultraviolet Magnetic amp 3D Counterfeit Detection MACHINE OVERVIEW Carrying Handle Right Cover Thickness Knob Stacker Vanes Stack Plate Control Panel Left Cover Note Guide
6. Plate DOM ON Rear Cover 10 Power Switch 11 Power Socket With Fuse 13 Dustproof Cover 11 Users Guide for NC 350A Currency Counter 2 TECHNICAL SPECIFICATION Counting Speed Hopper Capacity Suitable Note Size Operation Mode Power Consumption Power Requirements Dimensions Weight 1500 pcs min High Speed 1000 pcs min Standard Speed 600 pcs min Low Speed 200 pcs 130 x 60 190 x 80mm Double Detection Mode Accumulation Counting Mode Ultraviolet Detection Mode Option Magnetic Detection Mode Option Length Detection Mode Option Width Detection Mode Option Remote Display Option RS232 Communication Interface Option 50 Watts Operating 110 or 220 or 240 Volts 50 60Hz 320 L x 330 W x 320 H mm 7 5 Kg Users Guide for NC 350A Currency Counter 3 INITIAL OPERATION STEPS CAUTION Before you turn on the machine please ensure you remove ALL Notes from the Hopper and Stacker areas Turn ON the Power Switch on the rear of the machine The machine will enter a Self Test mode whereby the display will show NC 350A UV 2MG 3D 6 6 6 6 s CJ GJ GJ C9 C3 C3 C9 GJ The machine Motor systems will run for approximately 1 second and then if correct the Motors will stop and the display will change to show d oa en J NC 350A UV 2MG 3D 8 C9 CJ C9 eg When the machine leaves the factory the Default F
7. e key for five seconds again the display will show dp 0 The automatic function will be turned off Users Guide for NC 350A Currency Counter 11 MAINTENANCE ROUTINES Please maintain the machine via this simple daily procedure 1 Turn the Main Power Switch OFF and disconnect the Mains Power Cord from the rear of the machine 2 Using the brush provided clean the central Hopper Sensor the two Stack Sensors Hopper area and the Stacker area The photograph below shows the location of these devices Hopper sensor Friction Roller Feed roller Durm Roller Stack sensor Users Guide for NC 350A Currency Counter 12 Additionally please maintain the machine using this relatively simple monthly routine 1 Turn the Main Power Switch OFF and disconnect the Mains Power Cord from the rear of the machine 2 Using a piece of clean lint free cloth and an approved non toxic solvent fluid carefully clean the surfaces of the following parts which are identified in the two photographs below Do not allow any fluid to come in contact with ANY electrical parts Transfer Rollers Friction Rollers Feed Rollers Drum Rollers Stacker Sensor Central Hopper Sensor and the Outer Plastic Covers Transfer sensor Transfer Rollers Locations Component Locations Users Guide for NC 350A Currency Counter 13 Troubleshooting J Incorrect Feed Gap setting Adjust the Feed Gap for the correct setting There is a jammed note in the
8. efault SPEED setting if required There are three selectable speed 600pcs min Low 1000pcs min Standard and 1500pcs min High After selecting the desired speed press the START key to save the setting and exit from the setting mode 7 COUNTING MODE SETTING Auto Manual Start Mode By pressing the START key for five seconds the machine will enter into the START system feature The display will show NC 350A UV 2MG 3D 5 23 8 G9 C9 CJ C3J 8 C9J Press the two numeric keys 0 amp 1 to select the Auto Manual Start Mode Select 1 to enter into the Auto Start Mode Select 0 to enter into the Manual Start Mode After selecting the desired level press the START key to save the setting and exit from the setting mode CONTINUOUS COUNTING MODE When the digits of small LED Display shows the machine is in the Continuous Counting Mode If you place some notes in the Hopper the machine will count the notes until the Hopper is either empty or stops whenever an Error occurs during the process BATCH COUNTING MODE Input your desired batch number by using the ten numeric keys For example if you want to set the batch number to 20 just first press the numeric key 2 and then press the numeric key 0 The display will show NC350A UV 2MG 3D 2 pe Us Dus ee Doe oJ a La G C8 03 gt C9 Users Guide for NC 350A Currency Counter 10 If
9. gh the WD fe ature will also cause the machine to STOP if the bill is larger 1 When opting to use this feature from the H 0 OFF position there are many available settings to choose from 3 H 5 H 7 9 These numbers indicate the millimetre mm difference in the narrow dimension size between the denominations of your bank notes It is important to know that you should measure the difference beforehand and set the machine to detect to the nearest of your differential Your local Distributor will readily provide guidance on domestic currency settings By pressing the 3 D key two times the machine will enter into the Width Detection Setting The Users Guide for NC 350A Currency Counter 6 display will show NC 350A UV 2MG 3D zi CJ GJ 3 GJ 063 C69 CJ G9 GJ CS The selectable range of the Width Detection Accuracy is 3mm 5mm 7mm 9mm and off You can select the Width Detection Accuracy simply by pressing the corresponding numeric keys Turn off this function by pressing the key 0 After selecting the desired level press the START key to save the setting and exit from the setting mode When both the Length Detection Function and the Width Detection Function are turned off the red LED indicator on the 3 D key will be off 3 UV COUNTERFEIT DETECTION SETTING Only available for the model with UV NOTES 1 The vast majority of the world s bank notes are printed on a quality of
10. gth Detection LD is an optional feature of the NC350A series currency counter It is principally used to identify the denomination of the bank notes being counted where the particular national currency has a significant 3 mm difference in length between denominations 2 This system will allow reasonable latitude for bent missing bill corners but will not ignore extreme vertical edge errors or misalignment 3 Correct equidistant positioning of the Note Guides will greatly assist the machine to feed the bank notes By pressing the 3 D key the machine will enter into the Length Detection Setting The display will show NC 350A UV 2MG 3D 6 GJ GJ 3 G3 03 5 GJ C9 The selectable range of the Length Detection Accuracy is 3mm 5mm 7mm 9mm and off You can select the Length Detection Accuracy simply by pressing the corresponding numeric keys Turn off this function by pressing the key 0 After selecting the desired leve press the START key to save the setting and exit from the setting mode 2 WIDTH DETECTION Only available for the model with 3D NOTES The Width Detection WD is measuring the smaller dimension of the bank note It then compares this information with preceding bills in the present count run in order to largely eliminate the possibility of smaller denominations being included in the count in error This usually happens when small notes are hidden within a bundle of larger ones Althou
11. ink and thickness properties 1 Notes still in on the machine when Remove notes switched on Dirty Hopper or Stacker sensor s Clean all sensors Uv bad The detection system comprising Replace the UV lamp the UV Sensor or the CPU PC Board the UV lamp UV Sensor or the Main Maintenance engineer tasks CPU PC Board are suspect NOTE Counting is stil possible under this condition but the UV Counterfeit Detection system is inoperative The error code of xx1 means that the suspicious note is on the top of the bundle in the stacker The error code of x1 means that the suspicious note is the second one of the bundle in the stacker Users Guide for NC 350A Currency Counter 14 ek In the interests of our ongoing policy of continual product improvement specifications are subject to change without prior notice
12. ote feeding will become erratic To check and adjust the Feed Gap to counteract this simple wear condition please use the following procedure 1 Manually insert a genuine bank note into the Feed Gap and pull it rearwards if you did not feel any resistance whilst removing the note this indicates the gap is too wide If you feel the resistance is very strong it indicates the Feed Gap is too narrow When the machine leaves our factory the initial setting of the Thickness Dial is 8 2 Ifthe Feed Gap is found to be too wide please adjust the Thickness Knob which is mounted on the right side cover clockwise to slowly reduce the Feed Gap until the proper slipping resistance is achieved with your bank note 3 Ifthe Feed Gap is found to be too narrow please adjust the Thickness Knob counter clockwise to increase the feed gap until the proper slipping resistance is achieved with your bank note The machine will start counting automatically The machine will stop automatically under the following Conditions notes in the Hopper have been counted The machine count has achieved the pre set batch quantity When an error occurs An Error Code message will be shown on the display Please refer to the Troubleshooting Error Code table at the end of this Users Guide Users Guide for NC 350A Currency Counter 5 Function Setting 1 LENGTH DETECTION Only available for the model with 3D NOTES 1 Len
13. paper designed to withstand frequent handling and extend the time in circulation This specification normally means that they are printed on a high quality linen based paper which has low fluorescence characteristics Because the majority of counterfeit bank notes are printed on poorer quality papers which have been bleached and therefore fluoresce UV detection is normally the most useful method of helping to find forged bills at the speed at which a currency counter operates 2 Asthe machine has stopped because of the possibility of a counterfeit being present you should then remove the last top note to have arrived in the Stacker area in order to make a decision on the validity of the bill by closer visual examination 3 Most users will find the default position of U 2 Standard to be correct for their requirements Some experimentation using a lower or higher setting may in exceptional circumstances be necessary Your local Distributor will be able to provide guidance if required By pressing the CFA key the machine will enter into the UVD system feature The display will show NC 350A UV 2MG 3D y CFA START CG Cs C9 5 Users Guide for NC 350A Currency Counter 7 Press the UVD keys to change the default UVD detection level setting if required The indicated U 2 will now change through U 3 0 U 1 and U 2 then recycle sequentially The 0 indicates OFF the 1 indicates a LOW detection level
14. unctions are set as follows UV Counterfeit Detection UVD Uv 2 Only for the model with UV MaGnetic Counterfeit Detection Off Only for the model with IMG Counting Speed As Last User Selection Double Detection dd 2 Length Detection Ld 5 Only for the Model with 3D Width Detection Hd 5 Only for the Model with 3D Counting Mode As Last User Selection Auto Manual Start Auto Start Switch to AutoStart when turn on the power again Users Guide for NC 350A Currency Counter 4 If the various function settings of the machine were pre set by the previous operator the machine will automatically default back to these previous selections when you turn the machine back ON If you wish to change the default function setting please see the section headed Function Setting See Page 6 It is vitally important to adjust the distance between the two Note Guides according to the length of the notes you will be counting Place the notes in the Hopper ensuring that the lower notes within the bundle are inserted firmly into the rear of the feed area The correct Feed Gap setting of the Central Feed Roller assemblies is vitally important to the smooth functioning of the machine After extremely long term usage the urethane components of both the Feed Roller and the Friction Roller may be subject to natural wear Under this condition the Feed Gap may become too wide and as a result Error Codes will be generated and n
15. you want to clear the batch setting and switch to the Continuous Counting Mode press the C key If there is counting number on the counting display the counting number will be first cleared The machine is switched to the Continuous Counting Mode The display will show NC 350A UV 2MG 3D Q kej B GJ GJ GJ GJ 069 CJ GJ GJ ACCUMULATION COUNTING MODE By pressing the ADD key you can select the Accumulation Mode ON or OFF When the machine is in the Accumulation Mode the LED indicator on the ADD key will be on and the counting number will be accumulated on the last counted number The display will show NC 350A UVi2MG 3D J g Ss Su ecu GIG 8 C7 C8 9 After the above customizing steps you can start counting now When there is any error occurs press the START key to continue counting After the counting is finished you can clear the counting number by pressing the C key In Accumulation Counting Mode press the C key first time to clear the last counting number Press it second time to reset the counting display to zero Dustproof cover setting By pressing the C key for five seconds the machine will enter into the Dustproof Cover Setting The display will show NC 350 UVi2MG 3D ig d fae Lo ee GJ 093 C8 G3 09 Ce The dustproof cover will automatic be closed while counting notes and be opened when counting ends By pressing th
Download Pdf Manuals
Related Search