HandyTone 286 User Manual Grandstream Networks
Contents
1. dial 192168000011 For detail HandyTone 286 User Manual Grandstream Networks Inc see 4 2 2 Make a Direct IP Call Dial 86 to check the No Voice Messages or If there are voice messages user can dial voice message Voice Messages Pending 9 and dial pre configured phone number to retrieve voice message Dial 99 to resetthe RESET Dial 9 to confirm the RESET or device Enter MAC address to restore factory default setting For detail see section 8 Dial the invalid Invalid Entry Automatically return to Main Menu number or keypad Notes Once button is pressed it enters voice prompt main menu If the button is pressed again while it is already in the voice prompt menu state it jumps to Direct IP Calling option and dial tone plays in this state All entered digit sequences have known lengths 2 digits for menu option and 12 digits for IP address Once all digits are accumulated it automatically processes them Key entry cannot be deleted but the phone may prompt error once it is detected HandyTone 286 User Manual Grandstream Networks Inc 5 2 Make Phone Calls 5 2 1 Calling phone or extension numbers There are currently two methods to make an extension number call 1 Dial the extension number directly and wait for 5 seconds 2 Dial the numbers directly and press Assuming that use as dial key is selec2. in a controlled LAN environment if possible For users who do not have local TFTP server Grandstream provides a NAT friendly TFTP server on the public Internet for users to download the latest firmware upgrade automatically Please check the Service or Support section of Grandstream s Web site to obtain this TFTP server IP address 595 HandyTone 286 User Manual Grandstream Networks Inc 8 Restore Factory Default Setting Warning Restore the Factory Default Setting will delete all configuration information of the device Step one Find the Mac Address of the device The Mac address of the device is located on the bottom of the device Itis a 12 digit number Step two Encode the Mac address The encode rule is 2 is the first letter on the button 2 so its encoding is 2 A is the second letter on button 2 so its encoding is 22 B is the third letter on button 2 and its encoding is 222 C is the fourth letter on button 2 and its encoding is 2222 For example the Mac address is 000b8200e395 User should encode it as 0002228200333395 Step three Access the voice menu then dial 99 and get the voice prompt RESET Step four Dial in the encode of the Mac address Once the correct encode Mac address dial in the device will reboot automatically and restore the factory default setting 26
3. its capabilities Grandstream s award wining HandyTone 286 is innovative Analog Telephone Adaptor that offers a rich set of functionality and superb sound quality at ultra affordable price They are fully compatible with SIP industry standard and can interoperate with many other SIP compliant devices and software on the market This document is subject to changes without notice The latest electronic version of this user manual can be downloaded from the following location http www grandstream com user_manuals HandyTone pdf Grandstream Networks Inc HandyTone 286 User Manual Grandstream Networks Inc 2 Installation HandyTone 286 is a VoIP Analog Telephone Adaptor designed to work with an ordinary analog telephone The following photo illustrates the appearance of a HandyTone 286 BUTTON RED LED GREEN LED RJ45 RJ11 10M Ethernet 5V 1200mA Telephone HandyTone 286 User Manual Grandstream Networks Inc 3 What is Included in the Package The HandyTone 286 package contains 1 One HandyTone 286 2 One universal power adaptor 3 One Ethernet cable 3 1 Safety Compliances The HandyTone 286 is compliant with various safety standards including FCC CE and C Tick Its power adaptor is compliant with UL standard The HandyTone ATA should only operate with the universal power adaptor provided in the package Warning Please do not attempt to use a different power adaptor Using other power adaptor
4. may damage the HandyTone ATA Caution Changes or modifications to this product not expressly approved by Grandstream or operation of this product in any way other than as detailed by this User Manual could void your manufacturer warranty HandyTone 286 User Manual Grandstream Networks Inc 4 Product Overview 4 1 Key Features e Support SIP 2 0 TCP UDP IP RTP RTCP HTTP ICMP ARP DNS DHCP NTP SNTP TFTP protocols e Support IETF STUN e Interoperable with various 3rd party SIP end user device Proxy Registrar Server and gateway products e Advanced Digital Signal Processing DSP technology to ensure superior audio quality e Advanced and patent pending adaptive jitter buffer control packet delay and loss concealment technology e Support popular vocoders including G 723 1 5 3K 6 3K G 729A B G 711 alaw and u law G 726 40K 32K 24K 16K G 728 and iLBC e Support standard voice features such as Call Waiting Forward in band and out of band DTMF Dial Plans e Support Silence Suppression VAD Voice Activity Detection CNG Comfort Noise Generation Line Echo Cancellation G 168 and AGC Automatic Gain Control e Support DIGEST authentication MD5 MD5 sess e Provide easy configuration through manual operation voice prompt along with phone keypad and Web interface or automated centralized configuration file e Support for Layer 2 802 1Q VLAN 802 1p and Layer 3 QoS ToS DiffServ
5. modes under which the IP phone can operate If DHCP mode is enabled then all the field values for the Static IP mode are not used even though they are still saved in the Flash memory and the IP phone will acquire its IP address from the first DHCP server it discovers on the LAN it attaches to If Static IP mode is selected then the IP address Subnet Mask Default Router IP address DNS Server 1 primary DNS Server 2 secondary fields will need to be configured These fields are reset to zero by default This field contains the URI string or the IP address and port if different from 5060 of the SIP proxy server e g the following are some valid examples sip my voip provider com or sip my company sip server com or 192 168 1 200 5066 15 HandyTone 286 User Manual Grandstream Networks Inc Outbound Proxy SIP User ID SIP User ID is Phone Number SIP Login ID SIP Password This field contains the URI string or the IP address and port if different from 5060 of the outbound proxy If there is no outbound proxy this field SHOULD be left blank If not blank all outgoing requests will be sent to this outbound proxy This field contains the user part of the SIP address for this phone e g if the SIP address is sip my_user_id my_provider com then the SIP User ID is my_user_id Please do NOT include the preceding sip scheme or the host portion of the SIP address in this field If the IP pho
6. 3 Cancel Delayed Call Forward To cancel this Forward dial 93 and get the dial tone then hang up Flash Hook When in conversation this action will switch to the new incoming call if user heard the call waiting sound When in conversation and no incoming call heard this action will switch to a new channel for a new call 5 4 LED Light Pattern Indication Following are the LED light pattern indication RED LED always indicates not normal status DHCP Failed or WAN No Cable flash every 2 seconds if DHCP is configured HandyTone 486 fails to register flash every 2 seconds if SIP server is configured GREEN LED always for normal working status Message Waiting Indication Button flashes every 2 seconds RINGING Button flashes at 1 10 second RINGING INTERVAL Button flashes every second Sie HandyTone 286 User Manual Grandstream Networks Inc 6 Configuration Guide 6 1 Configuring HandyTone IP through Voice Prompt 6 1 1 DHCP Mode Follow section 4 1 with voice menu option 01 to enable HandyTone to use DHCP 6 1 2 STATIC IP Mode Follow section 4 1 with voice menu option 01 to enable HandyTone 286 to use STATIC IP mode then use option 02 03 04 to set up HandyTone s IP Subnet Mask Gateway respectively 6 1 3 TFTP Server Address Follow section 4 1 with voice menu option 06 to configure the IP address of the TFTP server 6 2 Configuring HandyTon
7. 32 ADPCM G728 and iLBC Depending on the product model some of these vocoders may not be provided in standard release A user can configure vocoders in a preference list that will be included with the same preference order in SDP message The first vocoder in this list can be entered by choosing the appropriate option in Choice 1 Similarly the last vocoder in this list can be entered by choosing the appropriate option in Choice 7 This defines the encoding rate for G723 vocoder By default 6 3kbps rate is chosen This defines the size of the iLBC codec frame The default setting is 20ms This defines the iLBC payload type The default setting is 96 This controls the silence suppression VAD feature of G723 and G729 If set to Yes when a silence is detected small quantity of VAD packets instead of audio packets will be sent during the period of no talking If set to No this feature is disabled HandyTone 286 User Manual Grandstream Networks Inc Voice Frames per TX Layer 3 QoS Layer 2 QoS Use DNS SRV User ID is phone number SIP Registration Unregister On Reboot This field contains the number of voice frames to be transmitted in a single packet When setting this value the user should be aware of the requested packet time used in SDP message as a result of configuring this parameter This parameter is associated with the first vocoder in the above vocoder Preference List o
8. MPLS e Remote software upgrades capability via TFTP HandyTone 286 User Manual Grandstream Networks Inc 4 2 Hardware Specification The table below describes the difference among these models Model HandyTone 286 LAN interface 1xRJ45 10Base T Button l LED GREEN amp RED color Universal Input 100 240V AC Switching Output 5VDC 1200mA UL certified Power Adaptor Dimension 65mm W 93mm D 27mm H Weight Operating 32 104 F Temperature 0 40 C Humidity 10 95 non condensing Compliance FCC CE C Tick HandyTone 286 User Manual Grandstream Networks Inc 5 Basic Operations 5 1 Get Familiar with Key Pad and Voice Prompt HandyTone 286 has stored a voice prompt menu for quick browsing and simple configuration To enter this voice prompt menu simple pick up the phone and press the button on the HandyTone 286 or pick up the phone and dial The following table shows how to use the voice prompt menu to configure the device Menu Voice Prompt User s Options Dial to Main Menu Enter a Menu Option Dial to review the configuration of the device or Dial 01 06 or 99 menu option or Dial to return to the Main Menu Dial 01 to configure the DHCP Mode Static IP Mode or Dynamic IP Mode Dial 9 to toggle the selection If user selects Static IP Mode user need configure the all IP addres
9. User Manual Handy Tone 2856 Analog Telephone Adaptor Version 1 00 Grandstream Networks Inc WWW grandstream com Ae HandyTone 286 User Manual Grandstream Networks Inc Table of Contents I WELCOME istesiacceccdecsicccssiccccscccsacsectecccccdccascescsanccccasoadesscsasceccdconscesesooccceasanccneccooceccdconsdoscsoocsccaseas 3 2 SINS TATA TION AEE A E T N E AT 4 3 WHAT IS INCLUDED IN THE PACKAGE 00000000000000000000000 0000000000000 nn nn nn nn nn nn nn nn nennen nennen 5 3 1 SSABETY COMPLIANGES a nl RER Rennen Inne bai hencn elle 5 4 PRODUET OVERVIEW isssccisistccdiasccccciciadecsdacdossceadstecscesccsscnccedsssdoonesscdecees colaccsedceeressceeaess teeacs 6 ALY KEY FEATURES toes 882 80 Klaas ine nen dir else als a Gevae eed iecs a 6 4 2 HARDWARE SPECIFICATION cccccccccccccccssssssesccccceccsseussesceccessessuussecescscsssueususscecessssssuauasescesess 7 5 BASIC OPERATIONS 2 4 5 82 00 8 5 1 GET FAMILIAR WITH KEY PAD AND VOICE PROMPT cccccccccccssessscecccccecssssssscecccccsssusessnsececess 8 5 2 MAKE PHONE CALLS 2 22sec sec ioed occecs socdussvadodcacasuenanivtee bdete a heads suenaaindagegeussuseagsesuedeass ceshee s 10 5 2 1 Calling phone or extension numbers aus sinne diate ta 10 DDD E a E a E E AE A A AAE AA A ae ES EE EE 10 343 EIN E A o RBI I PE E EE EAE E AAE AE E 12 5 4 LED LIGHT PATTERN INDICATION ceeseseesesnsnsnessssssenennnnnnnnnnnnsnnn
10. ated or not If activated by choosing Yes and a STUN server is also specified then the phone will behave according to the STUN client specification Under this mode the embedded STUN client inside the phone will attempt to detect if and what type of firewall NAT it is behind through communication with the specified STUN server If the detected NAT is a Full Cone Restricted Cone or a Port Restricted Cone the phone will attempt to use its mapped public IP address and port in all the SIP and SDP messages it sends out If this field is set to Yes with no specified STUN server then the phone will periodically every 10 seconds or so send a blank UDP packet with no payload data to the SIP server to keep the hole on the NAT open The HT286 sends a UDP package to the SIP server periodically in order to keep the port open on the router This parameter defines the interval time that HT286 send the UDP package The default setting is 20 second NAT IP address used in SIP SDP message Default is blank This is the IP address of the configured tftp server If it is non zero or not blank the IP phone will attempt to retrieve new configuration file or new code image update from the specified tftp server at boot time It will make up to 3 attempts before timeout and then it will start the boot process using the existing code image in the Flash memory If a tftp server is configured and a new code image is retrieved the new down
11. e displayed time will be daylight savings time or not If set to Yes then the displayed time will be 1 hour ahead of normal time If this parameter is set to Yes the From header in outgoing INVITE message will be set to anonymous essentially blocking the Caller ID from displaying If this parameter is set to Yes the configuration update via keypad is disable 6 2 3 Saving the Configuration Changes Once a change is made the user should press the Update button in the Configuration Menu The IP phone will then display the following screen to confirm that the changes have been saved 22 HandyTone 286 User Manual Grandstream Networks Inc Grandstream IP Phone Configuration Update Status Your configuration changes have been saved They will take effect on next reboot Back to Home Page 6 2 4 Rebooting the phone from remotely The administrator of the phone can remotely reboot the phone by pressing the Reboot button at the bottom of the configuration menu Once done the following screen will be displayed to indicate that rebooting is underway Grandstream IP Phone Rebooting Status The IP phone is rebooting now You may relogin by clicking on the link below in 30 seconds Click to relogin At this point the user can relogin to the phone after waiting for about 30 seconds The user is recommended to power cycle HT286 after seeing the above message 6 3 Configurati
12. e with Web Browser HandyTone 200 series ATA has an embedded Web server that will respond to HTTP GET POST requests It also has embedded HTML pages that allow a user to configure the IP phone through a Web browser such as Microsoft s IE and AOL s Netscape 6 2 1 Access the Web Configuration Menu First get the IP address of the HandyTone through section 4 1 with menu option 02 Then access the HandyTone s Web Configuration Menu using the following URI http Phone IP Address where the Phone IP Address is the IP address of the phone Once this request is entered and sent from a Web browser the IP phone will respond with the following login screen HandyTone 286 User Manual Grandstream Networks Inc Welcome to Grandstream IP Phone Password es BB The password is case sensitive and the factory default password is lower case admin 6 2 2 Configuration Menu After the correct password is entered in the login screen the embedded Web server inside the IP phone will respond with the Configuration Menu screen which is explained in details below The definitions for all the configuration parameters in the Configuration Menu are Information Field Password IP Address SIP Server This field shows basic information of the device including the MAC address the model and the software version This contains the password to access the Web Configuration Menu This field is case sensitive There are 2
13. ia the HandyTone ATA s Web configuration interface To configure the TFTP server via voice prompt follow section 4 1 with option 06 once set up the tftp ip address power cycle the ATA the firmware will be fetched once the ATA boot up To configure the TFTP server via the Web configuration interface open up your browser to point at the IP address of the HandyTone ATA Input the admin password to enter the configuration screen From there enter the TFTP server address in the designated field towards the bottom of the configuration screen Once the TFTP server is configured power cycle the HandyTone ATA TFTP checking is only performed during the initial power up If the configured tftp server is found and a new code image is available the HandyTone ATA will attempt to retrieve the new image files by downloading them into the HandyTone ATA s SRAM During this stage the HandyTone ATA s LEDs will blink until the checking downloading process is completed Upon verification of checksum the new code image will then be saved into the Flash If TFTP fails for any reason e g TFTP server is not responding there are no code image files available for upgrade or checksum test fails etc the HandyTone ATA will stop the TFTP process and simply boot using the existing code image in the flash TFTP may take as long as 1 2 minutes over Internet or just 20 seconds if it is performed on a LAN It is generally recommended to conduct TFTP upgrade
14. ing typically an ASCII numeric string If it is not blank then this string will be used as a prefix to the target URI string in the To header field of an INVITE message This parameter allows the user to configure the key to be used as the Send or Dial key Once set to Yes pressing this key will immediately trigger the sending of dialed string collected so far In this case this key is essentially equivalent to the Re Dial key If set to No this key will then be included as part of the dial string to be sent out This parameter defines the local SIP port the IP phone will listen and transmit on The default value is 5060 This parameter defines the local RTP RTCP port pair the IP phone will listen and transmit on It is the base RTP port for channel 0 When configured channel 0 will use this port value for RTP and the port_value 1 for its RTCP channel 1 will use port_value 2 for RTP and port_value 3 for its RTCP The default value is 5004 This parameter when set to Yes will force random generation of both the local SIP and RTP ports This is usually necessary when multiple IP phones are behind the same NAT 20 HandyTone 286 User Manual Grandstream Networks Inc NAT Traversal keep alive interval Use NAT IP TFTP Server SUBSCRIBE for MWI Offhook Auto Dial Enable Call Feature This parameter defines whether the phone NAT traversal mechanism will be activ
15. loaded image will be verified and then saved into the Flash memory Default is NO When set to Yes a SUBSCRIBE for Message Waiting Indication will be sent periodically This parameter allows the user to configure a User ID or extension number to be automatically dialed upon offhook Please note that only the user part of a SIP address needs to be entered here The phone will automatically append the and the host portion of the corresponding SIP address Default is No If set to Yes Call Forwarding amp Do Not Disturb are supported locally 21 HandyTone 286 User Manual Grandstream Networks Inc Disable Call Waiting Send DTMF Send Flash Event NTP server Time Zone Daylight Savings Time Send Anonymous Lock keypad update Default is Not This parameter controls the way DTMF events are transmitted There are 3 ways in audio which means DTMF is combined in audio signal not very reliable with low bit rate codec via RTP RFC2833 or via SIP INFO This parameter allows the user to control whether to send an SIP NOTIFY message indicating the Flash event or just to switch to the voice channel when the user presses the Flash key This parameter defines the URI or IP address of the NTP server which the IP phone will use to display the current date time This parameter controls how the displayed date time will be adjusted according to the specified time zone This parameter controls whether th
16. ne has an assigned PSTN telephone number then this field will be set to Yes Otherwise set it to No If Yes is set a user phone parameter will be attached to the From header in SIP request This field contains the login ID used for SIP authentication Typically this is the account number on an SIP server for this IP phone It can be the same as or different from the above SIP User ID depending on whether a separate account ID is used for authentication This field contains the password used for SIP authentication It is used together with the above SIP Login ID Grandstream HandyTone 286 Configuration MAC Address 00 0B 82 00 C5 BA Product Model HT286 Software Version Program 1 0 5 3 Bootloader 1 0 0 18 HTML 1 0 0 36 VOC 1 0 0 6 Admin Password password to configure this IP phone IP Address C dynamically assigned via DHCP default or PPPoE will attempt PPPoE if DHCP fails and following is non blank PPPoE account ID a PPPoE password Use this DNS server if specified i ma i statically configured as IP Address ise fics foi fico Subnet Mask 55 1255 255 Default Router s2 fica ft fi DNS Server 1 feo2 oe fiza h33 DNS Server 2 feoz oe fize ea SIP Server Sipserver com e g sip mycompany com or IP address 16 HandyTone 286 User Manual Grandstream Networks Inc Outbound Proxy e g proxy myprovider com or IP address if an
17. nnnnnnnnsnensnnnnnnnnnsnsnsnsnnenennnnnn 13 6 CONFIGURATION GUIDE 00000000000000000000000000000000000000000000000000000000000n 00000 n 0000000 n Rn Rn RR nn en 14 6 1 CONFIGURING HANDYTONE IP THROUGH VOICE PROMPT csssesseccccccccsessseescescecessseneusess 14 0 1 DHEP M 9de 2 22 2222 a san NS ERSTER IRRE Hts Sak Me dah ce 2 14 6 12 STATIC TP MOC sided nennen ss esch e a in dba udecesastesbasteventesss tees 14 6 1 3 TETP Server Addressi nsa 2 n an N Seats ta ees E ents 14 6 2 CONFIGURING HANDYTONE WITH WEB BROWSER cscscsccccccccssssessscescccsessesscssceccssseeseneneess 14 6 2 1 ACCESS the Web Configuration Men sah 14 6 2 2 C nfiburaton Menue E EA A sO se EAA eae aa cheats 15 6 2 3 Saving the Configuration Changes anne 22 6 2 4 Rebooting the phone from remotely ccccccccccsccccccssssccecscssscecssssscecsessssecessscaeeessssnesessesenaes 23 6 3 CONFIGURATION THROUGH A CENTRAL SERVER ccccssssssssccccccccssssssscecccsccesssscesesccesssssenensess 23 7 SOFTWARE UPGRADE WITH TFTP 200000000000000000000020200000202000202000200020000020 2000000000000 25 8 RESTORE FACTORY DEFAULT SETTING 00000000000000000000000000000n0002000020000 0000000000000 26 HandyTone 286 User Manual Grandstream Networks Inc 1 Welcome Congratulations on becoming an owner of HandyTone 286 You made an excellent choice and we hope you will enjoy all
18. on through a Central Server Grandstream IP phones can be automatically configured via a central provisioning system called Grandstream Automated Provisioning System GAPS With GAPS a service provider or an enterprise with large deployment of IP phones can easily manage the configuration and service provisioning of individual devices remotely and automatically via a central server GAPS uses enhanced NAT friendly tftp and II HandyTone 286 User Manual Grandstream Networks Inc other communication protocols to communicate with each individual IP phone even if the phone is behind a NAT GAPS must be used to support automated configuration of an IP phone To enable this feature on the phone the user just needs to enter the IP address of GAPS server in the tftp server field of the configuration screen Then power cycle the phone For details on how GAPS works please refer to the documentation of GAPS product 24 HandyTone 286 User Manual Grandstream Networks Inc 7 Software Upgrade with TFTP To upgrade software HandyTone ATAs can be configured with a TFTP server where the new code image is located The TFTP upgrade can work in either static IP or DHCP mode using private or public IP address It is recommended that the TFTP server must have either public IP address or be on the same LAN with the HandyTone ATA There are 2 ways to set up the TFTP server to upgrade the firmware namely through voice menu prompt or v
19. r the actual used payload type negotiated between the 2 conversation parties at run time e g if the first vocoder is configured as G723 and the Voice Frames per TX is set to be 2 then the ptime value in the SDP message of an INVITE request will be 60ms because each G723 voice frame contains 30ms of audio Similarly if this field is set to be 2 and if the first vocoder chosen is G729 or G711 or G726 then the ptime value in the SDP message of an INVITE request will be 20ms If the configured voice frames per TX exceeds the maximum allowed value the phone will use and save the maximum allowed value for the corresponding first vocoder choice The maximum value for PCM is 10 x10ms frames for G726 it is 20 x10ms frames for G723 it is 32 x30ms frames for G729 G728 64 x10ms and 64 x2 5ms frames respectively This field defines the layer 3 QoS parameter which can be the value used for IP Precedence or Diff Serv Default value is 48 This setting includes two fields The 802 1Q VLAN Tag contains the value used for layer 2 VLAN tag Default setting is blank And 802 1p priority value contains the value of the priority value This parameter controls whether the IP phone supports the DNS SRV route function If the HandyTone ATA has an assigned PSTN telephone number then this field will be set to Yes Otherwise set it to No If Yes is set a user phone parameter will be attached to the F
20. rom header in SIP request This parameter controls whether the IP phone needs to send REGISTER messages to the proxy server The default setting is Yes Default is No If set to yes the SIP user will be unregistered on reboot 19 HandyTone 286 User Manual Grandstream Networks Inc Registration Expiration Early Dial Dial Plan Prefix Use as Send Key Local SIP port Local RTP port Use Random Port This parameter allows the user to specify the time frequency in minutes the phone will refresh its registration with the specified registrar The default interval is 60 minutes or 1 hour The maximum interval is 65535 minutes about 45 days This parameter controls whether the phone will attempt to send an early INVITE each time a key is pressed when a user dials a number If set to Yes an INVITE is sent using the dial number collected thus far Otherwise no INVITE is sent until the Re Dial button is pressed or after about 5 seconds have elapsed if the user forgets to press the Re Dial button The Yes option should be used ONLY if there is a SIP proxy configured and the proxy server supports 484 Incomplete Address response Otherwise the call will most likely be rejected by the proxy with a 404 Not Found error Please note that this feature is NOT designed to work with and should NOT be enabled for direct IP to IP calling This value contains the dial plan prefix str
21. rval ko in seconds default 20 seconds UseNATIP 0 Gfspecified this IP address is used in SIP SDP message TETP Server a B fi 53 50 for remote software upgrade and configuration SUBSCRIBE for MWI No do not send SUBSCRIBE for Message Waiting Indication Yes send periodical SUBSCRIBE for Message Waiting Indication Offhook Auto Dial Ze User ID extension to dial automatically when offhook Enable Call Features C No Yes Gf Yes Call Forwarding amp Do Not Disturb are supported locally Disable Call Waiting No Yes Send DTMF in audio C via RTP RFC2833 via SIP INFO DTME Payload Type fior Send Flash Event No C Yes Flash will be sent as a DTMF event if set to Yes EXS Impedance current setting is 600 Ohm North America NTP Server npot sippnnecom URI or IP address Time Zone current setting is GMT 5 00 US Eastern Time NewYork x Daylight Savings Time No C Yes fsetto Yes display time will be 1 hour ahead of normal time Send Anonymous No C Yes caller ID will be blocked if set to Yes Lock keypad update No Yes configuration update via keypad is disabled if set to Yes 2172 HandyTone 286 User Manual Grandstream Networks Inc Preferred Vocoder G723 Rate iLBC frame size iLBC payload type Silence Suppression The BudgeTone IP phone supports up to 7 different vocoder types including G711 ulaw PCMU G711 alaw PCMA G723 G729A B G726
22. s information through menu 02 to 05 If user selects Dynamic IP Mode the device will retrieve all IP address information from DHCP server automatically when user reboots the device Dial 02 to configure the IP address of the device IP Address IP address Such as IP Address XXX XXX XXX XXX Enter 12 digit new IP address if in Static IP Mode for example the address is 192 168 0 10 user should dial 192168000010 Dial 03 to configure the subnet mask Subnet mask subnet mask Enter 12 digit new subnet mask address if in Static IP Mode for example the address is 255 255 255 0 user should dial 255255255000 Dial 04 to configure the default gateway Gateway IP address Enter 12 digit IP address of the default gateway if in Static IP Mode Dial 05 to configure the DNS server DNS Server IP address Enter 12 digit IP address of the DNS server if in Static IP Mode Dial 06 to configure the TFTP server TFTP Server IP address Enter 12 digit IP address of the TFTP server TFTP server is used to update the firmware of the device Dial 47 to make a direct IP call Direct IP Calling When dial 47 user will prompt a dial tone then dial the 12 digit IP address For Example user wants call another SIP phone at 192 168 0 011 User should dial 4T and
23. s specified If the target IP address port is 192 168 1 20 5062 then the dialing convention would be Voice Prompt with option 47 then 192168001020 45062 followed by pressing the key is it is configured as a send key or wait for 5 seconds If the target address is john 192 168 1 100 5062 then the dialing convention would be Voice Prompt with option 47 then 51634262 3192168001100 45062 followed by pressing the key is it is configured as a send key or wait for 5 seconds 5 3 Call Features Following table shows the call features of HandyTone 286 Dial Key Call Features 70 Do not disturb it will give caller busy tone when called This setting will be released when user hangs up the phone 72 Unconditional Call Forward To use this feature dial 72 and get the dial tone Then dial the forward number and hang up 73 Cancel Unconditional Call Forward To cancel Unconditional Call Forward dial 73 and get the dial tone then hang up 90 Busy Call Forward HandyTone 286 User Manual Grandstream Networks Inc To use this feature dial 90 and get the dial tone Then dial the forward number and hang up 9 Cancel Busy Call Forward To cancel Unconditional Call Forward dial 91 and get the dial tone then hang up 92 Delayed Call Forward To use this feature dial 92 and get the dial tone Then dial the forward number and hang up 9
24. ted in web configuration For detail see section 5 2 configure Handytone using web browser Other functions available during the call are call waiting flash call transfer and call forwarding 5 2 2 Direct IP calls Direct IP calling allows two phones to talk to each other in an ad hoc fashion without a SIP proxy VoIP calls can be made between two phones if both HandyTone ATA and other VOIP Devices i e another HandyTone ATA or other IP phone have public IP addresses or both HandyTone ATA and other VOIP Devices i e another HandyTone ATA or other IP phone are on a same LAN using private or public IP addresses or both HandyTone ATA and other VOIP Devices i e another HandyTone ATA or other IP phone can be connected through a router using public or private IP addresses To make a direct IP calling first pick up the analog phone or turn on the speakerphone on the analog phone then access the voice menu prompt by dial or press the button on the HT286 and dials 47 to access the direct IP call menu User will hear a voice prompt Direct IP Calling and a dial tone Then user dials the 12 digit target IP address to make a call If there is a user name part in the target address such as username 192 168 10 123 encode the user name part see the following encoding scheme table followed by 3 encoding for and then followed by the 12 digit target IP address Destination ports can also be specified
25. using 4 encoding for followed by the encoded port number The follow is a table of the encoding scheme for the most commonly used characters 10 HandyTone 286 User Manual Grandstream Networks Inc F 00 01 02 03 04 05 06 07 08 09 0 dot character _ underscore character 2 hyphen character 3 4 column character 21 22 23 31 32 33 41 42 43 51 52 53 61 62 63 71 72 73 74 81 82 83 91 O OO NI AD NM AININ o lt CHAIDLI TASME AT aS HandyTone 286 User Manual Grandstream Networks Inc 92 93 94 NIKI The rule of thumb to remember these encoding is a is the first letter on button 1 so its encoding is 11 b is the 2 letter on button 1 and its encoding is 12 c is the 3 letter on button 1 and its encoding is 13 Likewise d is the first letter on button 2 and its encoding is 21 This pattern and rule applies to all other alphabetic encoding Examples If the target IP address is 192 168 0 160 the dialing convention is Voice Prompt with option 47 then 192168000160 followed by pressing the key is it is configured as a send key or wait for more than 5 seconds In this case the default destination port 5060 is used if no port i
26. y SIP UserID i234 the user part of an SIP address Authenticate ID 1234 canbe identical to or different from SIP User ID Authenticate Password Name GB optional e g John Doe Advanced Options Preferred Vocoder choice 1 PCMU 7 in listed order choice 2 PCMA hd choice 3 G 723 1 r choice 4 G 729A B i choice 5 iLBC X choice 6 l G 726 32 choice 7 G 728 x G723 rate 6 3kbps encoding rate 5 3kbps encoding rate iLBC frame size 20ms C 30ms iLBC payload type je between 96 and 127 default is 98 Silence Suppression No Yes Voice Frames per TX 2 up to 10 20 32 64 for G711 G726 G723 other codecs respectively Layer 3 QoS jae Diff Serv or Precedence value Layer 2 QoS 802 1Q VLANTag 0 2 802 Ippriorityvalue 0 0 7 Use DNS SRV No Yes User ID is phone number No Yes SIP Registration Yes No Unregister On Reboot Yes CNo Register Expiration fo in minutes default 1 hour max 45 days Early Dial No Yes use Yes only if proxy supports 484 response Dial Plan Prefix Faser this prefix string is added to each dialed number No Key Entry Timeout fa in seconds default is 4 seconds Use as Dial Key CNo Yes f setto Yes will function as the Re Dial key local SIP port 5060 default 5060 local RTP port 5004 1024 65535 default 5004 Use random port No Yes NAT Traversal No Yes STUN server is eg URI or IP port keep alive inte
Download Pdf Manuals
Related Search