LK-100S1-Installation Manual
Contents
1. LK 100S1 AUTO DIALER USER S MANUAL FRONT PANEL REAR PANEL 0 8 0 e 0 o 0 ag i o a 5 L6 FARITE 8 OIE 898 i x LK 100S1 O 9 1 PARTS AND FUNCTIONS LCD WINDOW Displays instruction prompts and stored numbers POWER LED INDICATOR Lit when power is supplied REC LED Flashes when record the message and played back message T BUTTON To play back message REC BUTTON record the message MICROPHONE Receives the verbal message KEYPAD Allows programming and entry of telephone numbers KEY OPERATED SWITCH Used to arm or disarm the system BUILT IN SOUNDER Emits recorded verbal message or audible warning beeps FIXING SCREW Fastens the panel 11 PANIC BUTTON To instantly activate dialing FEATURES e Easy to read alpha number LCD Liquid Crystal Display WINDOW virtually makes operation user friendly e Stores up to 8 telephone numbers each 25 digits maximum e Computerized voice chip records your own verbal message for 20 seconds maximum e EEPROM retains memory permanently e Automatically detects the status of the telephone line connected busy shorted or disconnected e With audible warning beeps the system beeps if the system is not ready or when the telephone line is disconnected or shorted e NO Normal Open NC Nor2. Y will be displayed and the until will beep Check the sensor contacts and re arm the system again 8 HOW THE SYSTEM WORKS a when the system is violated AUTO DIALER will start to dial the stored telephone numbers in the sequence of phone 1 phone 2 phone 3 phone 4 phone 5 gt phone 6 phone 7 phone 8 b when a person pick up the telephone which AUTODIALER has dialed he will hear the verbal message played c If a telephone is busy it will be bypassed after three trials d x kK x x ALARM gt gt x gt will be displayed after dialing is completed e To interrupt dialing turn the key to OFF position the action will be stopped immediately To turn on the system again wait for at least 3 seconds 9 SELF DETECTING FUNCTION If the connected telephone line is broken or shorted the until will beep and be displayed to alert the user LINE FAULT will 10 PANIC BUTTON a Turn the key to ON position b Press and keys simultaneously the until will start to dial immediately Note 1 If the exit delay EXIT DEL duration is set other than 0 second i e not instant when the unit is switched ON the green PWR LED flashes fast during the delay after then it flashes slowly and the system is armed 2 If the entering delay IN DEL duration is set other than 0 second i e not instant when alarm is tripped the green PWR LED flashes fast during the dela
3. ess LCD displays PLAY 2 TIMES To set verbal message playback times 3 4 5 press to increase time Q to decrease time d Finally press LCD displays LK100 AUTODIALER and this programming is completed NOTE After x 9 have been entered desired function setting can be jump selected by pressing several times 5 RECORDING AND PLAYING BACK THE VERBAL MESSAGE a To record message Push and hold REC and T buttons simultaneously a beep is heard and REC LED flashes speak to the MIC hole to record the message for shorter than 20 seconds when two beeps will be heard and the REC LED will go off b To play back message Push T button the REC LED flashes and message will be played back 6 ACTIVATING MODES a NC DRY CONTACT MODE Normally b NO DRY CONTACT MODE Normally the sensor contacts are opened the sensor contacts are closed AUTODIALER is activated when the AUTODIALER is activated when the sensor contacts are closed sensor contacts are open BLK RED BLU GRN BLK RED BLU GRN DC12V DC12V INPUT INPUT 7 ARMING THE SYSTEM a Turn the key to ON position b IN DELAY time EXIT DELAY time LK100 AUTODIALER will be displayed sequentially and the system is armed c If the sensor contacts are not normal ZONE NOT READ
4. mal Close two INPUT different activating modes e INSTANT or DELAY MODE selectable e PANIC BUTTON provided for emergency situation or test e Alarm memory displayed after the system has been violated 2 AUTO DIALER PROGRAMMING When programming the key must be turned to OFF position with LK100 AUTODIALER displayed 1 To store telephone numbers memory locations 1 8 a Example store telephone number 1 x 1 initial location telephone end key number number key b Press when finished c To change a stored number repeat above storing procedure 2 To delete a stored number or to bypass a location x 1 initial location end key number key NOTE A deleted numberical order will be bypassed during auto dialing 3 TO REVIEW A STORED NUMBER Simply press 1 18 the stored or telephone number will be displayed on LCD 4 SECURITY SYSTEM PROGRAMMING a Press 9 LCD displays INDELOSEC To set entry delay 0 10 20 30 40 50 60 70 seconds press to increase time 0 to decrease time b Continuously press LCD displays EXIT DELO SEC To set exit delay 0 20 30 40 60 90 120 180 seconds press to increase time Q to decrease time c Continuously pr
5. y after then it flashes slowly and the alarm output is activated To disarm the system switch OFF the unit within the entering delay duration
Download Pdf Manuals
Related Search