View - Microh
Contents
1. MICAROFI LOdra 30 minm 50 mw Green Scanning Laser System USER MANUAL MICRO COdfa 30 NI User Instructions Page 1 Instructions Thank you for purchasing the MICROH CO2RA 30 KH 50 mw Green Laser System For the consideration of your safety and a better understanding of how to use this product please read this users manual carefully and adhere to the guidelines to protect the user and others from the laser emission The 0dfa 30 M Green Laser System utilizes advanced design and uses components manufactured in the USA It features a highly efficient optical system and a very sophisticated drive system The system also features a stand alone function wired remote control with selectable auto or manual methods to choose the available patterns When the auto method is ON it will generate 3D images that will react with sound and change patterns using a real time calculation function When the manual method is ON the user can choose the image patterns manually i e to generate liquid sky effects and tunnel effects All aerial images look best with the use of atmosphere generated by a smoke machine or hazer SPECIFICATIONS Voltage 120VAC e AC Frequency 60 Hz Power consumption 100Watts Fuse 2A 250V e Laser Diode USA Made semiconductor unit 50 mw output Resistance gt 2 MQ Control Signal NMICROH Codra 30 nini remote control Pattern Trigger Auto Sound activated e Strobe Flash Yes Beam2. 5 pin XLR input connector on the back of the laser The laser may now be plugged into an appropriate AC power source Do not plug in or remove the remote connector while the laser is powered ON Install the laser system in a well ventilated area make certain none of the vents are blocked on the laser Only replace the fuse with the same type and rating 2A 250V MICRO COdra 30 NI User Instructions Page 3 OPERATING INSTRUCTIONS WARNING ONLY A 5 pin XLR to XLR cable can be used to extend the wired remote cable The wiring is of pin to pin type Use the wired remote cable and connect the 5 pin XLR to the laser controller input Multiple lasers can be used with one remote control To do this a 5 pin XLR XLR cable is required Simply connect the next laser from the output of the first laser system and so on until they are all connected A maximum of 8 laser units can be daisy chained with one remote control Every time the unit is powered on it will undergo a reset and home The laser system will be ready for use once this reset is complete Do not shake the laser while it is in operation APPENDIX WIRED REMOTE INSTRUCTIONS The 4 afd4 30 nix Laser System Wired Remote control is only intended to be used with the d Ad 30 nin Laser System Multiple units may be connected together and the patterns can be accessed from the single remote The laser system may also be used separately to change patterns manually or by s
3. Angle Wide Angle e Size 13 x 4 5 conical Net Weight 6 Ibs MICRO COdrfa 30 NI User Instructions Page 2 SAFETY INSTRUCTIONS Only qualified service technicians are authorized to do repairs on this unit There are no user serviceable parts inside this unit Correct primary voltages must be used 120VAC Do not block any of the ventilation of this laser system while it is in operation Do not use or store any flammable or explosive products i e pyrotechnics near this laser equipment Do not place your hand directly in front of the laser beam Minimum distance between laser output and any object is 1 meter To avoid serious eye injury do not look directly into the laser beam Point the laser effect in a safe manner towards the desired location PACKAGE CONTENTS e LOdnda 30 nin Green Laser Light cOBRA 30 nix Nired Remote Control e AC Power cable 120VAC User manual INSTALLATION INSTRUCTIONS This laser product is suitable for indoor use only The normal operating temperatures ambient must be below 35C A qualified technician should be familiar with all safety aspects and user functions before installing and using this product Safe hanging procedures should be followed Inspect all the equipment and verify that there has not been any damaged caused by transportation e Connect the AC power plug into the connector on the back of the laser Connect the wired remote cable into the
4. of the LED display Press the ENTER button to confirm the change SHOW PATTERN AUTO MANUAL BANK DOWN PATTERN BLACKOUT SELECT ENTER d LI LI LOdrd 30 MICROFI
5. ound activated control There are 5 buttons on this controller AUTO MANUAL PAGE DOWN BLACKOUT PATTERN SELECT ENTER SHOW PATTERN Numerical LED display Make certain the wired remote is connected to the laser system and there is AC power connected to the laser When the power is ON H will be shown on the LED display then the laser will react by music via the internal microphone and start drawing aerial images Press the AUTO MANUAL button to select between the AUTO or MANUAL function MNICROFH COdfa 30 NI User Instructions Page 4 Press the AUTO MANUAL button to select MANUAL mode 0 will be shown on the LED display the MANUAL function is engaged Then press the PATTERN SELECT key to choose patterns To select a different pattern use the PATTERN SELECT button and scroll through the available built in patterns The LED display will flash with the corresponding pattern number Press the ENTER button to select the new pattern the LED display will stop flashing the pattern number and the new pattern will be displayed from the laser e When a pattern is running using the BLACKOUT button will black out the laser no laser image will be displayed There are two available banks of patterns Press the BANK DOWN button to select the next available bank of patterns Once the BANK DOWN button has been pressed a red dot will be displayed on the bottom right corner
Download Pdf Manuals
Related Search