EPC-12 Configuration Software User Manual
Contents
1. Device name zone EPL 12 zone EPC 12 5 Main page Instantaneous Values When you start to use the program after the connection with the device has been established Instantaneous Values page will open automatically The definition of the device that you are currently connected to device ID version serial number date time tariff information of the device log record number that the device will do next and alarm information can be read on this screen Additionally you can read counter values with tariffs and as totals with unit information You can refresh the screen manually by clicking on the Refresh button or you can make the displayed information on the screen refresh automatically every 10 seconds by clicking on the Auto Refresh option When you select Auto Refresh button the menus will appear passive until display refreshes once After the refresh occurs once the menus will become active When you select the Refresh button you will not be allowed to access the menus until the display refreshes Attention The most appropriate screen resolution for the program is 1024x768 pixels If the screen resolution is not set to the appropriate value some values may not be displayed out of page EPC 12 Configuration Software User Manual al EPC Configuration Software Instantaneous values Device definitions Settings Counter values p 3 zone EPC 12 v Device name 3 zone EPC 12 DevicelD Version Se2. When you change these settings while you are connected to your device via Modbus Serial the settings you committed in the Add Edit device window will be changed according to EPC 12 RS 485 settings by the program and the connection will be automatically reestablished Information LD Connection lost Connection will be reestablished according to EPC 12 R5 485 settings Tamam If you are connected to your EPC 12 device via Modbus TCP you will lose your connection when you change the Baud Rate and Parity settings in RS 485 parameters and you will be asked to enter your Modbus TCP Gateway settings according to EPC 12 RS 485 settings When you enter your Modbus Gateway settings according to EPC 12 device and click on OK button the connection will be reestablished information JJ Connection lost Please update the Modbus TCP geteway settings Tamam 6 1 2 General Settings You can set a new password activate deactivate an existing password change log recording period activate deactivate DST Daylight Savings Time or synchronize the device date time and your computer date time by clicking on General Settings under Device Configurations menu In order to prevent you from forgetting the changes that are committed in this menu changed settings will be marked red after each change Apply button will not be clickable unless you make any changes a General settings 3 zone EPC 12 Password 0 Password activ
3. m 0e 1m4mteo00 J 0 _27 Counter2 m OB iemarm22000 J 0 28 Counters tm B _23 Counter 4 tm B ___ p _ o _30 CounteS Jm 08 ___ ___ p _o_ 31 3 zone Counter __ m3 __08 _ ____ ____ ___ y O _32 EPC 12 Counter NASA A E IS E Counters Jm 08 J S ___p _ o 34 Counte9 mf _08 _ ___ __ __ po 35 Countert0 ma os S O _36_ Counterti tm B S o 37 Counter12 tm B ___ ___ _ O Factory Settings User name admin Password 1234
4. Admin can change the authorization properties of users from the User operations menu Users can t change their authorization properties al User operations Authorization Authorization List Admin User 1 Add edit device RS 485 parameters General settings Unit and multiplier settings Tariff settings Write delete index User operations Add edit Instantaneous values dd ld Y Y E E El aaa aa MOTA Cancel 7 Counter Values Menu 7 1 Instantaneous Values You can monitor counter indexes with tariffs and total counter indexes of your EPC 12 device at that time with unit information by clicking on the instantaneous values option under Counter Values menu 7 2 Log Reading You can read past counter indexes of your EPC 12 device with date and tariff information by clicking on Log reading option under Counter Values menu In order to be able to read past log records a starting date time and an ending date time must be entered After the starting and ending time and date information is entered and Get report button is clicked on reports will start coming in When log reading is finished an informative message indicating that the log reading is finished will be displayed You can read Tariff consumption and Total difference consumption the difference between ending and starting dates on the bottom lines of the log records table You can filter with regard to tariff by dragging the Tariff column to the are whe
5. EPC 12 Configuration Software User Manual apa fe EPC12 1 General PUTOS STE 1 2 Installation OF PrOgrAM o commomenicormnmmcnrrmmmmcrrress 1 Select Installation Folder 3 Entera 10 PrO Miri E 2 A DaS IICTIRTACAS MARL oionn 2 Ns dd MA 2 4 2 DISCOS somos RA NARROS IEA 3 The installer will install EPC12 to the following folder A A A A An 3 4 4 Connecting To A Previously Saved Device Deleting A Device To install in this folder click Next To install to a different folder enter it below or click Browse and Editing Device Connection SettingS coccccccccccnnccononocccncnnnnnnanononons 3 5 Main page Instantaneous Valle licor rin 3 Folder eee eee eee ee ee ee eee eee eee eee ee ee ee eee eee ee ee eee eee eee Ass 6 1 1 RS 485 RaPaniSters nccccrcorcvnneanerssunsssenneesmeamnnvanersencennmennnens 4 6 1 2 General Settings 4 m eee eee eee eee eee eee eee ee eee eee eee eee eee eee ee O MOS iaa 4 Progam Fles EnteaEPCIA O 6 1 Device Configurations 4 a abi Tenses 61 3 Unit and MUIIDIEFPSSTHAGS crcrserecerncrorerscnrecmnceeserenerssnenes 4 614 Tar AAA 4 Install EPC12 for yourself or for anyone who uses this computer 6 1 5 Write Delete MUS accionar 5 62 Froen Scio Sanr ARONA 5 Everyone DRAE E E MM 5 BS User Donna 5 O Just me obe DU o oE g e N A A A E AE ADA EA 5 Qi ANTON sentena prey soonenecaenmnome eo NERNET RS ro miexenans 5 Cancel Back Next gt 7 Gunter SS MS morra ec 5 il TA MATEUS VAIS
6. This required field can t be left blank Login Language Dil English User name Password 1 0 11 1405 Version Login Lancel re User name is incorrect Login Language Dil English User name admin Password 1 0 11 1405 Version Login Cancel ie The password is wrong 4 Device Definitions Menu 4 1 Add edit device In order for you to be able to configure device settings and to monitor your meters by connecting to your device after you logged in to the program with your User name and Password you must enter the connection settings If you are using the program for the first time or there isn t a device that you previously defined Add device screen will be opened automatically You can enter a name for your device in the Device name field EPC 12 on 1st floor for example Afterwards you can select the type of your device You can select the Connection Type as Modbus TCP or Modbus Serial The screen will change according to this choice When you select the connection type as Modbus TCP click on Connect button after you entered IP address TCP port no NAD Device address Poll delay and Time out information of your device When you select the connection type as Modbus Serial click on Connect button after you entered Com port Baud rate Parity NAD Device address Poll delay and Time out information of your device After you cl
7. ater select any tariff set you want without going into separate tariff settings by checking the Use the saved tariff set checkbox 6 1 5 Write Delete Index You can delete counter indexes of your EPC 12 device or write new ones on the Write Delete Index window under Device Configurations menu In order to change index values Counter Set menu on the EPC 12 device has to set as Enable Otherwise This feature is deactivated on the device message will be displayed when you try to change index values You can change the index values only by entering values to counters with tariffs Total counters can only be deleted reset to zero If you didn t set any tariff T1 tariff will be active and you will be able to change index values by writing to counter with T1 tariff When you want to delete counters you can do it by clicking either Reset all checkbox for all counters or separate Reset checkboxes for separate counter and click on Apply button For security purposes you will be asked if you want to reset the counters and this message will have a wait time of 5 seconds If you answer yes to Are you sure you want to reset the counters question counters will be reset In order to prevent you from forgetting the changes that are committed in this menu changed settings will be marked red after each change GB Wiite delete index 1 zone EPC 12 al l Counters Tariff 1 Tariff 2 Tariff 8 T
8. ction which you defined previously Add device screen will not be displayed automatically after you entered your User name and Password In order to connect to a device that you defined previously you can connect to that device by selecting your device and clicking on Connect button as shown below If you want to connect to a device that you didn t define beforehand you can add a new device in the Add Edit Device screen under Device definitions menu and connect to it If you want to delete a device that you defined previously you must select itas shown below and click on the delete button X icon You will be asked to confirm the deletion before the defined device is deleted If you want to change the connection settings of a device that you previously defined you must select it as shown below and click on the edit button Pen icon You can change settings on the appearing window If you want to connect to a device while you are already connected to another device you must end your current connection by clicking on Disconnect option under Device definitions menu Afterwards you can connect to a new device after you clicked on Add Edit device button again and created a new device or if there are connections that you defined beforehand you can select these devices and connect to them by clicking on Connect button as shown below al EPC Configuration Software Counter values Settings Device definitions 3 zone EPC 12 Connect
9. e Log recording period min 1 Automatic Daylight Saving Time switch Pon 7223 2012 12 43 31 PM Device time 7223 2012 12 43 24 PM C Synchronize to PC time Apply Cancel When you change any of the settings and click on Apply button you will be asked to confirm the changes that you committed The committed changes will not be in effect if you don t answer the confirmation with Yes 6 1 3 Unit and Multiplier Settings You can set multipliers and denominators for the pulses that come to EPC 12 inputs and define units for the counters that you are reading by clicking on Unit and multiplier settings under Device Configurations menu In order to prevent you from forgetting the changes that are committed in this menu changed settings will be marked red after each change 3 zone EPC 12 x al Unit and multiplier settings Counters Multiplier Denominator Unit Counter 1 1 1 VAh Counter 2 1 2 Wh Counter 3 2 1 kWh Counter 4 1 3 Vath Counter 5 3 1 k Ah Counter 6 1 4 kVAh Counter 7 tf 1 Imwh Counter 8 65535 1J Counter 9 1 65535 cal Counter 10 10 1 m3 Counter 11 100 1 cm ZA Unless E Uniess S Wh V amp h Appl Vath kwh 6 1 4 Tariff Settings Holiday Saturday Sunday and Weekday tariff can be programmed 8 for each under tariff settings You can name the tariffs that you entered with numbers from 1 to 8 You can select any tariff for example T1 tariff more than once provided that it doesn t conflict with another
10. el The program will start to be installed EPC 12 Configuration Software User Manual ie EPC1 Installation Complete EPC12 has been successtully installed Click Close to exit Please use Windows Update to check for any critical updates to the NET Framework Close When the installation is complete click on Close button to exit setup 3 Entering to Program You can start the program by double clicking on the EPC 12 Configuration software shortcut or by selecting it from the Start menu When you start the program for the first time Login screen will appear and you will be asked to enter your User name and Password a Login Language Dil English User name Password 1 0 11 1405 Version Login Cancel Additionally you can select your language on this window After you selected your Language and entered your User name Password information click on Login button Note If you are starting the program for the first time enter admin as the User name and 1234 as the Password You can change your password from the User Operations menu under Settings menu If you don t enter a User name and Password or you enter the wrong ones a warning message will appear as displayed in the screen shot below Login to the program by entering your User name and Password correctly Login Language Dil ES English User name Password 1 0 11 1405 Version Login Cancel a
11. ick on Connect button entered connection settings that you entered will be saved to the system automatically This ensures that you will be able to connect to your device by selecting it according to its name from a list and you will not be asked to enter any settings when you close and re open the program EPC 12 Configuration Software User Manual aH Add device x Device name z Device model EPC 12 Connection type Modbus TCF s IP gt TCP port number 502 NAD Poll delay mz 50 i Time out rng 1000 Connect A Cancel oH Add device x Device name Device model EPC 12 Connection type Modbus S eral COM port Comm Baud rate 1200 Parity Hone Data bits 8 Stop bits 1 MAD z Poll delay m 250 Time out ris 1000 Connect Cancel When the connection is successfully established an information message including the ID version and serial no information of the device will be displayed Information If the device you re trying to connect is not EPC 12 a warning message will be displayed as below Warning 4 2 Disconnect Disconnect option under the Device definitions menu is used to end the currently ongoing connection 4 3 Close Close option under the Device definitions menu is used to exit from the program 4 4 Connecting To A Previously Saved Device Deleting A Device and Editing Device Connection Settings If there is a device conne
12. otal Reset Counter 1 4294967295 Wh 4234967295 Wh 4294967295 Wh 0 Wh O Counter 2 0 VAh 0 v h 0 VAh 0 V h E Counter 3 0 Vath 0 V rh 0 Vash 0 Vath E Counter 4 100 kWh 1000 kWh 2555 kWh 0 kwh O Counter 6 0 kVAh 0 kVAh 0 kV4h 0 kY h O Counter 7 D ImwWh 0 Imwh 0 ImwWwh 0 Imwh O Counter 8 0J oJ oJ oJ O Counter 9 0 cal 0 cal 0 cal 0 cal O Counter 10 0 m3 0 m3 0 m3 0 m3 O Counter 11 0 cm 0 cm 0 cm 0 cm E Counter 12 0 NAN 0 NAN 0 NAN 0 NAN go C Reset all 6 2 Program Settings 6 2 1 Change Language Although you can select the program language at the start of the program you can also select it from Program settings menu 6 3 User Operations 6 3 1 Add Edit You can add new users change password user name status of users and delete users by selecting Add edit option under User operations menu Program will have only one admin Admin can add a new user edit a current user and change the authorization properties of users Users can use the program according to the authorization properties which are given to them by the admin Admin can t change its own user name but can change its password 2 User operations Add edit x admin New User name Delete Password Status Active Cance When you add a new user you will be asked if you want to change the authorization properties for the new user and if you want you will be able to set authorization properties for the new user 6 3 2 Authorization
13. re it says Drag a column here to group by this column Additionally you can save this table to your PC by clicking on the CSV icon 8 Check In Out A simple example on how you can monitor check in check out operations using log reading feature of your device is given below You can create a table as displayed below by learning the consumed energy amount according to starting and ending date and time This way you can keep track of the check in check out operations of your facility EPC 12 Configuration Software User Manual A B G D E E G H I Counters Location Unit Unit Price Check in Date Check out Date Used Energy Payment l Name and Time and Time 2 _ UE Counters c8 wh 1 J 5 Counters D2 Wh Ot E Countes D3 Wh Ot 7 1 zone Counters D4 Wh e S O _8 EPC 12 Counter 1 room Wh 1 S e S O _ Countea 2 room wh tf ___ p _o_ 10 ATE M EE A o E E E E Counterto Wh Tt 12 Countert1 Wh 14 _ _ po 13 Countert2 Wa 4 po 14 Counter Je 11 170121900 o S D E Counter2 Lf 114 160412 20 00 J 0 16 Counte3 J Lt E Counter Je OO poa 18 Counters tl tt __ ___ _0_ 19 2 zone Counters J 6e 14 _ ___p S 0 20 EPC12 Counter J6 14 S O E ee NA ESAS AN A AA E Counter A PASA NA a ee _23 CountertO EY tt po 24 Countertt EY tt po 25 Countef2 tt 14 S S D _26 Counter
14. rial No EPC 12 01 01 D201011100000005 Date Time 7223 2012 12 45 27 PM Tariff Tariff Next record number to be written 13656 Refresh Alarm Normal D Auto Refresh Counters Total Counter 2 0 VAh Counter 3 0 VAth Counter 4 0 kWh Counter 5 O kVAh Counter 6 O kv h Counter 7 0 Imiwh Counter 8 OJ Counter 9 0 cal Counter 10 O m3 Counter 11 0 cm Counter 12 O NAN 6 Settings Menu 6 1 Device Configurations You can adjust the settings for your EPC 12 device by selecting Device Configurations from the Settings menu RS 485 Parameters General Settings Unit and Multiplier Settings Tariff Settings Write Delete Index Settings can be found under Device Configurations menu 6 1 1 RS 485 Parameters RS 485 parameters are necessary settings for the communication between your EPC 12 device and a PC You can set these parameters from the menu settings on the EPC 12 device or by using EPC 12 Configuration Software When you select RS 485 Parameters from Device Configurations a screen will be displayed as below When you change the RS 485 Parameters Apply button will not be clickable until you check the box next to Settings you have committed here will change the settings on the device Please confirm ad RS 485 parameters 1 zone EPC 12 Baud rate 3600 Parity None zi NAD 1 Settings you have committed here will change the settings on the device 1 zone EPC 12 Please confirm Cancel
15. rra ONES 5 7 2 Log De FIG A Pr A 5 Select the folder that you want to install the program by clicking on the 8 CHEK IN OUt ssseessesseeerersereerrensresrtensrerntenseernrasnennneenseeserenresnneenrneneeenes 5 Browse button and click on Next button Program will be installed to Program Files Entes EPC12 folder by default 1 General Purpose EPC 12 Configuration Software is designed to configure EPC 12 via a PC to monitor the counter values remotely to write values into counters remotely and to read EPC 12 log records i EPC12 Confirm Installation 2 Installation of Program Run the setup exe file in the EPC 12 Setup folder on the CD which came with the EPC 12 that you bought The installer is ready to install EPC12 on your computer Click Next to start the installation Note Turn Windows Updates on for NET Framework updates Welcome to the EPC12 Setup Wizard The installer will guide you through the steps required to install EPC12 on pour computer Click on Next button for the installation to start i EPC12 Installing EPC12 EPC12 is being installed WARNING This computer program is protected by copyright law and international treaties Unauthorized duplication or distribution of this program or any portion of it may result in severe civil or criminal penalties and will be prosecuted to the maximum extent possible under the laws Please wait On the appearing screen click on Next button Canc
16. tariff s time slot If there is a previously set time slot you will not be allowed to create another tariff in this set time slot If you don t create any tariff the device will save the incoming pulses to T1 tariff Tariffs which are set as holiday tariffs are prioritized over Saturday Sunday and weekday tariffs If the 5th of June is set as holiday tariff and this tariff is setas 17 T7 tariff will be active when June 5th comes If there is a tariff which is set as Saturday Sunday or weekday in this time slot that tariff will be deactivated for this day You can delete a previously set tariff by selecting it and clicking on the X button on the Tariff settings window EPC 12 Configuration Software User Manual a Tariff settings 3 zone EPC 12 x Use the saved tariff set Device tariff type Date 10n Weekdays 23 07 2012 C Saturday Cl Sunday Cl Holiday 23 07 2012 Tl amp Tariff set detail Device tariff type Tari Start year End ye Staitmonth End m Start day End day Start hour Start minute Endhour End minute On Weekdays 11 14 15 19 Saturday T2 14 15 19 Sunday T3 14 15 10 Define tariff on the device After you entered your tariff settings you can click on Define tariff on the device button to activate these tariff settings When you click on Define tariff on the device button you will be asked if you want to save the tariff set When you save the tariff set you entered you can l
Download Pdf Manuals
Related Search