Application Note: TIU
Contents
1. NOTE Switch 1 and 3 must be used together Unit 1 Centrepoint CentreParkRd ONR nina Hl reland SEE mG ees E E E E Rev Date EO Description of Change By Date 25July 2000 ON 1 0 27 04 00 Initial Release AB Doc 4 3 2 1 1 1 25 07 00 Additional link to pin 5 added AB Title Cable Dwg TIU TelemecaniqueTSX37Series PLC DrawnBy Andrew Brailsford Rev 1 1 SW1 Current EO Sheet 3 of 32. orascory Ready Horner Electric APG 640 North Sherman Drive Indianapolis Indiana Phone 1 317 916 4274 Fax 1 317 916 4287 www heapg com Tss 3722 V0 Terminal Fort E UMI TEL WA LIME Fj mast Ewen data Bleep or slaves Server address ADO Number of addresses curent loop ies A tauttidren l Point tepeint Transmission speed 3600 bitsis oF Wait time M Default Data fS bite f abits p Parity Even e Odd Hemen 7 i a adime I Gate Garter or OFFLINE SYS MODIFI Figure 1 PLC7 Screen Capture Slave Configuration Menu Page2 of 3 Horner APG Europe Unit 1 Centrepoint Centrepark Rd Cork Ireland Phone 353 21 4321 266 Fax 353 21 4321 826 www horner apg com CONNECTING AN OPERATOR STATION to a Telemecanique TSX37 Micro PLC TSX Micro TER port TIU Twisted Pair 8 Way Micro Din connector rear view x 5V TX 485 422 TX 485 422 RX 485 422 RX 485 422 TX RS232_ 6 RX RS232 _ _ 8 TX4 20mA 9 TIU100 TIU110 TSX Micro TER port Twisted Pair 8 Way Micro Din TIU WA connector rear view TX 485 422 1 TX 485 422 _ 2 TIUO50 TIU200 TIU101 TIU102 Configuration Bank Cable Screened Twisted Pair Beldon 9502 Use one pair for Data Swith ON OFF Second pair for OV Pull up No Pull up 120 termination No termination Pull down No Pull down Reserved for future use
3. HORNER rp APP0393 001 Application Note TIU Unitelway 1 0 INTRODUCTION This application note is designed to assist the user in configuring the Operator Stations HE500TIU050 10X 11X 20X with the Group Schneider Modicon TSX Micro as a Unitelway V1 1 Client Master It is not intended as a User manual for either product range for more information on the features and use of the equipment please see the individual User s manuals 2 0 PROTOCOL FILE NAME The protocol files are saved in three different files choose the protocol for the required model from the following list Cbreeze will only desplay the correct one once the model has been chosen HE500TIU050 Unitel_R 0xx HE500TIU1xx Unitel R 1xx HE500TIU2xx Unitel R 2xx The the TIU firmware revision 3 0 CONFIGURING THE OPERATOR STATION The initial screen upon power up displays various information about the Operator Station including what firmware version is loaded and what protocol If the Unitelway protocol is not loaded select the Automated Equipment in the Communication Settings from the Configure menu in CBREEZE software Select the appropriate Manufacturer and the appropriate Remote Equipment Model Then from the File menu select Update Protocol the appropriate file name will appear in the file name field The programmer may need to point to the correct folder name location If further information is required see the manual or CBREEZE help on updat
4. e change protocol The Horner APG Unitelway V1 1 Protocol supports read and write of e Internal Words e Internal Bits e System Words e System Bits 3 1 SERIAL PORT FORMAT The PLC defaults to using 9600 baud 8 data bits one stop bit and Odd parity The connections are via the 2 Wire RS485 TER port 4 0 PLC CONFIGURATION The PLC can be configured as a Client master or a Server Slave When connecting to a TIU it must be configured as a Server As well as the PLC mode the Server Address must also be set Both these are configure by the PL7 programming software Open the Application Browser click on Hardware Configuration when a picture of the PLC is visible click on the block labeled Comm Then make sure that the Type box is set to Slave and the Server address is set to match the node address in CBREEZE see Figure 1 a PLC7 screen capture Horner Electric APG Page 1 of 3 Horner APG Europe 640 North Sherman Drive Unit 1 Centrepoint Indianapolis Indiana Centrepark Rd Cork Ireland Phone 1 317 916 4274 Phone 353 21 4321 266 Fax 1 317 916 4287 Fax 353 21 4321 826 www heapg com www horner apg com ul PL Micro lt Untithed gt Configuration HORNE R APG APP0393 001 Application Note TIU Unitelway PLC Debug Options Window 2 xan Designation PROCESSOR 3722 ff Hardware Configuration Software Configuration Program Animation T ables Configuration wo
Download Pdf Manuals
Related Search