Home

Intelimax User Manual

1. Click Firmware Upgrade button and select firmware file And open the file the uploading screen appears Do not remove Intelimax s cable or turn off the power until upgrade finishing Intelimax User Manual SMS Commands IP modes The Intelimax can be used to send and receive SMS messages through standard SMS AT commands with an internal buffer of 100 messages In addition to this the Intelimax supports a number of custom SMS messages for which can be used to check and modify some settings remotely Following SMS commands can be used to change the APN ID Password Authentication and even rebooting Intelimax Also after changing the APN ID Password Authentication Intelimax will send a confirmation SMS after applying the change Change APN e g telstra extranet SMS Syntax INTELIMAX PARK APN telstra extranet Response APN set as lt APN gt Change Username Password and Authentication e g Username maxonQmaxon com au Password maxon Authentication chap SMS Syntax INTELIMAX PARK AUTH maxon maxon com au maxon chap Response IP lt P IP IP IP gt APN lt APN gt ID lt ID gt PW lt PW gt Auth lt PAP CHAP BOTH gt Re g lt 0 1 gt Sig lt CSQ gt Check Settings and IP address SMS Syntax INTELIMAX PARK WANIP Response P lt IP IP IP IP gt APN lt APN gt ID lt ID gt PW lt PW gt Auth lt PAP CHAP BOTH gt Re g lt 0 1 gt Sig lt CSQ gt Reboot Intelim
2. 3 packets transmitted 3 packets received z packet loss round trip min avg max 433 8 446 3 457 6 ms INTELIMAX it The command uptime shows you the connection time as shown in the screen shot below ja Telnet 123 209 44 193 none gt login admin Password 2 for help setup at exit uptime Aday Ghour 48min 3 sec INTELIMA m 75 Use defconiig to clear all the setting which will configure the modem to factory default state E ja Telnet 123 209 44 193 none gt login admin Password sh 1 6 help or V for help INTELIMAAX stat setup at ping upt ime reboot defconfig exit INTELIMAX it defconfig All Config will be init Continuel y N y Now nuram clear all Success Now nuram save to Device Success INTELIMAR _ Intelimax can be power rebooted using the reboot command after logging into the Intelimax remotely Telnet 123 209 44 193 none gt login admin Password sh 1 8 for help it 7 setup at upt ime ig exit INTELIMAX reboot Intelimax User Manual Extended Intelimax Specific AT Command Set IP Stack Modes Device Information ATI Manufacturer Maxon Australia Pty Ltd Model Number MA 2015 Product Name Intelimax F W Revision 0 0 0 201201130929 H W Version 1 0 Module F W Revision 11 810 09 05 00 LAI 50506 LAC 4eeb CelllD OOcb 3b3 IMEI 3542830401 17446 OK AT CGMI Maxon
3. Maxon recommends using the GUI connected via a TCP IP connection in order to Utilise all the configuration settings When connecting to the Intelimax using the GUI when the modem is in serial modem mode there will be very limited functionality After connecting to the modem using the GUI users can configure WAN settings Scheduler IP Stack SNMP Dynamic DNS and Admin settings Intelimax User Manual Connecting to the Intelimax TCP IP Connection Recommended Using the TCP IP connection option allows users to connect to the modem via an IP connection The modem must be connected to via TCP to perform firmware upgrades Local Connection To use this feature locally you must follow the following steps 1 2 Plug in modem RJ45 power serial cable then mini USB cable in this order Install USB LAN drivers which can be downloaded from http www maxon com au product supports drivers and manuals html Set a static IP address to the modem Once the drivers are installed you will have to set a static IP on the Intelimax network connection as the Intelimax does not support DHCP A Local Area Connection 5 p _ Unidentified network T USB Ethernet RNDIS Gadget The default IP for the Intelimax is 192 168 10 1 set your IP within this range Eg 192 168 10 50 Open the GUI to the modem after modem has booted 1 2 minutes The default settings are Address 192 168 10 1 Intelimax LAN IP address Port 10918 ID adm
4. IP Stack Manual mode manual connect IP Serial modem mode for CSD or when end device controls connection Intelimax User Manual Apply all the settings and reboot program maxon lock Once the commands have been received by the modem it will display Modem will reboot now and the call will be dropped as the modem reboots 8 me COM58 PuTTY Once the modem reboots approximately 2 minutes if a public dynamic IP address has been used it can be found using the following SMS to the phone number not data number of the SIM in the modem INTELIMAX PARK WANIP Intelimax User Manual LED Functionality Description _ Signal Strength T Power LED Data LED IP STACK IDLE SIGNAL gt 84dBm 1 sec off 1 sec off 1 sec off 1 sec off 1 sec off 1 sec off 1 sec off ONLINE 1 sec off 1 sec off 1 sec off 1 sec off 1 sec off SERIAL MODE SIGNAL lt 96dBm 1 sec on 1 sec on ONLINE 1 sec off 1 sec off Intelimax User Manual Modem Debugging Local Connection Checking In order to verify that the modem is operating correctly locally follow the below steps 1 Check that modem Power LED is either solid on or mostly on The better the signal strength the more time the Power LED will stay on 2 In serial modem mode a Connect to modem with GUI via USB interface and check the registration and signal strength of the modem The status page will snow whether the modem is currently registered as well as
5. Using this method the modem will be powered up for a certain duration then power itself down for another period of time and the cycle repeats itself To setup scheduler by duration enter for how long you wish the modem to stay powered up and enter power cycle duration The power down will be calculated by the modem In the below example the modem will stay powered for 5 min power down for 25 min and the cycle is repeated Range 0 60 minutes Modem Configuration Status wan Scheduler Serial IP Stack Emulation DDNS Admin System Scheduler RS232 Control F Power Off PowerUp 5 min poner Down 25 min Power Cydein 30 Intelimax User Manual Serial Configuration The Serial configuration page is used to setup modem serial settings such as baud rate serial messages and SMS on boot Modem Configuration Status WAN Scheduler Serial IP Stack Emulation DDNS Admin System Serial Bootup Message Communication Baudrate Data bit Parity Stop bit Flow Control Modem Config Serial Port Setup Serial port setup includes the following Baud rate the modem supports 1200 2400 4800 9600 19200 38400 57600 and 115200 Data Bit 7Bit or 8bit Stop bit 1bit or 2bit Flow Control None Software or Hardware amp D S0 amp C Echo and Q Intelimax User Manual Serial port speed setup should be set to match host connected via serial p
6. Band Backof pisabie w Periodic Reset Disable v Hours IP Stack Auto z telstra internet Disable v Pin Code LCP Echo Failure 10 v Counts EGSM 900 V GSM DCS 9 v 700 w UMTSIV 1700 V V UMTS 900 Ping Check Disable z First Server 0 0 0 0 Second Server Ping Check Count 0 Times Ping Check Interval 0 istRetrial 0 Seconds Interval 2nd Retrial 0 Minutes Interval T TCP Server Listening At scheduled time go Battery Intelimax User Manual IP Stack Auto Mode When using IP STACK Auto the modem will behave as an IP Serial modem When using this mode the modem will transfer all incoming packets via the serial port to the host and vice versa The modem connects to the 3G networks and acquires an IP address and then runs the IP STACK server or client mode Intelimax IP Stack can be configured as a Server or Client mode In Server mode the Intelimax will act as a socket server The modem will listen on a specific TCP UDP port waiting for an incoming client socket connection As soon as the client drops the socket connection the Intelimax will go back to socket listening mode as per IP stack configuration On the other hand with client mode the Intelimax will try to establish a socket connection to a preconfigured server IP address or DNS name and p
7. Use Ping command Check system up time Set the modem to factory default Reboot the modem Connecting to the modem via telnet To access the modem via Telnet or SSH you will need the following 1 A Telnet or terminal software you can use windows telnet Telnet needs to be enabled on the Intelimax Modem IP Address or Dynamic DNS URL Modem Username and Password Connection Steps 1 Run your telnet software and put the modem IP address or URL 2 Enter your username and password 3 Type help to display all available configuration commands Screen Shoots showing the different telnet commands Intelimax User Manual Type the name of a program folder document or Internet resource and Windows will open it for you Open This task will be created with administrative privileges Cancel Browse Once you login to telnet You can choose whether to start telnet service set up configuration Configure via AT command use ping function show uptime reboot and reset the modem remotely to factory default using option provided i e stat setup at ping uptime reboot and defconfig respectively ja Telnet 123 209 44 19 lt none gt login admin Password for help help setup at upt ime reboot exit INTELIMAR _ Intelimax User Manual Stat e Status of INTELIMAX upt ime reboot INTELIMAR dns INTELIMAX 1 DNS Addre 16 4 182 26 2 DNS Addre 18 4 81 183
8. then you can use the Intelimax to emulate the CSD modem interface The Intelimax can also be configured to act as an IP stack server for incoming connections if necessary IP CSD Connection Cel ular Netw rk Emulation ps I NN Internet Field device Intelimax i 172 16 0 1 Server 10 0 0 1 Dialing Process From the perspective of the field device it will dial out a CSD data call like it always has except the Intelimax will instead establish an IP stack client connection to the server For example the field equipment may dial the following string ATDT0412123456 then wait for the connection to be established by receiving a CONNECT message The Intelimax can be configured to establish an IP stack client connection to one of several different server IP addresses depending on the number dialled Intelimax Configuration The Intelimax must be configured in IP stack auto server or IP stack manual server mode This configuration can be made using the Intelimax GUI or via AT commanas If the Intelimax is in IP stack manual mode then it will only connect to the network when it receives the ATDT command via serial and will drop the connection when the call is hung up ATH If the Intelimax is in IP stack auto mode server then it will act as an IP stack server and therefore could be addressed remotely until it receives the dial out commands Intelimax User Manual RING Message To emulate the incoming CSD call th
9. IP address Trap 3 IP address OK DDNS AT DDNSS Intelimax User Manual DDNSS Disable OK Parameters DDNSS X X X X 0 1 Disable Enable DomainName UserName Password Service Provider OK System AT SYSTS SYSTS admin admin Enable 23 Enable Disable 192 168 0 50 Disable 61427933242 6142793324 2 61427933242 OK Parameters SYSTS X X X X X X X X X X X UserName Password 0 1 Telnet Disable Enable Telnet Port Number 0 1 Syslog Disable Enable 0 1 Remote syslog Disable Enable Remote syslog server address 0 1 SSH Disable Enable Phone number of Administrator Phone number of Administrator Phone number of Administrator OK Intelimax User Manual maxXconnect To enable maXconnect on the Intelimax either use the GUI or enter the following commands when the modem is in IP Stack Auto mode MAXCNT 0 120 portal maxconnect com au 1883 updates maxconnect com au OK AT MAXCNT 2 MAXCNT X X X X X 0 1 Disable Enable Refresh Interval Broker URL Broker Port FTP update server URL OK Serial UART port ATSSSPORT SPORT 115200 8 N 1 None OK Parameters SPORT X X X X X 2400 4800 9600 19200 38400 57600 115200 Baud rate 7 8 Data bits N E O None Even Odd 1 2 Stop bits None Software Hardware Flow control OK Engine Band ATSSBAND BAND 40000000 OK Intelimax User Manual Parameters BAND 1 GSM 850 2 GSM DCS SYSTEMS 4 GSM EGSM 900 8 GSM PGS
10. Remote Syslog R Syslog Server GO JI DY UT AWN Secure SHell Q Quit Whee Enable 23 Enable Disable 192 168 10 50 Disable 9 Admin Phone 1 Enter Phone Number 18 Admin Phone 2 Enter Phone Number 11 Admin Phone 3 Enter Phone Number M Main P Previous S Save Q M Main P Previous Save Q Quit Domain Nane Password Dynamic DNS Provider M Main P Previous maxon dyndns org maxon H Enable dyndns dyndns org 68 Intelimax User Manual M Telnet 123 209 44 19 M Main P Previous Save Q Quit WAN Scheduler WAN Scheduler UART Serial Port IPSTACK M Main P Previous Save Q Quit This command will allow users to select operating mode configure users name and password enter APN Enable Disable Auto PIN function enter PIN code and configure WAN scheduler 2 WAN Scheduler This command will allow users to control WAN connection in a specified time Day of week 0 6 Start hour 0 23 Start Minutes 0 59 Start hour 0 23 Start Minutes 0 59 Engine power 0 1 E g Scheduler 1 0 0 0 23 59 1 gt Sunday from 0 0 to 23 59 scheduler with engine power off 4 UART Serial Port This command allows users to configure serial setting e g baud rate data bit stop bit parity and flow control 5 IPSTACK Modem will be configured to use onboard IPSTACK This option allows changing IPSTACK Protocol TCP UDP IPSTACK Port and configu
11. Syslog System logs Remote Syslog IP address 192 168 10 50 Enter Phone Number Enter Phone Number Enter Phone Number Telnet and SSH login User Name setting using for Telnet and TCP conneciion Password setting using for Telnet and TCP conneciion Enable or disable Telnet Set Telnet port number to use Set SSH enable or disable Intelimax User Manual Syslog e Syslog allows viewing system logs plus enabling remote syslogs function and server IP address Save System logs in the internal memory Send modem Syslog to external sys logs server Enter the IP address of remote server RSSI logging e Configure the time period over which the RSSI logging will be averaged between 5 and 60 minutes The RSSI value is measured every 10 seconds Configure the level at which the RSSI signal strength will be considered high This is the level at which the PWR LED will flash solidly The RSSI values are saved to the RSSI log every 15 minutes and 90 days of logging can be recovered via the GUI Administrators e Administrator phone numbers can be added to restrict the SMS remote control messages to a limit number of phone numbers e Administrators phone numbers in international format 61412 345 678 maxXconnect maxXconnect is Maxon s a cloud based M2M management portal which allows you to access monitor and control 3G 4G Maxon devices securely With maxconnect you can access real t
12. below 11 9V Modem will be back to normal after battery voltage is over 12 3V Intelimax User Manual Scheduler The scheduler tab allows configuring modem WAN connection schedule The scheduler supports two methods of selection Days of the Week setup to come on certain days of the week or Setting up a certain power up duration setup to come certain during the hour Scheduler Day of the Week Using this option the user can specify days of the week when the modem will connect to the internet and would be online The connection and disconnection time is in 24 hour format While using the scheduler the RS232 and the 3G module can also be configured to shutdown to save power To setup Scheduler by Day of the week select the Day with the connect and disconnect times You can also set the modem to power off itself when it disconnects by checking the power off check box To delete an entry click on the entry and press the Remove selected Item button or if you want to remove all entered entries click the Remove ALL button Intelimax User Manual 7 RS232Control Power Off Day Connect Disconnect unr o fo o 00 w F PwroffModie D W Start Finish Power In the above example the modem will connect on Sunday 6 30AM and will disconnect at 5 30Pm and power itself off this feature is really handy if the modem is running on solar power Intelimax User Manual Scheduler by Duration
13. excluded SALES Hours of Operation Monday to Friday 8 30am to 5 30om Telephone 61 28707 3000 Facsimile 61 28707 3001 Email sales maxon com au Public holidays excluded WEBSITE www maxon com au ADDRESS Maxon Australia Pty Ltd 36a Gibson Avenue Padstow Sydney NSW Australia 2211 POSTAL ADDRESS Maxon Australia Pty Ltd Po Box 1 Revesby North Sydney NSW Australia 2212 Intelimax User Manual RF EXPOSURE AND ELECTRICAL SAFETY COMPLIANCE The use of this device in any other type of host configuration may not comply with the RF exposure requirements and should be avoided During operation a minimum of 20 cm should be maintained between the antenna whether extended or retracted and the user s bystander s body excluding hands wrists feet and ankles to ensure RF exposure compliance The modem is not designed for nor intended to be used in applications within 20 cm 8 inches of the body of the user Continued compliance of the equipment relies upon it being used with an AS NZS 60950 1 approved SELV power supply Caution Change or modification without the express consent of Maxon Australia Pty Ltd voids the user s authority to use the equipment These limits are designed to provide reasonable protection against harmful interference in an appropriate installation The modem is a transmitting device with similar output power to a mobile phone This equipment generates uses and can radiate ra
14. file only then generate another file for holding future input If the input is more than 10K bytes there should be more than one file generated each file should not exceed 10K bytes all these files will be sent to FTP server when time comes File uploaded with date time stamp disabled AT FTPCS 2 20 19 62 23 21 maxon maxon 1 FILEHEADER 10000 0 AT CSQ AT CSQ AT CSQ AT CSQ AT CSQ AT CSQ File uploaded with date time stamp enabled ATSSFTPCS 2 20 19 62 23 21 maxon maxon 1 FILEHEADER 10000 1 09 11 2012 15 44 05 AT CSQ 09 11 2012 15 44 06 AT CSQ 09 11 2012 15 44 07 AT CSQ 09 11 2012 15 44 08 AT CSQ 09 11 2012 15 44 09 AT CSQ 09 11 2012 15 44 10 AT CSQ 09 11 2012 15 44 11 AT CSQ 09 11 2012 15 44 12 AT CSQ 09 11 2012 15 44 13 AT CSQ 09 11 2012 15 44 14 AT CSQ 09 11 2012 15 44 15 AT CSQ ATSSFTPFL Intelimax User Manual Displays the files waiting to be uploaded ATSSFTPSC OK Will start the FIP connection and upload the files Can be used to force an upload when in periodic mode If no WAN connection is currently established such as in IP Stack Manual mode the Intelimax will establish the PPP and socket connections upload the FIP files then drop the socket and PPP connections Signal Strength AT CSQ CSQ 17 99 OK Open PPP connection ATSSIPCTOP Close PPP connection ATSSIPCTCP Open TCP UDP Socket ATSSIPCTOS Close TCP UDP Socket ATSSIPCTCS Change Remote Server IP address ATSSIPC
15. message up to 32 characters UDP Session Control To enhance the reliability of UDP IP Stack communication within the Intelimax we have introduced a new configuration option which provides Intelimax users with more control over the UDP activity and data communication The user can now enable or disable keep alive in conjunction with the Network Dormant period or alternatively specify Wake up time in seconds Wake up feature will send dummy UDP packets prior to sending any data received via serial port to setup a channel with the network The modem will send dummy packet twice as per timing set followed by the actual data This is to ensure the UDP data is not lost Network Dormant Period By default the network puts the modem in dormant or standby mode within 20 seconds of no data activity Keep Alive This sends a dummy UDP packet prior to modem going dormant and this is based on the Network Dormant Period This packet will be sent only if the modem doesn t send any data over the wireless network for the Network Dormant period Wake Up Wake up feature will send dummy UDP packets prior to actual data this wakes up the communication channel and guaranties sending the complete UDP data packet to the receiving end Enabling this could lead to additional delay in data transfer due to modem sending a dummy packet first to initialize the UDP connection with remote site FTP The FIP functionality on the Intelimax allows f
16. modem can operate in these are all outlined further in the PPP Server section 1 PPP WAN Auto mode Modem is a PPP server over serial with the WAN IP 23 Intelimax User Manual connection automatically connected PPP WAN Conditional mode Modem acts as PPP server with the WAN IP connection conditional on the serial PPP connection PPP WAN Manual mode Modem acts as PPP server and the WAN IP connection can be controlled via AT over IP commands Invalid PPP password characters list double quotation mark quotation mark 2 question mark bracket at sign semi colon pipe sign I Upper case I Band Change When band changing two reboots are required The first reboot will save the setting to the module and second reboot will apply the changes to the module so that module will register to the selected band Only bands which are supported by the module will be displayed in this section Users can change bands in serial modem mode via Intelimax GUI with the firmware 0 1 56 or later When band changing two reboots are required The first reboot will save the setting to the module and second reboot will apply the changes to the module so that module will register to the selected band For GSM 900 The user has to tick all GSM 900 bands to be able to connect to the GSM 900 band Double reboot is required Auto GsM850 GSMPCS V EGSM 900 v PGSM 900 4 RGSM 900 GSM 1800 GSM DCS UMTS
17. of the range Intelimax is a unique and intelligent fusion of 3G capabilities with advanced functionality of a modem router Intelimax Features General Features HSPA Wireless Module EM 820W 21Mbps downlink 5 6Mbps uplink Supports Packet and Circuit Switched Data RS232 connection 2 Way SMS Remote SMS diagnostics amp reset Embedded TCP IP UDP IP STACK Rugged plastic casing for industrial use Save and restore modem configuration from a file FOTA Firmware upgrade over the air External antenna connectivity to maximise HSPA coverage External LED to show Network and Connection status Extended Features Remote CSD to IP Changeover AT over IP FTP Client Programmable WAN connection scheduler SSH and Telnet support RSSI Logging Configurable ping checking function Backoff variable periodic resets and other network friendly features SNMPv2 and SNMPv3 SNTP Modem Emulation Dynamic DNS PPP Server Security Features Encrypted access and configuration control 12 Intelimax User Manual Password Protected AT Commands SNMPv3 supports SHA and AES SSLv3 Encrypted Serial Socket Login brute force detection and rejection Login activity log Frequency Bands WCDMA HSPA 850MHz 900MHz 1900MHz 2100MHz GSM GPRS EDGE 850MHz 900MHz 1800MHz and 1900MHz Data Speeds HSPA UL 5 76 Mbps DL 21 Mbps WCDMAPS UL384 Kbps DL 384 Kbps WCDMACS UL 64 Kbps DL 64 Kbps GPRS EDGE UL 236 Kbps DL 236 Kbp
18. that this material and the information contained therein are held in confidence and in trust and will not be used copied reproduced in whole or in part nor its contents revealed in any manner to others without the express written permission of Maxon Australia This information provided in this document is provided on an as is basis In no event will Maxon Australia be liable for any damages arising directly or indirectly from any use of information contained in this document Information in this document is preliminary and subjected to change without any notice Disclaimers Life support This product is not designed for use in life support appliances or systems where malfunction of these products can reasonably be expected to result in personal injury Maxon Australia customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Maxon Australia for any damages resulting from such application Right to make change Maxon Australia reserves the right to make changes without notice in the products including circuits and software described or contained herein in order to improve design and or performance Some features outlined in this manual may require an updated firmware version and or GUI version to work Please contact Maxon Australia for more information Intelimax User Manual INTRODUCTION Overview Breaking the industry benchmark the top
19. 168 2 1 1 3 6 1 4 1 910 SNMPv2 SMI enterprises 910 1 0 INTEGER 83 SNMPv2 SMI enterprises 910 2 0 INTEGER 1 SNMPv2 SMI enterprises 910 3 0 STRING 7 0dBm SNMPv2 SMI enterprises 910 40 STRING 88dBm MAXON MIB DEFINITIONS BEGIN IMPORTS OBJECT TYPE MODULE IDENTITY Integer32 enterprises FROM SNMPv2 SMI DisplayString FROM SNMPv2 TC MaxMIB MODULE IDENTITY LAST UPDATED 201104150000Z ORGANIZATION DHPLAB CONTACT INFO supportQOmaxon com au DESCRIPTION Maxon MIB REVISION 2011041500002 DESCRIPTION This file defines the maxon mib by dhplab n enterprises 0910 signalStrength OBJECT TYPE SYNTAX Integer32 0 105 5 Intelimax User Manual MAX ACCESS read only STATUS current DESCRIPTION Signal strength of the modem MaxMIB 1 registrationValue OBJECT TYPE SYNTAX Integer32 0 5 MAX ACCESS read only STATUS current DESCRIPTION Registration of the modem L MaxMIB 2 ecioValue OBJECT TYPE SYNTAX DisplayString MAX ACCESS read only STATUS current DESCRIPTION EC IO of the modem MaxMIB 3 rscp OBJECT TYPE SYNTAX DisplayString MAX ACCESS read only STATUS current DESCRIPTION RSCP of the modem MaxMIB 4 imei OBJECT TYPE SYNTAX DisplayString MAX ACCESS read only STATUS current DESCRIPTION IMEI of the modem MaxMIB 5 boardreset OBJECT TYPE SYNTAX Integer32 0 1 MAX ACCESS read write 52 Intelimax User Manual STATUS current DE
20. 2100 UMTS III 1700 UMTS IV 1700 UMTS IX 1700 UMTS 800 UMTS 900 UMTS 850 UMTS 1900 Intelimax User Manual For UMTS 850 The user will be able to lock to UMTS 850 network by just ticking the UMTS 850 band in the GUI Double reboot is required E Auto GSM 850 GSMPCS PGSM 900 RGSM 900 _ GSM 1800 UMTS 2100 UMTS III 1700 SIV UMTS IX 1700 UMTS 800 Vii F UMTS 1900 WAN page allows configuring the following features e APN and dialup string e Username and password for IP WAN e Auto pin settings Intelimax will enter the PIN code if SIM pin is Enabled Network authentication information Watchdog Ping Function Back off timer Periodic reset o Can be enabled or disabled o Configurable by number of hours between 1 and 28 Reset state setting Reset will happen in any state unless configured otherwise by TCP Server Listening For use in IP Stack Auto Server mode If checked will wait until TCP connection is dropped by either server or client before performing the reset TCP Connection State For use in IP Stack Auto Client mode If checked will wait until Intelimax client drops connection to a server or server drops connection before performing the reset e Battery o When ticked modem will enter idle mode cellular module and serial port are switched off when battery voltage is
21. Australia Pty Ltd AT CGMR Firmware version CGMR 2 0 8 201409230653 AT CGSN IMEI number 354283049080793 Wan extension function ATSSWANSE WANSE PINGCHECK Enable 0 0 0 0 0 0 BACKOFF Disable 0 0 0 0 OK Parameters WANSE X X X X X X 0 1 PINGCHECK BACKOFF Intelimax User Manual 0 1 Disable Enable both expansion PINGCHECK and BACKOFF 1 60 Interval of PINGCHECK 40 59 Seconds of Ist retrial interval of BACKOFF 1 60 Fail count of PINGCHECK 2 10 Minutes of Ist retrial duration of BACKOFF IP address of Ist server of PINGCHECK 10 59 Minutes of 2nd retrial interval of BACKOFF IP address of 2nd server of PINGCHECK 2 10 Hours of 2nd retrial duration of BACKOFF OK WAN authentication ATSSWANSA WANSA 1 telstra extranet 0 99 0 0 0 0 0 00 00 0 OK Parameters WANSA X X X X X X X X X X X X X X X X 1 2 IPStack Auto Manual Access Point domain Name 0 1 2 NONE PAP CHAP Username Password Dialup number 0 1 Auto PIN Disable Enable PIN code 0 24 Hours of Periodic reset 0 1 Disable Enable Reset TCP Server Listening Server If enabled will wait until client drops connection 0 1 Disable Enable Reset TCP Connected State Client If enabled will wait until Intelimax client drops connection to a server or server drops connection 0 1 Disable Enable Reset At scheduled Time HH MM for Reset At scheduled Time 24 hour format Battery 12 3 volts ON 11 9 volts OFF 0 1 100 LCP Echo Inte
22. Call ATSO n Set auto answer where n number of rings Escape command to enter AT command mode 1 second gap both before and after command required to distinguish from data ATH Drops the data call ATO Can return to call if still active To use this feature please ensure the following has been setup on the SIM 1 Contact SIM service provider and make sure that CSD is activated on the Sim card Generally this requires a second number data terminating number attached to the same service Configure the modem to auto answer the call or make sure that the equipment connect to the modem has auto answer activated to detect an incoming call and sends ATA to answer the data call Packet Switch Data Call The Intelimax supports PPP over serial connections through the modem and utilizes standard AT commands for this purpose It is recommended that user dial out control code executes a hang up process command before each reconnection attempt by issuing a command followed by and ATH command Standard set of AT commands used with PPP call ATD Dial the PPP number e g 99 Escape command to enter AT command mode 1 second gap both before and after command required to distinguish from data ATH Drops the data call ATO Can return to call if still active PPP Server Options The Intelimax can be configured to act as a PPP Server over the serial interface with an independent PPP WAN connection There are three different PPP modes the
23. Command AT IPCTOS IP Stack Disconnect AT Command AT IPCTCS Intelimax User Manual IP Stack Connect Button When IP Stack is Manual Mode connect without AT Command input IP Stack Disconnect Button When IP Stack is Manual Mode disconnect without AT Command input Send CR LF Add Carriage Return and Line Feed message when data is sent Use for AT Command sending via the GUI Send Button Send AT Command and Data System Functions System Functions agen T som eaa seve FIW upload Clear Output Delete modem output information Save Output Save Output Info s information as a File Save Config Save modem configuration as a file Load Config Load modem configuration information as a file Factory Setting Reset Intelimax to factory settings Intelimax User Manual Firmware Upgrade Upgrade the Intelimax s firmware Intelimax Port coma Baud Bateaalas O E sa ee E ANE gO W lt lt Intelimax Firmware Firmware Search Firmware D Organize v New folder dzy M Modem Configuration x Exon Date modified EL Desktop IB Downloads T Recent Places 3 Dropbox 4 Google Drive No items match your search Libraries E Documents d Music E Pictures ist Trap Server IP E Videos 2nd Trap Server IP 3rd Trap Server IP coments Sg Backup BA 07FEFA B m File name
24. Intelimax User Manual imteimax lt Intelimax M2M 3G Serial Modem MA 2015 User Manual Not to scai 4 This manual is the sole and exclusive property of w mexon sta actex Maxon Australia australa Not to be distributed or divulged without prior written agreement wWww maxon com au Intelimax User Manual TABLE OF CONTENTS CONTACT INFORMATION RF EXPOSURE AND ELECTRICAL SAFETY COMPLIANCE Caution General Safety Vehicle Safety Potentially Unsafe Areas REVISION HISTORY Intelimax USER MANUAL Disclaimers INTRODUCTION Overview Intelimax Features General Features Extended Features Security Features Frequency Bands Data Speeds Environmental Specifications Dimensions Connections Mounting LED Lights Module Approvals Modem Approvals Compliance Power Source Operating Systems Hardware compatibility Intelimax Setup Connecting to the Intelimax TCP IP Connection Recommended Serial Port Connection GUI Connection Debugging Modem Configuration Intelimax User Manual Modem Status Tab Scheduler Scheduler Day of the Week sssssassassasnasnasnaznaznaznASNASRASNASNM 26 Scheduler by Duration Serial Configuration IP Stack Configuration Modem Emulation TAB Dynamic DNS PPP Server maXconnect System settings page AT over IP Send CR LF Send Button System Functions Clear Output Save Output Save Config Load Config Factory Setting Firmware Upgrade SMS Commands IP mo
25. M 900 10 GSM RGSM 900 20 GSM PCS 40 WCDMA I IMT2000 80 WCDMA II PCS1900 400 WCDMA V 850 1000 WCDMA VIII 900 40000000 AUTO OK Examples GSM 850 900 1800 1900 AT BAND 3f BAND 0000003f OK The AT commands on the module can be set and checked directly using AT DIRAT AT DIRAT atAsyscfg 2 2 380380 1 2 make sure module band is set OK AT amp W OK AT RESET OK WCDMA 850 AT BAND 400 OK AT DIRAT ATASYSCFG 2 2 4000000 1 2 83 Intelimax User Manual OK AT amp W OK AT RESET OK Check IP address of the WAN side ATSSWAN WAN 123 209 0 204 OK FTP To use FIP on the Intelimax allow for append on the FIP server Also restrict the welcome message to less than 10 characters Please save and apply settings before using AT FTPCS AT FTPCS 1 192 168 10 1 21 maxon maxon 0 INTELIMAX 1000 1 OK Parameters FTPCS X X X X X X X X 0 Disable 1 Manual 2 Hourly O 24 3 Time of day 0 24 4 Day of month 1 31 days 5 Minutes 0 60 Host IP Domain address with Port User name Intelimax User Manual Password Time interval Header of file name limit 10 bytes characters Size of file Bytes maximum 102 400 bytes maximum internal buffer size 1 OMB A new file will be created each time the file size is exceeded Time stamp enable 1 or disable 0 timestamp prefix in seconds A reboot is required when enablin
26. Microsoft Windows PPP client Before initiating the PPP connection it requires the exchange of the text strings CLIENT from the client 43 Intelimax User Manual and CLIENTSERVER from the serer So in MS Chat mode the Intelimax PPP server will expect a CLIENT string from the client and then send back CLIENTSERVER No Dial mode means the client PPP will initiate PPP connection without any dialing string being sent prior to PPP session THIS IS NOT CURRENTLY SUPPORTED In Modem Emulation mode the PPP client will send dialing strings such as ATVI AT CGATT 0 ATDT 99 14 etc and user can define dialing strings to be sent to the PPP server The user can also define what string it will expect to hear back from PPP server before the PPP connection is initiated In this mode two fields need to be configured through the Intelimax GUI to make PPP server answer client device accordingly Modem Configuration Status WAN Scheduler Serial IP Stack Emulation DDNS PPP Admin System Enable DONS Service Provider Domain Name User Name Email Password Key PPP Server Dial Mode fe 0 0 0 0 AccM lPComp lvJcomp F Proxy ARP E Magic Dialup String CLIENT Answer String CEER Authentication Username Password MRU Idle timeout Forward Save Config to Modem l Load From Modem Rebootmodem All AT commands for dialing should be sent
27. S W Version 8 6 74 261268311363 System Time 2612 69 12 89 32 34 IP Address 123 209 44 193 INTELIMAX Sep 12 69 32 37 user i Sep 12 69 32 user i Sep 12 69 31 user i Sep 12 69 31 user i Sep z z user i Sep 30 user i Sep S z user i Sep 29 user i Sep FLE user i payload payload payload payload payload payload payload payload payload ONHHHNNHNH M E M E M E ME E AAA ked ked ked ked ked ked ked ked ked 699999999 B D D una Shows the syslog information if it is not set as remote syslog Sysinfo Shows F W version and system Time and IP Address of Intelimax Display Primary DNS and secondary DNS address of Intelimax Intelimax User Manual SYSTEM DDNS Mode SNMP SNTP M Main P Previous SzSave Q Quit 1 SYSTEM Users can change Admin password telnet port Enable Disable Remote Syslog and can enter up to three phone number for SMS Users can configure Dynamic DNS using this command Intelimax support IP stack and Serial mode only using this option Mode users can configure WAN scheduler UART Serial port setting and IP stack setting Users can enable disable this feature that allows network monitoring Users can enter server address Activate and De activate day light saving and even change time zone ja Telnet 123 209 44 193 M Main P Previous Admin Name Admin Password Telnet Daemon Telnet Port Syslog Daemon
28. SCRIPTION Board reset MaxMIB 6 firmware OBJECT TYPE SYNTAX DisplayString MAX ACCESS read only STATUS current DESCRIPTION Firmware version of modem MaxMIB 7 firmwareModule OBJECT TYPE SYNTAX DisplayString MAX ACCESS read only STATUS current DESCRIPTION Firmware version of module i MaxMIB 8 SNTP SNTP can be used to update the time of the Intelimax The modem will by default take its time from the network When SNTP is enabled the modem will query a network based NTP server using the SNTP protocol and pull the time from it The timezone can be configured depending on where in the world the modem is used If the daylight savings setting is configured the modem will add an additional 1 hour to the system time setting If SNTP is not configured correctly or the server is not available then it can cause the system logs to incorrectly record as they are referenced to system time The minutes configuration can only be set to 30 minutes Intelimax User Manual Output Info Manufacturer Maxon Electronics Australia Pty Ltd Model Number MA 2015 Product Name Intelimax F W Revision 0 0 18 201205241255 H W Version 1 8 Module F W Revision 11 810 10 01 00 Output Information for receiving Intelimax s data in serial or remote access When syslog are requested this is where they are printed before being saved to a file IP Stack Functions IPStack Functions FlsendcR u IP Stack Connect AT
29. TRIP 0 ip ad dr ess lt port gt Eg ATSSIPCTRIP 0 123 456 789 01 30000 Change client server mode ATSSIPCFL 4 lt 0 1 gt where 0 for server 1 for client 87 Intelimax User Manual Eg ATSSIPCFL 4 0 sets modem to server mode IPStack Connection Settings ATSSIPSCFG IPSCFG 30 100 300 OK AT IPSCFG 2 IPSCFG X X X IPSTACK SEND DELAY 1 2000 msec IPSTACK BUFFER SIZE 32 1450 bytes IPSTACK SOCKET TIMEOUT lt 0 10 3600 gt sec PPP DISCONNECT TIMEOUT lt 0 30 3600 gt sec OK AT IPSCFG 30 100 200 301 OK AT IPSCFG IPSCFG 30 100 200 301 OK Change modem mode ATSSCHGMODE 1 IP Stack Auto 2 IP Stack Manual 3 Serial Modem at chgmode 1 OK Save and Reboot ATSSRESET At reset OK Factory Reset ATSSFACTORY OK Intelimax User Manual AT over IP on IPStack ATSSOVERIP OVERIP X X 0 1 Disable Enable Listen Port Number OK at overip OVERIP 1 12521 OK at overip 0 Require Save and System Reboot OK at overip OVERIP 0 12521 OK at overip 1 12522 Require Save and System Reboot OK at overip OVERIP 1 12522 OK Intelimax User Manual Modem Emulation The Intelimax modem emulation can be configured using the following AT commands To enable modem emulation and add a data number to IP address and port number emulation to the list at emul 1 ohone_number P_address port_number e g at emul 1 0104420441 4 10 0 0 1 5000 To check current emulati
30. ax SMS Syntax INTELIMAX PARK REBOOT RSSI Info SMS Syntax INTELIMAX PARK RSSI Response RSSI lt RSSI in dBm gt e g RSSI 67 57 Intelimax User Manual DDNS configuration change by SMS SMS Syntax INTELIMAX PARK DDNS1 lt mode gt lt host address gt INTELIMAX PARK DDNS2 lt domain name gt lt user id gt lt user password gt SMS Commands Serial modem modes The Reboot Intelimax SMS command can be used to act on Intelimax specific SMS messages when in serial modem mode For this to happen the modem must be told to intercept the SMS messages using the AT STEALTHSMS command AT STEALTHSMS STEALTHSMS 0 OK AT STEALTHSMS 0 disable modem interception of SMS messages OK AT STEALTHSMS 1 modem to intercept SMS message OK Reboot Intelimax SMS Syntax INTELIMAX PARK REBOOT RSSI Info SMS Syntax INTELIMAX PARK RSSI Reply message syntax RSSI lt value gt e g RSSI 57 Change mode via SMS SMS Syntax INTELIMAX PARK CHGMODE lt 1 IPStack Auto 2 IPStack Manual 3 Serial Modem gt e g INTELIMAX PARK CHGMODE 1 Reply message syntax Mode Change To lt mode gt e g Mode Change To IPStack Auto The modem will automatically reboot after sending the response Intelimax User Manual PROGRAM INTELIMAX VIA CIRCUIT CALL The Intelimax has the unique in built feature of being able to change between modes and configure settings remotely over a CSD call This is especially useful if you
31. before the dialup String the special command ATDT 99 will inform the Intelimax to go into a PPP exchange string mode listening to the dialing string defined after the ATDT 99 1 command In Modem Emulation mode before the PPP connection is established AT commands are supported to change settings in the modem or collect information from the modem All standard AT commands and Maxon customized AT commands are supported The command ATDT 99 14 is to notify the Intelimax to go into the PPP 44 Intelimax User Manual mode after this command no more AT commands are supported through direct accessing of the serial port To continue to use AT commands after PPP conneciion AT over IP to port 12522 can be used The dialup string such as cr1000dial should be entered in the dialup strings section Other PPP Options ACCM Async Control Character Map enable or disable PComp Protocol field compression negotiation enable or disable VJ comp Van Jacobson style TCP IP header compression enable or disable Proxy ARP Proxy Address Resolution Protocol enable or disable Magic Magic Number Negotiation enable or disable Please see https samba or d html for further detail Authentication PPP server supports 3 authentication modes None CHAP and PAP Whenever CHAP or PAP authentication mode is selected the username and password should be provided as well otherwise these two fields can be left blank Modem Confi
32. des SMS Commands Serial modem modes 3 Intelimax User Manual PROGRAM INTELIMAX VIA CIRCUIT CALL LED Functionality Modem Debugging Local Connection Checking Remote Connection Checking Telnet SSH Commands Connecting to the modem via telnet Extended Intelimax Specific AT Command Set IP Stack Modes Device Information Wan extension function WAN authentication Periodic reset Serial UART port Engine Band Check IP address of the WAN side Signal Strength Open PPP connection Close PPP connection Open TCP UDP Socket Close TCP UDP Socket Change Remote Server IP address Change client server mode IPStack Connection Settings Change modem mode Save and Reboot Factory Reset AT over IP on IPStack Modem Emulation Modmax Compatibility Mode Intelimax User Manual TCP Delay between trying to connect socket and CONNECT messages Prepare modem for hard shutdown SMS on Boot Extended Module Specific AT Command Set Serial Modem Mode 93 Periodic Reset Getting SO value in serial modem mode Single AT command SMS AT MMC SMSMO Prepare modem for hard shutdown SMS on Boot Intelimax User Manual CONTACT INFORMATION In keeping with Maxon Australia s dedicated Customer support policy we encourage you to contact us TECHNICAL Hours of Operation Monday to Friday 8 30am to 5 30om Telephone 61 28707 3000 Facsimile 61 28707 3001 Email supportamaxon com au Public holidays
33. dio frequency energy and if not used in accordance with instructions can cause harmful radiation to radio communication The modem is approved for use with the antenna ANT FME Unauthorized antennas modifications or attachments could impair call quality damage the device or result in violation of RF exposure regulations There is no guarantee that interference will not occur in a particular installation If the equipment does cause harmful interference in radio and television reception which can be determined by turning the equipment on and off the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving radio or TV antenna Increase the separation distance between the equipment and the receiver Contact Maxon Australia Technical Support for assistance Intelimax User Manual General Safety RF Interference Issues Avoid possible radio frequency RF interference by carefully following safety guidelines below Switch OFF the Modem when in an aircraft The use of cellular telephones in aircraft is illegal It may endanger the operation of the aircraft and or disrupt the cellular network Failure to observe this instruction may lead to suspension or denial of cellular services to the offender legal action or both Switch OFF the Modem in the vicinity of gasoline or diesel fuel pumps or before filling a vehicle with fuel Switch OFF the Modem in hos
34. e Intelimax will print out RING messages a a rate of 1 RING per second according the SO setting In order to account for this delay when dialling out through the modem it is advisable to add a CONNECT message delay using the AT TCPDEL lt MS gt command e g AT TCPDEL 2000 for a 2 second delay before printing out the CONNECT message this command can only be set via AT commands not through the Gul GUI Configuration Modem Configuration Status WAN Scheduler Serial IP Stack Emulation ppns ppP Admin System Modem Emulator Enable z Phone Number Port m EEN Phone Number Destination Address 0400123456 10 0 0 10 Delete Selected Save Config to Modem Load From Modem Reboot modem Up to 40 phone numbers can be added to match to destination IP addresses and port numbers It is recommended that 5 10 numbers are added at a time through the GUI before saving and rebooting the modem to reduce the risk of GUI connection timeout and lost entries Intelimax User Manual Dynamic DNS Allows the user to configure Username Password and Domain name to be used by Intelimax when authenticating on a DDNS server Enable DDNS Select to enable DDNS Service Provider Link of the DDNS service web page Server site is http dyn com by default Domain Name Set DDNS host name or Alias from DDNS server User Name Email Input User Name for logging onto a DDNS serve
35. e by you can configure the modem via serial connection or remotely via the WAN IP E Z Intelimax GUI 56 Serial Port Connection TCP IP Connection Port COM9 Baud Rate 115200 Open Close Address 192 168 10 1 Data Bit 8bit Parity None Stop Bit 1bit w Flow Control None v ID admin _ Find the modem with standard buad rate Output Info Modem Configuration TCP IP Connected Status WAN Scheduler Serial IP Stack Emulation DDNS PPP Admin System Up Time Oday 2h 39m 3s System Time 2015 07 01 15 10 05 IMEI 357042060064145 Version 1 1 8 201507011109 H W Version 2 0 IM2 Module Version 03 001 Network Registration Telstra Mobile Local network registered Packet Switched WCDMA PS attached Gear output Save Output PIN Status PIN request deactivated Area Information LAI 50501 LAC 151 CellID 00ea 1ca8 j ntel i m a X ignal Level 73 dBm Ava 72 Max 63 Min 72 ent Generation MOM HSPAe Nael Mode IPStack Auto zupportGrnaxon com au 61 2 87073000 www 7 maxon astrala Server Status Listening IPStack Functions WAN IP 172 16 0 9 IPStack Connect IPStack Disconnect 7 Send CR LF Sent Packets 9 292 Bytes AT CHGMODE 3 Received Packets 5 56 Bytes System Functions Kuo WoS Go GA Set profile J Load profile Factory Partialupload Moduleupload B Lupoad _ F Wup ad
36. e then the same private key and certificate are used the ca pem certification file is not used by SSLv3 How to generate SSL certificates A SSL certificate can be generated using an application such as OpenSSL http sloroweb com products Win32OpenSSL html the lite version is fine To generate certificate for client and key for client key pem cert pem C OpenSSL Win32 bin gt openssl req new x509 days 3650 nodes config openssl cfg out cert pem keyout key pem This application can be run from the command line for example C OpensSL Win32 bin gt openssl req new x509 days 365 nodes config openssl cfg out cert pem keyout key pem The resultant 2 certificate files contained in the bin folder and are named cert pem 32 Intelimax User Manual and key pem Mode Intelimax supports operation of the IP Stack in either client or server modes e Server mode In Server mode the modem will connect to a PPP session and will listen on a predefined port for incoming client requests Client mode the modem will initiate a PPP connection and try to connect to the Primary server If the connection to the server fails 10 times it will try the Secondary server if the connection to the secondary server also fails for 10 times the modem will drop the PPP connection reboot and start all over again Primary Server Define the IP Address or DNS address of the primary server the Intelimax will try to connect to in Client m
37. egulations on the use of cellular devices in vehicles Road safety always comes first If incorrectly installed in a vehicle the operation of the modem could interfere with the correct functioning of vehicle electronics To avoid such problems ensure that the installation has been performed by qualified personnel Verification of the protection of vehicle electronics should be part of the installation Note The user is cautioned that changes or modifications not expressly approved by Maxon Australia could void the warranty Potentially Unsafe Areas Posted Facilities Turn off the device in any facility or area when posted notices require you to do so Blasting Areas Turn off the device where blasting is in progress Observe restrictions and follow any regulations or rules Potentially Explosive Atmospheres Turn off the device when you are in any area with a potentially explosive atmosphere Obey all signs and instructions Sparks in such areas could cause an explosion or fire resulting in bodily injury or death Areas with a potentially explosive atmosphere are often but not always clearly marked They include Fueling areas such as gas or petrol stations Below deck on boats Transfer or storage facilities for fuel or chemicals Vehicles using liquefied petroleum gas such as propane or butane Areas when the air contains chemicals or particles such as grain dust or metal powders Avoid using the modem in areas that em
38. er and wait for the user device PPP client to connect Once the PPP connection is established the device can talk to the Intelimax through a network connection The Intelimax then acts like a network gateway all data traffic from the device will be routed to the WAN interface and then be sent to the internet In all PPP server modes traffic from end device to internet is masqueraded behind modem WAN IP The device can use any TCP UDP port to talk to peer applications on the internet side thus the dedicated TCP UDP socket connection between the Intelimax and user server application is no longer needed the user device can open socket directly Intelimax User Manual There are WAN working modes described below that will work in this scenario For more information about PPP WAN modes please refer to next chapter e PPP WAN Auto e PPP WAN Conditional e PPP WAN Manual PPP WAN modes PPP WAN Auto In this mode the WAN IP connection is always connected PPP WAN Conditional In this mode the WAN IP connection is based on the LAN PPP connection once the LAN PPP connection is up the WAN IP connection will be established and vice versa This is to save data usage and device power consumption PPP WAN Manual In this mode the device needs to send commands to bring up bring down the WAN IP connection The command are sent over the LAN PPP connection through the serial cable these are custom AT over IP commands not to i
39. erface of the Intelimax internal cellular module or the Intelimax specific modem AT commands The AT over IP function can be used either over the local USB LAN interface to the modem or via a remote IP conneciion This can be useful for remotely checking signal strength sending SMS messages through the modem etc While the AT over IP connection to the module is in use the modem cannot communicate via AT commands to the module so it isrecommended to only open the port for less than a minute at a time Debug The debug settings allow for additional debug levels to be set in the modem to allow for additional debugging capabilities When these debugging settings are enabled the 50 Intelimax User Manual syslogs system logs contain additional information for either the engine or IP stack These should only be turned on for short periods of time while debugging and turned off once debugging has been completed SNMP Configuration Simple Network Management Protocol SNMP is the protocol governing network management and the monitoring of network devices and their functions It is not necessarily limited to TCP IP networks From firmware version 0 1 56 the Intelimax supports SNMPv3 With the Intelimax SNMP customers can read the modem Signal Strength registration value ecio rscp IMEI firmware and module firmware values as well as reset the modem via SNMP MIB as shown below bjoh bjoh pc snmpwalk v 2c c public 192
40. g disabling or making changes to the FTP options Examples AT command to upload every I hour AT FTPCS 2 20 19 62 23 21 maxon maxon 1 FILEHEADER 10000 0 AT command to upload every 30 minutes AT FTPCS 5 20 19 62 23 21 maxon maxon 30 FILEHEADER 10000 0 AT command to upload every day at 8PM AT FTPCS 3 20 19 62 23 21 maxon maxon 20 FILEHEADER 10000 0 AT command to upload every 15th day of the month AT FTPCS 4 20 19 62 23 21 maxon maxon 15 FILEHEADER 10000 0 In the example above file size is 10000 bytes The modem would create a text file using name specified above in the example I have used fileheader as the filename The last setting O or 1 decides if the data is time stamped O will only log data in the text file 1 will stamp all data logged with date and time The size of file parameter is used for limiting the file size of the csv file All the input from serial port will be saved in the csv file and once the file size of that csv file exceed the size limit another file will be created to hold the input The value allowed is 1000 100 1000 Bytes 85 Intelimax User Manual Based on the configuration the file could be uploaded to server periodically For example AT FTPCS 5 192 168 10 50 21 maxon maxon 30 FILEHEADER 10000 0 with this setting the modem will send out csv file to FIP server every 30 minutes If the input has not exceeded limit 10K bytes in this case modem will send this
41. guration status WAN Scheduler Serial IP Stack Emulation DDNS PPP Admin Enable DDNS Disable L Service Provider Domain User Name Password Key PPP Server Dial uP s E RIP Fjaccm Pcomp vJcomp prag ARE C Magic Dialup Answer Authentication Username Password MRU Idle timeout Forward Save Config to Modem Load From Modem Reboot modem Intelimax User Manual MRU Maximum Receive Unit The PPP server will ask the client to send packets of no more than MRU bytes The value must be between 128 and 16384 the default is 1500 Idle Timeout This is to specify that PPP server should disconnect if the PPP link is idle No data traffic for Idle seconds Port Forwarding The Forward section is for entering the port forwarding options with the following format Incoming port WAN Outgoing port LAN e g 8080 80 port 8080 on the WAN interface is forwarded to port 80 on the LAN interface Extra port forwards are separated with a comma Currently only individual ports can be forwarded but port ranges will be added An additional white paper on PPP server functionality is available from Maxon Intelimax User Manual Administration Modem Configuration Status WAN Scheduler Serial IP Stack Emulation DDNS Admin system Telnet Teret i Username admin Password Telnet Port Number
42. have a modem in the field that you need to remotely configure using remote AT commands or the Intelimax GUI but are currently using CSD to talk to this modem Using these commands lets you change to an IP connection for easy access to the device over an IP connection This feature is available from firmware versions 0 1 67 onwards It is very important to ensure that you can access your modem once this is done which means either using a static IP address private IP WAN or similar or a public dynamic IP address such as telstra extranet the WAN IP of which can be found via SMS Dialing Process Dial out to the modem via a command line terminal session to your data modem using the data number of the SIM card in the Intelimax The sting will be as follows ATDT0400123456 Once the CONNECT message has been displayed you are connected Intelimax Remote Configuration Commands The following commands can be used to change the settings of the Intelimax Unlock the CSD programming interface program maxon unlock admin admin admin admin are the default username and password if you have changed these update this command with the appropriate values in the order username password Update the cellular APN program maxon apn telstra extranet Update the CPN username password and authentication program maxon auth userid password chap pap none Change the mode of the modem program maxon mode 1 Where IP Stack Auto mode auto connect IP
43. ime data from your devices monitor their status and location Utilise complete functionality by controlling your devices anywhere anytime This one stop portal is an access point to manage your 3G 4G assets securely and remotely Use within maXwan maxconnect can be used when the device is connected to the Internet or within maxwan e The default settings for general internet connections are as follows o maxXconnect URL portal maxconnect com au o maXconneci port 1883 o maxXconnect update interval 120 seconds maxXconnect FIP server URL ftp maxconnect com dau 48 Intelimax User Manual e For connections to MaxConnect within MaxWAN please use the following O O O maxXconnect URL 10 0 0 1 maxXconnect port 1883 maxXconnect update interval 120 seconds maxconnect FIP server URL 10 0 0 32 Intelimax User Manual System settings page Modem Configuration status WAN Scheduler Serial IP Stack Emulation DDNS PPP Admin AT over IP Debug Moda ge Modem 12522 stack Lock out Attempts 3 lt Period 30 Sec Sessin Timeout 2 gt Mins SNMP System Name DHAGENT System Contact support maxon com au System Location AUS Write Community Name private Read Community Name public ist Trap Server IP 192 168 0 200 2nd Trap Server IP 192 168 0 201 3rd Trap Server IP 192 168 0 202 SNTP AT over IP AT over IP can be used to access the AT command int
44. in Password admin TCP IP Connection Address 192 168 10 1 Port 10918 ID admin Password eeeee Note Power via USB doesn t work in MA 2015 please use MA 2015S with Diode enable modem in order to power via USB Intelimax User Manual Remote Connection Users can also access the Intelimax remotely via a static IP address e g maXwan or via a url e g DynDNS TCP IP Connection Address intelimax dyndns biz ID admin Serial Port Connection Use this section to connect to the modem using the provided RJ45 power serial cable the default connection settings are Baud Rate 115200 Databit 8 bit Parity None Stop bit 1 bit Flow control None bt Party fire stoper Et Fow cota one gt E Find the modem with standard buad rate Make sure to select the correct COM port and click the open button the Intelimax GUI will connect to the modem via the selected COM port The GUI can also perform a search for the correct baud rate if it is not known The configuration operations available over a serial connection to the modem are limited when compared to a TCP IP connection Intelimax User Manual GUI Connection Debugging 1 What if don t know the serial interface to the modem The modem has a default baud rate of 115200 if you are not able to connect via the serial interface at any baud rate then restore the modem to factory defaults by holding down the reset button for mo
45. interval Header of file name limit 10 bytes characters Size of file Bytes maximum 102 400 bytes maximum internal buffer size 10MB A new file will be created each time the file size is exceeded Time stamp enable 1 or disable 0 timestamp prefix in seconds Each file will have a standard prefix used here with a suffix in the format DDMMYYYHHMMSS where D is day M is month Y is year H is hour in 24 hour format M is minutes and S is seconds E g DHMAX10102014181146 csv A reboot is required when enabling disabling or making changes to the FTP options The size of file parameter is used for limiting the file size of the csv file All the input from serial port will be saved in the csv file and once the file size of that csv file exceed the size limit another file will be created to hold the input The value allowed is 1000 100 1000 Bytes Based on the configuration the file could be uploaded to server periodically For example FTP Minutes 0 60 z FTP Server 192 168 10 1 FTP Port Number Username admin File Name DHMAX Time Interval 30 21 Password admin File Size bytes 10000 Time Stamp Disable v With these settings the modem will send a csv file to the FTP server every 30 minutes If the input has not exceeded limit 10K bytes in this case modem will send this file only then generate another file for holding future input If the input is more than 10K bytes there sho
46. it electromagnetic waves or enclosed metallic structures e g lifts Any other area where you would normally be advised to turn off your engine m Intelimax User Manual REVISION HISTORY Product Intelimax M2M 3G Serial Modem Model MA 2015 Document Type PDF Current Version Number 8 0 Status of the Document Release Revision Date September 2015 Total Number of Pages 95 Revision History Level Date History 1 0 May 2012 Internal Draft Version 5 0 November 2012 Stable Release Version 7 2 July 2013 Stable Release Version Use July 2013 Added new AT commands 7 4 October 2013 Added Modem Emulation maXconnect SMS on boot SMS Reboot in Serial mode 7 5 April 2014 Updated AT commands 7 6 May 2014 Updated FTP section and Invalid PPP password characters VA October 2014 Updated AT command section and E die notice 7 8 March 2015 Corrected the errors in LED Functionality Table Added details of AT SPC command 7 9 June 2015 Added PPP Server Functionality 8 0 September 2015 Updated with SSLv3 socket Intelimax User Manual Intelimax USER MANUAL All data and information contained in or disclosed by this document are confidential and proprietary information of Maxon Australia and all rights therein are expressly reserved By accepting this material the recipient agrees
47. m using the SEIE Intelimax User Manual configuration GUI 2 In IP Stack modes a Open the GUI with an IP connection to the modem and log in i Check that the settings are correct for the equipment that you are wanting to connect to including the serial baud rate etc Check that the signal strength is of a good level better than 81 dBm b Use an SNMP viewer to connect to the modem SNMP server i Check signal strength good levels are better than 81 dBm ii Check that the modem settings are correct 3 In either mode send an SMS to the modem to perform the following a Check RSSI By sending INTELIMAX PARK RSSI to the modem the modem will respond with the RSSI which should be better than 81 dBm Check APN and WAN connection using INTELIMAX PARK WANIP The response is IP lt IP IP IP IP gt APN lt APN gt D lt ID gt PW lt PW gt Auth lt PAP CHAP BOTH gt Reg lt 0 1 gt Sig lt CSQ gt If neither command work then reboot the modem using INTELIMAX PARK REBOOT Intelimax User Manual Telnet SSH Commands Using Intelimax Telnet SSH commands allows you to configure the modem remotely also you can send diagnostic commands here is summary off of tasks that you can perform 1 Stat Used to display sys log system info and DNS settings 2 Setup using this menu you can setup system settings Dynamic DNS operation mode SNMP and SNTP settings Send Direct AT commands to the modem module Check signal strength
48. nternal module AT IPCTOP to open WAN PPP connection AT IPCTCP to close WAN PPP connection More information about AT over IP will be given in the following chapter AT over IP The user device can use AT commands to get modem 3G module information and instruct the modem to perform some actions To use AT commands user device should open a TCP socket on port 12522 which is configurable through GUI and then send AT commands to this socket Only pre defined AT commands are supported Please refer to the Maxon Intelimax user manual for the custom AT command format and which commands are currently supported There are several commands that are not needed when the Intelimax is in PPP server mode such as Intelimax User Manual ATD or ATDT AT IPCTOS AT IPCTCS AT TCPDEL ATH ATO All socket related commands are not supported because when the Intelimax works in PPP server mode the TCP UDP socket on the WAN side is no longer needed the modem now is a gateway PPP Dialing Modes Modem Configuration Status WAN Scheduler Serial IP Stack Emulation Enable DOE MSChat lt E No Dial 0 0 0 Modem Emul VJ E i CLIENT CLIENTSERVER Forward Save Config to Modem LoadFromModem Reboot modem Three Dial modes are supported s MS Chat s No Dial e Modem Emulation The MS Chat Dial mode is to support
49. ode in server mode please leave this field as default Secondary Server Define the IP Address or DNS name of the secondary server the Intelimax will try to connect to in Client mode in server mode please leave this field as default Port Number Define the TCP or UDP Port number this port will be used in the server and client mode IP STACK Notifications IP Stack notifications are by default sent out on the serial port to the connected host With some applications this may cause issues with data transfer and using this option the user can disable or enable the notification messages Idle Timeout Idle Timer Enabling the idle Timeout and setting an Idle Timer will set the Intelimax to disconnect from a connected server if configured as a client or the connection from a connected client if configured as a server if the modem receives no data for the defined Idle Time period Bear in mind that data could be continuously sent from the modem to the connected device but if nothing is received back the modem will disconnect If the modem is connected as an auto connect client then it will try to reconnect to the server once it has disconnected Intelimax User Manual TCP Connect Message The TCP connect message function allows for sending either a custom string or the IMEI number over the socket connection when it is established If the field is left blank then the IMEI number of the modem will be sent otherwise the custom
50. on list must have already enabled emulation at emul EMUL 1 3 0 01044204412 192 168 101 2 3000 1 01044204411 192 168 101 2 30001 2 01044204414 10 0 0 1 5000 OK To Enable Disable Modem Emulation this must be enabled on the server Intelimax for CONNECT message at emul 0 0 disable at emul 0 1 enable To delete a rule from the list at emul 2 list_number e g at emul 2 I OK at emul EMUL 1 2 0 01044204412 192 168 101 2 3000 1 01044204414 211 232 22 1 500001 OK Intelimax User Manual Modmax Compatibility Mode This changes the IP Stack responses from Intelimax style responses to Modmax style responses AT SPC2 SPC lt mode gt OK lt mode gt O Intelimax mode 1 Modmax mode Default AT SPC lt passcode gt SPC lt mode gt OK lt passcode gt 857653 mode 0 356758 mode Intelimax Mode Modmax Mode TCP_Connect_To 125 181 12 34 18 57 55 28 JAN 2014 TCP_Connect_To 01 24 2014 08 00 36 192 168 10 50 01 24 2014 08 05 36 08 31 12 24 JAN 2014 TCP conneciion Connection_Close_By_Timed_Out disconnected Intelimax User Manual TCP Delay between trying to connect socket and CONNECT messages Some older systems working with the Modmax cannot handle the speed between messages this delay allows for these legacy systems to handle this delay AT TCPDEL 2 TCPDEL X Delay between try and connect range from 200 to 1000 mili second
51. or logging and uploading serial streams of data A new line in the file is created each second and a timestamp can either be enabled or disabled Intelimax User Manual In order to use FTP on the Intelimax please enable append on your FTP server Also restrict the welcome message to less than 10 characters Please save and apply settings before using To enable FTP on the Intelimax you can use either AT commands or the GUI the AT commands are covered in the AT command section at the end of the manual The FTP settings are on the IP Stack tab of the GUI Manual Hourly 0 24 Time of day 0 24 Here you can configure whether to upload the FTP files manually hourly 0 24 number of hours between uploads by time of day 0 24 where 1 is 1AM and 13 is 1PM by day of month 1 31 for day of month or by number of minutes passed 0 60 number of minutes between uploads The time interval field is used to configure the variable applicable to each of these modes NOTE when using Hourly and Minutes setting using a time interval of 0 means never upload automatically z FTP Server 192 168 10 1 FTP Port Number 21 Username admin Password admin File Name DHMAX File Size bytes 1000 Time Interval 9 Time Stamp The FIP server FIP port number FIP server username and password can all be configured here e FTP Sever Host IP Domain address with Port e User name Intelimax User Manual Password Time
52. ort configuration With certain applications there may be a need to fabricate a custom serial cable to work between the host and the Intelimax The custom serial cable depends on the equipment requirements and settings Serial Password Password protected AT commands The Intelimax has the ability to password protect serial interface AT commands The serial password can be set on the serial tab If AT commands need to be entered then AT commands will return an ERROR message until the interface password is entered first with the command AT PWD lt password gt Once the password is entered the access will persist for the session until the modem reboots Further AT command detail in the AT Command Password Protection section under the Intelimax specific AT Commands section Boot up Message The Intelimax boot up message INTELIMAX READY is a message that the modem sends to the host via serial port upon boot up Using this option the user can disable or enable this message Intelimax User Manual IP Stack Configuration IP stack configuration page is used to setup modem IP STACK settings such as port number and IP address and connection timeouts Modem Configuration Status WAN Scheduler Serial IP Stack Emulation DDNS admin System Protocol Mode Primary Server Secondary Server Port Number IP STACK Notifications Idle Timeout Idle Timer Network Dormant Period Keep Alive Wake U
53. ort number The client mode also supports a secondary server IP address just in case the primary server cannot be reached The in built IP stack feature supports smarts such as PPP link check TCP link check PPP link timeout TCP link timeout and MTU settings Secure socket using SSLv3 can be used in both these modes as well as IP Stack Manual Mode Further detail on how to configure secure socket is in the IP Stack tab section IP Stack Manual Mode With IPStack manual mode the modem doesn t initiate the PPP connection The modem will rely on the host on serial port to send the PPP initiation commands and acquire a WAN IP connection The AT command to start the PPP session and open a socket is AT IPCTOS The AT command to close the socket and PPP session is AT IPCTCS Further AT command detail is included at the end of this manual Serial Modem Mode Transparent Pass through This mode allows for the serial interface to connect through to the 3G module in the modem In this mode the Intelimax processor still has some control and processing abilities over the serial AT Commands and connection processes Used for PPP pass through or Circuit Switched Data CSD Intelimax User Manual Circuit Switch Data Call Circuit switch is a legacy style of communication where the user dials in to the modem data terminating number Standard set of AT commands used with Circuit Switch Call ATD Dial the Data number ATA Answer the Data
54. otify NO CARRIER Periodic Reset at preset 2 OK at presete PRESET 2 Getting SO value in serial modem mode Please use ATSO Command to get the SO value AT amp Y command will give you incorrect SO Value ATSO 2 OK ATSO 2 OK Single AT command SMS AT MMC SMSMO AT MMC SMSMO lt Phone number gt lt message gt lt CR gt Eg AT MMC SMSMO 0400123456 Boiler Temperature Too High lt CR gt Maximum length of message is 160 characters Some characters are not supported 4 gt 94 Intelimax User Manual Prepare modem for hard shutdown This function is highly recommended when using the modem with an external controlled power supply If the modem is going to have its power dropped regularly this AT command allows for the processor to perform housekeeping duties to ensure that the shutdown process does not damage the modem or internal cellular module AT RTD OK SMS on Boot The Intelimax can be configured to send an SMS at boot time using the following AT commands at pwronsms 2 PWRONSMS 1 0 1 enable disable PWRONSMS 2 1 2 3 Phone Number up to 3 phone numbers PWRONSMS 3 Message
55. p FTP FTP Server 192 168 10 1 FTP Port Number 21 Username admin Password admin File Name DHMAX File Size bytes 1000 Time Interval 0 Time Stamp Disable Protocol IP Stack supports TCP and UDP depending on your application requirement you can choose between TCP and UDP communication SSLv3 If the SSLv3 check box is ticked the Intelimax TCP IP to serial converter applies asymmetric cryptography to the socket connection using SSLv3 When using SSLv3 all serial data transferred is encrypted in both client and server modes Intelimax User Manual The SSLv3 certificates can be installed using the partial upload function in the GUI using the following process 1 Create the ceriification file for upload to the Intelimax The certificate files should be placed into a folder along with a path txt file _ cert pem _ key pem path bt The path txt file should only contain the text extra S pathos 1 extr Zip this folder then upload to the Intelimax using the Partial upload button in the GUI then reboot the modem Once the modem has rebooted the uploaded certificates can be seen on the status page under the Extra section Note To remove the certificates upload a zip file with one file a path txt file with the text extra path bt 1 extra Note If both SSLv3 IP Stack and secure syslog is used at the same tim
56. pitals and any other place where medical equipment may be in use Respect restrictions on the use of radio equipment in fuel depots chemical plants or in areas of blasting operations There may be a hazard associated with the operation of your Modem in the vicinity of inadequately protected personal medical devices such as hearing aids and pacemakers Please consult the manufacturers of the medical device to determine if it is adequately protected Operation of the Modem in the vicinity of other electronic equipment may cause interference if the equipment is inadequately protected Observe any warning signs and manufacturers recommendations The modem contains sensitive electronic circuitry Do not expose the modem to any liquids high temperatures or shock The modem is not waterproof Please keep it dry and store it in a cool dry place Only use original accessories or accessories that are authorized by the manufacturer Using unauthorized accessories may affect your modem s performance damage your modem and violate related national regulations Always handle the modem with care There are no user serviceable parts inside the modem Unauthorised dismantling or repair of the modem will void the warranty The product needs to be supplied by a limited power source or the power supply provided Otherwise safety will not be ensured Intelimax User Manual Vehicle Safety Do not use the modem while driving Respect national r
57. r Password Key Input Password for logging onto a DDNS server Modem Configuration Status WAN Scheduler Serial IP Stack Emulation DONS Admin System Enable DDNS DynDNS Service Provider dyn com Domain Name intelimax dyndns biz User Name Email user Password Key Intelimax User Manual PPP Server Usually the Intelimax acts as an IP connected cellular serial server relaying data between its serial inputs to TCP UDP sockets Devices connect to serial port of Intelimax directly send data or use dial commands to set up a data transmission session Some devices may need to use their own TCP IP stack in which case either serial modem mode transparent or PPP server can be used The benefit of using PPP server over serial modem or transparent mode is that the modem functionality can continue to be used and it will be uniquely addressed within the system This allows for the use of AT over IP for sending and receiving SMS messages or querying the signal strength SNMP for remotely monitoring the status of the modem or remote firmware upgrades to the modem if required PPP or Point to Point Protocol is a protocol commonly used to establish a direct connection between two devices over a serial cable phone line trunk line cellular telephone specialized radio links or fibre optic links Gateway i LAN PPP Conn 3G connection In this working mode the Intelimax will launch a PPP serv
58. re than 20 seconds 5 second hold is for profile reset 2 Why does the Intelimax GUI not connect and reports The attempt to connect was forcefully rejected If the Intelimax GUI connection to the modem is not closed with a TCP disconnect the modem may reject connections and report with a message The attempt to connect was forcefully rejected This occurs until the modem TCP timeout occurs which will be either via a modem reboot or after at least 10 minutes If the connection is local you can shorten this time by reconnecting the USB interface or under network connections selecting the LAN interface to the modem disabling then enabling this interface 3 Why does the Intelimax GUI show that the device is discovered but not connect The LAN interface to the modem needs to be configured correctly This may involve setting a static IP address to the modem such as 192 168 10 50 or removing an incorrect address The GUI will continue to try to connect to the modem 3 times after the Open button is pressed 4 Why is the GUI not detecting the Intelimax The Intelimax must be powered via the RJ45 connector then the USB plugged in after approximately 1 minute the PC will prompt for drivers to be installed The Intelimax requires the USB LAN interface drivers installed to be able to talk via a TCP IP connection to the modem which can be downloaded from the Maxon website There are times where the RNDIS network interface is presen
59. revious Save Activate Read Community Name Write Community Name System Name System Contact System Location M Main P Previous Save Q Quit Disable public private DHAGENT support maxon com au AUS 2 ja Telnet 123 209 44 193 M Main P Previous Save First Trap Server IP 192 168 080 200 Second Trap Server IP 192 168 6 262 Third Trap Server IP 192 168 080 202 P Previous Save M Main P Previous Save Q Quit Activate Disable Server Address z time nist gov Daylight Saving Disable Time Zone 8 8 M Main P Previous Save 73 ja Telnet 123 209 44 193 none login admin Password for help help setup at upt ime reboot exit INTELIMAR at usage at attcreg INTELIMAX i at at creg GREG 2 1 151 D81CA8 OK INTELIMAR m To check signal strength use at attcsq command Refer to the screen shot below ST Telnet 123 209 44 193 M Main P Previous SzSave Q Quit INTELIMAR usage at attcreg INTELIMAX at at csq CSQ 24 99 OK INTELIMA 74 ping uptime reboot usage ping ipaddress INTELIMAX ping 262 191 62 239 PING 262 191 62 239 282 191 62 239 gt 56 data bytes from 2682 191 62 239 icmp_seq f tt1 53 time 448 3 ms from 282 191 62 239 icmp_seq 1 tt1 53 time 433 8 ms from 262 191 62 239 icmp_seq 2 tt1 53 time 457 6 ms 282 191 62 239 ping statistics
60. ring client and server IP address a Telnet 123 209 44 193 M Main PzPrevious SzSave Q Quit 18 Operating Mode Username Password Dialup WAN Scheduler WAN Sch DUR cycle time WAN Sch DUR Power up time P Previous S Save IPStack Auto kokakakakaj e9 9 it telstra extranet Disable Disable M Main P Previous Save Q Quit CO JOY H hwy 9 16 11 12 Scheduler Scheduler Scheduler Scheduler Scheduler Scheduler Scheduler Scheduler Scheduler Scheduler Scheduler Scheduler GO GSS ERALAR 9 8 JEJ X Y G G GGG GGG CIELE 09 TE TEL TE TRL JE GO G G GGG JJ GOGO G X Y Y M Main P Previous Save Q Quit 70 fa Telnet 123 209 44 193 M Main P Previous Save Q Quit Baudrate 115288 Data bits S 8 Parity None Stop bits 1 Flow control None P Previous Save M Main P Previous Save Q Quit IPStack Sock Mode Server Notify Boot MSG Enable Notify IPs MSG Enable IPStack Protocol TCP IPStack IP1 4 6 6 6 IPStack IP2 4 6 6 6 IPStack Port 36668 TCP UDP Idle Timeout Enable TCP UDP Idle Timeout Timer 300 16 Custom PING Disable 11 PING Dest 1 4 6 6 8 12 PING Dest 2 GO IJ DY UT AWN o M Main P Previous S Save Q Quit afl ja Telnet 123 209 44 193 M Main P Previous S Save General Trap M Main P Previous Save Q Quit Q Quit M Main P P
61. rval 0 1 100 LCP Echo Failure OK Intelimax User Manual Periodic reset ATSSRESET 24 RESET 24 OK Parameters RESET X 0 24 Hours of Periodic reset WAN scheduler ATSSWANSS WANSS 0 Disabled OK Parameters WANSS 0 1 RS232 line driver power down 0 1 2 Disable Day of Week Duration 0 1 Delete Add schedule 5 59 Minutes of power up 0 28 Entry number of day of week Delete 0 1 2 3 4 5 6 Day of week Ddd 5 59 Minutes of power cycle 0 23 Hours of start 0 59 Minutes of start 0 23 Hours of finish 0 59 Minutes of finish 0 1 Engine power down OK IP Stack setting ATSSWANSI WANSI 1 1 1 0 0 0 0 0 0 0 0 0 30000 1 300 20 0 0 OK Parameters WANSI X X X X X X X X X X X X 0 1 2 None Server Client Intelimax User Manual 0 1 Disable Enable Notify Boot Message 0 1 Disable Enable Notify IPStack Message 0 1 TCP UDP XXX XXX XXX XXX Primary IPAddress XXX XXX XXX XXX Secondary IPAddress 0 65535 Port Number 0 1 Disable Enable Keep Alive 1 3600 Seconds Keep Alive Interval 5 60 Seconds Network Dormant Period UDP 0 1 Disable Enable UDP Keep Alive 0 1 2 60 Disable Handshake Seconds UDP Wake Up OK SNMP ATSSSNMPS SNMPS Disable public private DHAGENT supportamaxon com au AUS 192 168 0 200 192 168 0 2 01 192 168 0 202 OK Parameters SNMPS X X X X X X X X X 0 1 Disable Enable Read community Write community Name Contact Location Trap 1 IP address Trap 2
62. s OK AT TCPDEL 200 OK AT TCPDEL TCPDEL 200 OK Prepare modem for hard shutdown This function is highly recommended when using the modem with an external controlled power supply If the modem is going to have its power dropped regularly this AT command allows for the processor to perform housekeeping duties to ensure that the shutdown process does not damage the modem or internal cellular module AT RTD OK SMS on Boot The Intelimax can be configured to send an SMS at boot time using the following AT commands at pwronsms lt 2 PWRONSMS 1 0 1 enable disable PWRONSMS 2 1 2 3 Phone Number up to 3 phone numbers PWRONSMS 3 Message Intelimax User Manual Extended Module Specific AT Command Set Serial Modem Mode AT amp W Saves AT commands AT RESET 1 Serial Modem mode Applies saved AT commands with a reboot Parameter Description EO Do not echo command set in command state or online command state Echo command set in command state or online command state Q0 Return result codes Q1 Do not return result codes Circuit 109 CF always ON Circuit 109 CF ON in accordance with the specified service DCD line is High during a circuit switched call Circuit 109 CF ON DCD is always high This line toggles low for 1 second when the circuit switched call is disconnected Circuit 109 CF ON DCD is Low High when modem has successfully established a PPP Data packet switched call onl
63. s u GSM CS UL 9 6 Kbps DL 9 6 Kbps Environmental Specifications Normal Operation Temperature 20 to 70 C Extreme Operation Temperature 25 to 75 C Dimensions 71mm x 55mm x 26mm without side brackets and antenna Connections RJ45 Connection USB Connection SIM Card Holder Antenna connector FME male Mounting SIde mounting brackets LED Lights Power RSSI Data Module Approvals GCF PTCRB CE FCC ACA Carrier Approvals Please contact Maxon Australia for more information 13 Intelimax User Manual Modem Approvals ACA Compliance RoHS Compliant Power Source DC Input Voltage Range 6 to 32 VDC Idle Current 12V 5S0mA Maximum Current 12V 150mA Operating Systems Windows XP Vista 7 Intelimax User Manual Hardware compatibility Intelimax hardware from October 2014 has been updated with a new flash memory die which is not compatible with older firmware revisions Intelimax modems with this memory die are clearly marked with an E noting this change Any modem with this E marking can be used with firmware versions 2 0 x onwards If older firmware versions are loaded onto these modems will not run and will have to be returned to Maxon Australia for recovery Intelimax Firmware Upgrade paths for E die Older Firmware New Firmware Intelimax User Manual Intelimax Setup Maxon Intelimax serial modem supports a Winodws GUI wher
64. showing the signal level in dBm which should be better than 93dBm Trigger a connection through the modem either CSD or PPP connection and ensure that the data light will correctly flash to indicate data transfer through modem 3 In IP Stack auto mode a Connect to modem with GUI via USB interface and check the registration and signal strength of the modem The status page will snow whether the modem is currently registered as well as showing the signal level in dBm good levels are better than 81 dBm Ensure that the modem has a data connection which should be automatically set up by the IP auto modem connection function If the data LED is flashing then this connection has been established Remote Connection Checking In order to verify that the modem is correctly operating when the modem is remotely located please follow the below steps 1 In serial modem mode with CSD connection dial into the modem data number a b If the response is BUSY then the SIM card is not correctly provisioned If the response is NO CARRIER immediately then the SIM card is off line and not registered If the response is NO CARRIER after some time then the modem auto answer is not working correctly but the SIM card is registered If you are able to connect to the modem response is CONNECT then you can remotely check the settings on the modem by changing to an IP mode and making a connection to the mode
65. t under network connections but not when checked via a command line ipconfig If this is the case then the PC must be restarted as the Microsoft Windows RNDIS driver is not functioning correctly Intelimax User Manual Modem Configuration Modem Status Tab The modem status page displays modem information such as network registration and WAN connectivity status Modem Configuration Status WAN Scheduler Serial IP Stack Emulation DDNS Admin System Up Time Oday Oh 27m 2s System Time 2014 10 09 16 37 47 IMEI 354283049079 142 Version 2 1 1 201410021625 H W Version 1 8 Module Version 11 810 10 10 00 Network Registration Telstra Local network registered Network Band WCDMA PIN Status PIN request deactivated Area Information LAI 50501 LAC 151 CellID 00ea 1ca8 RSCP 66dBm ECIO 12 0dB Signal Level 67 dBm Mode IPStack Auto Server Status Listening WAN IP 10 100 189 127 Sent Packets 1KBytes Received Packets 1KBytes Information displayed on the Status page is F W Revision Firmware version output Includes version and compile date Ex 0 0 0 201201061408 H W Version Product s board release version Module F W Revision Engine s firmware version LAI LAC Cell ID IMEI IMEI number of the Intelimax WAN IP IP address assigned by ISP such as Telstra or Op us Signal Status of current signal strength dBm IP Stack Mode IP Stack Mode of In
66. telimax IP Stack Auto or Manual PIN Status Status of PIN request enable disable System Time System time acquired 3G network 50 Intelimax User Manual WAN Configuration WAN configuration page is used to configure how the modem will connect to the 3G network Please select the correct operation mode as this will decide if the modem will automatically connect to the network on power up or work in pass through mode The Intelimax supports 6 operation modes Ik IP Stack Auto mode Modem connects to the 3G networks and acquires an IP address and then runs the IP STACK server or client mode IP Stack Manual mode Modem wait for user to send AT commands before connecting to the 3G networks and acquiring an IP address Serial mode Pass through Transparent Connects to the 3G module in the modem Used for PPP pass through or Circuit Switched Data CSD PPP WAN Auto mode Modem is a PPP server over serial with the WAN IP connection automatically connected PPP WAN Conditional mode Modem acts as PPP server with the WAN IP connection conditional on the serial PPP connection PPP WAN Manual mode Modem acts as PPP server and the WAN IP connection can be controlled via AT over IP commands Modem Configuration Status WAN Scheduler Serial IP Stack Emulation DDNS Admin System Mode APN Dialup Auto Pin Username LCP Echo Interval 20 v Seconds Password Authentication
67. uld be more than one file generated each file should not exceed 10K bytes all these files will be sent to FTP server when time comes File uploaded with date time stamp disabled AT CSQ 36 Intelimax User Manual AT CSQ AT CSQ AT CSQ AT CSQ AT CSQ File uploaded with date time stamp enabled 09 11 2012 15 44 05 AT CSQ 09 11 2012 15 44 06 AT CSQ 09 11 2012 15 44 07 AT CSQ 09 11 2012 15 44 08 AT CSQ 09 11 2012 15 44 09 AT CSQ 09 11 2012 15 44 10 AT CSQ 09 11 2012 15 44 11 AT CSQ 09 11 2012 15 44 12 AT CSQ 09 11 2012 15 44 13 AT CSQ 09 11 2012 15 44 14 AT CSQ 09 11 2012 15 44 15 AT CSQ In manual mode AT commands can be used to prompt the modem to upload the files the AT commands themselves will also be included in the csv file ATSSFTPFL Displays the files waiting to be uploaded AT FTPSC Will start the FTP connection and upload the files This command can also be used to force an upload when in periodic mode If no WAN connection is currently established such as in IP Stack Manual mode the Intelimax will establish the PPP and socket conneciions upload the FTP files then drop the socket and PPP connections Intelimax User Manual Modem Emulation TAB Description Modem emulation assists in the transition from Circuit Switched Data CSD to Packet Switched Data IP PSD If the control centre management system supports IP but the field devices only support dialling back to the control centre using CSD
68. y applies to IP STACK Circuit 109 CF ON DCD is Low High when modem has successfully established a PPP Data and opened a socket with remote server packet switched call only applies to IP STACK Ignore circuit 108 2 CD Enter online command state following ON to OFF transition of circuit 108 2 See service specific AT command processing for service state transitions Enter command state following On to Off transition of circuit 108 2 See service specific AT command processing for service state processing requirements Automatic answering Enable automatic 1 to 255 S 0 SETS after Value 1 x 6 seconds 0 Not Answer ET Intelimax User Manual Command TE2 MT2 Command TE2 MT2 ATD lt phone_number gt CONNECT Data call connected Notify TE2 MI2 Connect lt Speed gt if connect_baud is set NO CARRIER Data call failure phone_number for Packet Switched Data 99 Australia requires authentication for Circuit Switched Data You will need a data number Code 2620 activated on the SIM account Notify TE2 MI2 AT RING Command TE2 gt MI2_ ATA answer data call CONNECT Data call connected Notify TE2 MI2 CONNECT lt SPEED gt if connect_baud is enabled NO CARRIER Data call failure Call State Command escape command to go to off line command state ATH release call N

Intelimax User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents