LMX9838 Bluetooth Qualification Guideline
Contents
1. LMX9838 Bluetooth PRD 2 0 Qualification Guideline 1 0 Introduction The National Semiconductor LMX9838Bluetooth Serial Port module is a highly integrated module including radio base band controller memory device crystal antenna and loop filter and internal EEPROM All hardware and the on chip ROM firmware is included to provide a complete solution from antenna through the complete lower and upper layers of the Bluetooth stack up to the application including the Generic Access Profile GAP the Service Discovery Application Pro file SDAP and the Serial Port Profile SPP National Semiconductor Application Note 1709 Markus Roemer September 2007 This document describes some qualification guidelines of the LMX9838 module based on the PRD 2 0 specification For more detailed information consult the www bluetooth org website All numbers screenshots and links are based on the blue tooth SIG website as of September 2007 and are subject to change 2 0 Using the LMX9838 as SPP module If the end product requires the SPP profile only e g Typical cable replacement application the LMX9838 module can be integrated as is into the end product 2 1 TO BE DONE List of the qualification requirements for using the LMX9838 as SPP module e The End Product Manufacturer must be signed up as a Bluetooth SIG Adopter This is free of charge See Section 4 1 BLUETOOTH MEMBERSHIP REGISTRATION e Perform End Product Listing2. EPL This is a free listing See Section 4 4 on page 4 for details 2 2 NOT REQUIRED The following point is not required for this specific system e Qualified Design Listing QDL not required The LMX9838 is already QDL listed as an SPP module By relabeling the End Product can refer to the LMX9838 QD ID 2 3 PRODUCT INFORMATION The product can be characterized by the following entries TABLE 1 End Product Information Design Information Product Name End Product Name Bluetooth Qualified Design ID QD ID B012394 Bluetooth Product Type End Product Product Name LMX9838 3 0 Implementing Additional Profiles on the LMX9838 If the end product requires additional profile s implemented on the host device e g Headset OBEX a few more quali fication requirements will be required for the end product 3 1 TO BE DONE List of the qualification requirements e The End Product Manufacturer must be signed up as a Bluetooth SIG Adopter This is free of charge See Section 4 1 BLUETOOTH MEMBERSHIP REGISTRATION e Perform additional profile s Qualification and Tests Price will depend on the Bluetooth Qualification Tests Facility The qualification and tests needed should be lowered to a minimum as the LMX9838 is already SPP module qualified e Use the Bluetooth test plan generator as described Section 4 2 BLUETOOTH TEST PLAN GENERATOR to define the required tests e QDL listing 10000 for Adopter See Section 4 3 QUA
3. distance between the equipment and the receiver e Connect the equipment to outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Any changes or modifications not expressly approved by the party responsible for compliance could void the user s au thority to operate the equipment Caution Exposure to Radio Frequency Radiation This device must not be co located or operating in conjunction with any other antenna or transmitter b Canada Industry Canada IC This device complies with RSS 210 of Industry Canada Op eration is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of this device L utilisation de ce dispositif est autoris e seulement aux conditions suivantes 1 il ne doit pas produire d interference et 2 l utilisateur du dispositif doit tre pr t accepter toute interference radio lectrique regu m me si celle ci est sus ceptible de compromettre le fonctionnement du dispositif Caution Exposure to Radio Frequency Radiation The installer of this radio equipment must ensure that the an tenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population consult Safety Code 6 obtainable from Health Canada s web site h
4. LIFICATION LISTING INTERFACE for how to obtain a new QD ID and details on the Qualification Listing Interface QLI Bluetooth is a registered trademark of Bluetooth SIG Inc and is used under license by National Semiconductor Corporation 2007 National Semiconductor Corporation 300370 www national com SUI EPINS uoespeno 0 GHd YIOOJ NIG 8E86XNT 60Z1 NV AN 1709 4 0 References All references are based on the Bluetooth SIG website as of September 2007 and are subject to change Refer to qualweb bluetooth org as a general link to the Bluetooth Qualification Program 4 1 BLUETOOTH MEMBERSHIP REGISTRATION To become member of the Bluetooth SIG go on the following link https programs bluetooth org login register Fill in the required information of the following form and send Bluetooth op Bluetooth com search site enter keywords here search gt Membership Registration Thank you for your interest in becoming a member of the Bluetooth Special Interest Group SIG Membership within the Bluetooth SIG is reserved at the company level however employees of companies are also encouraged to register as users associated with their member company As a member of the Bluetooth SIG your company will join thousands of companies who share a common interest building and promoting devices that incorporate Bluetooth wireless technology To register your company for membership please select the Adopter Mem
5. RELATING TO FITNESS FOR A PARTICULAR PURPOSE MERCHANTABILITY OR INFRINGEMENT OF ANY PATENT COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT LIFE SUPPORT POLICY NATIONAL S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION As used herein Life support devices or systems are devices which a are intended for surgical implant into the body or b support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation All other brand or product names may be trademarks or registered trademarks of their respective holders Copyright 2007 National Semiconductor Corporation For the most current product information visit us at www national com National Semiconductor National Semiconductor Europe National Semiconductor Asia National Semiconductor Japan Americas Customer Customer Support Center Pac
6. abeled with Contains TX IC 1520A LMX9838 or Contains transmitter module IC 1520A LMX9838 5 1 1 3 End Product Manual Information In the user manual final system integrator must ensure that there is no instruction provided in the user manual to install or remove the transmitter module LMX9838 must be installed and used in strict accordance with the manufacturer s instructions as described in the user doc umentation that comes with the product The following information is required to be incorporated in the user manual of final system a USA Federal Communications Commission FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable pro tection against harmful interference in a residential installa tion This equipment generates uses and can radiate radio frequency energy If not installed and used in accordance with the instructions it may cause harmful interference to radio communications However there is no guarantee that inter ference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by tuning the equipment off and on the user is encouraged to try and cor rect the interference by one or more of the following mea sures e Reorient or relocate the receiving antenna e Increase the
7. ber option below If your company is interested in Associate membership please send an email to member relations bluetooth com after you have registered your company for Adopter membership If you are an employee of a company thatis already a member and would like to register as a user please select the Existing Member option below m Please choose your registration option Adopter Member Adopter membership is a free level of mernbership All new companies must register as an Adopter member first If your company is interested in upgrading to Associate membership please email member relations bluetooth com after you have completed Adopter membership registration View the benefits of Associate mernbership Choose Adopter Membership Existing Member Ifyou are an employee of a current member company please select this option As an employee of an existing mernber company you will automatically be associated with your company s membership and have the opportunity to further get involved with Bluetooth wireless technology C New User from a Member Company m Aboutyou Indicates required field First Name l Y Middle Initial S S Last Name a Company L Job Title es Mobile Email O erify Email el Universities Students Education Atthis time students and universities are not eligible for membership within the Bluetooth SIG If you are looking for inforrnation on Bivetooth wir
8. de feedback on this new search Y Simple Search Search B012394 Search In M Qualified Products List QPL PRD 1 0 M Qualified Design List DL PRD 2 0 M End Product List EPL Rows Per Page 59 Search Reset Advanced Search gt Number of found item s per list PRD 1 0 0 PRD 2 0 1 EPL 2 Total Records Found 3 Create New EPL PRD 2 0 68012394 LMX9838 LMX9838 National End Product 29 Jan 2007 EPL s 2 Bluetooth Semiconductor Serial Port Module 30037003 www national com 4 4 3 QUALIFICATION LISTING INTERFACE Once a project is created the next point should be to follow the Qualification Listing Interface QLI steps to obtain a QD ID and proceed the qualification checklist All details are on the following link https programs bluetooth org tpg QLI_Landing cfm search site enter keywords here search gt Qualification Listing Interface QLI STEP 1 Select Project and Qualified Design Identifier QD ID to Qualify gt gt Click Here to Start the Qualification Listing Process gt gt Important Note There are two requirements to be fulfilled prior to starting the Qualification Listing Process These are 1 Before you can qualify and list your design you are required to obtain a QD ID The fee for a QD ID will be applied as a credit toward your full listing fee once you ve completed the qualification process Please note that you may choose to purchase just t
9. eless technology fora project please visit Learn Individual Users Not Associated with a Company The Bluetooth SIG does not accept individuals for membership As such ifyou are not associated with a valid company or if you are using a public email domain your membership will not be accepted If you are an individual looking for information on Bivetooth wireless technology please visit www bluetooth com If you have any questions in regard to potential membership within the Bluetooth SIG please email Member Relations 30037001 www national com 2 4 2 BLUETOOTH TEST PLAN GENERATOR To start a new test plan generator go on the link hitps programs bluetooth org tpg testplan cfm And follow the steps of the test plan search site enter keywords here search gt Create a Test Plan STEP 1 Create Select a Project Before you can generate a test plan you must Create a Project Projects contain general information about the design you are planning to qualify to and allow you to declare which features you plan on implementing To create a test plan from an existing project choose from your projects below to edit PICS documents PRD 2 0 Projects test3 Testproject2 Testproject STEP 2 Declaration Summary The declaration surnmary allows you to choose which layers you will be supporting STEP 3 Edit Core PICS The Core PICS consist of RF BB LMP L2CAP3 SDP and GAP For an End Pr
10. he QD ID or to purchase the full listing when purchasing the QD ID Click here to Obtain a OD ID 2 Before you can qualify and list your design you must also Upload your Test Declaration TDU Once the TDU has been uploaded for your project you can continue on with the Qualification Listing process STEP 2 Member Declarations Document In this step you will fill out the Design information as well as print and sign a copy of the Member Declarations Document STEP 3 Qualification Checklist This step requires that you check the box next to each item in the list and declare that you have complied with each abatam ant 30037004 5 www national com 602 L NV AN 1709 4 4 EPL LISTING To create an End Product Listing go on the following link once registered https programs bluetooth org tpg QLI_All_Designs cfm Find next the product to be listed as EPL To do so enter the QD ID number B012394 in the search field The LMX9838 module appears in the result field Click on Create New EPL Fill in the information required and send Bluetooth SIG Shop Bluetooth corn search site enter keywords here search gt Qualified Listings Note Please click on the label for heip on individual search criteria or oper this feip file for heip on aii search criteria Please provide feedback on this new search vy Simple Search Search 012304 Search In M Qualified Products List PL PRD 1 0 M Qualified Design Lis
11. ific Customer Support Center Customer Support Center Support Center Fax 49 0 180 530 85 86 Email ap support nsc com Fax 81 3 5639 7507 Email Email europe support nsc com Email jpn feedback nsc com new feedback nsc com Deutsch Tel 49 0 69 9508 6208 Tel 81 3 5639 7560 Tel 1 800 272 9959 English Tel 49 0 870 24 0 2171 Francais Tel 33 0 1 41 91 8790 www national com
12. oduct all mandatory requirements of these layers must be supported For a Host Sub system all mandatory requirernents of L2CAP SDP and GAP must be supported For a Controller Sub system all mandatory requirements of RF BB and LMP must be supported STEP 4 Edit Profile PICS Any profiles that your product contains can be edited here STEP 5 Consistency Check Before a correct test plan can be generated a static consistency check needs to be performed to ensure that the proper features are supported Many features have prerequistes dependencies or groupings that are required if they are supported STEP 6 Generate the Test Plan The Test Plan is the final step Here you are issued a report of all the test cases that need to be performed in order to qualify your project 30037002 3 www national com 60Z1 NV AN 1709 To create a new project the LMX9838 PICS information might be necessary To get those information go on the link https programs bluetooth org tpg QLI_All_Designs cfm Enter the QD ID number B012394 in the search field The LMX9838 module appears in the result field Click on profiles then display PICS details to get the PICS information needed Bluetooth SIG Shop Bluetooth corn search site enter keywords here search gt Qualified Listings Note Please click on the label for Reip on individual search criteria or oper this kolip file for heip on ali search criteria Please provi
13. t DL PRD 2 0 M End Product List EPL Rows Per Page 59 Search Reset Advanced Search gt Number of found item s per list PRD 1 0 0 PRD 2 0 1 EPL 2 Total Records Found 3 Create New EPL PRD 2 0 68012394 LMX9833 LMX9838 National End Product 29 Jan 2007 EPL s 2 Bluetooth Semiconductor Serial Port Module 30037005 www national com 6 5 0 Regulatory Compliance The LMX9838 has been tested and approved to be compliant to the following regulatory standards CE Compliance e EN 300 328 v1 7 1 e EN 301 489 17 v1 2 1 IC Compliance e RSS GEN Issue 1 e RSS 210 Issue 7 Annex 8 and RSS GEN issue 2 FCC Compliance e FCC Part 15 Subpart C 5 1 FCC INSTRUCTIONS 5 1 1 Safety Information For RF Exposure 5 1 1 1 FCC Radiation Exposure Statement This module may only be installed by the OEM or an OEM integrator The antenna used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter OEM integrators and End users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance Only the antenna filed under FCC ID ED9LMX9838 can be used with this device 5 1 1 2 End Product Labeling FCC ID label on the final system must be labeled with Contains TX FCC ID EDOLMX9838 or Contains transmitter module FCC ID ED9LMX9838 IC label on the final system must be l
14. ttp Awww hc sc gc ca rpb www national com 602 L NV LMX9838 Bluetooth PRD 2 0 Qualification Guideline AN 1709 Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION NATIONAL PRODUCTS NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE NO LICENSE WHETHER EXPRESS IMPLIED ARISING BY ESTOPPEL OR OTHERWISE TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL S PRODUCT WARRANTY EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS BUYERS SHOULD PROVIDE ADEQUATE DESIGN TESTING AND OPERATING SAFEGUARDS EXCEPT AS PROVIDED IN NATIONAL S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS NATIONAL ASSUMES NO LIABILITY WHATSOEVER AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES
Download Pdf Manuals
Related Search