Euro-Docsis 3.0 Wireless Cable Modem Gateway
Contents
1. N E T G E A R Installation Guide Euro Docsis 3 0 Wireless Cable Modem Gateway CG3300D Package Contents e Gateway e Power adapter e Vertical stand recommended e Ethernet cable e Installation Guide this guide Start Here Estimated installation time 15 to 30 minutes You will need a computer with DHCP enabled and an available Ethernet port Installation Follow these quick steps to install your gateway 1 For better wireless performance insert the gateway into the stand as shown ae ae ae a 2 Connect the gateway Use the coaxial cable provided by your cable company to connect the cable port A to your cable outlet wW v dL 4 4 Attach the power adapter cable to the gateway and plug it into an electrical outlet Make sure that the Power button on the rear panel is in the On position Power button After the gateway is connected and power is applied the gateway automatically attempts to do the following Scan and lock the downstream frequency and then link back in upstream direction Obtain an IP address for the gateway itself Then the gateway assigns an IP address for the connected PC Connect to the Internet 5 Wait about two minutes for the LEDs to stop blinking Then verify the following The Power LED is solid green The Downstream and Upstream LEDs are lit The Internet LED is solid green indicating a link has been established to the Interne2. c Code which provides guidelines for proper grounding of this device In particular section 820 93 specifies that the coaxial cable shield must be connected to the grounding system of the building as close to the point of cable entry as practical Warning When installing or realigning an outside antenna system take extreme care to avoid any contact with the power lines or circuits Contact with them could be fatal Reference to the Grounding Figure The numbers in the figure on the right indicate 1 Electric service equipment 2 Power service grounding electrode system NEC Art 250 Part H Ground clamps Grounding conductors NEC Section 810 21 Antenna discharge unit NEC Section 810 20 Ground clamp a Oe Ee Antenna lead in wire Do not stack or place near heat source Warning Do not install this device on top of any other electrical equipment or install any other equipment on top of this device Keep this device a away from any heat sources such as direct gt um sunlight heaters radiators or other A V N receivers or devices that emit heat Electrical and Electronic Equipment the WEEE Directive If disposed of within the European Union this product should be treated and recycled in accordance with the laws of your jurisdiction X This symbol was placed in accordance with the European Union Directive 2002 96 on the Waste m implementing the WEEE Directive 2009 by NETGEAR Inc All rights reserv
3. ed NETGEAR and the NETGEAR logo are registered trademarks of NETGEAR Inc in the United States and or other countries Other brand and product names are trademarks or registered trademarks of their respective holders Information is subject to change without notice WU Ce 201 11737 01 June 2009
4. f On Off Pushing this button opens a 2 minute window for the gateway to con nect with other WPS enabled devices For more information about Push N using WPS select Documentation from the main menu and then see Connect WPS the on line User Manual Troubleshooting e You can use the LEDs on the front of the gateway to determine the status of the gateway and your Internet connection If you cannot connect to the Internet view the LEDs to make sure that all connections are secure and power is supplied e There is a Power button on the rear panel of the gateway This button must be in the On position when the gateway is in use e You can return the gateway to its factory settings On the bottom of the gateway press and hold the Restore Factory Settings button l for over 7 seconds The gateway resets and returns to its factory settings Technical Support Thank you for choosing a NETGEAR product Please call your Cable Internet Service Provider for technical support You may also take advantage of NETGEAR technical support resources such as the NETGEAR online knowledge base at http kbserver netgear com Defective or damaged merchandise should be returned to your point of purchase representative This information supersedes all support information printed on any NETGEAR packaging or documentation Note to CATV System Installer Please call the CATV systems installer s attention to section 820 93 of the National Electri
5. t The LAN LED is lit that corresponds to the local Ethernet port where you connected your computer For more information see the LED table on the other side of this document e Solid green Power is supplied to the gateway e Solid amber Power has been cut off due to overheating Make sure Power the gateway s ventilation is not blocked When the gateway cools down power cycle the gateway Flashing amber New firmware is updating Off No power Solid green The gateway is synchronized and all four channels are W in use channel bonding Downstream Flashing The gateway is scanning for a downstream DOCSIS channel Off No downstream channels are locked Solid green The gateway is synchronized and all four channels are N in use channel bonding Upstream Flashing The gateway is ranging to set up an upstream channel Off No upstream channels have been established Solid green The gateway is online cL Flashing The gateway is establishing its link to the Internet W Green indicates 1 000 Mbps Amber indicates 10 100 Mbps Solid An Ethernet device is connected and powered on LAN Ethernet Flashing Data is being transmitted or received on the Ethernet port Off No Ethernet device is detected on the Ethernet port ee Turn the wireless radio in the gateway on and off The wireless radio is i gt on by default The LED located below this button indicates if the wire Wireless less radio is on or of
Download Pdf Manuals
Related Search