XPar 360 - PR Lighting
Contents
1. XPar 360 PR 8955 This product manual contains important information about the safe installation and use of this projector Please read and follow these instructions carefully and keep this manual in a safe place for future reference PR LIGHTING LTD http www pr lighting com INDEX SAFE USAGE OF THE PROJECTOR 3 INSTALLING THE PROJECTOR 4 CONTROL SYSTEM AND POWER CONNECTIONS 4 DMX TERMINATOR 5 SETUP OPTIONS PROJECTOR CONFIGURATION 5 TO SET THE DMX START ADDRESS 6 OPERATION MENU 7 DMX PROTOCOL 9 INDICATION OF LED DISPLAY 12 MAINTENANCE 12 TROUBLESHOOTING 12 TECHNICAL DATA 13 ELECTRICAL DIAGRAM 16 COMPONENT ORDER CODES 17 Please note that as part of our ongoing commitment to continuous product development specifications are subject to change without notice Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement The publishers cannot be held responsible for the accuracy of the information herein or any consequence arising from them Every unit is tested completely and packed properly by the manufacturer Please make sure the packing and or the unit are in good condition before installation and use Should there be any damage caused by transportation consult your dealer and do not use the unit Any damage caused by improper use will not be assumed by the manufacturer and or dealer ACCESSORIES These items are packed together with th2. 240 255 Speed 16 the slowest 9 17 Note Channel priority from high to low is as the following Dimming Preset memory User memory ARGBW dimming HSV dimming Macro channel Color temperature When high priority channel is used low priority channel is No effect 10 17 INDICATION OF LED CHARACTER On DMX signal OK Decimal point of the first character Off No DMX signal f On Master slave signal is OK Decimal point of the third character Of No master slave signal 3 On When setting master mode Decimal point of the fourth character Off When setting slave mode Parameters that LED characters display Flash Parameters not saved press ENTER to save them MAINTENANCE To prolong the life of the projector it is very important to do the maintenance work Cooling fans must be cleaned once every 15days and external lens cleaned periodically for an optimum light output DO NOT USE ANY SOLVENT CONTAINING CHEMICAL ELEMENT Cleaning frequency depends on the environment in which the fixture operates Soft cloth and typical glass cleaning products should be used for cleaning with care It is recommended to clean projector at least once every 20 days Do not use any organic solvent e g alcohol to clean housing of the apparatus TROUBLESHOOTING PROBLEM ACTION gt Power connection is not correct gt Power supply is damaged or abnormal Call a
3. selection 11 Saturation 000 255 Saturation from shallow to deep 12 Value 000 255 From dark to light 8 9 13 Strobe wi bial 001 255 Strobe speed from slow to fast 000 No effect 001 015 Preset memory 1 016 031 Preset memory 2 10 14 Preset memory 032 047 Preset memory 3 048 063 Preset memory 4 064 079 Preset memory 5 080 095 Preset memory 6 8 17 096 111 Preset memory 7 112 127 Preset memory 8 128 143 Preset memory 9 144 159 Preset memory 10 160 175 Preset memory 11 176 191 Preset memory 12 192 207 Preset memory 13 208 223 Preset memory 14 224 239 Preset memory 15 240 255 Preset memory 16 000 No effect 001 015 Usermemory 1 016 031 User memory 2 032 047 Usermemory 3 048 063 Usermemory 4 064 079 Usermemory 5 080 095 User memory 6 096 111 User memory 7 11 15 User Memory 112 127 User memory 8 128 143 User memory 9 144 159 User memory 10 160 175 User memory 11 176 191 User memory 12 192 207 User memory 13 208 223 User memory 14 224 239 User memory 15 240 255 User memory 16 001 015 Speed 1 the fastest 016 031 Speed 2 032 047 Speed3 048 063 Speed 4 064 079 506665 080 095 506666 096 111 Speed 7 112 127 Speed 8 12 16 Memory Speed 128 143 Speed 9 144 159 Speed 10 160 175 Speed 11 176 191 Speed 12 192 207 Speed 13 208 223 Speed14 224 239 Speed 15
4. FUNC UP DOWN ENTER Projector configuration can be set conveniently via push button switch and LED display Launch the projector and press button ENTER for more than 5 seconds to unlock the panel the LCD will show the function menu of the projector each main menu has its submenus and each submenu has a specific function For details please see the OPERATION MENU section UP or DOWN if you want to browse through the various Setup Options Press button ENTER to save your settings or enter the next menu Press button UP or DOWN to change values add or subtract Press button Press button FUNG it will return to the upper menu one by one or browse through the main menu 5 17 TO SET THE DMX START ADDRESS Each Xpar360must be given a DMX start address so that the correct projector responds to the correct control signals This DMX start address is the channel number from which the projector starts to listen to the digital control information being sent out from the controller The Xpar360 have 3 DMX modes which are standard mode extended mode and short mode For example the standard mode has 12 channels so set the No 1 projector s address 001 No 2 projector s address 13 No 3 projector s address 25 No 4 projector s address 37 and so on Launch the projector Press button ENTER for more than 5 seconds to unlock the panel Press button FUNC up or DOWN to find Ad
5. LED CONTROL BOARD 230060139 1 LED LAMP BOARD 230020283 1 15 17 16 17 PR LIGHTING LTD PR New Hi tech Science Park 1582 Xingye Avenue Nancun Panyu Guangzhou 511442 China TEL 86 20 3995 2888 FAX 86 20 3995 2330 P N 320020091 Version 20120717 17 17
6. channels 16 level speeds adjustable Self Test Mode OTHER FUNCTIONS LED board temperature display Fixture usage time display 12 17 Parameters about DMX mode Display setting status operation mode can be transmitted by synchronous control HOUSING High temperature ABS die casting aluminum IP20 WORK ENVIRONMENT TEMPERATURE 20 C 40 C WEIGHT 3 9kg SIZES LIGHT OUTPUT 28 lux KRGBWA 1775 444 197 111 71 49 ha CR 309 77 34 19 12 9 6 15 CS 777 194 86 49 31 22 ee le SB 26 6 3 2 1 1 2B UX CW 722 181 80 45 29 20 CA 124 31 14 8 5 3 7m 6m 5m 4m 3m 2m Om iu N 1m 2m 3m 4m 5m 6m 7m Distance m Om 5m 10m 15m 20m 25m 30m 28 Diameter m 20 2245 2491 07 36 29 81 21227 014 72 13 17 AdSevSre as TAXE OW SS se So Soo Se SEE oS s a A lt lt lt c lt o JL o S 53 Pa Sa Se m DIRS Ov Ss aw CD 5 gt gt m 10 DID KD Ne Ad e 200EeN d panog pa 14 17 COMPONENT ORDER CODES NAME PART NO QUANTITY REMARK LED LENS 070070047 60 15 SIGNAL CABLE 230090002 1 3meters POWER SUPPLY 190010119 1 150W58V DRIVER BOARD 230060115 1
7. dR menu Then press ENTER to show DMX address and press UP or DOWN to set DMX address At this time the address will flash continuously Press button ENTER to confirm and it means the setting has been enabled Press button FUNC it will return to the upper menu one by one 6 17 OPERATION MENU 1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL AddR XXX DMX address XXX 1 512 STd Standard mode dmX EXT DMX mode Extended mode SHRT Short mode ON 615 OFF CNFG Display settings Shut off digital CRT without Config settings pressing buttons in 5 minutes SLAV mORS Slave Master Slave Settings mAST Master FACT Reset factory setup yES TRmd ES Transmit parameters y TImE Fixture usage time INFO TEmP xx Information LED board temperature VER Version RAR A Amber R Red G TEST Blue Test mode B Blue W white ALLO Red green blue white dmx DMX mode PR XX Preset memory PRO1 PR16 COL1 XX mENU Colour 1 Number 0 14 3 Operation mode COL2 XX ET XX Colour 2 Number 0 14 User memory ET01 ET16 COL3 XX Colour 3 Number 0 14 COL4 XX Colour 4 Number 0 14 Note 1 ONLY one projector of a group connected by one signal cable could be set as Master When the Master functions DMX control signal should be disconnected 2 When mul
8. e master slave mode set the first fixture master the others salve slave is default As for power connections each projector has to be supplied separately by external power Use the power cord of each projector to connect the mains power directly paying attention to the voltage and frequency marked on the panel of the projector 4 17 All of the connections are as the figure below Power DMX Controller DMX OUT DMX IN DMX OUT DMX IN IN Power IN Power IN XLR terminator DMX TERMINATOR In the Controller mode at the last fixture in the chain the DMX output has to be connected with a DMX terminator This prevents electrical noise from disturbing and corrupting the DMX control signals The DMX terminator is simply an XLR connector with a 120Q ohm resistor connected across pins 2 and 3 which is then plugged into the output socket on the last projector in the chain The connections are illustrated below DMX TERMINATOR CONNECTION Connect a 120 OHM resistor 3 across pins 2 and 3 in an XLR plug 120Q and insert into the DMX out socket on the last unit in the chain SETUP OPTIONS PROJECTOR CONFIGURATION CM
9. e projector Name Quantity Unit Remark Barn door 1 Pc Optional Safety cord 1 Pc This manual 1 Pc Signal cable 1 Pc Optional 2 17 SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector Should there be any damage caused by transportation consult your dealer and do not use the apparatus The projector can be used indoors and outdoors IP20 The projector is not designed or intended to be mounted directly on to inflammable surfaces X The projector is only intended for installation operation and maintenance by qualified personnel Do not project the beam onto inflammable surfaces minimum distance is 5m 5m Avoid direct exposure to the light from the lamp The light is harmful to eyes Do not attempt to dismantle and or modify the projector in any way Electrical connection must only be carried out by qualified personnel Before installation ensure that the voltage and frequency of power supply match the power requirements of the projector It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards Do not connect this device to any other types of dimmer apparatus Make sure that the power cord is never crimped or damaged by sharp edges Never let the powercord come into contact with other cables Only handle the power cord by the
10. nd then hang the hook to a high place Eventually use the safety cord provided to pass through the handles and hang it as a second safety fixing CONTROL SYSTEM AND POWER CONNECTION DMX IN DMX OUT DMX512 1 2 2 1 PIN FUNCTION Ors 2 DATA 3 3 3 DATA Connection between the controller and a projector and between one projector and another must be made with a 2 core screened cable with each core having at least a 0 5mm diameter Please use the projector s cannon 3 pin signal input and output cables as connection The 3 pin signal connections are connected as shown in the figure above Note Care should be taken to ensure that none of the pins touch the metallic body of the plug or each other The body of the plug is not connected in any way The XPar 360 accepts digital control signals in protocol DMX512 1990 The amount of projectors connected in parallel is not more than 32 Connect the controller s output to the first fixture s input cable with a 3 pin signal cable connect the first fixture s output cable to the second fixture s input cable and connect the rest fixtures in the same way Eventually connect the last fixture s output cable to a DMX terminator Note Only when all the start addresses of fixtures are set the same synchronous control could be achieved When the first fixture is not connected to the controller and all the other connections are the same as above it is master slave mode connection To achiev
11. plug Never pull out the plug by tugging the power cord Keep the optical system clean Do not touch the LED lens with bare hands When the projector is hanged to a high place please use a safety cord provided to pass through the projector handles as a secondary safety fixing for safety seasons For details refer to INSTALL THE PROJECTOR section LED lens shall be changed if they have become visibly damaged to such an extent that their effectiveness is impaired SZ for example by cracks or deep scratches RI Exterior surface temperatures of the projector after 5 minutes operation is 45 C when achieving steady state it is50 C There is no user serviceable parts inside the projector do not open the housing and never operate the projector with the covers removed Always disconnect from the mains when the device is not in use or before cleaning it or before attempting any maintenance work If you have any questions don t hesitate to consult your dealer or manufacturer 3 17 INSTALL THE PROJECTOR Lamp Hook Mounting Hole Safety Cable Support When the projector is used as the right figure above unfold the support to certain angle and put the projector onto a flat surface Make sure it is steady When the projector is used at a high place as the left figure above fold the support turn it round to the top of the projector connect a lamp hook to the mounting hole reserved in the support by screws a
12. qualified personnel The projector doesn t switch on to fix it gt Connection of control board is not correct Call a qualified personnel to fix it The projector can be turned on butLEDs do gt Connection of LED board is not correct Call a qualified not emit light and are out of control personnel to fix it The lamp comes on but the projector gt Make sure that the projector is correctly configurated doesn t respond to the controller gt Replace or repair the DMX cable gt The projector is too hot Take ventilation measures to make it The beam appears dim cool 11 17 TECHNICAL DATA VOLTAGES 200V 220V 230V 240V AC 50 60Hz Optional 100V 120V AC 50 60Hz POWER CONSUMPTION 200W 220V LED Power consumption 3W Quantity 60 18R 13G 13B 12W 9A Manufacturers Rated LED Life 50000 Hours COLOURS RGBWA linear color mixing with Macro COLOR TEMPERATURE CORRECTION Linear color temperature correction from 3200K to 10000K DIMMER 0 100 linearly adjustable STROBE Electronic Strobe 0 25F P S LIGHT ANGLE Field Angle 1 10 Maximum 6 28 Beam Angle 1 2 Maximum 612 15 Lens Angle 15 Optional Lens Angle 8 25 45 CONTROL DMX512 3 pin interfaces 8 channels in short mode 12channels in standard mode and 16 channels in extended mode Master Salve Synchronous Control Mode 16 preset memories 16 user memories preset memories and user memories can be called by control
13. tiple projectors work together in synchronous control state Parameters can be transmitted from the master projector to the slave projectors such as DMX channel mode Display setting status and operation mode User memory data is included While data transmitted other projectors will be set as SLAVE 7 17 DMX PROTOCOL hese pan gid Pii FUNCTION DMX DESCRIPTION 1 1 1 Dimmer 000 255 Dimming from dark to light 2 Dimmer Fine 000 255 Dimmer in 16 Bit precision 000 No effect 2 2 3 Colour Temperature 001 255 Colour temperature linear adjustment from 3200K to 10000K 0 No effect 001 015 Colour Temperature 3200K 016 031 Colour Temperature 5600K 032 047 Colour Temperature 7200K 048 063 Colour Temperature 10000K 064 079 Amber 080 095 Red 096 111 Green 3 4 Macro Channel 112 127 Blue 128 143 White 144 159 Red amp Green Yellow 160 175 Green amp Blue Cyan 176 191 Red and Blue Purple 192 207 Red Green Blue and White 208 223 Full Power 224 239 Yellow and White 240 255 Amber Blue and White 3 4 5 Amber 000 255 Linear adjustment from dark to light 4 5 6 Red 000 255 Linear adjustment from dark to light 5 6 7 Green 000 255 Linear adjustment from dark to light 6 7 8 Blue 000 255 Linear adjustment from dark to light 7 8 9 White 000 255 Linear adjustment from dark to light 10 Hue 000 255 Hue
Download Pdf Manuals
Related Search