YN565EX II-佳能
Contents
1. L cd 7 15 30 The display time of LCD backlight is 7 15 30 seconds 57 DE NA M EON J m lm L J m KLN Fn NO E4 I nc 0 3 0 3ev for fine tuning step in manual flash output I nc 0 5 0 5ev for fine tuning step in manual flash output Inc on Mix 0 3EV and 0 5EV for fine tuning step in manual flash output Fn NO E5 CLEA Recover the default settings long press OK button can restore the default Settings 8 Use the External Charging Pack You can purchase the Yongnuo external charging pack SF 18C or SF 17C connect it to the charging port of the YN565EX II After the flicker shown the charging pack will charge the flash 9 High speed Continuous Shooting The flash supports the high speed continuous shooting function Please set the camera in the continuous shooting form and then shoot Please note The quantity of photos that can be continuous shot is related with the brightness setting Please use the fully charged battery 10 Reflection Flash Bounce flash means to take photos by making flash light head aimed at wall or ceiling and using the light reflected back from the ceiling or wall to light the desired object so that the shade behind the object can be decreased to get more natural shooting effect If the wall or ceiling is too far the bounce flash may be too weak to get enough exposure The wall or ceiling should be even and white in order to2. Warning To avoid fire or electrical shock do not expose this product to rain or moisture To avoid short circuit please sure the batteries contacts are securely packed and in accordance with local provisions when handling the battery Please place the batteries and the parts which can be swallowed mistakenly away from children Contact a doctor immediatelywhen it occurs To avoid possible injury to eyes do not use the flash light in a short distance from the eyes To avoid possible safety accident do not use the flash light on the people who need a high degree of attention Please take out the batteries and stop using immediately in case of below This product is dropped or shocked seriously and the inner part of the product is bared f the battery leaks corrosive liquids please take out the battery with gloves The product gives off strange smell heats or smokes Do not disassemble or maintain this product Touching the internal high voltage circuit will cause electric shock Please take out all the batteries if not use this product for a long time ll Features COMPATIBLE WITH N s and C s WIRELESS FLASHING SYSTEM One YN565EX II is able to accept the internal flashing of YN568EX II 580EX II SB 900 800 700 7D 60D 600D C order of N s internal flashing and wireless signal of ST E2 supports 4 channels achieves external TTL and manual flashing TTL FLASH WITH HIGH GUIDE NUMBER GN58 1ISO100 105mm supports TTL M MUL
3. You can create two or three slave groups to make better shooting effect to meet your requirements 1 Wireless flash of two slave units made up by YN565ExX II e Wireless option setting Sc Sn for operation Communication Channel setting 1 2 3 4 Groups setting Set one YN565EX II as group A and set the other one as group B Master unit setting Set the communication channel Set the flash ration of master unitA BorA B C You can conduct flash shooting 51 2 Wireless flash with three slave unit made up by YN565EXiIl Wireless option setting Sc Sn Channel setting 1 2 3 4 Groups setting Set three YN565EX II speedlites as group A group B and group C respectively Setting master and shooting Setting communication channel The master control unit of the flash ratio as lt A B C gt Press the test button of master unit to test whether the flash works normally or not if the slave unit does not fire adjust the angle of the YN565EX II toward the master unit and distance from the master unit Note If the master unit set to lt A B gt is set then set the slave unit in group C will not fire If you have set the three YN565EX II to slave group lt A gt all the three slave units will be controlled by one speedlite in slave group A Slave group A 4 Shooting Examples with Wireless Flash System Master unit YN568EX II G OOEX RT 580 I1 SB 900 800 700 7D 60D 600D with built in flash C comm
4. and automatically power off if it is idle for another 3 minutes after sleep Advanced options function supported by YN565EX II is as following Fn NO 01 SLEP on Auto power off is enabled SP EP Auto power off is disabled Fn NO 03 Fb CL on FEB auto cancel is enabled Fb CL FEB auto cancel is disabled Fn NO 04 Fb 0 Sequence of FEB is 0 Fb 0 Sequence of FEB is 0 om al Fn NO 08 AF on AF assist light is enabled AF AF assist light is disabled Fn NO 09 AP SA1 Automatic identification enabled APS Disabled Fn NO 10 SL Sd 10 Power automatic off of the slave unit is 10 minutes SL Sd 60 Power automatic off of the slave unit is 60 minutes Fn NO 11 SL oF 1H Slave auto power off cancel within 1 hours SL oF 8H Slave auto power off cancel within 8 hours 56 Fn NO 20 So nd on Sound prompt function is enabled So nd Sound prompt function is disabled Fn NO E1 SE oF 3 5 10 30 1H 2H 3H 4H 5H Keeping idle for 3 5 10 30 minutes or 1 2 3 4 5 hours will enter the dormancy mode after it enters the sleep state it powers off automatically after keeps the same idle time SE oF NO dormancy NO automatically turn off Fn NO E2 qu ic Quick turn on shut down function is disabled qu ic on Quick turn on shut down function is enabled Fn NO E3
5. customize the functions of the speedlite according to your shooting preferences AUTOMATIC SETTINGS SAVING YN565EX II can automatically save your current operating settings to convenient your next use LCD PANEL USER INTERFACE ELEGANT APPEARANCE WITH SOLID AND RELIABLE METAL HOT SHOE STAND ll Quick Start If you don t have much time to read the whole user manual we advise you to read this section 1 Please avoid the excessive use of the output with maximum power It can effectively extend the service life of this product It is recommended that the speedlite should be idle for more than 3 minutes when entering the overheating protection 2 You can operate each buttons and observe the changes of the displayed content to understand their respective functions 3 Long press the ZOOM button then through the LEFT or RIGHT button to select the off camera mode Sc n 1 S2 4 Long press the Fn button can set the advanced options function of the flash the setting details please refer to the section of Advanced Options Setting 5 The flash can be operated through the External Flash Function Setting through the Canon camera menu 6 Press the UP DOWN LEFT and RIGHT buttons can quickly adjust the parameters of speedlite at the current mode For some parameters the central OK button is need to press several times for setting 7 This product provides ETTL M MULT mode which can be switched throu
6. get efficient reflection if the reflection surface is not white color cast may appear in photo 11 Use Reflection Board to Take Photos With the reflection of board flash pull out the reflection board and the wide angle diffusion board out from the light head at the same time and then push the wide angle diffusion board back In such case if this product is being used to take photos it will produce a highlighted point on the eyes of the subject and thus make the eyes charming catch light This function can reach optimal effect when the flasher head is up 90 12 Use Wide angle Diffuser Pull out the wide angle diffusion board push back the reflection board and arrange them as per the figure in such case the effect will be softer and more natural IX Specifications Circuit design Guide No Flash mode Trigger mode Wireless triggering distance Flash coverage Vertical rotation angle Horizontal rotation angle Power supply Lighting times Recycle time Color temperature Flash time Flash control External interface External power supply Additional features Dimensions Net weight Contains items Insulated Gate Bipolar Transistor IGBT 58 ISO 100 105mm TTL M Multi Set top Sc Sn 1 S2 20 25m indoor 10 15m outdoor auto 24 28 35 50 70 80 105mm 7 90 degrees 0 270 degrees 4xAAsize batteries Alkaline or Ni MH are usable 100 1500 times AA alkaline cell used Approx 3s AA alka
7. mode you can press the PILOT button to test if the speedlite flash normally When testing the flash the speedlite will give flash at relevant output level in accordance with the chosen output power setting 9 Power Saving Mode YN565EX II is equipped with power saving mode and the mode can be achieved by setting advanced options function For example turn on off the power saving function long press the Advanced options button to enter into the setting 47 state and then select the option numbered 01 with the Up and Down buttons set the state to be SL EP with the Left and Right buttons means the Automatic power off function is closed and when the state is SL EP on means the Automatic power off function is enabled Power saving modes set by advanced option are as following Scope of a Application Options Power Saving Mode All modes Power saving mode is turned off i EP Power saving mode is turned on 10 Power automatic off the slave unit is 10 minutes SL Sd Sc Sn S1 S2 Power automatic off the slave unit is 60 minutes Slave auto power off cancel within 1 hours H OF 5c Sn S1 92 Slave auto power off cancel within 8 hours Sleep after idle time of 3minutes 5 minutes 30 minutes 1 hour 2 3 5 10 30 1H f E1 2H 3H 4H 5H hours 3hours 5hours After it enters the sleep state it powers off SE OF Set top flash automatically after keeps the same idle time ee Set top power sa
8. supply YN565EX II and camera After YN565EX II is installed on the hot shoe of camera turn on the power supply again If it is still unusual please replace the batteries The electronic version of this manual can be got on http www hkyongnuo com The functions of this manual are based on test conditions of our company Further notice will not be given if the design and specifications change The YONGNUO logo in this manual includes the registered trademark or trademark of SHENZHEN YONGNUO PHOTOGRAPHY EQUIPMENT Co Ltd in China or and other countries regions All other trademarks are the property of their respective owners 64
9. the arrow Note Please use four standard specification AA batteries To avoid circuit please do not use damaged batteries 2 Attaching the flash to the Camera Loosen the locking ring by rotating it in the direction of the arrow Slip the speedlite hot shoe stand into the camera hot shoe stand until it stops Tighten the locking ring in the direction of the arrow To detach the speedlite loosen the locking ring then push it from the camera hot shoe e Og mE 7 le f J USEN K VI Basic Functions 1 Basic operations Button Operation Power Switch Press this button for about 2 seconds to turn on or off the power of speedlite When in the normal set top mode and off camera S1 S2 mode the zoom range auto ZOOM button 24 28 35 50 70 80 105mm can be adjusted by short pressing the ZOOM button and long press the button to enter wireless setting state when in off camera Sc Sn mode short press the button can select the setting items Rear curtain sync shortcut button The flash will be switched between rear front curtain sync by each pressing When in normal set top mode the flash mode will be switched between ETTL M Multi by each pressing Blacklight Advanced Short press the button will turned on or off the backlight Long press the button can options button enter into the advanced options setting state of the flash These buttons applied to adjust slave parameter zooming output FEC Stroboscopic RIGH
10. 0 5EV or 0 3 0 5EV mixed as adjustment increment totally 29 grade fine adjustment at most adjust whole grade brightness with the Left and Right button and make fine adjustment with the Up and Down button and the adjustment result will be shown on the LED screen When shooting you only need to set flash brightness adjust the camera and press the shutter the speedlite will flash according to the sync signal of the camera 5 Multi Mode In Multi mode a rapid series of flashes is fired The speedlite will flash according to the output power flash times and frequency you set Use the Left and Right buttons to adjust output power flash times and frequency The adjustment scope of output power is 1 128 1 64 1 32 1 16 1 8 1 4 the scope of flash times is from 1 to 100 and the scope of flash frequency is from 1 to 100 Adjustment method press the OK button to start the flash and use the Left and Right buttons to adjust the flash frequency After the setting is completed press the OK button to confirm the setting The flash times will begin to flash use the Left and Right buttons to adjust the flash times NOTE The charging speed of speedlite will be related slow when the speedlite in low battery which may cause the leakage of the stroboscopic flash In this case please reduce the flash frequency or change new battery 6 Off camera flash mode Sc Sn and 1 S2 Mode Enter the wireless stat
11. T and OK flash count Stroboscopic flash frequency etc please read the subsequent chapters for particular operations PILOT button Flash output brightness can be tested by pressing this button MODE button UP DOWN LEFT Meaning of Charging indicator Method Statues of Charging Meaning Indicator The red light is lit The speedlite is fully charged and can be used The green light is lit The speedlite has not been fully charged Please wait for completion of charging Ee The internal temperature of the flash has risen Please properly reduce the flash See the following table for the meaning of sound The Sound Form Meaning Method Tiek ine The sound indicator is enabled Norval the speedlite is started or flash is OK Three ticks for two times The exposure maybe excessive Adjust exposure compensation Tick tick tick The exposure may be insufficient or change shooting condition Waiting for completion of charging Idle 3 5 minutes for overheating protection remove Tick a long sound The speedlite is fully charged and can be used Tick tick tick THe power is not enough and the speedlite is Replace the batienes going to be shut down The speedlite is in the charging overheating protection prompt Tick tick Tick tick twice 2 Power on and Power offz The power of the speedlite can be turned on or turned off by long pressing the ON OFF button It is recommend that the batteries should be take
12. TI flash mode MULTIPLE TRIGGER MODE SUPPORTED YN565EX II can be triggered by the camera set top built in or master control flashing command S1 and S2 pre flashing SUPPORT AUTOMATIC MANUAL ZOOMING The covered focal length can be varied between auto 24 105mm on the lamp adapter by operating the zoom and adjusting button on the flash light Supports full frame and half frame cameras COMPREHENSIVELY SUPPORTS TTL FUNCTIONS HSS FEC FEB Rear curtain sync FE lock Aperture preview modeling light Canon camera menu accessible HIGH SPEED RECYCLING SYSTEM It just takes 3 seconds to finish a charging cycle after a full level output you can also use external power pack to accelerate the charging speed PROVIDES CHARGING SOCKET FOR EXTERNAL POWER PACK YN565EX II provides charging socket for external power pack to meet your higher demand for charging recycle 34 PC PORT PROVIDED Allow you more easy to make the flash synchronously by using the PC sync line SOUND PROMPT SYSTEM When the sound prompt system is enabled different sound modes will prompt different working conditions of the speedlite so as to allow you to focus on shooting process APERTURE PREVIEW MODELING LIGHT FUNCTION Press the aperture preview button the YN565EX II will send out continuous flash which lasting one second for modeling light ANDVANCED OPTION SETTINGS YN565EX II is equipped with advanced options setting function where you can
13. ander of Nikon s SU 800 and ST E2 Slave unit YONGNUO EX series flash with slave unit flash function which can be created three slave groups at most Use the mini flash stand tripod socket provided to prop up the salve unit YN565EX II Rotate the slave unit YN565EX II to make its wireless sensor faces the master unit Indoors the wireless signal can also be bounce off the wall so there is more leeway in positioning the slave unit s After positioning the YN565EX II be sure to test the wireless flash operation before shooting Do not place any obstacles between the master unit and slave unit s Obstacles can block the transmission of wireless signals 52 VIII Advanced Applications 1 Remote Wireless Flashing Shooting YN565EX II can receive remote wireless signal The longest distance used indoors is up to 25 meters and up to 15 meters used outdoors Please note that the wireless sensor of the YN565EX II should be face to master unit and make sure that the YN565EX II located within the effective range of transmission of the master unit 2 Flash Exposure Compensation In order to make the shooting effect more suitable to your needs you can set the flash exposure compensation through the camera or set on the flash The compensation exposure value can be adjusted through the LEFT and RIGHT buttons on the YN565EX II Every press of the button the compensation value will be displayed on LCD panel The setting range of flash
14. exposure compensation is 5ev 5ev in 1 3 stop increment Note For the Canon version the compensation exposure set on the flash will cover the value set on the camera 3 Exposure Bracketing FEB The FEB function is set through the camera or speedlite After the FEB is set after every 3 photos are taken exposure compensation will be made automatically in the sequence of for example normal gt under over This function helps you improve the success rate of photo taking Through the up and down buttons of YN565EX II can directly adjust the bracketing exposure value Note For FEB set the drive mode of camera to single shot Be sure the flash is ready before shooting 53 4 Rear curtain Sync You can use slow speed shutter to produce trailing smear for the object and the flash light will flash at the moment when the shutter is going to be shut which means the rear curtain sync function For the rear curtain sync setting refer to your camera manual for setting You can turn on or off the rear curtain sync by pressing the High speed rear curtain sync hotkey on panel of YN565EX II Note When YN565xX II is used as wireless flash the rear curtain sync function cannot be set on the flash directly 5 FE Lock Canon To use this function cover the subject for which flash exposure will be locked at the center of the viewfinder of camera press the button lt gt of the flash exposure lock and the flash ligh
15. gh the MODE button IV COMPONENTS DISCRIPTION 1 Reflection board 2 Wide angle diffuser 3 Flash head 4 External power socket It can be connected to the SF 18C or SF 17C external Battery Pack 5 PC port for input 6 Port cover 7 Wireless trigger sensor 8 Battery door 9 AF assist light 10 Locking ring 11 Hot shoe stand LA 12 Hot shoe contact S CA 13 Sound port 14 LCD screen Displays all functions and application setting of the speedlite convenient for users examination and quick setting 15 Rear curtain sync shortcut button The flash will be switched between rear front curtain sync by each pressing 16 ZOOM button Set the flash focal length and the relevant parameters of the slave unit 17 Power switch ON OFF Press this button for about 2 seconds to turn on or off the power of speedlite 18 Selection setting button set Including the Left Right Up Down and central Ok button Through the buttons can set output power exposure compensation exposure bracketing stroboscopic flash times stroboscopic flash frequency focal length range slave unit communicate channel and slave grouping and etc 19 Mode switch button the flash mode will be switched between TTL M Multi by each pressing 20 Blacklight Advanced options button A short press will turned on or off the backligh
16. line cell used 5600k 1 200s 1 20000s 8 levels of output control 1 128 1 1 29levels of fine tuning hot shoe PC port external charging port can be connected to SF 18C or SF 17C charging pack Rear curtain sync FEC FEB exposure lock modeling light lamp holder manual zoom auto zoom sound prompt advanced option automatically saving setting PC port power saving mode over heat protection 60x190x78mm Extended state 380g Flash light 1 protecting bag 1 mini stand 1 manual 1 60 Guide Number of different focal length range at ISO 100 in meters feet Flash Flash Coverage mm V2 V8 X Possible problems during use and solutions 1 The YN565ExX II can t flash Check whether the batteries is installed in the correct orientation Please install the batteries in the correct orientation Check whether the speedlite is attached to the camera Slip the speedlite hot shoe stand into the camera hot shoe stand hard Check the hot shoe contact Clean the contacts Check whether the batteries is exhausted If the charging is not completed within 20 seconds the flash will automatically shutdown Then you need to replace with new batteries 2 YN565EX II can t work as slave unit Check the slave unit setting The YN565EX II must be set to SLAVE Check the slave unit s situation Please position the YN565EX II s within the master s wireless transmission range Adjust the slave unit s angle
17. mode properly the master flash should be set at manual flash and should not use the TTL flash system pre flash function and the red reduction function with multiple flashes 46 Zm sc A enna G1 i TTL Zm sn A GENS 1 S2 mode It is also called pre flash cancel mode This mode is similar with S1 mode but it can neglect the pre flash given by TTL flash Therefore it can support the master flash working in TTL mode In particular if S1 mode cannot flash properly and synchronically with your internal flash you can try to use S2 mode bos A en a a ah a m l Dam mm 2S2 SLAVE The following situation shall be avoided when the S1 and S2 modes are used the red eye reduction function of the main light is used the order mode Nikon or wireless mode Canon of the main light is used the ST E2 is used as the flash controller Otherwise please set the speedlite to Sc Sn mode 7 Menu Access of Camera only for the newer Canon models You can control the speedlite by accessing to camera menu on the newer Canon models which support ETTL On the Flash Control Menu you can set relevant parameters through External flash func setting and External flash C Fn setting for example switch the ETTL mode manual flash mode and MULTI Flash mode Rear curtain Sync Exposure bracketing exposure compensation focal length and advanced setting etc 8 Test Flash No matter in which
18. n out after turned off the speedlite through this button After turning on the power of the speedlite the PILOT indicator light is red which indicates the speedlite is available If in low battery the charging is not completed within 20 seconds the screen will display the low battery icon the speedlite will automatically shutdown indicating it need to change new batteries You can press the PILOT button to test whether the speedlite works normally After use turn off the speedlite by long pressing the ON OFF button for about 2 seconds 3 ETTL Mode In this mode the metering system of this camera will detect flash illumination reflected back from the object so as to automatically adjust the flash output then the subject and background get balanced exposure Supports exposure compensation exposure bracketing rear curtain sync exposure lock modeling light Canon camera menu access function and etc You can set exposure compensation by pressing the Left and Right buttons of the flash the flash exposure compensation range is 5EV 5EV in 1 3 stop precision 4 M Mode In M mode you can set flash brightness according to your preferences and adjust flash brightness by the Left Right Up and Down buttons Adjustment range of flash brightness is 1 128 1 1 and the brightness can be divided into 8 grades each has maximum three grades for fine adjustment and takes 44 mixing grade 0 3EV
19. ssing the ZOOM button While using the main control unit press the ZOOM button then setting the zoom range by pressing the Left and Right buttons 12 Sound Prompt When the sound prompt function is enabled the speedlite will give out different sound to indicate the working state Besides the sound prompt can be turned on or off through the advanced options setting as needed 13 lmaging flash Operate the aperture preview button on the camera theYN565EX II will make one second continuous flash which is modeling light 49 Note Please try to control the continuous modeling lights under 10 times After the operation of consecutive imaging flash the flash need to idle for 10 to 15 minutes to avoid overheating or damage of the flash lamp holder 14 PC Sync port for input By connecting to the PC sync port you can make the flash synchronously 15 Automatic Setting Saving The speedlite will automatically save the current settings which convenient to your next boot Vil Optical transmission wireless flash shooting YN565EX II is fully support wireless flash system one YN565EX II is able to accept internal flash of YN568EX Il 580EXII SB 900 800 700 7D 60D 600D C commander of Nikon build in flash and ST E2 wireless signal at the same time to achieve wireless TTL of multiple flashes and manual flash Sc Indicating that it can only receive wireless signal from Canon system avoiding Nikon system Sn Indicating that it can onl
20. t Long press the button can enter into the advanced options setting state of the flash 21 Charge indicator Test button PILOT Red light indicates charging is completed and flash can work green light indicates charging is being on and press this button the speedlite will emit test flash 22 Flash exposure confirm indicator light When the flash exposure confirm indicator light will shine for about 3 seconds when getting the standard flash exposure lt M Multi gt Manual flash Multi flash lt ETTLA TTL gt C s N s wireless TTLsystem lt B gt Flash exposure compensation Manual flash output level FEB compensation amount lt QD gt Manual zoom Zoom focal length Advanved options number lt L gt Power low indication lt K gt FEB gF Slave zm sd Slave flash lt f gt Sound prompt lt gt Rear curtain sync lt gt Channel 7 Slave group Log cf gt Overheating indication Stroboscopic flash count frequency FEB status Manual flash fine turning increment indicator Advanced options parameters indicator Flash ratio scale V Installation Instruction 1 Install Batteries Slide the Batteries door in the direction of the arrow Insert the batteries according to the label inside battery door and make sure the direction of the batteries polarity is correct Close the battery door in the direction of
21. t will pre flash and the camera will calculate the appropriate flash output data Now you have some time for recomposition after it you can take photo The function can only be used when it is supported by your camera For the setting method refer to your camera manual 6 FV Lock Nikon Set the lt AE L AF L gt function as FV Lock on the camera before using this function At this time you can aim at the object in the viewfinder and then press the lt AE L key or AF L gt key in such case the flash light will pre flash to get the reading of flash exposure for the object after you have confirmed the scene frame press the shutter The function can only be used when it is supported by your camera For the setting of lt AE L and AF L gt refer to your camera manual 7 Advanced Options Setting YN565EX II is equipped with advanced options function you can customize speedlite function as you need set advanced options with button group of the speedlite or camera menu access Setting method of the speedlite 54 Long press the Backlight Fn button to enter into the advanced options function setting state the screen will displays the setting items The advanced options items can be changed through short pressing the UP and DOWN buttons and the parameters can be changed through the LEFT and RIGHT buttons For example lt SE oF 3 gt means used on the set top the speedlite will automatically sleep if it is idle for 3 minutes
22. toward the master unit and distance from the master unit 3 Underexposure or overexposure of photo Check whether the shutter aperture and sensitivity ISO of camera are set too close to the limit of flashing or whether the exposure compensation exposure bracketing and other settings relative with flashing are correct e Because of the differences among different types of cameras and the personal preference you may meet the whole overexposure or underexposure when using this product and so try to adjust it through the flashing compensation or exposure compensation 4 You must set the FEB every time You can access FEB setting through camera menu or lock FEB setting through Fn advanced option setting to avoid that FEB will cancel automatically when completing three shooting tasks The number of setting option is 03 It is ok to set the FEB auto cancel disabled 5 Overexposure of photo Please check whether the FEB sequence is set as 0 You can change the FEB sequence to O through menu accessable or advanced setting Or enable the FEB auto cancel 6 Vignetting appears in photos or only part of the subject is illuminated Please check the current coverage of focal length and make sure if the lens focal length exceeds the coverage range of the flash The product s zooming range is 24 105mm of the medium format system 7 The state of YN565EX Il is abnormal Please try to turn off the power
23. us by long pressing the ZOOM then operate the LEFT and RIGHT buttons to choose Slave four off camera modes Sc Sn S1 S2 for option when the screen display and blink OF The press the 45 OK button to confirm and save the setting four off camera modes Sc Sn S1 S2 for option The four off camera modes Sc Sn S1 S2 can be used as off camera slave unit in order to create multiple lighting effects Sc Sn mode can separately accept YN568EX Il 580EX Il SB 910 900 800 700 7D 60D 600D built in flash Nikon camera C command SU 800 and ST E2 wireless signal supporting 4 channels and realizing TTL and manual wireless flash When using Sc Sn and S1 S2 mode wireless trigger sensors can be adjusted to face master lamp by rotating speedlite holder Before shooting slave unit and master unit should be set at same communication channel Setting method Operate the ZOOM button to select CH flash then choose 1 2 3 4 by pressing the LEFT and RIGHT buttons In Sc Sn mode the flash mode and flash output of the slave unit will be totally controlled by master unit S1 and S2 modes are suitable for MANUAL flash environment and TTL flash environment respectively Under these two modes operating the LEFT and RIGHT buttons to adjust the output brightness is like that in M mode S1 mode In this mode it will work with the first lash synchronously of the master flash with the result consistent with the use of radio slave To use this
24. ving mode off In dormant state the screen will display SE the flash can be waken by pressing any button 10 Overheating Protection If the speedlite is used too frequently the overheating protection function will be triggered the OVERHEATING indicatorwill be displayed on LCD panel And the speedlite will be locked In such case please wait for about 3 48 to 5 minutes before continuing use Please try to use 1 4 output or lower when rapidly shooting is needed to prevent the effect on the shooting Note when continuous shooting the charge indicator will be warn by a red light flashing as the flash internal temperature rises to a certain value At this time the flash recycling time will be extended and it is recommended to appropriately reduce the use intensity of the flash 11 Flash cover range setting Auto Zoom Press the ZOOM button to adjust the flash coverage if lt M gt is not displayed the flash coverage will be set automatically 35mm for default coverage Attaching the speedlite to the camer which supports ETTL system the flash coverage will set automatically to match the lens focal length Manually set the zooming position Press the ZOOM button to adjust the flash coverage if lt M gt is displayed you can adjust the flash coverage manually the flash coverage 24 28 35 50 70 80 105mm Setting method in ordinary set top mode and off camera S1 S2 mode the flash coverage can be adjusted directly by pre
25. y receive wireless signal from Nikon system avoiding Canon system 1 Master Unit Setting The master unit adopts YN568EX II S80EXII SB 900 800 700 7D 60D 600D build in flash C commander of Nikon build in flash and ST E2 wireless signal the relevant setting method please refer to the operation instruction of the master unit 2 Slave Unit Setting Long press the ZOOM button for two seconds when the screen displays OF it means the unit have entered 50 into wireless slave unit state Through the LEFT and RIGHT buttons to set the slave unit SLAVE four off camera modes Sc Sn S1 S2 for choose choose a trigger mode then press OK button to save the setting For the four off camera modes of YN565EX II Sc Sn is equipped with 3 groups A B and C respectively and four communication channels 1 2 3 4 When the YN565EX II as the slave unit in Sc Sn mode through short press the ZOOM button to choose the focal length channel grouping option The selected option will blink then you can set the relevant parameters through short pressing the LEFT and RIGHT button When the YN565EX II set to Sc Sn mode the flash mode flash light ratio exposure compensation exposure bracketing flash lock manual flash output stroboscopic flash and other parameters setting will be totally controlled by the master unit That is to say you can just set the related parameters on the master unit 3 Multi flash Wireless flash Configuration
Download Pdf Manuals
Related Search