97528I (Bea) Memokey NCity 100 codigos V04_13.indd
Contents
1. J 32 Pag 3 n lt FERMAX PROGRAMMING MANUAL Introduction The Memokey s 100 codes are designed for keypad based access control where we want each system user to have their own access code System Features The Memokey has capacity for 100 different codes of variable length between 4 and 6 digits Entering one of the codes via the keypad activates a relay which activates the lock release or another device The system does not allow user codes to be repeated To enter programming mode you must enter aspecial code known as the Master Code If this option is enabled any user can modify their personal access code without knowing the Master code The system has an auxiliary output which supplies a maximum of 125mA to connect activate another device auxiliary relay alarm or a speaker with the memokey itself generating an alarm tone It is equipped with 2 auxiliary inputs for the exit button Free Access Codes Key Press Confirmation via an acoustic tone Pag 4 zn kavy FERMAX The following sections in the Manual explain in detail the configuration and management of each of the system functions Acoustic Tones and Signal Leds The Memokey has a series of acoustic tones and leds which advise as to the system s current status Acoustic Tones Each time an access code programming code or configuration setting is entered the system emits a different tone dependin2. n USER MANUAL Intr ion This equipment includes a keypad which allows the door be opened in addition to the activation of an auxiliary electronic device on entering a personalised code It is possible to programme up to 100 different personalised codes Generally one of these codes is given to each of the system users taking users to be not just the people that frequently access the residence or the area but also those who will be granted access in the future for example in the case of offices In the case of personalised codes we can prohibit the use of any code by a specific user just by deleting the code from the system Management of allthese personalised codes activation deac tivation etc is done by the system administrator NOTES v The SYSTEM ADMINISTRATION can assign a personal code for opening the door and or activate auxiliary devices for any of the authorised users v Users can change their personal code if this option has been enabled by the SYSTEM ADMINISTRATOR v The system has anti sabotage protection such that once 5 erroneous codes have been entered on the keypad it will remain locked for 30 seconds emitting a warning tone throughout this period Pag 31 Mainokeay Keypad Operation On e Code Code to be entered using the keypad to activate the lock release e Emergencies Opens the door and generates an alarm tone where this option has been configured Free Access Entering this code the do
3. free access code by default 1593 the button remains enabled until this code is re entered at which point it will be disabled 1 Enter the free ac cess code 1593 by c k default Bip 3 x 2 Button Enabled sJ Example Enable the free access button 4 Re enter the free Free Access A access code 1593 by default Code 1593 Bip 3 x 5 Button Disabled free access button Pag 20 Vemo RKD FERMAX Enabling Disabling the Exit Buttons A5 A6 The system can be equipped with one or two buttons P1 and P2 which are installed in the interior of the building and allow you to open the door relay activation from inside or activate an additional electronic device installed These buttons can be enabled or disabled in the following way A 1 Enter programming mode Bip 3 x ses Ra Far mr 8 Q 2 Enter the relevant option A5 1 Button Relay 1 A5 or A6 A6 2 Button Relay 2 Pag 21 n o lt FERMAX 3 Enter the associated action 0 Button Disabled 1 Button Enabled Action the door will open Relay 1 2 Button Enabled Action the auxiliary device will be activated if exists Relay 2 3 Button Enabled Action the door will open and the auxiliary device will be ac tivated simultaneously Example Enable exit button 1480 A5 1 1 to open the door Relay Timing lock release activation A2 ______ a
4. 3 Programming the Auxiliary Device Time Relay 2 4 Changing the code length from 4 to 6 figures A5 Enabling Disabling the P1 lock release exit button Relay 1 6 Enabling Disabling the P2 auxiliary device button Relay 2 Enabling Disabling the option for users to A7 I change their code A8 All Purpose Device Auxiliary Output Configuration which is called AUX Delete all Codes Pag 26 Vlamo kady FERMAX Sequence of codes to be entered Code Master 1480 Access Code 4 to 6 Memory digits associated 1480 02 1144 1 Position action 1 2 or 3 00 99 Memory Posi AA tion of the Code to be 1480 AA 02 Deleted New Master Code 1480 A0 1234 A1 A2 A3 New Free Access Code Bi le M J oF loge 149042 00 0 1480 A2 05 1 conds 1480 A4 6 Pag 27 n lt FERMAX Sequence of codes to be entered Code Master 1480 0 Button Disabled 1480 A5 0 1 Button Enabled Lock Release AS Relay 1 2 Button Enabled Activate auxi 1480 A5 2 liary devices Relay 2 3 Button Enabled Activate door 1480 A5 3 auxiliary device simultaneously an User Codes to be Chan 1480 7 All Purpose Device Auxiliary Out A8 put Configuration 0 1 2 3 4 5 1480 8 1 or 6 A9 Code Master 1480 1480 A9 1480 Pag 28 Viamo lt FERMAX TECHNICAL FEATURES Power Supply 12 Vdc Vac Operating Temperature 20 t
5. CA S A U reserves the right to modify the content of this document and the characteristics of the products referred to in it at any time and without prior notice Any modification will be reflected in subsequent editions of this document Pag 2 zn o RK x7 FERMAX PROGRAMMING MANUAL INDEX Introduction nun 4 Function Programming and Configuration 6 Changing the Master 9 Establishing the User Code Length 10 Full Reset of All Codes 12 Restoring Factory Settings 13 Adding or Editing User Codes 14 Deleting User Codes 16 Allowing User Codes to be Changed 17 Changing the Free Access Code 18 Activating Deactivating the Free Access Button 20 Enabling Disabling the Exit Buttons interior 21 Timing Lock Release Activat Relays and Aux 22 Enabling the Auxiliary Output 24 QUICK Programming Guide 26 Technical Features 1 29 Wiring DIagram_ 30 USER MANUAL INDEX 31 Keypad Operalion
6. FEF MAX MANUAL DE INSTALADOR INSTALLER S MANUAL MANUEL D INSTALLATION INSTALLATIONSHANDBUCH MANUAL DO INSTALADOR MANUAL INSTAL eras em e MANUAL MANUEL D INSTALLATION INSTALLATIONSHANDBUC STALADOR MANUAL DE INSTALADOR INSTALLER S MANUA ALLATION INSTALLATIONSHANDBUCH MANUAL DO INSTALA 1 00 D E M EMO KEY STALADOR INSTALLER S MANUAL MANUEL D INSTALLATION SHANDBUGH MANUAL DO INSTALADOR MANUAL DE INSTAL ANUAL MANUEL D INSTALLATION INSTALLATIONSHANDBUC STALADOR MANUAL DE INSTALADOR INSTALLER S MANUA ALLATION INSTALLATIONSHANDBUCH MANUAL DO INSTALA STALADOR INSTALLER S MANUAL MANUEL D INSTALLATION cityline skyline USER amp INSTALLER S MANUAL ENGLISH MEMOKDY KEYPAD MODULE TEST This kit is programmed at the factory with 3 default codes The preprogrammed codes are different for each unit there fore you are the only one to know them You can use this codes to test the equipment operation as well To test the code dial the the one corresponding to the de vice you want to verify CODE ACTION CODE 1 OPEN THE DOOR CODE 2 ACTIVATE THE AUXILIARY DEVICE if any CODE 3 BOTH OPEN THE DOOR AND ACTIVATE THE AUXILIARY DEVICE These codes are shown in a sticker in the back side of the panel controller Code 97528I V04_13 Technical publication of an informative nature published by FERMAX ELECTRONICA S A U As part of its policy of constant improvement FERMAX ELECTRONI
7. g on whether the data entered is correct or not beep x3 correct 9 moc incorrect beep 1 second Lock Release Pag 5 WIaSMoeay FERMAX Signal Leds Has two leds one red and one green F DEFINITION _ Normal mode awaiting access code entry programming Device Powered Up KODE Opening Door Quick Flashes Programming Mode 9 Slow Flashes Awaiting the new value for the selected function Ledon Ledoff 7 lt Leds flashing PROGRAMMING AND CONFIGURATION Programming Mode allows you to modify the system s different settings and configuration Initially the system is programmed by default with a 4 digit code As such the user codes and MASTER code are 4 digits in length If you require greater security you can change the length to 5 or 6 digits See the chapter on Establishing the User Code Length lt FERMAX 1 enter programming mode having beep been in normal mode enter the aj x3 Master Code 1480 by default Jee _ wie The system emits 3 beeps to advise 7 Enter 1480 we are in programming mode and the green led flashes in quick sequence 2 To configure each of the functions beep in programming mode enter the x3 corresponding function code for lt 555 ese example A4 code length L_ Enter A4 At this point the system once again emits 3 beeps to advise that the setting en
8. o 55 C Capacity 100 Access Codes Non Volatile Memory Consumption On standby 40 mA With the lock release relay active 110 mA Panel Connectors 12 Vdc Power Supply C1 R1 relay output 1 potential free C1 relay 1 common wire lock release R1 Normally open NA or normally closed NC contact based on configuration C2 R2 relay output 2 potential free C2 relay 2 common wire lock release R2 Normally open NA or normally closed NC contact based on configuration A auxiliary panic output Collector Output Open Maximum current of 125 mA Pag 29 MEMOKDY ABLING DIAGRAM ALL PURPOSE PAL ar ren OUTPUT TRADE C1R1S1 S2C2R2A 5 A munar POWER SUPPL 12 Vac 12 Vda Ca Memokey Connections PI1 Output Button S1 Button to open the door from inside PI2 Exit Button S2 Auxiliary Electronic Device Activation Button PAL Free Access Button TRADE Optional button to allow free access to the building Notes The operating parameters for the free access auxiliary exit all purpose and lock LOCK RELEASES 12 Vac 12 Vdc release buttons are configurable Use a lock release suitable for the power supply you are going to use Vac or Pag 30
9. ode cannot be a user code and vice versa Pag 9 Mamokxeay Establishing the User and Master Code Length A4 Initially the user codes are 4 digits in length including the MASTER code If you require greater security you can change the length to 5 or 6 digits 7 Enter programming option Bip 3 x a Bip 3 x 3 Indicate the new length Example 6 Digit Access and 1480 A4 6 Master Codes NOTE If once the user codes have been programmed their length is changed to include a greater number of digits additional zeros will be added to the existent codes to bring them in line with the new length 6 0 User Code 4 digits 1234 gt select a greater n of digits For example 6 6 digits 123400 Code Pag 10 MIamo RD FERMAX If once the user codes have been programmed their length is changed to include a fewer number of digits the existent codes will have the last digits removed to bring them in line with the new length e g User Code 6 digits 123456 gt select a fewer n of digits For example 4 4 digits 1234 If additional digits are to be re added to the existing codes the original digits will automatically be re added 6 0 User Code 4 digits 1234 gt select a greater n of digits For example 6 6 digits 123456 Each time the code length is changed the existing codes should be reset to avoid the codes being deleted or overwritten The configuration of code leng
10. or will remain open until the free access code is re entered e Changing the Code Users can change their own personal code if this option has been enabled by the SYSTEM ADMINISTRATOR Pag 32 Memo RKD FERMAX FERMAX User Code lt Emergencies A CODE Free Access AB CODE to be Change Code 5 changed NEW lt This option should be enabled Contact the system administrator Cut out and deliver a copy of this section to each of the users Pag 33 NMIENDKDV FERMAX Pag 34 FERMAX Pag 35 FEF MAX
11. relay should be used Ref 2013 1 Enter program Code Master A ming mode 1480 Bip 3 x 2 Enter the relevant A option Bip 3 x Pag 24 1 lt FERMAX 3 Select the option you require 0 The all purpose output is not used by default The auxiliary output remains de activated 1 Each time a valid code is entered a 1 second pulse will be generated 2 Every time Relay 1 is activated the all purpose device will also activate and will remain activated for 5 seconds longer than the associated device 3 The all purpose output will switch every time a valid code is entered 4 The all purpose output will be activated and will remain active every time you press and a valid keypad code purpose output will remain during 1 minute active 5 The all purpose output activates once 5 erroneous codes are entered in order and will remain active for 5 minutes or until a valid code is entered 6 The all purpose output activates once any key is pressed or deactivates after 15 seconds with inactivity Example Enable auxi 1480 A8 1 u liary output Pag 25 A Bip 3 x x Aa ar u N MIainokeay IDE RAPIDE DE PROGRAMMATION Function I ne Function Description 00 99 Activation and Assignment of Access Codes 100 codes A A Programming the Free Access trades Code A Programming the Relay Activation Time Relay 1 A A Master Code Programming 2
12. tered is correct and the green led flashes in a slow sequence beep 3 Then a new value is entered to be aj x3 assigned to the function selected for See example selecting a code of 6 digits _ Press 6 in length To exit Programing mode at any time press B or allow 20 seconds to elapse without any activity Pag 7 n o lt FERMAX NOTES Default Master Code 4 digit length 1480 5 digit length 14803 6 digit length 148036 If for any reason we need to reset the master code having forgotten the previous one refer to the corresponding chapter Restoring Factory Settings this will be the master code established for this operation Beloware all the system functions and the configuration steps for each of these Pag 8 WIPSMoKeY FERMAX Changing the Master Code A0 The Master code is necessary to enter programming mode The equipment is programmed with a default Master code in factory 1480 by default The procedure to change it is the following 1 Enter programming mode 1480 Bip 3 x 2 Enter the relevant A option Bip 3 x 3 Indicate the new lt Master code Code Bip 3 x Example New Master Access 1480 AO 1234 Code for Program ming 1234 NOTE If you forget the Master code you can reset it to the default code of 1480 as explained in the Restoring the Master Code section 5 er Sa Q PPOP A master c
13. th should be done before setting up the codes on the system This will also effect the MASTER Code and the Free Access Code Pag 11 lt FERMAX Default Master Code 4 digit length 1480 5 digit length 14803 6 digit length 148036 Default Free Access trade Code 4 digit length 1593 5 digit length 15935 6 digit length 159357 Iffor any reason we need to reset any of these codes having forgotten the previous one refer to the corresponding chapter Restoring Factory Settings these are the codes that will be set on undertaking the operation in line with the code length established on the system Full Code Reset A9 This operation allows deletion of allexisting access codes in the system s memory Pag 12 YWI z lt FERMAX 1 Enter programming Code Master mode 1480 Bip 3 x 2 Enter the relevant A option Bip 3 x 3 Re enterthe master code set by default as 1480 to confirm Pay x all codes have been p deleted Example Reset all existing 8 1480 9 1480 cess codes NOTE Resetting is an irreversible operation whereby any previously stored codes cannot be recovered S Ba BS 2o 99 9 2998 Restoring Factory Settings Resetting the Master and Free Access Trade Code where you have forgotten the previous one This operation is carried out by electrically modifying the equipment in the aim of ensuring it is impossible for an
14. tivated simultaneously Example New access code 1111 saved in the 1480 00 1111 1 00 position Pag 15 n lt FERMAX NOTES If the position to be recorded is already in use the new code will replace the old one If the code entered already exists you cannot record and an error message will sound It is very important that a list is prepared of the codes their positions and actions Deleting User Codes AA It is possible to delete a specific user code The procedure to follow is the following 1 Enter programming Code Master mode 1480 Bip 3 x 2 Enter the relevant A option Bip 3 x 3 Enter the position of the access code lt N to be deleted in the Bip 3 x system s memory Example Delete the access code savedin 1480 AA 00 the 00 position esse vos 4 Pag 16 Vemo KDV FERMAX NOTES It is only possible to delete a code if the associated position is known based on which we reiterate the importance of keeping a list with the position data codes and actions programmed on the system Deleting a code is irreversible such that once a code has been deleted it cannot be recovered Allows user codes to be changed by users themselves A7 Users can change their assigned access code for another code of their choice if they wish To do this the following option must be enabled 1 Enter programming Code Master A mode 1480 Bip 3 x 2 Enter the rele
15. uxiliary device activation A3 Initially the relays which will activate the lock release or the auxiliary device are set at 3 seconds The activation time can be changed to any value between 00 and 99 seconds or it can also operate in bistable mode the first valid code activates the relay and the next one deactivates it Pag 22 WMISMoeayVv ate 9 e 1 Enter programming mode 2 Enter the relevant option A2 Relay 1 lock release A3 Relay 2 additional electrical device activa tion 3 Enter the new activation code or select bistable mode 4 Enter 1 if the device is normally deactivated Enter 0 if the device is normally activated Example Change the re lay timing to 5 seconds and normally deactivated A Bip 3 x Code Master 1480 A Bip 3 x 00 Bistable Mode 01 99 01 to 99 se conds A Bip 3x A Bip 3 x 1480 A2 05 0 NOTE The most common case is that of normally deactivated devices such as normal lock releases for example The inversely operated lock releases on the other hand are normally activated devices Pag 23 lt FERMAX Enabling the Auxiliary Output all purpose device AUX A8 This equipment has a free contact auxiliary output which can be connected to a 12 Vdc device with a maximum current of 125 mA to carry out various functions Where the equipmentto be connected does not adjust to these specifications a
16. vant 7 Av option Bip 3 x Example Allows users change their 1480 A7 personal access code NOTE See the User Manual Section Bee RI a 54 Q Pag 17 1 lt FERMAX Changing the Free Access Code A 1 There is a special free access code initially this code is 1593 which allows free access via an additional button It has an associated default relay which activates the lock release This function is especially useful when you want to offer free access to an area to be controlled Entering the free access code by default 1593 the button remains enabled until this code is re entered at which point it will be disabled 1 Enter programming Code Master lt mode 1480 Bip 3 x 2 Enter the relevant option 3 Enter the Free Access New Free Ac 9 Code cess Code Bip 3 x Pag 18 Viamo kDv FERMAX 4 Enter the associated action 1 The door will open Relay 1 2 The auxiliary device will be activated if exists Relay 2 3 The door will open and the auxiliary de vice will be activated simultaneously Example Create a Free Access Code 5251 to 1480 A1 5251 1 open the door NOTE The default free access trade code based on the number of digits will be 4 digit length 1593 5 digit length 15935 6 digit length 159357 Pag 19 lt FERMAX Activate Deactivate the Free Access Button Entering the
17. yone without physical access to the equipment to modify it in any way Pag 13 WISMoeay FERMAX 1 Disconnect the system s power supply 2 Short circuit the S2 and the system If the system is equipped with a PI exit button just press and hold it down refer to the installation diagram 3 Reconnect the system s power supply and remove the short circuit or release the exit button within 5 seconds 4 lf the process has been carried out correctly a double beep will sound and the green light will stay on Next enter the following code A708B9 A double beep will sound and the system will reset itself restoring its factory settings NOTE The restoration of default factory settings does not delete the rest of the information programmed on the system Add or Edit User Codes 00 99 The codes are stored in the memory in sequence position code action Allows up to 100 access codes be stored Pag 14 Viamo lt FERMAX 1 Enter programming Code Master 9 mode 1480 Bip 3 x 2 Enter the position A in the access code s Bip 3 x memory 3 Re enter the new ac cess code New Access The code length must Code Bip 3 x coincide with that esta blished on the system 4 Enter the associated action 1 The door will open Relay 1 2 The auxiliary devi ce will be activated if a exists Relay 2 Bip 3 x 3 The door will open and the auxiliary de vice will be ac
Download Pdf Manuals
Related Search