ultrascan
Contents
1. 120 Ohm The wires must not come into contact with each other otherwise the fixtures will not work at all or will not work properly Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another 1 Ground 1 Ground Occupation of the XLR connection 2 Signal 2 Signal 3 Signal 3 Signal DMX output DMX input XLR mounting socket XLR mounting plug If you are using standart controllers you can connect the DMX output of the controller directly with the DMX input of the first fixture in the DMX chain If you wish to connect DMX controllers with other XLR outputs you need to use adapter cables Building a serial DMX chain Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture Always connect one output with the input of the next fixture until all fixtures are connected Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 Ohm resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture 5 DMX PROTOCOL E 0 255 E of the pan movement pee Tilt a 0 255 Control of the tilt movement proportional C2. The symbol m determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 8 meters Make sure that the area below the installation place is blocked when rigging derigging or servicing the fixture Always fix the fixture with an appropriate safety rope Fix the safety rope at the correct holes only Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened The lamp must never be ignited if the objective lens or any housing cover is open as discharge lamps may explose and emit a high ultraviolet radiation which may cause burns The maximum ambient temperature t 45 C must never be exceeded Otherwise the lamp is switched off and the fixture is out of operation for 5 minutes CAUTION The lens has to be replaced when it is obviously damaged so that its function is impaired e g due to cracks or deep scratches Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation CAUTION The lamp has to be replaced when it is damaged or deformed due to the heat Wait at least 15 minutes before remowing the lamp Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device ar
3. If the power supply cable of this device becomes damaged it has to be replaced by authorized dealers only in order to avoid hazards Should you have further questions please contact your dealer 11 Appendix We believe you will enjoy your ULTRA SCAN We assure you will enjoy this product for years if you follow the instructions given in this manual If you have any questions and comments please do not hesitate to contact us Please note errors and omissions for every information given in this manual excepted Every information is subject to change without prior notice Any claim due to missing or wrong information in this manual is herewith excluded
4. the tSt will start to flash Reset Function Press Enter key to run reset This option enables the ULTRA SCAN to index all effects functions and return to their standard positions 8 1 Special functions calibration Run a test program tSt must flashing Press and keys together and hold them until the display will show message C08 meaning the calibration value of the colour wheel Use and keys to adjust a new calibration value from range C00 C15 the wheel moves in microsteps so you can easilly center current colour Press Menu on the display will appear message G08 meaning the calibration value of the gobo wheel Use and keys to adjust a new calibration value from range GOO G15 the wheel also moves in microsteps so you can easilly center current gobo Now press Menu in order to go back to colour calibration display shows current colour calibration value or press and hold Menu key until the display will show tSt in order to finish calibration procedure 9 Technical specifications Power supply Voltage 100 1 15 208 230 V AC 50 60 Hz FUSE anna T 6 3 A 115V Lamp MSD HSD 250 MSD 250 2 GY 9 5 Optical System High reflecting aluminium coated parabolic reflector Manual focus Standard 19 focused beam angle Bampath Lamp MSD 250 170 Lux Center 10750 sigi Beam Angle 19 T i i i i Distance m 2 5 5 7 5
5. 10 12 5 15 17 5 20 Diameter m 0 83 1 67 2 51 3 35 3 75 4 51 5 26 6 01 Colours 11 dichroic filters plus white UV filter 3 dichroic semicolours filters Colour wheel with variable rotation speed Rotating gobos 9 metal gobos plus open Gobo indexing The gobos have an outside diameter of 16 mm and an image diameter of 13 mm Strobe Strobe effect with variable speed 1 8 flashes per second Motor 6 high quality stepping motors controlled by microprocessors Electronics Intelligent control panel with 3 digit LED display allowing addressing PAN and TILT reverse effect calibration reset of the unit and built in test sequence running Digital serial input DMX 512 6 control channels Channel 1 Horizontal mirror movement Pan Channel 2 Vertical mirror movement Tilt Channel 3 Colour wheel Channel 4 Rotating gobos Channel 5 Rotating gobo index rotating gobo rotation Channel 6 Shutter strobe Housing Easy access to lamp and main components thanks to large opening cover and the projector s modular construction Temperatures Maximum ambient temperature t 45 C Maximum housing temperature t steady state 80 C Minimum distances Min distance from flammable surfaces 0 5m Min distance to lighted object 0 8m Dimensions and weight Lx Wx H 495 x 280 x 170 mm Weight 13 kg 10 Maintenance and cleaning The operator has to make sure that safety relating and machine tech
6. ULTRA SCAN 250 User manual American DI ULTRA SCAN Table of contents Te Sale ly INSIUCHONS Aa ITAK NANU NA 3 2 Operating determinations mamaeemennn ann NN NNA KAKANAN NANANA 4 3 Description of the device maan ahhhht hahhaa 5 A Installat O aaa rerama aeaaaee raaa aaae araea raaa aaia TAa Aaa a raaraa aandra eami Nania 6 4 1 Fitting Exchanging the lampi renra a r 6 4 2 Inserting Exchanging rotating gobos sa aaa NANA ma anakan 7 4 3 Rigging NETONG NA ANA AA AA AG 8 4 4 Connection tothe Mans kam ANAN AABANG paaa 8 4 5 DMX 512 connection connection between fixtures ccccceeeeeeeeeeeeeeeeeeetteeeeeeees 9 5 DMXPROTOCO binan NANANA NAAANINAG 10 6 AdAreSSING Lasa NAA 11 Te GOMLEON BOAT Hika aan 11 o Maiinis ga Ya Aa ORA manda ag AB BA APA NGA AA Aa 11 8 1 Special functions calibration 00 00000 sassssasnaanaaaanananasananananansasssasasanann 12 9 Technical specilficallong cic icicdcciecicnsassaaeanssascusedeenerancndseucednaisausuaaausnvaanadacnaseweecednecedanass 12 10 Maintenance and cleaning Naa NINANG ANI NA NTIN 13 ADAP PON x sicieisiccsindeedisansatddadicsyciniantdaeedessdsesdussdanaiasvsnniaaubacsdacuissvdaabdusudesedaaseuubeasaacnvaus 14 CAUTION Keep this device away from rain and moisture Unplug mains lead before opening the housing FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START UP 1 Safety instructions Every person in
7. alcohol or solvents The front mirror objective lens will require weekly cleaning as smoke fluid tends to building up residues reducing the light output very quickly The cooling fans should be cleaned monthly The gobos may be cleaned with a soft brush The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air jet The dichroic colour filters the rotating gobo wheel and the internal lenses should be cleaned monthly To ensure a proper function of the rotating gobo wheel we recommend lubrication in six month intervals The quantity of oil must not be excessive in order to avoid that oil runs out when the gobo wheel rotates There are no serviceable parts inside the device except for the lamp and the fuse Maintenance and service operations are only to be carried out by authorized dealers Please refer to the instructions under Fitting Exchanging the lamp Replacing the fuse If the lamp burns out the fine wire fuse of the device might fuse too Only replace the fuse by a fuse of the same type and rating Before replacing the fuse unplug mains lead Procedure Step 1 Unscrew the fuse holder on the front panel with a fitting screwdriver from the housing anti clockwise Step 2 Remove the old fuse from the fuseholder Step 3 Install the new fuse in the fuseholder Step 4 Replace the fuseholder in the housing and fix it Should you need any spare parts please use genuine parts
8. ddress to channel 5 the ULTRA SCAN will use the channel 5 to 10 for control Please be sure that you don t have any overlapping channels in order to control each ULTRA SCAN correctly and independently from any other fixture on the DMX data link If two three or more ULTRA SCAN are addressed similarly they will work similarly For address setting follow this procedure 1 Switch On the ULTRA SCAN and wait until the fixture reset has finished rES is flashing at the display 2 Browse through the menu by pressing the and keys until the display shows current addres 001 Confirm by pressing Menu key and 001 will start to flash frequently 3 Use the and keys to select the desired address 4 Confirm by pressing Menu Controlling After having addressed all ULTRA SCAN you may now start operating these via your lighting controller Note After switching on the ULTRA SCAN will automatically detect whether DMX 512 data are received If there are not received these data s at the DMX input the display will start to flash slowly 001 with actually set address This situation can be occurred if there is not connected the 3 PIN XLR plug cable with DMX signal from controller in the input of the ULTRA SCAN the controller is switch Off or is failed the cable or connector is failed or the signal wires are swap in the input connector Note It s necessary to insert the XLR termination plug with 120 Ohm i
9. e forbidden due to safety reasons If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock burns due to ultraviolet radiation lamp explosion crash etc 3 Description of the device 2 Fixation screw for bracket Bracket Fastening screws Objective Mirror akhonND Front panel 1 Fuseholder 2 Powercord 3 DMX input 4 DMX output Function display gt CE Gp UI UI UI 3 Control board Lt II II 1 Menu button 2 Up Down buttons O O O 3 Display Menu 4 Installation 4 1Fitting Exchanging the lamp DANGER Install the lamps with the device switched off only Unplug from mains before Screw A Screw B To insert the lamp MSD HSD 250 or MSD 250 2 open the small cover at the rear panel see the drawing by loosening the 2 Phillips screws A and B on the cover Gently pull out the lamp assembly If changing the lamp remove the old lamp from the socket Insert the lamp to the socket Do not install a lamp with a higher wattage A lamp like this generates temperatures the device is not designed for Damages caused by non ob
10. e lamp until the light is even To reduce a hot spot pull the lamp in by turning all three screws X Y Z clockwise 4 turn at a time until the light is evenly distributed If the light is brighter around the edge than it is in the center or if light output is low the lamp is too far back in the reflector Push the lamp out by turning the screws X Y Z counterclockwise turn at a time the light is bright and evenly distributed 4 2 Inserting Exchanging rotating gobos DANGER Instal the gobos with the device switched off only Unplug from mains before If you wish to use other forms and patterns as the standard gobos or if gobos are to be exchanged please follow the instructions below Remove the fixation ring with an appropriate tool Remove the gobo and insert the new gobo Press the fixation ring together and insert it in front of the gobo CAUTION Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened 4 3 Rigging the fixture The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming deformation The installation must always be secured with a secondary safety attachment e g an appropriate catch net This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails When rigging derigging or servicing the fixtur
11. e staying in the area below the installation place on bridges under high working places and other endangered areas is forbidden The operator has to make sure that safety relating and machine technical installations are approved by an expert before taking into operation for the first time and after changes before taking into operation another time The operator has to make sure that safety relating and machine technical installations are approved by an expert after every four year in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are approved by a skilled person once a year The projector should be installed outside areas where persons may walk by or be seated Important Overhead rigging requires extensive experience including but not limited to calculating working load limits installation material being used and periodic safety inspection of all installation material and the projector If you lack these qualifications do not attempt the installation yourself but instead use a professional structural rigger Improper installation can result in bodily injury and or damage to property The projector has to be installed out of the reach of people If the projector shall be lowered from the ceiling or high joists professional trussing systems have to be used The projector must never be fixed swinging freely in the room Caution Projectors may cause severe injuries when c
12. he electric connection repairs and servicing must be carried out by a qualified employee Do not connect this device to a dimmer pack Do not switch the fixture on and off in short intervals as this would reduce the lamp s life During the initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective Do not touch the device s housing bare hands during its operation housing becomes hot For replacement use lamps and fuses of same type and rating only CAUTION EYEDAMAGES Avoid looking directly into the light source meant especially for epileptics 12 Operating determinations 2 Operating determinations This device was designed for indoor use only If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature When taking the device into operation please make sure that the housing is closed firmly with all the necessary screws tightened up Never run the device without lamp Do not shake the device Avoid brute force when installing or operating the device When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others
13. n the last lighting in the link in order to ensure proper transmission on the DMX data link 7 Control Board The control board situated on the top side of the ULTRA SCAN offers several features You can simply set the lighting address run test show make a reset and also use special functions Browse through the menu by the pressing and keys the display shows step by step these messages 001 rPA rtil tSt rES Press Menu if you wish to select one of them The functions provided are described in the following sections and the function hierarchy is shown below 8 Main functions DMX 512 Address settings The 001 flashes Use the and keys to select required address 001 507 and press Menu to confirm and return to the main menu Pan reverse This function allows you to invert the pan movement Use the and keys to select On if you wish this feature or Off if you don t wish this feature and press Menu to confirm and return to the main menu 11 Tilt reverse This function allows you to invert the tilt movement Use the and keys to select On if you wish this feature or Off if you don t wish this feature and press Menu to confirm and return to the main menu Test program This function allows you to run a special test program without an external controller which show you some possibilities of using ULTRA SCAN Press the Menu key to run the test program
14. nical installations are inspected by an expert after every four years in the course of an acceptance test The operator has to make sure that safety relating and machine technical installations are inspected by a skilled person once a year The following points have to be considered during the inspection 1 All screws used for installing the devices or parts of the device have to be tighly connected and must not be corroded 2 There must not be any deformations on housings fixations and installation spots ceiling suspension trussing 3 Mechanically moved parts like axles eyes and others must not show any traces of wearing e g material abrading or damages and must not rotate with unbalances 4 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed 13 DANGER TO LIFE Disconnect from mains before starting maintenance operation It is absolutely essential that the fixture is kept clean and that dust dirt and smoke fluid residues must not build up on or within the fixture Otherwise the fixture s light output will be significantly reduced Regular cleaning will not only ensure the maximum light output but will also allow the fixture to function reliably throughout its life Please use a moist lint free cloth Never use
15. olours Open white proportional Red proportional Blue proportional Green proportional Yellow proportional Amber proportional Light green proportional Turquoise proportional Dark blue proportional Cyan proportional Pink proportional proportional proportional Red blue proportional Yellow Green proportional Blue purple proportional Forwards rainbow effect from fast to slow proportional No rotation step Backwards rainbow effect from slow to fast proportional Rotating gobos Open hole Rot gobo 1 Rot gobo 2 Rot gobo 3 Rot gobo 4 Rot gobo 5 Rot gobo 6 Rot gobo 7 Rot gobo 8 Rot gobo 9 Rotating gobo index rotating gobo rotation Gobo indexing proportional Forwards gobo rotation from fast to slow proportional No rotation step Backwards gobo rotation from slow to fast proportional Shutter strobe Shutter closed step Gradual adjustment of the light intensity from 0 to 100 proportional Shutter open step Strobe effect fro slow to fast max 8 flashes second proportional Reset step Shutter closed step Pulse effect in sequences with increasing speed proportional Pulse effect in sequences with decreasing speed proportional Random strobe effect from slow to fast proportional Shutter open step 6 Addressing The control board on the top side of the ULTRA SCAN allows you to assign the DMX fixture address which is defined as the first channel from which the ULTRA SCAN will respond to the controller If you set for example the a
16. rashing down If you have doubts concerning the safety of a possible installation do not install the projector Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector s weight Danger of fire When installing the device make sure there is no highly inflammable material decoration articles etc within a distance of min 0 5 m Mount the projector with the mounting bracket to your trussing system using an appropriate clamp The hole in the mounting bracket has a diameter of 10 mm For overhead use always install a safety rope that can hold at least 10 times the weight of the fixture You must only use safety ropes with screw on carabines Pull the safety rope through the hole in the mounting bracket and over the trussing system etc Insert the end in the carabine and tighten the fixation screw Adjust the desired inclination angle via the mounting bracket and fix the bracket screws tightly Connect the fixture to the mains with the power plug 4 4 Connection to the mains The earth has to be connected Connect the fixture to the mains with the enclosed power plug The occupation of the connection cables is as follows cable Pin International Brown Live Blue Neutral Yellow Green Earth DANGER TO LIFE Before taking into operation for the first time the installation has to be approved by an expert 4 5 DMX 512 connection connection between fixtures DMX 512
17. servance are not subject to warranty Please follow the lamp manufacturer s notes Do not touch the glass bulb bare hands during the installation Make sure that the lamp is installed tightly into the lampholder system Reinsert the lamp assembly and tighten the 2 screws again Do not operate this fixture with opened housing cover a Ase any a Oa a ace a Remove the screws A and B for re lamping D Adjust lamp position by turning screws X Y and Z o o WARNING c O Discggfhect the fixture from AC power beforeg lamping Lamp is hot Risk of fire Protect hands ard eyes Wait at least 15min before removing the lamp from the fixture OHOHOH O F Hs o Ca O Q CN O O Z 2 Screw X Screw Z Screw Y Lamp adjustment The lampholder is aligned at the factory Due to differences between lamps fine adjustment may improve light performance Strike the lamp and focus the light on a flat surface wall Center the hot spot the brightest part of the beam using the 3 adjustment screws X Y Z Turn one screw at a time to drag the hot spot diagonally across the projected image If you cannot detect a hot spot adjust th
18. volved with installation and maintenance of this device have to be qualilfied follow the instructions of this manual CAUTION Be careful with your operations With a high voltage you can suffer a dangerous electric shock when touching the wires This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this manual Important The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorized modification to the device Please consider that damages caused by manual modifications to the device are not subject to warranty Never let the power cord come into contact with other cables Handle the power cord and all connections with the mains with particular caution Always plug in the power plug least The power plug has to be accessable after installing the device Make sure that the power cord is never crimped or damaged by sharp edges Check the device and the power cord from time to time Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tugging the power cord This device falls under protection class Therefore it is essential to connect the yellow green conductor to earth T
Download Pdf Manuals
Related Search
ultrascan ultrascan ultrascan pro ultrascan vis ultrascan new hamburg ultrascan uc22 ultrascan mx ultrascan breslau ultrascan ndt ultrascan radiology ultrascan promotions ultrascan ballymount ultrasound mod sims 4 ultrascan medical diagnostic imaging ultrascan pro spectrophotometer