2 Installation
Contents
1. TURBO HD 1080P Turret amp Bullet Camera User Manual UD 6L0201D1999A02 Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual Privacy Notice Surveillance laws vary by jurisdiction Check all relevant laws in your jurisdiction before using this product for surveillance purposes to ensure that your use of this product conforms Please refer to the product specification for camera parameters and functions 0100001050522 Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to corre2. info Industry Canada ICES 003 Compliance This device meets the CAN ICES 3 A NMB 3 A standards requirements 1 Introduction 1 1 Product Features This camera adopts new generation sensor with high sensitivity and advanced circuit board design technology It possesses the features of high resolution low distortion and low noise etc It is extremely suitable for supervisory system and image processing system The main features are as follows High performance CMOS sensor and high resolution bring high quality image Low illumination Support IR cut filter with auto switch OSD menu parameters are configurable Support auto white balance auto gain control electronic shutter control and internal synchronization SMART IR mode 2 8 12mm motorized vari focal lens Advanced 3 axis design meets different installation requirements 1 2 Overview 1 2 1 Overview of Type Camera Power Cable J HD Video Cable OSD Button Lock Button Figure 1 1 Overview of Type I Camera 1 2 2 Overview of Typell Camera Mounting Base Figure 1 2 Overview of Type II Camera 2 Installation Before you start Please make sure that the device in the package is in good condition and all the assembly parts are included Make sure that all the related equipment is power off during the installation Check the specification of the products for the installation environment Check whether the power
3. Menu E EE A coaxial camera controller purchase separately is required to select the menu and adjust the camera parameters E nor After connecting the camera with back end device you can also control the camera with mouse in PTZ control mode The direction keys works as the menu joystick 3 1 Smart Focus Press the menu button to enter the menu interface When the menu interface is not displayed you can press and hold any direction key of the joystick for 3s to enter the focusing interface Move the joystick to adjust the camera lens by the FOCUS FOCUS ZOOM and ZOOM 3 2 VIDEO OUT You can set the frame rate as 25 fps 30fps 3 3 DAY NIGHT Color B W AUTO and EXT are selectable for DAY NIGHT switches Under the mode of the AUTO and EXT you can set the IR LED as Smart and CDS If the IR LED is selected as Smart you can set the bright ness ofthe IR LED DAY NIGHT SPECIAL 1 MODE AUTO 1 PRIVACY ZONE 2 DTON 63 2 MOTION 3 NTOD 63 3 HLC 4 DELAY TIME 20 4 RETURN RET 5 RETURN RET Figure 3 2 DAY NIGHT 3 4 AWB Auto User Push 8000k 6000k 4200k and 3000k are selectable for AWB Under the mode of AUTO you need to set the R G B G Gain and to select an indoor outdoor mode If the AWB mode is select as User You need to set the R G B Gain manually 3 5 AE You can set the AE mode as HOLD DC and ESC Brightness Brightness refers to the brightness of the image Shutter Shutte
4. ances the difference in color and light between parts of animage You can set the value from 0 to 255 Bright Off Bright Off refers to the brightness compensation of the image You can set the bright compensation value as O or 1 Mirror You can set the Mirror status as ON OFF Flip You can set the FLIP status as ON OFF EFFECT 1 COLOR GAIN 200 SYSTEM 2 COLOR HUE 200 1 CAMERA ID 255 3 SHARPNESS 25 RT N 4 CONTRAST 150 3 NAME DISP ON 5 BRIGHT OFF 1 4 LANGUAGE ENG 6 MIRROR ON 5 FACTORY INIT OFF 7 FLIP ON 6 RETURN RET 8 RETURN RET Figure 3 5 EFFECT 3 8 SYSTEM You can setthe camera ID from 0 to 255 Select the ID display and name display status as ON OFF Chinese and English are selectable for the language of the menu You can restore the camera to the default by setting the factory initialization status as ON 3 9 EXIT Exit and Save amp exit are selectable Figure 3 6 SYSTEM
5. ct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the r i supplied accessories too are marked C 3 with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the ROHS Directive 2011 65 EU 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European EE Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis
6. r denotes the speed of the shutter You can set the shutter as AUTO 1 25 1 30 1 50 1 60 1 100 1 120 1 250 1 500 1 1k 1 3k and 1 10k Flicker You can set the flicker status as 5OHZ 60HZ to prevent image flicking BLC BLC bases on the back area to enhance the brightness of the whole image You can set the BLC gain from Oto 16 AGC AGC optimizes the clarity of image in poor light scene The value of AGC can be set from 1 5 LSC LSC corrects the phenomenon where the image gets darkened or blurred on the periphery Figure 3 4 SPECIAL AWB 1 MODE AUTO 2 R G GAIN 255 3 B G GAIN 151 4 RETURN RET Figure 3 3 AWB 3 6 SPECIAL Privacy zone Select a PRIVACY area Set the MASK PAT as OFF GRAY WHITE or BLACK Set the SX EX SY EY value to define the position and size of the area Motion Set the Motion status as ON or OFF Set the SENSITIVITY from 0 to 255 Set the alarm status as ICON TRANCE OFF Set the hold time from O second to 255 seconds HLC HLC supplements the brightness of the peripheral area of the image You can set the mask value and threshold from 0 to 255 3 7 EFFECT Color Gain Color gain adjust this feature to change the saturation of the color You can set the value from Oto 255 Color Hue You can adjust the image HUE from Oto 71 Sharpness Sharpness determines the amount of detail that an imaging system can reproduce You can set the value from 0 to 255 Contrast Contrast enh
7. re suitable for type bullet camera Ceiling mounting will be taken as an example in the section And you can take steps of ceiling mounting as a reference if wall mounting is adopted Steps 1 Drill the screw holes and the cable hole inthe ceiling according to the supplied drill template 2 Hammer the supplied plastic expansion bolt into the screw holes Drill Template 4 Hole B for cables routed through ihe side openi Hole A for cables routed through the ceiling Screw hole 1 for Mounting Base 1 Figure 2 5 Drill Template 3 Route the cables to the cable hole and connect the corresponding cables 4 Fix the camera to the ceiling with the supplied screws Figure 2 6 Fix the Camera to the Ceiling 5 Adjust the surveillance angle 1 Loosen No 1 adjusting screw to adjust the pan position 0 360 2 Tighten No 1 adjusting screw 3 Loosen No 2 adjusting screw to adjust the tilting position 0 90 4 Tighten No 2 adjusting screw 5 Loosen No 3 adjusting screw to adjust the rotation position 0 360 6 Tighten No 3 adjusting screw Figure 2 7 3 axis Adjustment 3 Menu Operation Menu vipeo out awe ae SPECIAL system EXIT AUTO RIVAC USER a a a Cam r EXT cabok Contras LANGUAGE CD 3200K mirror FLIP Figure 3 1 Main
8. supply is matched with your power output to avoid damage Please make sure the wall is strong enough to withstand three times the weight of the camera and the mounting elf the wall is the cement wall you need to insert expansion screws before you install the camera If the wallis the wooden wall you can use self tapping screw to secure the camera if the product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or maintenance by yourself 2 1 Installation of Type Camera Steps 1 Drill the screw holes and the cable hole on the ceiling according to the supplied drill template eo p ap ee i 2 il Miem p late i 7 PAN tor i plate Base k Figure 2 1 The Drill Template 2 Loosen the screws to remove the clip plate and take out the main body WN i Ui Figure 2 2 Remove the Clip Plate 3 Fix the mounting base to the ceiling with PA4 25 screws 4 Route the cables to the cable hole and connect the corresponding cables 5 Install the main body onto the mounting plate and insert the clip plate 6 Tighten the screws with the wrench Figure 2 3 Install the Turret Camera 7 Adjust the camera according to the figure below to get an optimum angle Figure 2 4 3 axis Adjustment 2 2 Installation of Type Il Camera Both wall mounting and ceiling mounting a
Download Pdf Manuals
Related Search