Dynamic Assembly Manual
Contents
1. 2 Y concept2 DYINAMIG UNPACKING AND ASSEMBLY CONCEPT2 DYNAMIC INDOOR ROVVER Step 1 Open the tvvo boxes and remove all the parts Lay out the parts as shovvn belovv and read through the assembly instructions before beginning assembly Note The clear plastic shield located on the top of the flywheel is the optional Wind Shield See Additional Notes for usage on page 9 Wind Shield Foot Carriage Flywheel Return Assembly Shuttle gt Channel Handle Front Leg Monitor Arm Assembly Rear Foot Parts for Assembly 7 m gt 2 PN 2226 127 6 lobe drive x 2 20 penny nails 1 2 patched rev ss FTE PET F 9 PN 2239 127 6 lobe drive x 3 8 patched rev ss Installation leader tape Located in plastic bag with manuals 11 PN 2228 T27 6 lobe drive 1 6 lobe Driver x 1 3 8 patched rev ss concept 2 Page 2 0811 INDOOR ROWER mmm 1 Rail Assembly End Stop w 2 nuts 1 Front Leg End Cap CONCEPT2 COM CONCEPT2 DYNAMIC INDOOR ROVVER Assembly Instructions Step 2 Attach Rear Foot to Flywheel Box Assembly 2 3 8 95 cm PN 2239 Be sure that caster wheels point back as shown in the photo of the assembled Dynamic Indoor Rower on page 9 Install the two screws and tighten snugly See photo A photo A Before turning the flywheel box assembly right side up to continue with assembl2. Performance Monitor PM4 1 Rechargeable Battery Pack 69 concept Page 8 0811 CONCEPT2 COM INDOOR ROWER mmm CONCEPT2 DYNAMIC INDOOR ROVVER Additional Notes Setting the Level of the Dynamic Indoor Rovver The Dynamic ndoor Rovver should be approximately level for the moving components to vvork properly Use the front foot leveling screws to fine tune the level as follows Have a friend watch you row e f the seat tends to stretch the bungee more to the front of the machine than the rear while rowing raise the front of the Dynamic Indoor Rower by turning both front foot leveling screws clockwise several turns f the seat tends to stretch the bungee more to the rear of the machine than the front while rowing lower the front of the Dynamic Indoor Rower by turning both front foot leveling screws counter clockwise several turns Handle Return Tension The design of the Dynamic Indoor Rower has allowed us to reduce the handle return tension significantly compared to our Model D and E Handle return tension inherent in erg rowing is not something we experience in the boat We therefore view the lower tension that can be achieved with this design as a positive feature The tension is set low when we ship the Dynamic Indoor Rower and we suggest rowing with it like this for a while before choosing to tightening the bungee if you really want it to feel more like an erg See page 16 of the Dynamic Indoor Rower User Man
3. plate to the foot carriage extends through the slot and into the shuttle channel Pull the handle all the way out away from the flywheel so that the drive cord is stretched out Straight in the shuttle channel This action will cause the foot carriage to move toward the flywheel see photo L Again be sure the drive cord going to the handle and foot stretcher is not twisted around itself or the drive plate Hint Look into the open end of the shuttle channel to ensure the drive cord is routed properly The drive cord attached to the handle should lay on the floor of the shuttle channel and should not be wrapped around the drive plate photo L Step 7 Install Rail Assembly End Stop 2 1 2 1 27 cm PN 2226 1 x Rail Assembly end stop w 2 nuts b Q Install the rail assembiy end stop on the underside of the rail assembiy Be sure nuts are oriented down toward the floor See photo M Step 8 Attach Front Leg Monitor Arm Assembly 8 1 3 8 3 49 cm PN 2228 Note You may need a second person to assist you nail with aligning the holes BB Assembly ei 4 Front Leg Position the front leg monitor arm assembly at end of les Monitor Arm the shuttle channel and rail assembiy Lift the shuttle Assembly channel and rail assembly up with one hand and slide a them between the two front legs taking care that the handle is extended fully and the drive cord is routed throu
4. CEPT2 DYNAMIC INDOOR ROVVER Assembly continued Pull the black installation leader tape with the generator cable attached back through the rail assembly until it comes out the hole in the underside of the rail assembly See photo T Detach the installation leader tape from the generator cable and plug the generator cable into the black generator on the flywheel See photo U Be careful to position so the retainer clip is as shown in the drawing Note When unplugging the generator cable from generator a small tool may be required to depress the retainer clip Step 10 Install Handle Drive Cord and Front Leg End Cap 2 1 3 8 3 49 cm PN 2228 Run the handle vvith drive cord around the top pulley See photo V Pull the handle toward the foot carrlage until it can be placed in the foot carriage handle hook See photo W q concept 2 INDOOR ROWER mmm Retainer Clip Page 7 0811 photo T Generator Cable photo U photo V CONCEPT2 COM CONCEPT2 DYNAMIC INDOOR ROWER Monitor Arm Front Leg Insert the front leg end cap over open end of front leg End Cap where monitor arm joins the leg Insert screws all the way until the screw head meets the end cap Even though the screws will continue to spin they are as tight as they need to be See photo X Front Leg gt photo Step 11 FOR PM4 ONLY Install Rechargeable Battery Pack in the
5. gh the underside of the pulley Take care not to pinch the drive cord between the pulley guides and photo N the end of the shuttle channel See photo N concept Page 5 0811 CONCEPT2 COM INDOOR ROWER mmm Shuttle Channel CONCEPT2 DYNAMIC INDOOR ROVVER Assembly continued Hint Insert one 20 penny nail through the top fastener hole into the rail assembly and one 20 penny nail through the top fastener hole into the shuttle channel to temporarily align all fastener holes Note that these nails will be replaced with the screws See photo O Once you have the parts aligned insert screws but do not fully tighten until all eight screws are in place Note that you may need to jostle the rail assembly and shuttle channel to get the screws started See photo P Step 9 Install the Generator Cable Uncoil the black installation leader tape by removing the blue tape DO NOT remove the white tape on the end At the back end of the shuttle channel near the flywheel feed the white taped end of the black installation leader tape through the hole in the underside of the rail assembly See photo O Feed it all the way through the rail assembly until it comes out the other end See photo R Partially unwrap the white tape and wrap it around the generator cable plug covering the plug See photo S photo S concept 2 Page 6 0811 2 Eee VO F ROWER mmm CON
6. le channel into the rear leg with the shuttle positioned inside the shuttle channel See image F Be sure the drive cord going to the handle and foot carriage are not twisted around each other image F Start all three 3 8 screws through the flange of the shuttle channel into the corresponding threaded holes in the return mechanism box Do not fully tighten the screws until all three screws are in place See photo G photo G Step 4 Attach Rail Assembly to Flywheel Assembly Note It will be helpful to have a second person assist with this step 4 3 8 95cm PN 2239 Place the rail assembly as shown in photo H Lift the front end of the rail assembly up so that the bottom lies flat against the top of the rear leg photo H Start all four screws Into the threaded holes Do not fully tighten the screws until all four screws are in place See photo Step 5 Attach Seat Bungee photo 1 1 3 8 3 49 cm PN 2228 Insert the screw through the round seat bungee anchor and into the rear leg See photo J Hint You will need to put tension on the seat bungee to align the screw with the threaded hole photo J L concept Page 4 0811 CONCEPT2 COM INDOOR ROWER CONCEPT2 DYNAMIC INDOOR ROVVER Assembly continued Step 6 Slide Foot Carriage onto Rail Assembly Slide foot carriage onto rail assembly as shown In photo K Make sure the drive
7. ual for directions Wind Shield The clear plastic Wind Shield located on the top of the flywheel is an optional accessory designed to deflect air coming from the flywheel away from the rower s body If you preter the additional breeze the Wind Shield can be easily removed by bending It slightly and pulling the tabs at either end out of the flywheel enclosures Note Using the Wind Shield will slightly reduce the current drag factor setting making it feel like you re rowing in a slightly lower damper setting The flywheel damper may be adjusted as needed to maintain the desired feel More about damper setting and drag factor can be found at concept2 com Maintenance It is important that some simple steps be taken to ensure the proper working order and quality feel of the Dynamic Indoor Rower 1 Inspect the drive cord for wear and replace if excessive wear is visible 2 Clean the seat and rail assembly including the foot carriage rails after every workout 3 Clean and lubricate the chain For complete instructions on performing proper maintenance see page 16 of the Dynamic Indoor Rower User Manual Front Leg Monitor Arm Assembly Foot Carriage Wind Shield Rail Assembly lt lt Flywheel AL ce 2 Front Foot P Shuttle Channel Leveling Screws Caster Wheel 69 concept Page 9 0811 CONCEPT2 COM Eee OF ROWER mmm
8. y inspect the chain routing over the chain idler pulleys See image B The chain should be routed around the chain idler pulleys Step 3 Install Shuttle Channel image B 3 3 8 95cm FF PN 2239 Position the foot carrlage and handle away from the flywheel and on either side of the flywheel return assembly with about equal lengths of the drive cord leading to each part See photo C Note The drive cord is a single cord that Is attached to the handle on one end and the foot carriage on the other end photo C Important Pull shuttle down by pulling on drive cord so that the shuttle lies flat on the return mechanism box The drive cord should be routed around the pulley as shown See photo D Remove the cardboard packaging from inside the shuttle channel by sliding it out as indicated by the photo D arrow on the cardboard Note The plastic floor remains in the shuttle channel and is adhered at one end only Position the shuttle channel with the slot facing up and the flange to the flywheel side The end with four holes in it should be away from the flywheel Place the outstretched drive cord through the slot into the shuttle channel so that the foot carriage and the handle are on either side of the shuttle channel as shown See photo E photo E concept Page 3 0811 CONCEPT2 COM INDOOR ROWER mmm CONCEPT2 DYNAMIC INDOOR ROVVER slide the shutt
Download Pdf Manuals
Related Search