2.4G_Digital_TR2080_Elevator
Contents
1. direction Transmitter Transmitter WA A Receiver Receiver 10 VI Specification Wireless transmission for elevator Transmitter Receiver Operation frequency range 2 400 2 483 GHz Channel switch FHSS mode Auto channel selection Video Resolution NTSC 720 X 480 PAL 704 X 576 Modulation 16QAM Data rate Up to 12Mbps Video connector BNC connector Audio connector RCA connector RS485 baudrate 1200 2400 4800 by auto RS485 control protocol PELCO D PELCO P Latency Supply voltage 500mS MAX DC 9 12 V DC 9 12 V Supply current 300mA 12V 300mA 12V Output power Sensitivity 18 2 dBm 80 dBm Video input output level 1 Vp p 75 ohm 1 Vp p 75 ohm Audio input output level 2 4 Vp p 75 ohm 2 2 Vp p 75 ohm Panel antenna Gain 14dBi Beamwidth horizontal 20 degree Beamwidth vertial 20 degree VSWR 1 5 1 Impedance 500 50 Operation temperature 10 C 50 C Measurement 253 L x 253 W x 70mm H 112. SMITTER 1 Install waterproof cable gland fixed boards and antenna accessory on transmitter box Wireless transmission for elevator 2 Locate transmitter box on the elevator Depending situation on bottom or top Wireless transmission for elevator 5 Feed RS485 signal cable through cable gland to connect with transmitter Speed Dome 6 Feed audio signal cable through cable gland to connect with transmitter Mic 7 Feed power cable through cable gland to connect with transmitter Wireless transmission for elevator RECEIVER 1 Install waterproof cable gland fixed boards and antenna accessory on receiver box 2 Locate receiver box on the elevator pit Please notice the grooves of transmitter and receiver are at the same direction Transmitter Transmitter oN n Receiver Receiver Wireless transmission for elevator 4 Feed video signal cable through cable gland to connect with Receiver H gt To DVR video input 6 Feed audio signal cable through cable gland to connect with Receiver Sa To DVR audio input Wireless transmission for elevator 7 Feed power cable through cable gland to connect with Receiver 8 Close and fasten Notice Please make both Transmitter Receiver face to face and keep them on the same
3. Wireless Transmission For Elevator User Manual Wireless transmission for elevator The default value of digital code pairing is done before delivery If the transmission isn t available please accord below steps to re pairing again Pairing process Press the pair keys of transmitter and receiver Both of them will search each other to finish setting with encryption when the Link light is on that means successful Note 1 The pairing is successful after delivery 2 After successful pairing process while the Link light is off it shows that there is no connection between the transmitter and the receiver It means the transmission rage is a little too far to connect between the transmitter and the receiver The reception between the transmitter amp the receiver is not stable Please reduce the distance between the transmitter and the receiver until it works Notes Please connect antenna to Transmitter Receiver firstly then power on Panel antenna is directional Please keep both Panel antennas face to face Elevator moves fast for passengers Before installation please make sure the elevator operation is under controlled by elevator manager Please confirm the power supply voltage from elevator system is available for our wireless devices Wireless transmission for elevator Introduction Wireless transmission for elevator is an easy solution for CCTV in elevator Transmitting Video Aud
4. io RS485 Data for PTZ camera Cable free cost effective and easy maintenance Il Feature e Interference free e Auto pairing with ID e Video Audio and RS485 e Simple installation and setup e Easy to maintain e Long distance transmission Ill Standard Packing Extension cable X 2 Mount Flat X 4 Mount Z type X 2 Adaptor X 2 IV Transmitter Receiver Wireless transmission for elevator Transmitter Receiver are both built in the boxes Together with the boxes Please keep Transmitter Receiver away from water dirt collision or any other damage Before touching Transmitter Receiver please wear gloves to anti static electricity a Transmitter N amp AK on oO N oo 9 To antenna TX means Transmitter Audio Right input RCA Connector Audio Left input RCA Connector Video input BNC Connector RS485 Output RS485 Output DC input 5 5 DC JACK Data LED YELLOW 10 Link LED GREEN 11 Power LED RED 12 Pair button Wireless transmission for elevator b Receiver 1 To antenna 2 RX means Receiver 3 Audio Right input RCA Connector 4 Audio Left Output RCA Connector 5 Video output BNC Connector 6 RS485 input 7 RS485 input 8 DC input 5 5 DC JACK 9 Data LED YELLOW 10 Link LED GREEN 11 Power LED RED 12 Pair button V Installation TRAN
Download Pdf Manuals
Related Search
2.4G_Digital_TR2080_Elevator