Wireless Magnetic Switch Sensor Manual
Contents
1. Product line Raptor Camera Wireless Sensor Version DigitalEye RF DVREye RF Remote VideoEye and Sony LANC RF Systems The PixController wireless magnetic switch sensor incorporates advanced features such as long range low power digital RF radio frequency transmission between the sensor and receiving camera unit This ensures RF transmission through thick foliage for outdoor applications and walls for indoor applications The wireless sensor can be setup to transmit four unique digital address codes The electronics were designed to be extremely battery efficient Using 3 standard AAA alkaline batteries the sensor can be used in the field up to one year with standard use The small packaging of the wireless sensor makes it ideal for covert applications Only the front portion of the sensor needs to be exposed The sensor housing is made from rugged PVC plastic which is completely weather proof There is a 4 20 mounting hole on the bottom of the sensor which can be used with standard bullet camera type tri pod mounts Note Any PixController RF wireless sensor camera system can function with the PixController Wireless Digital PIR Sensor Products sold before September 15 2011 will need to have a crystal changed on the RF receiver electronics These products can be shipped back to PixController Inc to have the crystal replaced Please contact us for more information Transmitter Tube Battery Cover 114 20 Mounting H2. Test mode power the sensor down by turning switch 1 into the off position then turning switch 2 and 3 into the off position 7 Wireless Magnetic Switch Sensor Mounting Options There are several mounting options for the wireless sensor There is a 4 20 mounting hole on the bottom of the sensor which can be used with bullet camera tri pod mounts The sensor can also be placed on the ground but keep in mind that elevating the sensor will increase PIR detection range and range between the wireless sensor and recording electronics Figure 6 Using Bullet Camera Tri Pod Mounts
3. turned on the LED will blink 5 times The default setting is all switches down 2 7 assuming switch 1 is on for sensor in operation mode The sensor is shipped with the PIR sensitivity programmed in medium sensitivity mode 6 2 Setting the Wireless Sensor Address The wireless PIR sensor can be set to send out 4 different address codes A through D DIP switches 2 amp 3 are used to set the sensor address Setting the sensor address code is useful when using multiple sensors with multiple camera units Camera units can be set to respond to certain sensor addresses Sensor Address Switch 2 Switch 3 Address A Down Down Address B Down Up Address C Up Down Address D Up Up Note When changing the sensor address you will need to power the sensor off and back on to take effect 6 3 Setting Range Test Mode Range Test mode puts the sensor into a mode where it will send out trigger commands on 2 second intervals In this mode the PIR sensor is inactive This mode is used to set the range between the wireless PIR sensor and the receiving unit To set Range Test mode start with the wireless sensor in the power down state Turn DIP switches 2 and 3 into the down off position Next power the sensor on by turning switch 1 into up on position Wait for the LED to blink 5 times Next move switches 2 and 3 into the up on position The wireless sensor is now in Range Test mode To take the wireless sensor out of Range
4. 5632 Phone 724 733 0970 Fax 724 733 0860 Email support pixcontroller com Web http www pixcontroller com Table of Contents Warranty Information Wireless Magnetic Switch Sensor Overview Wireless Magnetic Switch Sensor Specs Removing and Replacing the Battery Powering on the Wireless Magnetic Switch Sensor Programming the Wireless Magnetic Switch Sensor DIP Switches 6 1 Powering On Off the Wireless Sensor 6 2 Setting the Wireless Sensor Address 6 3 Setting Range Test Mode 6 4 Adjusting the Digital PIR Sensitivity Wireless Magnetic Switch Sensor Mounting Options 2 Wireless Magnetic Switch Sensor Overview The most basic sensor of any alarm system is a door and window magnetic contact switch This type of contact switch is for normally closed circuits this means that the when the magnets are lined up the switch is closed This type of setup is ideal for monitoring doors windows and sliding doors Measuring 2 48 long and half an inch high they attach with wood or sheet metal screws not included to the frame of the door or window and the case or jam When the magnetic contacts are moved 3 4 apart they will trigger the camera system The wireless magnetic switch sensor comes with a 16 fly lead cable that is connected to the transmitting tube When the sensor is tripped it will send a wireless digital trigger command to a PixController wireless RF camera system This includes but not limited to the UndercoverEye
5. PixController Inc Wireless Magnetic Switch Sensor For Doors Windows and Gates Model SEN 420 S CONTROLLER User s Manual Version 1 00 WARRANTY REGISTRATION PixController Inc warrants products sold by it and guarantees to correct by repair or replacement at our option any defects of material and workmanship which develop under normal and proper use within six 6 months from the date of the original purchase when inspection proves the fault to be of manufacturing Some circuit board components only receive a twelve 12 month warranty All such Products must be returned to our service center This warranty does not apply to any of our Products which have been repaired or altered by unauthorized persons or service centers in any way so as in our judgment to injure their stability or reliability or which have been subject to misuse negligence or accident or which have had their serial number altered effaced or removed We will not assume any expense or liability for repairs made by other parties without our written consent PixController Inc is not responsible for damage to any associated equipment or apparatus nor shall we be held liable for loss of profit or other special damages There is no other guarantee or warranty except as herein stated Returns for any unaffected products are permitted within 14 days from the date of receipt of merchandise After such time items will incur a 15 restocking fee Returns
6. g a small screw driver such as a jewelers screw driver press on switch 1 on the DIP switches as shown in Figure 4 The switches are rocker type switches and you will need to press switch 1 at the top of the switch When the sensor is powered on you will notice the LED turn on and blink 5 times This will let you know that the wireless sensor is going into a 1 minute walk test mode If you place your hand in front of the senor the LED will blink giving you feedback that the PIR sensor is functioning After 1 minute has expired the LED will blink 5 more times and exit walk test mode From this point on there will be no LED activity but the sensor is armed and active Figure 4 Adjusting DIP Switch Settings 6 Programming the Wireless Magnetic Switch Sensor DIP Switches The wireless sensor can easily be programmed by adjusting the small switches on the DIP Switch see Figure 5 The sensor is powered on off by the DIP Switch and you can also adjust the wireless sensor address and PIR detection sensitivity LED DIP Switch Battery Connector Figure 5 DIP Switch Not Used Not Used Not Used Not Used Sensor ID2 Sensor ID 1 Power On Off Figure 5a DIP Switch Functions 6 1 Powering On Off the Wireless Sensor Switch 1 will power on off the wireless PIR sensor unit Putting the switch in the down position will turn the senor off and putting the sensor in the up position will turn the sensor on When the sensor is
7. of wrong ordered items are allowed Returned merchandise will be accepted only if all conditions are met In no event shall PixController Inc be liable for any incidental special indirect or consequential damages whether resulting from the use misuse or inability to use this product or from defects in this product The Buyer is not permitted to tamper or remove any of the Raptor System electronics without voiding this warranty The Buyer his employees or others assumes all risks and liabilities for the operation the use and the misuse of the product described herein and agree to defend and to save the seller harmless from any and all claims arising from any cause whatsoever including seller s negligence for personal injury incurred in connection with the use of the said product PixController Inc reserves the right to discontinue models at any time or change specifications price or design without notice and without incurring any obligation The express warranties are in lieu of all other warranties guarantees promises affirmations or representations express or implied which would be deemed applicable to the goods sold hereunder No express warranties and no implied warranties whether of merchantability fitness for any particular use or purpose against infringement or otherwise except as to title other than those expressly set forth herein shall apply FOR REPAIR CONTACT PixController Inc 1056 Corporate Lane Export PA 1
8. ole Sensor Cable Connector Figure 1 Wireless Switch Sensor Parts Wireless Magnetic Switch Sensor Specs Size 6 0 X 1 30 Battery 3 AAA Battery Life 1 Year Current Draw 107uUA Sleep Mode 4mA Transmit Mode RF Frequency 315MHz RF Range 100 depending on terrain and obstructions Integrated RF Antenna Stainless Steel Sensor Cable Connector 16 Sensor Cable 2 48 long and half an inch high magnetic contacts 34 Operation sensor trigger gap between magnets 1 20 Screw Mounting Hole 4 Adjustable Digital Sensor Address Settings via DIP Switch Power on off via DIP Switch LED indicator for testing battery walk test and range test modes Rugged PVC Waterproof Housing 4 Removing and Replacing the Battery To remove or replace the battery in the wireless sensor unit simply pull off the rubber battery cover located at the rear of the sensor A 3 AAA battery holder will slide out Removing the battery will be necessary to power the unit on off change DIP switch programming settings and replacing the batteries Figure 2 shows how the battery cover and battery is removed and Figure 3 shows the DIP switches inside of the sensor tube Figure 2 Replacing Removing Battery Figure 3 Digital PIR Sensor DIP Switch amp LED 5 Powering on the Wireless Magnetic Switch Sensor To power the wireless senor on you must first remove the battery cover and battery holder from the sensor tube as shown above Usin
Download Pdf Manuals
Related Search