User Manual AirStation Draft-N Wireless USB Adapter WLI-U2
Contents
1. Strength Displays the relative signal strength of the wireless networks Encryption Displays whether the wireless network is using any sort of encryption Click Connect to connect to a highlighted SSID or Refresh to update the list of available wireless devices Client Manager Configuration 1 This dialog will open for you to enter any necessary encryption information The correct encryption type should already be selected automatically in the Encryption Method drop down list Only change this setting if necessary The Encryption Key is where the actual key for the wireless network should be entered Some wireless networks allow you to enter multiple keys four separate fields are available for this If your network only uses one encryption key then please use the first field 1 to enter your key The Register Profile option will store this wireless network in your profiles You will then automatically connect to this network when inside its range This is recommended if you plan on using this wireless network again Press the Connect button once you have completed entering encryption information Client Manager Configuration 1 Profiles Page Click the Profiles tab to open this page Use this page to access your profiles Profiles allow you to save the information associated with a specific wireless network so you can quickly and easily connect to that network when you are in that location T2. Channel The channel that the two wireless clients are using for communication If the Client Manager is not connected to a remote wireless device no channel will be displayed Channels 1 11 may be used Security The type of encryption in use If the Client Manager is not connected to a remote wireless device then No Encryption will be displayed IP Address The IP address of the machine the Client Manager is installed on If the Client Manager is not connected to a network with DHCP then no IP address will be displayed MAC Address The MAC address of the wireless client device inside the computer Client Manager is installed on If no wireless device is present in the computer then no MAC Address will be displayed Signal Strength Displays the signal strength of the peak signal level the wireless adapter receives from the wireless device to which it is connected Next to the signal level is the wireless hardware being used for this measurement 15 Click the Scan tab to open this page Here you can survey the area display available access points and connect to available access points This page includes the following components Wireless SSID The SSID is the name of a wireless network Each wireless device on a network must use identical SSIDs to successfully communicate Wireless Mode Displays available modes for each available remote wireless device
3. Engineers The professional organization which promotes development of electronics technology IP Internet Protocol Address A unique 32 binary digit number that identifies each sender or receiver of information sent in packets Infrastructure A wireless network or other small network in which the wireless network devices are made a part of the network through the Access Point ISP Internet Service Provider A company that provides access to the Internet and other related services IV Initialization Vector The header section of a message packet LAN Local Area Network A group of com puters and peripheral devices connected to share resources LED Light Emitting Diode The lights on a hardware device representing the activity through the ports MAC Medium Access Control Address A unique number that distinguishes network cards Mbps Mega Bits Per Second A measurement of millions of bits per second MDI X Media Dependent Interface Cross over Port on a network hub or switch that crosses the incoming transmit lines with the outgoing receive lines MHz MegaHertz One million cycles per second Glossary 0 PCMCIA Personal Computer Memory Card International Association Card Removable module that adds features to a portable computer Ping Packet Internet Groper An Internet utility used to determine whether a particular IP address is online Plug and Play Hardware that once insta
4. static electricity when working with electrical equipment All guidelines of this manual and of the computer manufacturer must therefore be allowed at all times to ensure the safe use of the equipment FCC CE R amp TTE Intended use This device is a 2 4 GHz wireless LAN transceiver intended for indoor home and office use in USA Canada all EU and EFTA member states EU Countries intended for use This device is intended for indoor home and office use in the following countries Austria Belgium Germany Denmark Spain Greece France Finland Italy Ireland Luxembourg The Netherlands Portugal Sweden United Kingdom Cyprus Czech Republic Estonia Hungry Latvia Lithuania Malta Poland Slovak Republic and Slovenia The device is also authorised for use in all EFTA member states Iceland Liechtenstein Norway and Switzerland EU countries not intended for use None Potential restrictive use This device is a 2 4 GHz wireless LAN transceiver intended for indoor home and office use in all EU and EFTA member states except in France Belgium and Italy where restrictive use applies In Italy the end user should apply for a license at the national spectrum authorities in order to obtain an authorization to use the device for setting up outdoor radio links FCC CE R amp TTE In Belgium there is a restriction in outdoor use The frequency range in which outdoor operation in Belgium is permitted is 2460 2483
5. 5 MHz In France only channels 10 11 12 and 13 are available This device may not be used for setting up outdoor radio links in France For more information see http www anfr fr and or http www art telecom fr FCC CE R amp TTE Warranty Information Buffalo wireless products come with a 2 year limited warranty from the date of purchase Buffalo Technology warrants products in good operating condition for the warranty period This warranty does not include non Buffalo Technology installed components If the Buffalo product malfunctions during the warranty period Buffalo Technology will at its discretion repair or replace the product at no charge provided the product has not been subjected to misuse abuse or non Buffalo Technology authorized alterations modifications or repairs When returning a product include your original proof of purchase Return requests cannot be processed without proof of purchase Shipment of returned product to Buffalo Technology is the responsibility of the purchaser All expressed and implied warranties for the Buffalo product line including but not limited to the warranties of merchantability and fitness for a particular purpose are limited in duration to the above period Under no circumstances shall Buffalo Technology be liable in any way to the user for damages including any lost profits lost savings or other incidental or consequential damages arising out of the use of or inability to use the B
6. P Trivial File Transfer Protocol Simple form of FTP File Transfer Protocol which Uses UDP User Datagram Protocol rather than TCP IP for data transport and provides no security features TKIP Temporal Key Integrity Protocol An encryption method replacing WEP TKIP uses random IV and frequent key exchanges Topology The shape of a LAN Local Area Network or other communications system Twisted Pair Cable that comprises 2 or more pair of insulated wires twisted together UDP User Datagram Protocol A communication method protocol that offers a limited amount of service when messages are exchanged between computers in a network UDP is used as an alternative to TCP IP Uplink Link to the next level up in a communication hierarchy UTP Unshielded Twisted Pair cable Two or more unshielded wires twisted together to form a cable WAN Wide Area Network A networking system covering a wide geographical area WEP Wired Equivalent Privacy An encryption method based on 64 or 128 bit algorithm Web Browser A software program that allows viewing of web pages Glossary Wi Fi Wireless Fidelity An organization that tests and assures interoperability among WLAN devices Wire Speed The maximum speed at which a given packet can be transferred using Ethernet and Fast Ethernet standard specifications WLAN Wireless LAN A LAN topology using wireless devices VPN Virtual Private Network A sec
7. Programs gt gt Buffalo gt gt AirStation Utility gt gt Client Manager The AOSS button is under the Profiles tab AOSS AirStation One Touch Secure System is a simple one touch setup for connecting wireless clients to an access point while enforcing the most secure possible connection encryption type Users no longer need to worry about choosing the proper security protocols IP addresses or SSID AOSS determines the optimal connection and configures itself in seconds If your router doesn t support AOSS turn to page 6 to configure your connection manually with Client Manager or Wireless Zero Config Using AOSS 11 Click the blue AOSS button on the Client Manager s screen The AOSS wizard will appear Now press the AOSS button on the Access Point Hold it down until the AOSS LED begins to flash Using AOSS 12 Once AOSS is complete about 30 seconds the connection is archived as a profile for later use To minimize Client Manager to the system tray click the X in the top right corner Notes AOSS will scan for an AOSS partner for about two minutes If it times out before finding one just press the AOSS buttons again Output power is reduced to 25 of normal during AOSS for security reasons If you re having trouble making an AOSS connection temporarily move the devices closer together AOSS will automatically use the highest level of security available for all currently connected w
8. User Manual AirStation Draft N Wireless USB Adapter WLI U2 G54HG v1 1 2 Insert the AirNavigator CD into the CD ROM drive of your computer The AirNavigator Setup Wizard should launch automatically To launch the AirNavigator Setup Wizard manually click Start then Run Type D Setup exe where D is the drive letter assigned to your CDrom Click OK to launch the wizard Getting Started Select Install Wireless Drivers Installing Drivers 4 Click Next to install a driver for the USB adapter Select Agree and click Next to continue the process after reviewing the license agreement A window will appear prompting the insertion of the Wireless Adapter Plug the included cable into the AirStation Wireless USB Adapter and your PC s USB port Installing Drivers 5 When the Found New Hardware Wizard launches click Next to run the wizard If the Digital Signature Not Found page opens click Yes When the Wireless USB Adapter is successfully installed click Finish Restart your computer if prompted Installing Wireless Drivers Connecting Wireless Clients to your Network Buffalo supports three different methods for connecting your wireless client device to your network If your AP supports AOSS use it to connect simply and securely Install the Client Manager from your AirNavigator CD page 7 and turn to page 10 You ma
9. e extended to accommodate additional workstations RC4 The encryption algorithm that is used in WEP RJ 45 connector An 8 pin connector used between a twisted pair cable and a data transmission device ROM Read Only Memory Permanent memory Router Device that can connect individual LANs and remote sites to a server Roaming The ability to use a wireless device while moving from one access point to another without losing the connection Script A macro or batch file containing instructions and used by a computer to perform a task Server Any computer that makes files or peripheral devices available to users of the network and has a resident Network OS SMTP Simple Mail Transfer Protocol The protocol used to define and deliver electronic mail E mail from one location to another SNMP Simple Network Management Protocol An application layer protocol that outlines the formal structure for communication among network devices Static IP Address A permanent IP address is assigned to a node in a TCP IP network Also known as global IP Glossary 2 STP Shielded Twisted Pair Twisted Pair cable wrapped in a metal sheath to provide extra protection from external interfering signals Subnet Mask An eight byte address divided into 4 parts separated by periods TCP IP Transmission Control Protocol Internet Protocol Protocol used by computers when communicating across the Internet or Intranet TFT
10. ermitted for successful communication IMPORTANT NOTE IC Radiation Exposure Statement This equipment complies with IC RSS 102 radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body This device and its antenna s must not be co located or operating in conjunction with any other antenna or transmitter FCC CE R amp TTE Europe EU Declaration of Conformity This device complies with the essential requirements of the R amp TTE Directive 1999 5 EC The following test methods have been applied in order to prove presumption of compliance with the R amp TTE Directive 1999 5 EC EN 60950 2000 Safety of Information Technology Equipment EN 300 328 2 V1 2 1 2001 12 Technical requirements for spread spectrum radio equipment EN 301 489 17 V1 1 1 2000 09 EMC requirements for spread spectrum radio equipment Taiwan SAR compliance has been established in typical laptop computer s with CardBus slot and product could be used in typical laptop computer with CardBus slot Other application like handheld PC or similar device has not been verified may not comply with related RF exposure rules and such use shall be prohibited Safety This equipment is designed with the utmost care for the safety of those who install and use it However special attention must be paid to the dangers of electric shock and
11. g Hours Monday Friday GMT 9 00 AM 6 00 PM Monday Thursday 9 00 AM 4 30 PM Friday 42 At Buffalo Technology we constantly update our software and firmware For the most recent software firmware driver and technical whitepaper releases available please visit the Buffalo Technology website www buffalotech com Contact Information
12. give more information on using AOSS Client Manager Configuration 20 Windows XP includes the Zero Configuration Service a built in service to configure your wireless clients from within Windows Turn to page 7 if you would rather use Buffalo s Client Manager to configure your wireless client If the Wireless Zero Configuration Service is activated Windows will scan for available wireless access points once the Wireless USB Adapter is properly installed If Windows detects one or more access points a networking icon appears within the system tray One or more wireless networks are available will appear as a caption accompanying the icon To start Wireless Zero Configuration manually click Start gt gt Control Panel gt gt Administrative Tools gt gt Services Select Automatic in the Startup Type field of Wireless Zero Configuration Service Right click the networking icon in the taskbar and select View Available Wireless Networks Select an SSID and click Connect You may need to check the box indicating you are connecting to an unsecured network See page 21 if you need to enter an SSID network name or WEP WPA encryption key Zero Configuration Service 21 Click the Advanced tab to enter an SSID network name or WEP WPA encryption key if necessary To add an SSID network name that is not listed click Add Zero Configuration Service 22 To configure a WEP WPA encryption key se
13. he Profiles page allows you to add delete and edit your profiles as well as import and export data Connect Click the Connect button to connect to the selected profile and return to the Status page Edit Click the Edit button to edit the selected profile s settings The Edit button also allows you to delete profiles that are no longer used or required Add Click the Add button to add a profile manually You will need important information such as SSID encryption settings and network type Client Manager Configuration 1 New Profile Dialog Box Select Profile Select whether the profile is for a wireless or wired connection Profile Name Enter the name you want to associate with the new profile Network Type Select the network mode you want to associate with the new profile Select Infrastructure if your network consists of both wired and wireless devices that communicate through a central device such as an access point Select Ad hoc if your network consists of only wireless devices that communicate with each other directly Network Name SSID Enter the SSID of your network The SSID is the name of your wireless network All wireless devices on a network must use identical SSIDs to successfully associate with other devices on the network MYSSID is an example of a valid SSID Channel The channel setting is only used for Ad hoc connections Whe
14. ick Start gt gt Control Panel gt gt Administrative Tools gt gt Services to open the Services configuration window Select Disabled in the Startup Type field of Wireless Zero Configuration Service to disable the Wireless Zero Configuration Service 24 Antenna Information The WLI U2 G54HG includes a built in directional flat panel antenna For best performance point the face of the flat panel antenna at your access point External antennas cannot be attached to the WLI U2 G54HG 25 Specifications Wireless LAN Interface Standards Compliance Draft N 802 11n Draft Specification 1 0 IEEE 802 11g IEEE 802 11b Communication Protocol Direct Sequence Spread Spectrum DSSS Orthogonal Frequency Division Multiplexing Frequency Range 2 412 2 462 Ghz Transmission Rate Draft N Up to 300 Mbps Auto 802 11g 6 9 12 18 24 36 48 54 Mbps Auto 802 11b 1 2 5 5 11 Mbps Auto Access Mode Infrastructure Mode Security 128 64 Bit WEP WPA PSK TKIP amp AES Other Interface USB 2 0 Environmental Operation 32 113 Fahrenheit 0 45 Celsius Relative Humidity 20 80 non condensing 2 Troubleshooting FAQ What should I do if I already have a version of Client Manager on my PC Update your Client Manager to the version on the CD If you do not update your Client Manager there could be a loss of functionally as some older versions of Client Manager will not work properly with
15. ireless devices If you have trouble connecting with AOSS temporarily disable all personal firewalls on your PC such as ZoneAlarm or Microsoft Personal Firewall These programs may be re enabled after AOSS has finished Using AOSS 1 You may use Client Manager to configure your wireless network Client Manager consists of the Status page the Survey page and the Profiles page You can access each page by clicking the corresponding button on Client Manager In addition to these pages several dialog boxes are also available You can access the Edit Profile dialog box New Profile dialog box IP Configuration dialog box or WEP Configuration dialog box using the Client Manager pages You may also initiate AOSS Status Page Click Status to open this page By default this page is displayed when you start Client Manager Details of connection status are displayed This page only displays connection information no changes to settings are made here This page includes the following components Adapter Name Displays the part number of the wireless adaptor that is being used Client Manager Configuration 14 Client Manager Configuration Network Type Displays whether network is in Ad Hoc or Infrastructure mode Rate The speed of communication between wireless devices If the Client Manager is not connected to a remote wireless device access point or another client no rate will be displayed
16. l Equipment Device that con10BaseT or 100BaseTx 802 3 based Ethernet network that uses UTP Unshield ed twisted pair cable and a star topology 10 is 10 Mbps and 100 is 100 Mbps Dynamic IP Address An IP address that is automatically assigned to a client station in a TCP IP network typically by a DHCP server ESS Extended Service Set A set of two or more BSSs that form a single sub network ESS ID is user identification used in the ESS LAN configuration Ethernet The most widely used architecture for Local Area Networks LANs It is a shared media network architecture The IEEE 802 3 standard details its functionality Ethernet cable A wire similar to telephone cable that carries signals between Ethernet devices File and Print Sharing A Microsoft applica tion that allows computers on a network to share files and printers Firmware Programming inserted into programmable read only memory thus becoming a permanent part of a computing device Frame A fixed block of data transmitted as a single entity Also referred to as packet Full Duplex To transmit on the same channel in both directions simultaneously Gbps Giga Bits per second One billion bits per second Glossary 2 Half duplex To transmit on the same channel in both directions one direction at a time Hub A device which allows connection of computers and other devices to form a LAN IEEE Institute of Electrical and Electronics
17. lect the wireless network and click Configure From the pull down menu select the Network Authentication and Data Encryption types for the wireless network Enter and confirm the Network Key and Key Index Click OK when finished Zero Configuration Service 2 Wireless Zero Configuration Wireless Zero Configuration Service Windows XP Windows XP offers the Wireless Zero Configuration Service to support 802 11b and 802 11g wireless networking This service automatically polls the area for available wireless access points If an available wireless access point is found Windows attempts to connect to the access point If no available wireless access points are found you must manually add the access point information to connect for example when the SSID is not broadcasted Note The Wireless Zero Configuration Service and Client Manager do not function properly together If you want to use Client Manager you must disable the Wireless Zero Configuration Service Enabling the Wireless Zero Configuration Service Click Start gt gt Control Panel gt gt Administrative Tools gt gt Services to open the Services configuration window Select Automatic in the Startup Type field of Wireless Zero Configuration Service to enable the Wireless Zero Configuration Service and click apply Note The default Startup Type value of Wireless Zero Configuration Service is Automatic Disabling the Wireless Zero Configuration Service Cl
18. lled plugged in can immediately be used played as opposed to hardware that requires manual configuration PoE Power over Ethernet A mechanism to send DC power to a device using a CAT5 Ethernet cable PPPoE Point to Point Protocol over Ethernet A specification for connecting users on an Ethernet line to the Internet through a common broadband medium Protocol A standard way of exchanging information between computers MIB II A database containing performance information for each device in a network MIPS Million Instructions Per Second A measurement of processing speed NAT Network Address Translation An internet standard that enables a LAN to use one set of IP addresses for internal traffic and a second set for external traffic NIC Network Interface Card An expansion card that allows a computer can be connected to a network Packet A block of data transferred together Also called a frame or block Packet Filtering Discarding unwanted network traffic based on its originating address or its type PCI Peripheral Component Interconnect A bus that is connected directly to the CPU Glossary 1 RADIUS Remote Authentication Dial In User Service A server that issues authentication key to clients RAM Random Access Memory Non permanent memory Repeater Hub A device that collects strengthens and transmits information to all connected devices allowing the network to b
19. n using an Ad hoc connection select a channel and make sure the other Ad hoc devices are configured to use the same channel Otherwise use Auto Channel Encryption Method Displays the types of encryption available Once encryption is selected you will be required to enter an Encryption Key For the Transmission Key Number 1 is recommended OK Click OK to save your specifications and return to the Profiles page Client Manager Configuration 1 Advanced Profile Options Network Tab Displays the network information tab A static IP can be specified for this wireless profile here It is not recommended to change any of these settings unless specified by an administrator Browser Tab Displays settings to change your browser preferences for this wireless profile A specific home page can be specified when connected to this wireless profile as can specific proxy server addresses Printers Tab Displays the printers tab A specific default printer can be associated to this profile Thus when connected to this profile a specific printer will be used as the default printer OK Click the OK button to save your specifications and return to the Profiles page AOSS Icon To automatically add the USB wireless client to your network just click this icon and then hold down the AOSS button on your wireless router for a few seconds Check your package for an AOSS Manual which will
20. ns session Also referred to as Adhoc Bandwidth The transmission capacity of a computer or a communication channel stated in Megabits per second Mbps BSS Basic Service Set An 802 11 net working framework that includes an Access Point Bus Mastering A system in which the spec ified Input Output device e g NIC Card can perform tasks without the intervention of the CPU Client A PC or workstation on a network Cross Over Wiring A UTP cable that has its transmit and receive pair crossed to allow communications between two devices DCE Data Communications Equipment Hardware used for communication with a Data Terminal Equipment DTE device Default Gateway The IP Address of either the nearest router or server for the LAN Default Parameter Parameter set by the manufacturer Destination Address The address portion of a packet that identifies the intended recipi ent station DHCP Dynamic Host Configuration Protocol Based on BOOTP it uses a pool of IP addresses which it assigns to each device connected to it and retrieves the address when the device becomes dormant for a period of time Glossary 2 DNS Domain Name System System used to map readable machine names into IP addresses Driver Software that interfaces a computer with a specific hardware device DSSS Direct Sequence Spread Spectrum Method of spreading a wireless signal into wide frequency bandwidth DTE Data Termina
21. the G300N Wireless Notebook Adapter Before updating Client Manager uninstall any previous versions of Client Manager To update your Client Manager load the Air Navigator CD and select Install Client Manager Profiles can first be exported from the Profiles tab of Client Manager and then imported back into Client Manager after installation Why won t Client Manager function properly The Wireless Zero Configuration Service in Windows XP conflicts with Client Manager If you use Windows XP make sure that the Wireless Zero Configuration Service is disabled Click Start gt gt Control Panel gt gt Administrative Tools gt gt Services Select Disabled in the Startup Type field of Wireless Zero Configuration Service to enable the Wireless Zero Configuration Service The default value of Wireless Zero Configuration Service is Automatic I have more than one Air Navigator CD Do I need more than one CD No The same Air Navigator CD works with all Buffalo Technology access points and wireless adapters Please use the newest CD you have with the highest revision number on it 2 10BaseT or 100BaseTX 802 3 based Eth ernet network that uses UTP Unshielded twisted pair cable and a star topology 10 is 10 Mbps and 100 is 100 Mbps 802 1x The standard for wireless LAN authentication used between an AP and a client 802 1x with EAP will initiate key handling Ad Hoc Network The wireless network based on a peer to peer communicatio
22. uffalo products Buffalo Technology reserves the right to revise or update its products software or documentation without obligation to notify any individual or entity Please have your proof of purchase receipt to get warranty support All defective products shall be returned with a copy of proof of purchase In no event shall Buffalo Technology s liability exceed the price paid for the product from direct indirect special incidental or consequential damages resulting from the use of the product its accompanying software or its documentation Buffalo Technology does not offer refunds for any product 40 Contact Information North America USA Canada Buffalo Technology USA Inc 4030 West Braker Lane Suite 120 Austin TX 78759 5319 GENERAL INQUIRIES Monday through Friday 8 30am 5 30pm CST Direct 512 794 8533 Toll free 800 456 9799 Fax 512 794 8520 Email sales buffalotech com TECHNICAL SUPPORT North American Technical Support by phone is available 24 hours a day 7 days a week USA and Canada Toll free 866 752 6210 Email info buffalotech com 41 Contact Information Europe Buffalo Technology UK LTD 176 Buckingham Avenue Slough Berkshire SL1 4RD United Kingdom GENERAL INQUIRIES E mail sales buffalo technology com TECHNICAL SUPPORT Phone UK only 08712 50 12 60 Phone 353 61 70 80 50 Email helpdesk buffalo technology ie Calls cost 8 5p per minute Technical Support Operatin
23. urity method to connect remote LAN users to a corporate LAN system Glossary 4 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following t
24. wo conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation The antenna s used for this transmitter must not be co located or operating in conjunction with any other antenna or transmitter FCC CE R amp TTE 5 IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body IC Caution Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power EIRP is not more than that required for successful communication This device has been designed to operate with an antenna having a maximum gain of 2 0 dBi Antenna having a higher gain is strictly prohibited per regulations of Industry Canada The required antenna impedance is 50 ohms To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that p
25. y also use the Client Manager software from your AirNavigator CD to configure your network manually See page 15 for more on Client Manager If you re running Windows XP on your PC you may use its built in Zero Configuration tool to connect to your router AP See page 20 for more on Zero Configuration Client Manager can be used to survey and connect to available access points configure WPA WEP encryption and create connection profiles Note When Client Manager is installed Windows XP Wireless Zero Configuration is automatically disabled Installing Client Manager Insert the AirNavigator CD into the CD ROM drive of you computer If the Air Navigator Setup Wizard does not launch automatically launch it manually by clicking Start and then Run Enter D Setup exe in the dialog box that appears Click OK Select Install Wireless Client Manager Client Manager Client Manager Press Agree to accept the license agreement Press Next to begin the installation Client Manager Click OK when Client Manager installation is complete Press Exit Setup to exit AirNavigator Client Manager is now installed and running Right click on its icon the black antenna to use it 10 The AOSS button for this wireless client is in its Client Manager software Start Client Manager by right clicking on the black antenna icon in your System Tray or by launching the Client Manager from your Start Menu
Download Pdf Manuals
Related Search